Various small fixes to make the Tyan S1846 match the format of

the other supported 440BX boards.

Fix up totally b0rked static device tree in Config.lb.
Drop useless and duplicated failover.c, use global one.
Make CPU init actually work (result: massive speed-up).

Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>



git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2960 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

6 files changed, 151 insertions, 310 deletions

diff --git a/src/mainboard/tyan/s1846/Config.lb b/src/mainboard/tyan/s1846/Config.lb
index 6ef00554d6..09fa980e54 100644
--- a/src/mainboard/tyan/s1846/Config.lb
+++ b/src/mainboard/tyan/s1846/Config.lb
@@ -1,173 +1,131 @@
 ##
-## Compute the location and size of where this firmware image
-## (linuxBIOS plus bootloader) will live in the boot rom chip.
+## This file is part of the LinuxBIOS project.
 ##
-if USE_FALLBACK_IMAGE
-	default ROM_SECTION_SIZE   = FALLBACK_SIZE
-	default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
-else
-	default ROM_SECTION_SIZE   = ( ROM_SIZE - FALLBACK_SIZE )
-	default ROM_SECTION_OFFSET = 0
-end
-
-##
-## Compute the start location and size size of
-## The linuxBIOS bootloader.
-##
-default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
-default PAYLOAD_SIZE            = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
-
-##
-## Compute where this copy of linuxBIOS will start in the boot rom
+## Copyright (C) 2007 Uwe Hermann <uwe@hermann-uwe.de>
 ##
-default _ROMBASE      = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
-
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
 ##
-## Compute a range of ROM that can cached to speed up linuxBIOS,
-## execution speed.
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
 ##
-## XIP_ROM_SIZE must be a power of 2.
-## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
-##
-default XIP_ROM_SIZE=65536
-default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
-
-##
-## Set all of the defaults for an x86 architecture
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
 ##
 
+if USE_FALLBACK_IMAGE
+	default ROM_SECTION_SIZE = FALLBACK_SIZE
+	default ROM_SECTION_OFFSET = (ROM_SIZE - FALLBACK_SIZE)
+else
+	default ROM_SECTION_SIZE = (ROM_SIZE - FALLBACK_SIZE)
+	default ROM_SECTION_OFFSET = 0
+end
+default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE
+				    + ROM_SECTION_OFFSET + 1)
+default PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE)
+default _ROMBASE = (CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE)
+default XIP_ROM_SIZE = 64 * 1024
+default XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE)
 arch i386 end
-
-##
-## Build the objects we have code for in this directory.
-##
-
 driver mainboard.o
-
-#if HAVE_PIRQ_TABLE object irq_tables.o end
-#object reset.o
-
-##
-## Romcc output
-##
+if HAVE_PIRQ_TABLE
+	object irq_tables.o
+end
 makerule ./failover.E
-	depends "$(MAINBOARD)/failover.c ./romcc" 
-	action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+	depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ./romcc"
+	action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
 end
-
 makerule ./failover.inc
-	depends "$(MAINBOARD)/failover.c ./romcc"
-	action "./romcc    -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+	depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ./romcc"
+	action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@"
 end
-
-makerule ./auto.E 
-	depends	"$(MAINBOARD)/auto.c ./romcc" 
-	action	"./romcc -E -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+makerule ./auto.E
+	# depends	"$(MAINBOARD)/auto.c option_table.h ./romcc"
+	depends	"$(MAINBOARD)/auto.c ./romcc"
+	action	"./romcc -E -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
 end
-makerule ./auto.inc 
+makerule ./auto.inc
+	# depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
 	depends "$(MAINBOARD)/auto.c ./romcc"
-	action	"./romcc    -mcpu=i386 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
+	action	"./romcc -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
 end
-
-##
-## Build our 16 bit and 32 bit linuxBIOS entry code
-##
 mainboardinit cpu/x86/16bit/entry16.inc
 mainboardinit cpu/x86/32bit/entry32.inc
 ldscript /cpu/x86/16bit/entry16.lds
 ldscript /cpu/x86/32bit/entry32.lds
-
-##
-## Build our reset vector (This is where linuxBIOS is entered)
-##
-if USE_FALLBACK_IMAGE 
-	mainboardinit cpu/x86/16bit/reset16.inc 
-	ldscript /cpu/x86/16bit/reset16.lds 
+if USE_FALLBACK_IMAGE
+	mainboardinit cpu/x86/16bit/reset16.inc
+	ldscript /cpu/x86/16bit/reset16.lds
 else
-	mainboardinit cpu/x86/32bit/reset32.inc 
-	ldscript /cpu/x86/32bit/reset32.lds 
+	mainboardinit cpu/x86/32bit/reset32.inc
+	ldscript /cpu/x86/32bit/reset32.lds
 end
-
-### Should this be in the northbridge code?
 mainboardinit arch/i386/lib/cpu_reset.inc
-
-##
-## Include an id string (For safe flashing)
-##
 mainboardinit arch/i386/lib/id.inc
 ldscript /arch/i386/lib/id.lds
-
-###
-### This is the early phase of linuxBIOS startup 
-### Things are delicate and we test to see if we should
-### failover to another image.
-###
 if USE_FALLBACK_IMAGE
-	ldscript /arch/i386/lib/failover.lds 
+	ldscript /arch/i386/lib/failover.lds
 	mainboardinit ./failover.inc
 end
-
-###
-### O.k. We aren't just an intermediary anymore!
-###
-
-##
-## Setup RAM
-##
 mainboardinit cpu/x86/fpu/enable_fpu.inc
 mainboardinit cpu/x86/mmx/enable_mmx.inc
 mainboardinit ./auto.inc
 mainboardinit cpu/x86/mmx/disable_mmx.inc
 
-##
-## Include the secondary Configuration files 
-##
 dir /pc80
 config chip.h
 
 chip northbridge/intel/i440bx		# Northbridge
-  device pci_domain 0 on
+  device apic_cluster 0 on		# APIC cluster
+    chip cpu/intel/slot_2		# CPU (FIXME: It's slot 1, actually)
+      device apic 0 on end		# APIC
+    end
+  end
+  device pci_domain 0 on		# PCI domain
     device pci 0.0 on end		# Host bridge
-    device pci 1.0 on end		# AGP bridge
+    device pci 1.0 on end		# PCI/AGP bridge
     chip southbridge/intel/i82371eb	# Southbridge
       device pci 7.0 on			# ISA bridge
         chip superio/nsc/pc87309	# Super I/O
-          device pnp 2e.5 on		# PS/2 keyboard (+ mouse?)
-            io 0x60 = 0x60
-            io 0x62 = 0x64
-            irq 0x70 = 1
-            # irq 0x72 = 12
+          device pnp 2e.0 on		# Floppy
+            io 0x60 = 0x3f0
+            irq 0x70 = 6
+            drq 0x74 = 2
           end
-          device pnp 2e.b on		# Com1
-            io 0x60 = 0x3f8
-            irq 0x70 = 4
+          device pnp 2e.1 on		# Parallel port
+            io 0x60 = 0x378
+            irq 0x70 = 7
           end
-          device pnp 2e.c on		# Com2 / IR
+          device pnp 2e.2 on		# COM2 / IR
             io 0x60 = 0x2f8
             irq 0x70 = 3
           end
-          device pnp 2e.d on		# Parallel port
-            io 0x60 = 0x378
-            irq 0x70 = 7
+          device pnp 2e.3 on		# COM1
+            io 0x60 = 0x3f8
+            irq 0x70 = 4
           end
-          device pnp 2e.e on		# Floppy
-            io 0x60 = 0x3f0
-            irq 0x70 = 6
-            drq 0x74 = 2
+          device pnp 2e.4 on		# Power management
           end
-          device pnp 2e.f on		# PS/2 mouse
+          device pnp 2e.5 on		# PS/2 mouse
             irq 0x70 = 12
           end
+          device pnp 2e.6 on		# PS/2 keyboard
+            io 0x60 = 0x60
+            io 0x62 = 0x64
+            irq 0x70 = 1
+          end
         end
       end
-      device pci 7.1 on end		# IDE
-      device pci 7.2 on end		# USB
+      device pci 7.1 on	end		# IDE
+      device pci 7.2 on	end		# USB
       device pci 7.3 on end		# ACPI
       register "ide0_enable" = "1"
       register "ide1_enable" = "1"
     end
   end
-  chip cpu/intel/slot_2			# CPU
-  end
 end
-
diff --git a/src/mainboard/tyan/s1846/Options.lb b/src/mainboard/tyan/s1846/Options.lb
index 1ce855231e..ebec984879 100644
--- a/src/mainboard/tyan/s1846/Options.lb
+++ b/src/mainboard/tyan/s1846/Options.lb
@@ -1,3 +1,24 @@
+##
+## This file is part of the LinuxBIOS project.
+##
+## Copyright (C) 2007 Uwe Hermann <uwe@hermann-uwe.de>
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+##
+
+uses HAVE_MP_TABLE
 uses HAVE_PIRQ_TABLE
 uses USE_FALLBACK_IMAGE
 uses HAVE_FALLBACK_BOOT
@@ -26,6 +47,7 @@ uses _ROMBASE
 uses _RAMBASE
 uses XIP_ROM_SIZE
 uses XIP_ROM_BASE
+uses HAVE_MP_TABLE
 uses CROSS_COMPILE
 uses CC
 uses HOSTCC
@@ -37,113 +59,41 @@ uses TTYS0_BAUD
 uses TTYS0_BASE
 uses TTYS0_LCS
 uses CONFIG_UDELAY_TSC
-
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 256*1024
-
-###
-### Build options
-###
-
-##
-## Build code for the fallback boot
-##
-default HAVE_FALLBACK_BOOT=1
-
-##
-## Build code to reset the motherboard from linuxBIOS
-##
-default HAVE_HARD_RESET=0
-
-##
-## Build code to export a programmable irq routing table
-##
-default HAVE_PIRQ_TABLE=0
-default IRQ_SLOT_COUNT=4
-
-##
-## Build code to export a CMOS option table
-##
-default HAVE_OPTION_TABLE=0
-
-###
-### LinuxBIOS layout values
-###
-
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
+uses MAINBOARD_VENDOR
+uses MAINBOARD_PART_NUMBER
+uses CONFIG_CONSOLE_VGA
+uses CONFIG_PCI_ROM_RUN
+
+default ROM_SIZE = 256 * 1024
+default HAVE_FALLBACK_BOOT = 1
+default HAVE_MP_TABLE = 0
+default HAVE_HARD_RESET = 0
+default CONFIG_UDELAY_TSC = 1
+default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1
+default HAVE_PIRQ_TABLE = 1
+default IRQ_SLOT_COUNT = 0		# Override this in targets/*/Config.lb.
+default MAINBOARD_VENDOR = "N/A"	# Override this in targets/*/Config.lb.
+default MAINBOARD_PART_NUMBER = "N/A"	# Override this in targets/*/Config.lb.
 default ROM_IMAGE_SIZE = 64 * 1024
 default FALLBACK_SIZE = 128 * 1024
-
-##
-## Use a small 8K stack
-##
-default STACK_SIZE=0x2000
-
-##
-## Use a small 16K heap
-##
-default HEAP_SIZE=0x4000
-
-##
-## Only use the option table in a normal image
-##
+default STACK_SIZE = 8 * 1024
+default HEAP_SIZE = 16 * 1024
+default HAVE_OPTION_TABLE = 0
 #default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
 default USE_OPTION_TABLE = 0
-
 default _RAMBASE = 0x00004000
-
 default CONFIG_ROM_PAYLOAD = 1
-
-##
-## The default compiler
-##
-default CROSS_COMPILE=""
-default CC="$(CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
-
-##
-## The Serial Console
-##
-
-# To Enable the Serial Console
-default CONFIG_CONSOLE_SERIAL8250=1
-
-## Select the serial console baud rate
-default TTYS0_BAUD=115200
-#default TTYS0_BAUD=57600
-#default TTYS0_BAUD=38400
-#default TTYS0_BAUD=19200
-#default TTYS0_BAUD=9600
-#default TTYS0_BAUD=4800
-#default TTYS0_BAUD=2400
-#default TTYS0_BAUD=1200
-
-# Select the serial console base port
-default TTYS0_BASE=0x3f8
-
-# Select the serial protocol
-# This defaults to 8 data bits, 1 stop bit, and no parity
-default TTYS0_LCS=0x3
-
-##
-### Select the linuxBIOS loglevel
-##
-## EMERG      1   system is unusable               
-## ALERT      2   action must be taken immediately 
-## CRIT       3   critical conditions              
-## ERR        4   error conditions                 
-## WARNING    5   warning conditions               
-## NOTICE     6   normal but significant condition 
-## INFO       7   informational                    
-## DEBUG      8   debug-level messages             
-## SPEW       9   Way too many details             
-
-## Request this level of debugging output
-default  DEFAULT_CONSOLE_LOGLEVEL=9
-## At a maximum only compile in this level of debugging
-default  MAXIMUM_CONSOLE_LOGLEVEL=9
-
-default CONFIG_UDELAY_TSC=1
+default CROSS_COMPILE = ""
+default CC = "$(CROSS_COMPILE)gcc -m32"
+default HOSTCC = "gcc"
+default CONFIG_CONSOLE_SERIAL8250 = 1
+default TTYS0_BAUD = 115200
+default TTYS0_BASE = 0x3f8
+default TTYS0_LCS = 0x3			# 8n1
+default DEFAULT_CONSOLE_LOGLEVEL = 9
+default MAXIMUM_CONSOLE_LOGLEVEL = 9
+default CONFIG_CONSOLE_VGA = 1
+default CONFIG_PCI_ROM_RUN = 1
 
 end
-
diff --git a/src/mainboard/tyan/s1846/auto.c b/src/mainboard/tyan/s1846/auto.c
index 7bb2a41788..fdb8f7550b 100644
--- a/src/mainboard/tyan/s1846/auto.c
+++ b/src/mainboard/tyan/s1846/auto.c
@@ -31,12 +31,12 @@
 #include "ram/ramtest.c"
 #include "southbridge/intel/i82371eb/i82371eb_early_smbus.c"
 #include "northbridge/intel/i440bx/raminit.h"
-#include "mainboard/bitworks/ims/debug.c"	// FIXME
+#include "mainboard/asus/mew-vm/debug.c"	/* FIXME */
 #include "pc80/udelay_io.c"
 #include "lib/delay.c"
-#include "superio/nsc/pc87309/pc87309_early_serial.c"
 #include "cpu/x86/mtrr/earlymtrr.c"
 #include "cpu/x86/bist.h"
+#include "superio/nsc/pc87309/pc87309_early_serial.c"
 
 #define SERIAL_DEV PNP_DEV(0x2e, PC87309_SP1)
 
@@ -49,64 +49,24 @@ static inline int spd_read_byte(unsigned int device, unsigned int address)
 #include "northbridge/intel/i440bx/debug.c"
 #include "sdram/generic_sdram.c"
 
-static void enable_mainboard_devices(void)
-{
-	device_t dev = pci_locate_device(PCI_ID(0x8086, 0x7110), 0);
-
-	if (dev == PCI_DEV_INVALID) {
-		die("Southbridge not found!\n");
-	} else {
-		print_debug("Southbridge found!\n");
-	}
-}
-
 static void main(unsigned long bist)
 {
 	static const struct mem_controller memctrl[] = {
 		{
 			.d0 = PCI_DEV(0, 0, 0),
 			.channel0 = {0x50, 0x51, 0x52, 0x53},
-		 },
+		}
 	};
 
-	/* Skip this if there was a built in self test failure. */
-	if (bist == 0) {
+	if (bist == 0)
 		early_mtrr_init();
-	}
 
 	pc87309_enable_serial(SERIAL_DEV, TTYS0_BASE);
 	uart_init();
 	console_init();
-
-	/* Halt if there was a built in self test failure. */
 	report_bist_failure(bist);
-
-	enable_mainboard_devices();
-
 	enable_smbus();
-
-	dump_spd_registers(&memctrl[0]);
-
+	/* dump_spd_registers(&memctrl[0]); */
 	sdram_initialize(sizeof(memctrl) / sizeof(memctrl[0]), memctrl);
-
-	/* Check whether RAM is working.
-	 *
-	 * Do _not_ check the area from 640 KB - 768 KB, as that's not really
-	 * RAM, but rather reserved for the 'Video Buffer Area'.
-	 *
-	 * Other stuff in the range from 640 KB - 1 MB:
-	 *
-	 *  - 640 KB - 768 KB: Video Buffer Area
-	 *  - 768 KB - 896 KB: Expansion Area
-	 *  - 896 KB - 960 KB: Extended System BIOS Area
-	 *  - 960 KB - 1 MB:   Memory (BIOS Area) - System BIOS Area
-	 *
-	 * Trying to check these areas will usually fail, too. However, you
-	 * probably can set the PAM registers of the northbridge to map
-	 * those areas to RAM (read/write). In that case you can use the
-	 * range from 768 KB - 1 MB as normal RAM, and thus check it here.
-	 */
-	ram_check(0x00000000, 0x0009ffff);	/* 0 - 640 KB */
-	ram_check(0x000c0000, 0x00100000);	/* 768 KB - 1 MB */
-	// ram_check(0x00100000, 0x007c0000);   /* 1 MB - 64 MB */
+	/* ram_check(0, 640 * 1024); */
 }
diff --git a/src/mainboard/tyan/s1846/chip.h b/src/mainboard/tyan/s1846/chip.h
index f82ae70333..f53f5dbede 100644
--- a/src/mainboard/tyan/s1846/chip.h
+++ b/src/mainboard/tyan/s1846/chip.h
@@ -19,6 +19,4 @@
  */
 
 extern struct chip_operations mainboard_tyan_s1846_ops;
-
-struct mainboard_tyan_s1846_config {
-};
+struct mainboard_tyan_s1846_config {};
diff --git a/src/mainboard/tyan/s1846/failover.c b/src/mainboard/tyan/s1846/failover.c
index bdcb9eaed2..e69de29bb2 100644
--- a/src/mainboard/tyan/s1846/failover.c
+++ b/src/mainboard/tyan/s1846/failover.c
@@ -1,32 +0,0 @@
-#define ASSEMBLY 1
-#include <stdint.h>
-#include <device/pci_def.h>
-#include <device/pci_ids.h>
-#include <arch/io.h>
-#include "arch/romcc_io.h"
-#include "pc80/mc146818rtc_early.c"
-
-static unsigned long main(unsigned long bist)
-{
-	/* This is the primary cpu how should I boot? */
-	if (do_normal_boot()) {
-		goto normal_image;
-	}
-	else {
-		goto fallback_image;
-	}
- normal_image:
-	asm volatile ("jmp __normal_image" 
-		: /* outputs */ 
-		: "a" (bist) /* inputs */
-		: /* clobbers */
-		);
- cpu_reset:
-	asm volatile ("jmp __cpu_reset"
-		: /* outputs */ 
-		: "a"(bist) /* inputs */
-		: /* clobbers */
-		);
- fallback_image:
-	return bist;
-}
diff --git a/targets/tyan/s1846/Config.lb b/targets/tyan/s1846/Config.lb
index 080f7864ac..56c51a4680 100644
--- a/targets/tyan/s1846/Config.lb
+++ b/targets/tyan/s1846/Config.lb
@@ -22,23 +22,30 @@ target s1846
 mainboard tyan/s1846
 
 option ROM_SIZE = 256 * 1024
-option FALLBACK_SIZE = ROM_SIZE
 
-# romimage "normal"
-# 	option USE_FALLBACK_IMAGE = 0
-# 	option ROM_IMAGE_SIZE = 56 * 1024
-# 	option LINUXBIOS_EXTRA_VERSION = ".0Normal"
-# 	payload /tmp/filo.elf
-# 	# payload /tmp/memtest
-# end
+option MAINBOARD_VENDOR = "Tyan"
+option MAINBOARD_PART_NUMBER = "S1846"
+
+# TODO: Add/fix PIRQ table.
+option HAVE_PIRQ_TABLE = 0
+option IRQ_SLOT_COUNT = 0	# FIXME
+
+option DEFAULT_CONSOLE_LOGLEVEL = 9
+option MAXIMUM_CONSOLE_LOGLEVEL = 9
+
+option CONFIG_CONSOLE_VGA = 1
+option CONFIG_PCI_ROM_RUN = 1
+
+romimage "normal"
+	option USE_FALLBACK_IMAGE = 0
+	option LINUXBIOS_EXTRA_VERSION = ".0Normal"
+	payload /tmp/filo.elf
+end
 
 romimage "fallback"
 	option USE_FALLBACK_IMAGE = 1
-	option ROM_IMAGE_SIZE = 56 * 1024
 	option LINUXBIOS_EXTRA_VERSION = ".0Fallback"
 	payload /tmp/filo.elf
-	# payload /tmp/memtest
 end
 
-# buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback"
-buildrom ./linuxbios.rom ROM_SIZE "fallback"
+buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback"