- Update abuild.sh so it will rebuild successfull builds

- Move pci_set_method out of hardwaremain.c
- Re-add debugging name field but only include the CONFIG_CHIP_NAME is
  enabled.  All instances are now wrapped in CHIP_NAME
- Many minor cleanups so most ports build.


git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1737 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

6 files changed, 127 insertions, 242 deletions

diff --git a/src/mainboard/Iwill/DK8X/Config.lb b/src/mainboard/Iwill/DK8X/Config.lb
index f95725ecbb..903f5c6c62 100644
--- a/src/mainboard/Iwill/DK8X/Config.lb
+++ b/src/mainboard/Iwill/DK8X/Config.lb
@@ -1,110 +1,3 @@
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HARD_RESET_BUS
-uses HARD_RESET_DEVICE
-uses HARD_RESET_FUNCTION
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
-uses CONFIG_MAX_CPUS
-uses CONFIG_IOAPIC
-uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
-uses CONFIG_ROM_STREAM
-uses CONFIG_ROM_STREAM_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE=524288
-
-###
-### Build options
-###
-
-##
-## Build code for the fallback boot
-##
-default HAVE_FALLBACK_BOOT=1
-
-##
-## Build code to reset the motherboard from linuxBIOS
-##
-default HAVE_HARD_RESET=1
-
-default HARD_RESET_BUS=1
-default HARD_RESET_DEVICE=4
-default HARD_RESET_FUNCTION=0
-
-##
-## Build code to export a programmable irq routing table
-##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
-
-##
-## Build code to export an x86 MP table
-## Useful for specifying IRQ routing values
-##
-default HAVE_MP_TABLE=1
-
-##
-## Build code to export a CMOS option table
-##
-default HAVE_OPTION_TABLE=1
-
-##
-## Build code for SMP support
-## Only worry about 2 micro processors
-##
-default CONFIG_SMP=1
-default CONFIG_MAX_CPUS=2
-
-##
-## Build code to setup a generic IOAPIC
-##
-default CONFIG_IOAPIC=1
-
-##
-## Clean up the motherboard id strings
-##
-#default MAINBOARD_PART_NUMBER="HDAMA"
-#default MAINBOARD_VENDOR="ARIMA"
-
-###
-### LinuxBIOS layout values
-###
-
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
-default ROM_IMAGE_SIZE = 65536
-
-##
-## Use a small 8K stack
-##
-default STACK_SIZE=0x2000
-
-##
-## Use a small 16K heap
-##
-default HEAP_SIZE=0x4000
-
-##
-## Only use the option table in a normal image
-##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-
 ##
 ## Compute the location and size of where this firmware image
 ## (linuxBIOS plus bootloader) will live in the boot rom chip.
@@ -123,7 +16,6 @@ end
 ##
 default PAYLOAD_SIZE            = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
 default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
-default CONFIG_ROM_STREAM     = 1
 
 ##
 ## Compute where this copy of linuxBIOS will start in the boot rom
@@ -145,15 +37,12 @@ default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
 ##
 
 arch i386 end
-#cpu k8 end
 
 ##
 ## Build the objects we have code for in this directory.
 ##
 
-#object mainboard.o
 driver mainboard.o
-#object static_devices.o
 if HAVE_MP_TABLE object mptable.o end
 if HAVE_PIRQ_TABLE object irq_tables.o end
 
@@ -161,41 +50,41 @@ if HAVE_PIRQ_TABLE object irq_tables.o end
 ## Romcc output
 ##
 makerule ./failover.E
-	depends "$(MAINBOARD)/failover.c" 
-	action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E"
+	depends "$(MAINBOARD)/failover.c ./romcc" 
+	action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
 end
 
 makerule ./failover.inc
-	depends "./failover.E ./romcc"
-	action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"
+	depends "$(MAINBOARD)/failover.c ./romcc"
+	action "./romcc    -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
 end
 
 makerule ./auto.E 
-	depends	"$(MAINBOARD)/auto.c" 
-	action	"$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
+	depends	"$(MAINBOARD)/auto.c option_table.h ./romcc" 
+	action	"./romcc -E -mcpu=k8 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
 end
 makerule ./auto.inc 
-	depends "./auto.E ./romcc"
-	action	"./romcc -mcpu=k8 -O2 ./auto.E > auto.inc"
+	depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+	action	"./romcc    -mcpu=k8 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
 end
 
 ##
 ## Build our 16 bit and 32 bit linuxBIOS entry code
 ##
-mainboardinit cpu/i386/entry16.inc
-mainboardinit cpu/i386/entry32.inc
-ldscript /cpu/i386/entry16.lds
-ldscript /cpu/i386/entry32.lds
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
 
 ##
 ## Build our reset vector (This is where linuxBIOS is entered)
 ##
 if USE_FALLBACK_IMAGE 
-	mainboardinit cpu/i386/reset16.inc 
-	ldscript /cpu/i386/reset16.lds 
+	mainboardinit cpu/x86/16bit/reset16.inc 
+	ldscript /cpu/x86/16bit/reset16.lds 
 else
-	mainboardinit cpu/i386/reset32.inc 
-	ldscript /cpu/i386/reset32.lds 
+	mainboardinit cpu/x86/32bit/reset32.inc 
+	ldscript /cpu/x86/32bit/reset32.lds 
 end
 
 ### Should this be in the northbridge code?
@@ -207,11 +96,6 @@ mainboardinit arch/i386/lib/cpu_reset.inc
 mainboardinit arch/i386/lib/id.inc
 ldscript /arch/i386/lib/id.lds
 
-##
-## Setup our mtrrs
-##
-mainboardinit cpu/k8/earlymtrr.inc
-
 ###
 ### This is the early phase of linuxBIOS startup 
 ### Things are delicate and we test to see if we should
@@ -229,9 +113,12 @@ end
 ##
 ## Setup RAM
 ##
-mainboardinit cpu/k8/enable_mmx_sse.inc
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+mainboardinit cpu/x86/mmx/enable_mmx.inc
+mainboardinit cpu/x86/sse/enable_sse.inc
 mainboardinit ./auto.inc
-mainboardinit cpu/k8/disable_mmx_sse.inc
+mainboardinit cpu/x86/sse/disable_sse.inc
+mainboardinit cpu/x86/mmx/disable_mmx.inc
 
 ##
 ## Include the secondary Configuration files 
@@ -306,9 +193,3 @@ chip northbridge/amd/amdk8
 	end
 end
 
-##
-## Include the old serial code for those few places that still need it.
-##
-mainboardinit pc80/serial.inc
-mainboardinit arch/i386/lib/console.inc
-
diff --git a/src/mainboard/Iwill/DK8X/auto.c b/src/mainboard/Iwill/DK8X/auto.c
index 9889f23229..b8ca3c82ba 100644
--- a/src/mainboard/Iwill/DK8X/auto.c
+++ b/src/mainboard/Iwill/DK8X/auto.c
@@ -1,25 +1,51 @@
 #define ASSEMBLY 1
 #include <stdint.h>
 #include <device/pci_def.h>
-#include <cpu/p6/apic.h>
 #include <arch/io.h>
-#include <device/pnp.h>
+#include <device/pnp_def.h>
 #include <arch/romcc_io.h>
+#include <cpu/x86/lapic.h>
+#include <arch/cpu.h>
+#include "option_table.h"
+#include "pc80/mc146818rtc_early.c"
 #include "pc80/serial.c"
 #include "arch/i386/lib/console.c"
 #include "ram/ramtest.c"
-#include "northbridge/amd/amdk8/early_ht.c"
+#include "northbridge/amd/amdk8/incoherent_ht.c"
 #include "southbridge/amd/amd8111/amd8111_early_smbus.c"
 #include "northbridge/amd/amdk8/raminit.h"
-#include "cpu/k8/apic_timer.c"
+#include "cpu/amd/model_fxx/apic_timer.c"
 #include "lib/delay.c"
-#include "cpu/p6/boot_cpu.c"
+#include "cpu/x86/lapic/boot_cpu.c"
 #include "northbridge/amd/amdk8/reset_test.c"
 #include "northbridge/amd/amdk8/debug.c"
 #include "northbridge/amd/amdk8/cpu_rev.c"
+#include "superio/NSC/pc87360/pc87360_early_serial.c"
+#include "cpu/amd/mtrr/amd_earlymtrr.c"
+#include "cpu/x86/bist.h"
 
-#define SIO_BASE 0x2e
+#define SERIAL_DEV PNP_DEV(0x2e, PC87360_SP1)
 
+static void hard_reset(void)
+{
+	set_bios_reset();
+
+	/* enable cf9 */
+	pci_write_config8(PCI_DEV(0, 0x04, 3), 0x41, 0xf1);
+	/* reset */
+	outb(0x0e, 0x0cf9);
+}
+
+static void soft_reset(void)
+{
+	set_bios_reset();
+	pci_write_config8(PCI_DEV(0, 0x04, 0), 0x47, 1);
+}
+
+/*
+ * GPIO28 of 8111 will control H0_MEMRESET_L
+ * GPIO29 of 8111 will control H1_MEMRESET_L
+ */
 static void memreset_setup(void)
 {
 	if (is_cpu_pre_c0()) {
@@ -103,68 +129,11 @@ static inline int spd_read_byte(unsigned device, unsigned address)
 #include "sdram/generic_sdram.c"
 #include "northbridge/amd/amdk8/resourcemap.c"
 
-static void enable_lapic(void)
-{
-
-	msr_t msr;
-	msr = rdmsr(0x1b);
-	msr.hi &= 0xffffff00;
-	msr.lo &= 0x000007ff;
-	msr.lo |= APIC_DEFAULT_BASE | (1 << 11);
-	wrmsr(0x1b, msr);
-}
-
-static void stop_this_cpu(void)
-{
-	unsigned apicid;
-	apicid = apic_read(APIC_ID) >> 24;
-
-	/* Send an APIC INIT to myself */
-	apic_write(APIC_ICR2, SET_APIC_DEST_FIELD(apicid));
-	apic_write(APIC_ICR, APIC_INT_LEVELTRIG | APIC_INT_ASSERT | APIC_DM_INIT);
-	/* Wait for the ipi send to finish */
-	apic_wait_icr_idle();
-
-	/* Deassert the APIC INIT */
-	apic_write(APIC_ICR2, SET_APIC_DEST_FIELD(apicid));
-	apic_write(APIC_ICR,  APIC_INT_LEVELTRIG | APIC_DM_INIT);
-	/* Wait for the ipi send to finish */
-	apic_wait_icr_idle();
-
-	/* If I haven't halted spin forever */
-	for(;;) {
-		hlt();
-	}
-}
-
-#define PC87360_FDC  0x00
-#define PC87360_PP   0x01
-#define PC87360_SP2  0x02
-#define PC87360_SP1  0x03
-#define PC87360_SWC  0x04
-#define PC87360_KBCM 0x05
-#define PC87360_KBCK 0x06
-#define PC87360_GPIO 0x07
-#define PC87360_ACB  0x08
-#define PC87360_FSCM 0x09
-#define PC87360_WDT  0x0A
-
-static void pc87360_enable_serial(void)
-{
-	pnp_set_logical_device(SIO_BASE, PC87360_SP1);
-	pnp_set_enable(SIO_BASE, 1);
-	pnp_set_iobase0(SIO_BASE, 0x3f8);
-}
-
 #define FIRST_CPU  1
 #define SECOND_CPU 1
 #define TOTAL_CPUS (FIRST_CPU + SECOND_CPU)
-static void main(void)
+static void main(unsigned long bist)
 {
-	/*
-	 * GPIO28 of 8111 will control H0_MEMRESET_L
-	 * GPIO29 of 8111 will control H1_MEMRESET_L
-	 */
 	static const struct mem_controller cpu[] = {
 #if FIRST_CPU
 		{
@@ -189,22 +158,38 @@ static void main(void)
 		},
 #endif
 	};
-	if (cpu_init_detected()) {
-		asm("jmp __cpu_reset");
-	}
-	enable_lapic();
-	init_timer();
-	if (!boot_cpu()) {
-		stop_this_cpu();
+
+	int needs_reset;
+	if (bist == 0) {
+		/* Skip this if there was a built in self test failure */
+		amd_early_mtrr_init();
+		enable_lapic();
+		init_timer();
+		/* Has this cpu already booted? */
+		if (cpu_init_detected()) {
+			asm volatile ("jmp __cpu_reset");
+		}
+		distinguish_cpu_resets();
+		if (!boot_cpu()) {
+			stop_this_cpu();
+		}
 	}
-	pc87360_enable_serial();
+	/* Setup the console */
+	pc87360_enable_serial(SERIAL_DEV, TTYS0_BASE);
 	uart_init();
 	console_init();
+
+	/* Halt if there was a built in self test failure */
+	report_bist_failure(bist);
+
 	setup_default_resource_map();
-	setup_coherent_ht_domain();
-	enumerate_ht_chain(0);
-	distinguish_cpu_resets(0);
-	
+	needs_reset = setup_coherent_ht_domain();
+	needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0x80);
+	if (needs_reset) {
+		print_info("ht reset -\r\n");
+		soft_reset();
+	}
+
 #if 0
 	print_pci_devices();
 #endif
@@ -212,6 +197,7 @@ static void main(void)
 #if 0
 	dump_spd_registers(&cpu[0]);
 #endif
+
 	memreset_setup();
 	sdram_initialize(sizeof(cpu)/sizeof(cpu[0]), cpu);
 
diff --git a/src/mainboard/Iwill/DK8X/chip.h b/src/mainboard/Iwill/DK8X/chip.h
index c0f74846ef..7710024cca 100644
--- a/src/mainboard/Iwill/DK8X/chip.h
+++ b/src/mainboard/Iwill/DK8X/chip.h
@@ -1,5 +1,5 @@
-extern struct chip_operations mainboard_arima_hdama_control;
+extern struct chip_operations mainboard_Iwill_DK8X_ops;
 
-struct mainboard_arima_hdama_config {
+struct mainboard_Iwill_DK8X_config {
 	int nothing;
 };
diff --git a/src/mainboard/Iwill/DK8X/cmos.layout b/src/mainboard/Iwill/DK8X/cmos.layout
index 5ba4c032c1..1ab6187288 100644
--- a/src/mainboard/Iwill/DK8X/cmos.layout
+++ b/src/mainboard/Iwill/DK8X/cmos.layout
@@ -29,6 +29,9 @@ entries
 386          1       e       1        ECC_memory
 388          4       r       0        reboot_bits
 392          3       e       5        baud_rate
+395          1       e       1        hw_scrubber
+396          1       e       1        interleave_chip_selects
+397          2       e       8        max_mem_clock
 400          1       e       1        power_on_after_fail
 412          4       e       6        debug_level
 416          4       e       7        boot_first
@@ -36,7 +39,15 @@ entries
 424          4       e       7        boot_third
 428          4       h       0        boot_index
 432	     8       h       0        boot_countdown
-1008         16      h       0        check_sum
+440          4       e       9        slow_cpu
+444          1       e       1        nmi
+445          1       e       1        iommu
+728        256       h       0        user_data
+984         16       h       0        check_sum
+# Reserve the extended AMD configuration registers
+1000        24       r       0        reserved_memory
+
+
 
 enumerations
 
@@ -66,9 +77,19 @@ enumerations
 7     9     Fallback_HDD
 7     10    Fallback_Floppy
 #7     3     ROM
+8     0     200Mhz
+8     1     166Mhz
+8     2     133Mhz
+8     3     100Mhz
+9     0     off
+9     1     87.5%
+9     2     75.0%
+9     3     62.5%
+9     4     50.0%
+9     5     37.5%
+9     6     25.0%
+9     7     12.5%
 
 checksums
 
-checksum 392 1007 1008
-
-
+checksum 392 983 984
diff --git a/src/mainboard/Iwill/DK8X/mainboard.c b/src/mainboard/Iwill/DK8X/mainboard.c
index 845285c881..a1b05d0943 100644
--- a/src/mainboard/Iwill/DK8X/mainboard.c
+++ b/src/mainboard/Iwill/DK8X/mainboard.c
@@ -3,12 +3,9 @@
 #include <device/pci.h>
 #include <device/pci_ids.h>
 #include <device/pci_ops.h>
-
-#include <arch/io.h>
-#include "../../../northbridge/amd/amdk8/northbridge.h"
 #include "chip.h"
 
-struct chip_operations mainboard_arima_hdama_control = {
-	.name      = "Arima HDAMA mainboard ",
+struct chip_operations mainboard_Iwill_DK8X_ops = {
+	CHIP_NAME("Iwill DK8X mainboard")
 };
 
diff --git a/src/mainboard/Iwill/DK8X/mptable.c b/src/mainboard/Iwill/DK8X/mptable.c
index bd9df2e3ac..34e6037c21 100644
--- a/src/mainboard/Iwill/DK8X/mptable.c
+++ b/src/mainboard/Iwill/DK8X/mptable.c
@@ -4,11 +4,11 @@
 #include <string.h>
 #include <stdint.h>
 
-void *smp_write_config_table(void *v, unsigned long * processor_map)
+void *smp_write_config_table(void *v)
 {
 	static const char sig[4] = "PCMP";
-	static const char oem[8] = "LNXI    ";
-	static const char productid[12] = "HDAMA       ";
+	static const char oem[8] = "IWILL   ";
+	static const char productid[12] = "DK8X        ";
 	struct mp_config_table *mc;
 	unsigned char bus_num;
 	unsigned char bus_isa;
@@ -33,7 +33,7 @@ void *smp_write_config_table(void *v, unsigned long * processor_map)
 	mc->mpe_checksum = 0;
 	mc->reserved = 0;
 
-	smp_write_processors(mc, processor_map);
+	smp_write_processors(mc);
 
 	{
 		device_t dev;
@@ -82,24 +82,25 @@ void *smp_write_config_table(void *v, unsigned long * processor_map)
 	smp_write_bus(mc, bus_isa, "ISA	  ");
 
 	/* IOAPIC handling */
-
 	smp_write_ioapic(mc, 2, 0x11, 0xfec00000);
 	{
 		device_t dev;
-		uint32_t base;
+		struct resource *res;
 		/* 8131 apic 3 */
 		dev = dev_find_slot(1, PCI_DEVFN(0x01,1));
 		if (dev) {
-			base = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
-			base &= PCI_BASE_ADDRESS_MEM_MASK;
-			smp_write_ioapic(mc, 0x03, 0x11, base);
+			res = find_resource(dev, PCI_BASE_ADDRESS_0);
+			if (res) {
+				smp_write_ioapic(mc, 0x03, 0x11, res->base);
+			}
 		}
 		/* 8131 apic 4 */
 		dev = dev_find_slot(1, PCI_DEVFN(0x02,1));
 		if (dev) {
-			base = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
-			base &= PCI_BASE_ADDRESS_MEM_MASK;
-			smp_write_ioapic(mc, 0x04, 0x11, base);
+			res = find_resource(dev, PCI_BASE_ADDRESS_0);
+			if (res) {
+				smp_write_ioapic(mc, 0x04, 0x11, res->base);
+			}
 		}
 	}
 
@@ -216,17 +217,16 @@ void *smp_write_config_table(void *v, unsigned long * processor_map)
 
 	/* Compute the checksums */
 	mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
-
 	mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
 	printk_debug("Wrote the mp table end at: %p - %p\n",
 		mc, smp_next_mpe_entry(mc));
 	return smp_next_mpe_entry(mc);
 }
 
-unsigned long write_smp_table(unsigned long addr, unsigned long *processor_map)
+unsigned long write_smp_table(unsigned long addr)
 {
 	void *v;
 	v = smp_write_floating_table(addr);
-	return (unsigned long)smp_write_config_table(v, processor_map);
+	return (unsigned long)smp_write_config_table(v);
 }