adapt config files

git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1701 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

2 files changed, 232 insertions, 158 deletions

diff --git a/src/mainboard/amd/quartet/Config.lb b/src/mainboard/amd/quartet/Config.lb
index bd7e11ceb0..c9a1d4203e 100644
--- a/src/mainboard/amd/quartet/Config.lb
+++ b/src/mainboard/amd/quartet/Config.lb
@@ -1,123 +1,3 @@
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HARD_RESET_BUS
-uses HARD_RESET_DEVICE
-uses HARD_RESET_FUNCTION
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
-uses CONFIG_MAX_CPUS
-uses CONFIG_IOAPIC
-uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
-uses CONFIG_ROM_STREAM
-uses CONFIG_ROM_STREAM_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-
-
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE=524288
-
-###
-### Build options
-###
-
-##
-## Build code for the fallback boot
-##
-default HAVE_FALLBACK_BOOT=1
-
-##
-## Build code to reset the motherboard from linuxBIOS
-##
-default HAVE_HARD_RESET=1
-
-default HARD_RESET_BUS=1
-default HARD_RESET_DEVICE=4
-default HARD_RESET_FUNCTION=0
-
-##
-## Build code to export a programmable irq routing table
-##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
-
-##
-## Build code to export an x86 MP table
-## Useful for specifying IRQ routing values
-##
-default HAVE_MP_TABLE=1
-
-##
-## Build code to export a CMOS option table
-##
-default HAVE_OPTION_TABLE=1
-
-##
-## Move the default LinuxBIOS cmos range off of AMD RTC registers
-##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
-
-##
-## Build code for SMP support
-## Only worry about 2 micro processors
-##
-default CONFIG_SMP=1
-default CONFIG_MAX_CPUS=4
-
-##
-## Build code to setup a generic IOAPIC
-##
-default CONFIG_IOAPIC=1
-
-##
-## Clean up the motherboard id strings
-##
-default MAINBOARD_PART_NUMBER="QUARTET"
-default MAINBOARD_VENDOR="AMD"
-
-###
-### LinuxBIOS layout values
-###
-
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
-default ROM_IMAGE_SIZE = 65536
-
-##
-## Use a small 8K stack
-##
-default STACK_SIZE=0x2000
-
-##
-## Use a small 16K heap
-##
-default HEAP_SIZE=0x4000
-
-##
-## Only use the option table in a normal image
-##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-
 ##
 ## Compute the location and size of where this firmware image
 ## (linuxBIOS plus bootloader) will live in the boot rom chip.
@@ -136,7 +16,6 @@ end
 ##
 default PAYLOAD_SIZE            = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
 default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
-default CONFIG_ROM_STREAM     = 1
 
 ##
 ## Compute where this copy of linuxBIOS will start in the boot rom
@@ -153,12 +32,7 @@ default _ROMBASE      = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE )
 default XIP_ROM_SIZE=65536
 default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
 
-##
-## Set all of the defaults for an x86 architecture
-##
-
-arch i386 end
-#cpu k8 end
+arch i386 end 
 
 ##
 ## Build the objects we have code for in this directory.
@@ -182,7 +56,7 @@ makerule ./failover.inc
 end
 
 makerule ./auto.E 
-	depends	"$(MAINBOARD)/auto.c option_table.h" 
+	depends	"$(MAINBOARD)/auto.c option_table.h"
 	action	"$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
 end
 makerule ./auto.inc 
@@ -193,21 +67,20 @@ end
 ##
 ## Build our 16 bit and 32 bit linuxBIOS entry code
 ##
-mainboardinit cpu/i386/entry16.inc
-mainboardinit cpu/i386/entry32.inc
-mainboardinit cpu/i386/bist32.inc
-ldscript /cpu/i386/entry16.lds
-ldscript /cpu/i386/entry32.lds
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
 
 ##
 ## Build our reset vector (This is where linuxBIOS is entered)
 ##
 if USE_FALLBACK_IMAGE 
-	mainboardinit cpu/i386/reset16.inc 
-	ldscript /cpu/i386/reset16.lds 
+	mainboardinit cpu/x86/16bit/reset16.inc
+	ldscript /cpu/x86/16bit/reset16.lds
 else
-	mainboardinit cpu/i386/reset32.inc 
-	ldscript /cpu/i386/reset32.lds 
+	mainboardinit cpu/x86/32bit/reset32.inc
+	ldscript /cpu/x86/32bit/reset32.lds
 end
 
 ### Should this be in the northbridge code?
@@ -219,11 +92,6 @@ mainboardinit arch/i386/lib/cpu_reset.inc
 mainboardinit arch/i386/lib/id.inc
 ldscript /arch/i386/lib/id.lds
 
-##
-## Setup our mtrrs
-##
-mainboardinit cpu/k8/earlymtrr.inc
-
 ###
 ### This is the early phase of linuxBIOS startup 
 ### Things are delicate and we test to see if we should
@@ -241,9 +109,12 @@ end
 ##
 ## Setup RAM
 ##
-mainboardinit cpu/k8/enable_mmx_sse.inc
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+mainboardinit cpu/x86/mmx/enable_mmx.inc
+mainboardinit cpu/x86/sse/enable_sse.inc
 mainboardinit ./auto.inc
-mainboardinit cpu/k8/disable_mmx_sse.inc
+mainboardinit cpu/x86/sse/disable_sse.inc
+mainboardinit cpu/x86/mmx/disable_mmx.inc
 
 ##
 ## Include the secondary Configuration files 
@@ -255,9 +126,9 @@ chip northbridge/amd/amdk8 # mc0
 	device pci_domain 0 on
 		device pci 18.0 on end
 		device pci 18.0 on end
-		device pci 18.0 
-			chip southbridge amd/amd8111
-				device pci 0:0.0 on 
+		device pci 18.0 on 
+			chip southbridge/amd/amd8111
+				device pci 0.0 on
 					device pci 0.0 on end
 					device pci 0.1 on end
 					device pci 0.2 on end
@@ -300,8 +171,8 @@ chip northbridge/amd/amdk8 # mc0
 				device pci 1.3 on end
 				device pci 1.5 on end
 				device pci 1.6 on end
-			end
-		end
+			end # 8111
+		end # device pci 18.0
 		device pci 18.1 on end
 		device pci 18.2 on end
 		device pci 18.3 on end
@@ -309,13 +180,13 @@ chip northbridge/amd/amdk8 # mc0
 		chip northbridge/amd/amdk8 # mc1
 			device pci 19.0 on end
 			device pci 19.0 on 
-				chip southbridge amd/amd8131 # amd8131_0
+				chip southbridge/amd/amd8131 # amd8131_0
 					device pci 0.0 on end
 					device pci 0.1 on end
 					device pci 1.0 on end
 					device pci 1.1 on end
 				end
-				chip southbridge amd/amd8131 # amd8131_1
+				chip southbridge/amd/amd8131 # amd8131_1
 					device pci 0.0 on end
 					device pci 0.1 on end
 					device pci 1.0 on end
@@ -362,10 +233,3 @@ chip northbridge/amd/amdk8 # mc0
 	end
 end
 
-##
-## Include the old serial code for those few places that still need it.
-##
-mainboardinit pc80/serial.inc
-mainboardinit arch/i386/lib/console.inc
-mainboardinit cpu/i386/bist32_fail.inc
-
diff --git a/src/mainboard/amd/quartet/Options.lb b/src/mainboard/amd/quartet/Options.lb
new file mode 100644
index 0000000000..77e54aa3aa
--- /dev/null
+++ b/src/mainboard/amd/quartet/Options.lb
@@ -0,0 +1,210 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses HARD_RESET_BUS
+uses HARD_RESET_DEVICE
+uses HARD_RESET_FUNCTION
+uses IRQ_SLOT_COUNT
+uses HAVE_OPTION_TABLE
+uses CONFIG_MAX_CPUS
+uses CONFIG_IOAPIC
+uses CONFIG_SMP
+uses FALLBACK_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM
+uses CONFIG_ROM_STREAM_START
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses USE_OPTION_TABLE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD_PART_NUMBER
+uses MAINBOARD_VENDOR
+uses MAINBOARD
+uses LINUXBIOS_EXTRA_VERSION
+uses _RAMBASE
+uses CC
+uses HOSTCC
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_CONSOLE_SERIAL8250
+
+
+###
+### Build options
+###
+
+##
+## ROM_SIZE is the size of boot ROM that this board will use.
+##
+default ROM_SIZE=524288
+
+##
+## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+##
+default FALLBACK_SIZE=131072
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=1
+
+##
+## Funky hard reset implementation
+## 
+default HARD_RESET_BUS=1
+default HARD_RESET_DEVICE=4
+default HARD_RESET_FUNCTION=0
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=9
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+default HAVE_MP_TABLE=1
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=1
+
+##
+## Move the default LinuxBIOS cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+##
+default CONFIG_SMP=1
+default CONFIG_MAX_CPUS=4
+
+##
+## Build code to setup a generic IOAPIC
+##
+default CONFIG_IOAPIC=1
+
+##
+## Clean up the motherboard id strings
+##
+default MAINBOARD_PART_NUMBER="QUARTET"
+default MAINBOARD_VENDOR="AMD"
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 65536
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+
+##
+## LinuxBIOS C code runs at this location in RAM
+##
+default _RAMBASE=0x00004000
+
+##
+## Load the payload from the ROM
+##
+default CONFIG_ROM_STREAM = 1
+
+###
+### Defaults of options that you may want to override in the target config file
+### 
+
+##
+## The default compiler
+##
+default CC="gcc -m32"
+default HOSTCC="gcc"
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG      1   system is unusable               
+## ALERT      2   action must be taken immediately 
+## CRIT       3   critical conditions              
+## ERR        4   error conditions                 
+## WARNING    5   warning conditions               
+## NOTICE     6   normal but significant condition 
+## INFO       7   informational                    
+## DEBUG      8   debug-level messages             
+## SPEW       9   Way too many details             
+
+## Request this level of debugging output
+default  DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+default  MAXIMUM_CONSOLE_LOGLEVEL=8
+
+##
+## Select power on after power fail setting
+default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+
+### End Options.lb
+end