diff options
author | Andrey Petrov <andrey.petrov@intel.com> | 2017-02-23 14:10:11 -0800 |
---|---|---|
committer | Andrey Petrov <andrey.petrov@intel.com> | 2017-02-25 09:00:50 +0100 |
commit | 6a489237d5686828f26d7e452824374df7fb5708 (patch) | |
tree | ca24b0c87fd7c18869cf4d1299e835b35bba998b /src/mainboard/intel/leafhill/devicetree.cb | |
parent | 37e30aa624e959bcc5b3a3a2ed1d1337c32afff4 (diff) | |
download | coreboot-6a489237d5686828f26d7e452824374df7fb5708.tar.xz |
mainboard/intel/leafhill: Clean up
This patch tries to clean the code by:
o removing duplication of LPC GPIO pads
o removing incorrect definitions from devicetree
o removing irrelevant entries from FMD file
Also adds vital defaults in Kconfig so it is possible to build an image.
Change-Id: Id9913f3b053189166392271152ce5300d82a7de8
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18479
Tested-by: build bot (Jenkins)
Diffstat (limited to 'src/mainboard/intel/leafhill/devicetree.cb')
-rw-r--r-- | src/mainboard/intel/leafhill/devicetree.cb | 259 |
1 files changed, 44 insertions, 215 deletions
diff --git a/src/mainboard/intel/leafhill/devicetree.cb b/src/mainboard/intel/leafhill/devicetree.cb index b0c82e2be8..2a284d2ee4 100644 --- a/src/mainboard/intel/leafhill/devicetree.cb +++ b/src/mainboard/intel/leafhill/devicetree.cb @@ -1,227 +1,56 @@ chip soc/intel/apollolake - device cpu_cluster 0 on - device lapic 0 on end - end - - register "pcie_rp0_clkreq_pin" = "0" # wifi/bt - # Disable unused clkreq of PCIe root ports + register "pcie_rp0_clkreq_pin" = "CLKREQ_DISABLED" register "pcie_rp1_clkreq_pin" = "CLKREQ_DISABLED" register "pcie_rp2_clkreq_pin" = "CLKREQ_DISABLED" register "pcie_rp3_clkreq_pin" = "CLKREQ_DISABLED" register "pcie_rp4_clkreq_pin" = "CLKREQ_DISABLED" register "pcie_rp5_clkreq_pin" = "CLKREQ_DISABLED" - # GPIO for PERST_0 - # If the Board has PERST_0 signal, assign the GPIO - # If the Board does not have PERST_0, assign GPIO_PRT0_UDEF - register "prt0_gpio" = "GPIO_122" - - # EMMC TX DATA Delay 1 - # Refer to EDS-Vol2-22.3. - # [14:8] steps of delay for HS400, each 125ps. - # [6:0] steps of delay for SDR104/HS200, each 125ps. - register "emmc_tx_data_cntl1" = "0x0C16" - - # EMMC TX DATA Delay 2 - # Refer to EDS-Vol2-22.3. - # [30:24] steps of delay for SDR50, each 125ps. - # [22:16] steps of delay for DDR50, each 125ps. - # [14:8] steps of delay for SDR25/HS50, each 125ps. - # [6:0] steps of delay for SDR12, each 125ps. - register "emmc_tx_data_cntl2" = "0x28162828" - - # EMMC RX CMD/DATA Delay 1 - # Refer to EDS-Vol2-22.3. - # [30:24] steps of delay for SDR50, each 125ps. - # [22:16] steps of delay for DDR50, each 125ps. - # [14:8] steps of delay for SDR25/HS50, each 125ps. - # [6:0] steps of delay for SDR12, each 125ps. - register "emmc_rx_cmd_data_cntl1" = "0x00181717" - - # EMMC RX CMD/DATA Delay 2 - # Refer to EDS-Vol2-22.3. - # [17:16] stands for Rx Clock before Output Buffer - # [14:8] steps of delay for Auto Tuning Mode, each 125ps. - # [6:0] steps of delay for HS200, each 125ps. - register "emmc_rx_cmd_data_cntl2" = "0x10008" - - # Enable DPTF - register "dptf_enable" = "1" - - # PL1 override 12000 mW: the energy calculation is wrong with the - # current VR solution. Experiments show that SoC TDP max (6W) can - # be reached when RAPL PL1 is set to 12W. - register "tdp_pl1_override_mw" = "12000" - # Set RAPL PL2 to 15W. - register "tdp_pl2_override_mw" = "15000" - - # Enable Audio Clock and Power gating - register "hdaudio_clk_gate_enable" = "1" - register "hdaudio_pwr_gate_enable" = "1" - register "hdaudio_bios_config_lockdown" = "1" - - # Enable lpss s0ix - register "lpss_s0ix_enable" = "1" - - # GPE configuration - # Note that GPE events called out in ASL code rely on this - # route, i.e., if this route changes then the affected GPE - # offset bits also need to be changed. This sets the PMC register - # GPE_CFG fields. - register "gpe0_dw1" = "PMC_GPE_N_31_0" - register "gpe0_dw2" = "PMC_GPE_N_63_32" - register "gpe0_dw3" = "PMC_GPE_SW_31_0" - - # Enable I2C0 for audio codec at 400kHz - register "i2c[0]" = "{ - .speed = I2C_SPEED_FAST, - .rise_time_ns = 104, - .fall_time_ns = 52, - }" - - # Enable I2C2 bus early for TPM at 400kHz - register "i2c[2]" = "{ - .early_init = 1, - .speed = I2C_SPEED_FAST, - .rise_time_ns = 57, - .fall_time_ns = 28, - }" - - # touchscreen at 400kHz - register "i2c[3]" = "{ - .speed = I2C_SPEED_FAST, - .rise_time_ns = 76, - .fall_time_ns = 164, - }" - - # trackpad at 400kHz - register "i2c[4]" = "{ - .speed = I2C_SPEED_FAST, - .rise_time_ns = 114, - .fall_time_ns = 164, - }" - - # digitizer at 400kHz - register "i2c[5]" = "{ - .speed = I2C_SPEED_FAST, - .rise_time_ns = 152, - .fall_time_ns = 30, - }" - - # Minimum SLP S3 assertion width 28ms. - register "slp_s3_assertion_width_usecs" = "28000" + device cpu_cluster 0 on + device lapic 0 on end + end device domain 0 on - device pci 00.0 on end # - Host Bridge - device pci 00.1 on end # - DPTF - device pci 00.2 on end # - NPK - device pci 02.0 on end # - Gen - device pci 03.0 on end # - Iunit - device pci 0d.0 on end # - P2SB - device pci 0d.1 on end # - PMC - device pci 0d.2 on end # - SPI - device pci 0d.3 on end # - Shared SRAM - device pci 0e.0 on # - Audio - chip drivers/generic/max98357a - register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_76)" - register "sdmode_delay" = "5" - device generic 0 on end - end - end - device pci 11.0 off end # - ISH - device pci 12.0 off end # - SATA - device pci 13.0 off end # - Root Port 2 - PCIe-A 0 - device pci 13.1 off end # - Root Port 3 - PCIe-A 1 - device pci 13.2 off end # - Root Port 4 - PCIe-A 2 - device pci 13.3 off end # - Root Port 5 - PCIe-A 3 - device pci 14.0 on - chip drivers/intel/wifi - register "wake" = "GPE0_DW3_00" - device pci 00.0 on end - end - end # - Root Port 0 - PCIe-B 0 - Wifi - device pci 14.1 off end # - Root Port 1 - PCIe-B 1 - device pci 15.0 on end # - XHCI - device pci 15.1 off end # - XDCI - device pci 16.0 on # - I2C 0 - chip drivers/i2c/da7219 - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_116_IRQ)" - register "btn_cfg" = "50" - register "mic_det_thr" = "500" - register "jack_ins_deb" = "20" - register "jack_det_rate" = ""32ms_64ms"" - register "jack_rem_deb" = "1" - register "a_d_btn_thr" = "0xa" - register "d_b_btn_thr" = "0x16" - register "b_c_btn_thr" = "0x21" - register "c_mic_btn_thr" = "0x3e" - register "btn_avg" = "4" - register "adc_1bit_rpt" = "1" - register "micbias_lvl" = "2600" - register "mic_amp_in_sel" = ""diff"" - device i2c 1a on end - end - end - device pci 16.1 on end # - I2C 1 - device pci 16.2 on - chip drivers/i2c/tpm - register "hid" = ""GOOG0005"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_28_IRQ)" - device i2c 50 on end - end - end # - I2C 2 - device pci 16.3 on - chip drivers/i2c/generic - register "hid" = ""ELAN0001"" - register "desc" = ""ELAN Touchscreen"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_21_IRQ)" - register "probed" = "1" - register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_36)" - register "reset_delay_ms" = "20" - register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_152)" - register "enable_delay_ms" = "1" - register "has_power_resource" = "1" - device i2c 10 on end - end - end # - I2C 3 - device pci 17.0 on - chip drivers/i2c/generic - register "hid" = ""ELAN0000"" - register "desc" = ""ELAN Touchpad"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_18_IRQ)" - register "wake" = "GPE0_DW1_15" - register "probed" = "1" - device i2c 15 on end - end - end # - I2C 4 - device pci 17.1 on - chip drivers/i2c/hid - register "generic.hid" = ""WCOM50C1"" - register "generic.desc" = ""WCOM Digitizer"" - register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_13_IRQ)" - register "hid_desc_reg_offset" = "0x1" - device i2c 0x9 on end - end - end # - I2C 5 - device pci 17.2 off end # - I2C 6 - device pci 17.3 off end # - I2C 7 - device pci 18.0 on end # - UART 0 - device pci 18.1 on end # - UART 1 - device pci 18.2 on end # - UART 2 - device pci 18.3 off end # - UART 3 - device pci 19.0 on end # - SPI 0 - device pci 19.1 off end # - SPI 1 - device pci 19.2 off end # - SPI 2 - device pci 1a.0 on end # - PWM - device pci 1b.0 on end # - SDCARD - device pci 1c.0 on end # - eMMC - device pci 1e.0 off end # - SDIO - device pci 1f.0 on # - LPC - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end - device pci 1f.1 on end # - SMBUS + device pci 00.0 on end # - Host Bridge + device pci 00.1 on end # - DPTF + device pci 00.2 on end # - NPK + device pci 02.0 on end # - Gen + device pci 03.0 on end # - Iunit + device pci 0d.0 on end # - P2SB + device pci 0d.1 on end # - PMC + device pci 0d.2 on end # - SPI + device pci 0d.3 on end # - Shared SRAM + device pci 0e.0 on end # - Audio + device pci 11.0 on end # - ISH + device pci 12.0 on end # - SATA + device pci 13.0 on end # - PCIe-A 0 + device pci 13.2 on end # - Onboard Lan + device pci 13.3 on end # - PCIe-A 3 + device pci 14.0 on end # - PCIe-B 0 + device pci 14.1 on end # - Onboard M2 Slot(Wifi/BT) + device pci 15.0 on end # - XHCI + device pci 15.1 on end # - XDCI + device pci 16.0 on end # - I2C 0 + device pci 16.1 on end # - I2C 1 + device pci 16.2 on end # - I2C 2 + device pci 16.3 on end # - I2C 3 + device pci 17.0 on end # - I2C 4 + device pci 17.1 on end # - I2C 5 + device pci 17.2 on end # - I2C 6 + device pci 17.3 on end # - I2C 7 + device pci 18.0 on end # - UART 0 + device pci 18.1 on end # - UART 1 + device pci 18.2 on end # - UART 2 + device pci 18.3 on end # - UART 3 + device pci 19.0 on end # - SPI 0 + device pci 19.1 on end # - SPI 1 + device pci 19.2 on end # - SPI 2 + device pci 1a.0 on end # - PWM + device pci 1b.0 on end # - SDCARD + device pci 1c.0 on end # - eMMC + device pci 1e.0 on end # - SDIO + device pci 1f.0 on end # - LPC + device pci 1f.1 on end # - SMBUS end end |