src/mainboard/lenovo-winent: Add space around operators

Change-Id: Iab2a879ebdea9d93ef5eb7e3abf875036c1e1cb4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16641
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>

12 files changed, 24 insertions, 24 deletions

diff --git a/src/mainboard/lippert/frontrunner-af/mainboard.c b/src/mainboard/lippert/frontrunner-af/mainboard.c
index 79c093fb81..a8cf5c5dea 100644
--- a/src/mainboard/lippert/frontrunner-af/mainboard.c
+++ b/src/mainboard/lippert/frontrunner-af/mainboard.c
@@ -31,7 +31,7 @@
 
 /* Init SIO GPIOs. */
 #define SIO_RUNTIME_BASE 0x0E00
-static const u16 sio_init_table[] = { // hi=offset, lo=value
+static const u16 sio_init_table[] = { // hi = offset, lo = value
 	0x4BA0, // GP1x: COM1/2 control   = RS232, no term, max 115200
 	0x2300, // GP10: COM1 termination = push/pull output
 	0x2400, // GP11: COM2 termination = push/pull output
@@ -70,7 +70,7 @@ static const u16 sio_init_table[] = { // hi=offset, lo=value
 static int smb_write_blk(u8 slave, u8 command, u8 length, const u8 *data)
 {
 	__outbyte(SMB0_STATUS, 0x1E);		// clear error status
-	__outbyte(SMB0_ADDRESS, slave & ~1);	// slave addr + direction=out
+	__outbyte(SMB0_ADDRESS, slave & ~1);	// slave addr + direction = out
 	__outbyte(SMB0_HOSTCMD, command);	// or destination offset
 	__outbyte(SMB0_DATA0, length);		// sent before data
 	__inbyte(SMB0_CONTROL);			// reset block data array
diff --git a/src/mainboard/lippert/frontrunner/irq_tables.c b/src/mainboard/lippert/frontrunner/irq_tables.c
index 2e0d9d624a..a8f7e364f7 100644
--- a/src/mainboard/lippert/frontrunner/irq_tables.c
+++ b/src/mainboard/lippert/frontrunner/irq_tables.c
@@ -23,7 +23,7 @@ static const struct irq_routing_table intel_irq_routing_table = {
 	PIRQ_VERSION,    /* u16 version   */
 	32+16*CONFIG_IRQ_SLOT_COUNT,	 /* there can be total CONFIG_IRQ_SLOT_COUNT devices on the bus */
 	0x00,		 /* Where the interrupt router lies (bus) */
-	(0x12<<3)|0x0,   /* Where the interrupt router lies (dev) */
+	(0x12 << 3)|0x0,   /* Where the interrupt router lies (dev) */
 	0x800,		 /* IRQs devoted exclusively to PCI usage */
 	0x1078,		 /* Vendor */
 	0x2,		 /* Device */
@@ -31,9 +31,9 @@ static const struct irq_routing_table intel_irq_routing_table = {
 	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
 	0xdf,         /*  u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
 	{
-		/* bus,     dev|fn,   {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap},  slot, rfu */
-		{0x00,(0x0e<<3)|0x0, {{0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x04, 0xdeb8}, {0x01, 0x0deb8}}, 0x1, 0x0},
-		{0x00,(0x0f<<3)|0x0, {{0x03, 0xdeb8}, {0x04, 0xdeb8}, {0x01, 0xdeb8}, {0x02, 0x0deb8}}, 0x2, 0x0},
+		/* bus,       dev|fn,   {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap},  slot, rfu */
+		{0x00,(0x0e << 3)|0x0, {{0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x04, 0xdeb8}, {0x01, 0x0deb8}}, 0x1, 0x0},
+		{0x00,(0x0f << 3)|0x0, {{0x03, 0xdeb8}, {0x04, 0xdeb8}, {0x01, 0xdeb8}, {0x02, 0x0deb8}}, 0x2, 0x0},
 	}
 };
 unsigned long write_pirq_routing_table(unsigned long addr)
diff --git a/src/mainboard/lippert/hurricane-lx/mainboard.c b/src/mainboard/lippert/hurricane-lx/mainboard.c
index ffd20d00cf..3d32113858 100644
--- a/src/mainboard/lippert/hurricane-lx/mainboard.c
+++ b/src/mainboard/lippert/hurricane-lx/mainboard.c
@@ -31,7 +31,7 @@
 	#define SIO_GP1X_CONFIG 0x00
 #endif
 
-static const u16 ec_init_table[] = { /* hi=data, lo=index */
+static const u16 ec_init_table[] = { /* hi = data, lo = index */
 	0x1900,		/* Enable monitoring */
 	0x0351,		/* TMPIN1,2 diode mode, TMPIN3 off */
 	0x805C,		/* Unlock zero adjust */
diff --git a/src/mainboard/lippert/hurricane-lx/romstage.c b/src/mainboard/lippert/hurricane-lx/romstage.c
index 0c9e03a4cd..7e3288f81e 100644
--- a/src/mainboard/lippert/hurricane-lx/romstage.c
+++ b/src/mainboard/lippert/hurricane-lx/romstage.c
@@ -76,7 +76,7 @@ static int smc_send_config(unsigned char config_data)
 #include "cpu/amd/geode_lx/syspreinit.c"
 #include "cpu/amd/geode_lx/msrinit.c"
 
-static const u16 sio_init_table[] = { // hi=data, lo=index
+static const u16 sio_init_table[] = { // hi = data, lo = index
 	0x042C,		// disable ATXPG; VIN6 enabled, FAN4/5 disabled, VIN7,VIN3 enabled
 	0x1423,		// don't delay PoWeROK1/2
 	0x9072,		// watchdog triggers PWROK, counts seconds
@@ -84,7 +84,7 @@ static const u16 sio_init_table[] = { // hi=data, lo=index
 	0x0073, 0x0074,	// disarm watchdog by changing 56 s timeout to 0
 #endif
 	0xBF25, 0x172A, 0xF326,	// select GPIO function for most pins
-	0xBF27, 0xFF28, 0x2D29,	// (GP36=FAN_CTL3 (PWM), GP23,22,16,15=SPI, GP13=PWROK1)
+	0xBF27, 0xFF28, 0x2D29,	// (GP36 = FAN_CTL3 (PWM), GP23,22,16,15 = SPI, GP13 = PWROK1)
 	0x66B8, 0x0CB9,	// enable pullups on SPI, RS485_EN
 	0x07C0,		// enable Simple-I/O for GP12-10= RS485_EN2,1, WD_ACTIVE
 	0x06C8,		// config GP12,11 as output, GP10 as input
diff --git a/src/mainboard/lippert/literunner-lx/mainboard.c b/src/mainboard/lippert/literunner-lx/mainboard.c
index 1a569e2b58..e4084b5cbc 100644
--- a/src/mainboard/lippert/literunner-lx/mainboard.c
+++ b/src/mainboard/lippert/literunner-lx/mainboard.c
@@ -34,7 +34,7 @@
 /* Bit0 enables COM3's transceiver, bit1 disables the RS485 receiver (e.g. for IR). */
 #define SIO_GP2X_CONFIG 0x00
 
-static const u16 ec_init_table[] = { /* hi=data, lo=index */
+static const u16 ec_init_table[] = { /* hi = data, lo = index */
 	0x1900,		/* Enable monitoring */
 	0x3050,		/* VIN4,5 enabled */
 	0x0351,		/* TMPIN1,2 diode mode, TMPIN3 off */
diff --git a/src/mainboard/lippert/literunner-lx/romstage.c b/src/mainboard/lippert/literunner-lx/romstage.c
index efe322c019..2f6aa469a0 100644
--- a/src/mainboard/lippert/literunner-lx/romstage.c
+++ b/src/mainboard/lippert/literunner-lx/romstage.c
@@ -115,7 +115,7 @@ static int smc_send_config(unsigned char config_data)
 #include "cpu/amd/geode_lx/syspreinit.c"
 #include "cpu/amd/geode_lx/msrinit.c"
 
-static const u16 sio_init_table[] = { // hi=data, lo=index
+static const u16 sio_init_table[] = { // hi = data, lo = index
 	0x072C,		// VIN6 enabled, FAN4/5 disabled, VIN7,VIN3 internal
 	0x1423,		// don't delay PoWeROK1/2
 	0x9072,		// watchdog triggers PWROK, counts seconds
@@ -123,7 +123,7 @@ static const u16 sio_init_table[] = { // hi=data, lo=index
 	0x0073, 0x0074,	// disarm watchdog by changing 56 s timeout to 0
 #endif
 	0xBF25, 0x172A, 0xF326,	// select GPIO function for most pins
-	0xFF27, 0xDF28, 0x2729,	// (GP45=SUSB, GP23,22,16,15=SPI, GP13=PWROK1)
+	0xFF27, 0xDF28, 0x2729,	// (GP45 = SUSB, GP23,22,16,15 = SPI, GP13 = PWROK1)
 	0x66B8, 0x0FB9,	// enable pullups on SPI, RS485_EN, COM3_R/TX_EN
 	0x07C0,		// enable Simple-I/O for GP12-10= RS485_EN2,1, LIVE_LED
 	0x03C1,		// enable Simple-I/O for GP21-20= COM3_RX_EN,TX_EN
@@ -131,7 +131,7 @@ static const u16 sio_init_table[] = { // hi=data, lo=index
 	0x07C8,		// config GP12-10 as output
 	0x03C9,		// config GP21-20 as output
 	0x2DF5,		// map Hw Monitor Thermal Output to GP55
-	0x08F8,		// map GP LED Blinking 1 to GP10=LIVE_LED (deactivate Simple I/O to use)
+	0x08F8,		// map GP LED Blinking 1 to GP10 = LIVE_LED (deactivate Simple I/O to use)
 };
 
 /* Early mainboard specific GPIO setup. */
diff --git a/src/mainboard/lippert/roadrunner-lx/mainboard.c b/src/mainboard/lippert/roadrunner-lx/mainboard.c
index cd83768598..1d35ebe464 100644
--- a/src/mainboard/lippert/roadrunner-lx/mainboard.c
+++ b/src/mainboard/lippert/roadrunner-lx/mainboard.c
@@ -31,7 +31,7 @@
 	#define SIO_GP1X_CONFIG 0x20
 #endif
 
-static const u16 ec_init_table[] = {	/* hi=data, lo=index */
+static const u16 ec_init_table[] = {	/* hi = data, lo = index */
 	0x1900,		/* Enable monitoring */
 	0x0351,		/* TMPIN1,2 diode mode, TMPIN3 off */
 	0x805C,		/* Unlock zero adjust */
diff --git a/src/mainboard/lippert/roadrunner-lx/romstage.c b/src/mainboard/lippert/roadrunner-lx/romstage.c
index d70e2c1835..7e0e2a5e01 100644
--- a/src/mainboard/lippert/roadrunner-lx/romstage.c
+++ b/src/mainboard/lippert/roadrunner-lx/romstage.c
@@ -52,7 +52,7 @@ int spd_read_byte(unsigned int device, unsigned int address)
 #include "cpu/amd/geode_lx/syspreinit.c"
 #include "cpu/amd/geode_lx/msrinit.c"
 
-static const u16 sio_init_table[] = {	// hi=data, lo=index
+static const u16 sio_init_table[] = {	// hi = data, lo = index
 	0x1E2C,		// disable ATXPG; VIN6,FAN4/5,VIN3 enabled, VIN7 internal
 	0x1423,		// don't delay PoWeROK1/2 - triggers 2nd reset
 	0x9072,		// watchdog triggers PWROK, counts seconds
@@ -60,13 +60,13 @@ static const u16 sio_init_table[] = {	// hi=data, lo=index
 	0x0073, 0x0074,	// disarm watchdog by changing 56 s timeout to 0
 #endif
 	0xBF25, 0x372A, 0xF326, // select GPIO function for most pins
-	0xBF27, 0xFF28, 0x2529, // (GP36=FAN_CTL3, GP13=PWROK1)
+	0xBF27, 0xFF28, 0x2529, // (GP36 = FAN_CTL3, GP13 = PWROK1)
 	0x46B8, 0x0CB9,	// enable pullups on RS485_EN
 	0x36C0,		// enable Simple-I/O for GP15,14,12,11= LIVE_LED, WD_ACTIVE, RS485_EN2,1
 	0xFFC3,		// enable Simple-I/O for GP47-40 (GPIOs on Supervisory Connector)
 	0x26C8,		// config GP15,12,11 as output; GP14 as input
 	0x2DF5,		// map Hw Monitor Thermal Output to GP55
-	0x0DF8,		// map GP LED Blinking 1 to GP15=LIVE_LED (deactivate Simple-I/O to use)
+	0x0DF8,		// map GP LED Blinking 1 to GP15 = LIVE_LED (deactivate Simple-I/O to use)
 };
 
 /* Early mainboard specific GPIO setup. */
diff --git a/src/mainboard/lippert/spacerunner-lx/devicetree.cb b/src/mainboard/lippert/spacerunner-lx/devicetree.cb
index 8619e84b6a..5f5b15bbb6 100644
--- a/src/mainboard/lippert/spacerunner-lx/devicetree.cb
+++ b/src/mainboard/lippert/spacerunner-lx/devicetree.cb
@@ -21,7 +21,7 @@ chip northbridge/amd/lx
 			register "com2_enable"				= "0"
 			register "com2_address"				= "0x2E8"
 			register "com2_irq"				= "6"
-			register "unwanted_vpci[0]"			= "0x80007B00" # Audio: 1<<31 + Device 0x0F<<11 + Function 3<<8
+			register "unwanted_vpci[0]"			= "0x80007B00" # Audio: 1 << 31 + Device 0x0F << 11 + Function 3 << 8
 			register "unwanted_vpci[1]"			= "0" # End of list has a zero
 			device pci 8.0 on end		# Slot4
 			device pci 9.0 on end		# Slot3
diff --git a/src/mainboard/lippert/spacerunner-lx/mainboard.c b/src/mainboard/lippert/spacerunner-lx/mainboard.c
index 4decd0e95e..b0bc74e9f6 100644
--- a/src/mainboard/lippert/spacerunner-lx/mainboard.c
+++ b/src/mainboard/lippert/spacerunner-lx/mainboard.c
@@ -31,7 +31,7 @@
 	#define SIO_GP1X_CONFIG 0x01
 #endif
 
-static const u16 ec_init_table[] = { /* hi=data, lo=index */
+static const u16 ec_init_table[] = { /* hi = data, lo = index */
 	0x1900,		/* Enable monitoring */
 	0x3050,		/* VIN4,5 enabled */
 	0x0351,		/* TMPIN1,2 diode mode, TMPIN3 off */
diff --git a/src/mainboard/lippert/spacerunner-lx/romstage.c b/src/mainboard/lippert/spacerunner-lx/romstage.c
index b3a13ad4b2..85503c547d 100644
--- a/src/mainboard/lippert/spacerunner-lx/romstage.c
+++ b/src/mainboard/lippert/spacerunner-lx/romstage.c
@@ -116,7 +116,7 @@ static int smc_send_config(unsigned char config_data)
 #include "cpu/amd/geode_lx/syspreinit.c"
 #include "cpu/amd/geode_lx/msrinit.c"
 
-static const u16 sio_init_table[] = { // hi=data, lo=index
+static const u16 sio_init_table[] = { // hi = data, lo = index
 	0x072C,		// VIN6 enabled, FAN4/5 disabled, VIN7,VIN3 internal
 	0x1423,		// don't delay PoWeROK1/2
 	0x9072,		// watchdog triggers PWROK, counts seconds
@@ -124,12 +124,12 @@ static const u16 sio_init_table[] = { // hi=data, lo=index
 	0x0073, 0x0074,	// disarm watchdog by changing 56 s timeout to 0
 #endif
 	0xBF25, 0x172A, 0xF326,	// select GPIO function for most pins
-	0xFF27, 0xDF28, 0x2729,	// (GP45=SUSB, GP23,22,16,15=SPI, GP13=PWROK1)
+	0xFF27, 0xDF28, 0x2729,	// (GP45 = SUSB, GP23,22,16,15 = SPI, GP13 = PWROK1)
 	0x66B8, 0x0CB9,	// enable pullups on SPI, RS485_EN
 	0x07C0,		// enable Simple-I/O for GP12-10= RS485_EN2,1, LIVE_LED
 	0x07C8,		// config GP12-10 as output
 	0x2DF5,		// map Hw Monitor Thermal Output to GP55
-	0x08F8,		// map GP LED Blinking 1 to GP10=LIVE_LED (deactivate Simple I/O to use)
+	0x08F8,		// map GP LED Blinking 1 to GP10 = LIVE_LED (deactivate Simple I/O to use)
 };
 
 /* Early mainboard specific GPIO setup. */
diff --git a/src/mainboard/lippert/toucan-af/mainboard.c b/src/mainboard/lippert/toucan-af/mainboard.c
index b9c532f4d8..6b51fd2e97 100644
--- a/src/mainboard/lippert/toucan-af/mainboard.c
+++ b/src/mainboard/lippert/toucan-af/mainboard.c
@@ -39,7 +39,7 @@
 static int smb_write_blk(u8 slave, u8 command, u8 length, const u8 *data)
 {
 	__outbyte(SMB0_STATUS, 0x1E);		// clear error status
-	__outbyte(SMB0_ADDRESS, slave & ~1);	// slave addr + direction=out
+	__outbyte(SMB0_ADDRESS, slave & ~1);	// slave addr + direction = out
 	__outbyte(SMB0_HOSTCMD, command);	// or destination offset
 	__outbyte(SMB0_DATA0, length);		// sent before data
 	__inbyte(SMB0_CONTROL);			// reset block data array
@@ -96,7 +96,7 @@ static void init(struct device *dev)
 	 * effect a power cycle and switch to the alternate BIOS chip.
 	 * Should be done as late as possible. */
 	printk(BIOS_INFO, "Sending BIOS alive message\n");
-	const u8 i_am_alive[] = { 0x03 }; //bit2=SEL_DP0: 0=DDI2, 1=LVDS
+	const u8 i_am_alive[] = { 0x03 }; //bit2 = SEL_DP0: 0 = DDI2, 1 = LVDS
 	if ((i = smb_write_blk(0x50, 0x25, sizeof(i_am_alive), i_am_alive)))
 		printk(BIOS_ERR, "smb_write_blk failed: %d\n", i);