eric patch

        1. x86_setup_mtrr take address bit.
        2. generic ht, pcix, pcie beidge...
        3. scan bus and reset_bus
        4. ht read ctrl to decide if the ht chain
           is ready
        5. Intel e7520 and e7525 support
        6. new ich5r support
        7. intel sb 6300 support.

yhlu patch
	1. split x86_setup_mtrrs to fixed and var
	2. if (resource->flags & IORESOURCE_FIXED ) return; in device.c pick_largest_resource
	3. in_conherent.c K8_SCAN_PCI_BUS


git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1982 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

1 files changed, 22 insertions, 20 deletions

diff --git a/src/mainboard/tyan/s2850/Options.lb b/src/mainboard/tyan/s2850/Options.lb
index c9b56b2811..646293e20e 100644
--- a/src/mainboard/tyan/s2850/Options.lb
+++ b/src/mainboard/tyan/s2850/Options.lb
@@ -3,9 +3,6 @@ uses HAVE_PIRQ_TABLE
 uses USE_FALLBACK_IMAGE
 uses HAVE_FALLBACK_BOOT
 uses HAVE_HARD_RESET
-uses HARD_RESET_BUS
-uses HARD_RESET_DEVICE
-uses HARD_RESET_FUNCTION
 uses IRQ_SLOT_COUNT
 uses HAVE_OPTION_TABLE
 uses CONFIG_MAX_CPUS
@@ -45,9 +42,9 @@ uses DEFAULT_CONSOLE_LOGLEVEL
 uses MAXIMUM_CONSOLE_LOGLEVEL
 uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
 uses CONFIG_CONSOLE_SERIAL8250
-uses CONFIG_CONSOLE_BTEXT
 uses HAVE_INIT_TIMER
 uses CONFIG_GDB_STUB
+uses CONFIG_GDB_STUB
 uses CROSS_COMPILE
 uses CC
 uses HOSTCC
@@ -57,6 +54,9 @@ uses CONFIG_CONSOLE_VGA
 uses CONFIG_PCI_ROM_RUN
 uses K8_E0_MEM_HOLE_SIZEK
 
+uses USE_DCACHE_RAM
+uses DCACHE_RAM_BASE
+uses DCACHE_RAM_SIZE
 uses CONFIG_USE_INIT
 
 ###
@@ -84,13 +84,6 @@ default HAVE_FALLBACK_BOOT=1
 default HAVE_HARD_RESET=1
 
 ##
-## Funky hard reset implementation
-## 
-default HARD_RESET_BUS=1
-default HARD_RESET_DEVICE=2
-default HARD_RESET_FUNCTION=0
-
-##
 ## Build code to export a programmable irq routing table
 ##
 default HAVE_PIRQ_TABLE=1
@@ -119,20 +112,29 @@ default LB_CKS_LOC=123
 ## Only worry about 2 micro processors
 ##
 default CONFIG_SMP=1
-default CONFIG_MAX_CPUS=1
+default CONFIG_MAX_CPUS=2
 default CONFIG_MAX_PHYSICAL_CPUS=1
-default CONFIG_LOGICAL_CPUS=0
+default CONFIG_LOGICAL_CPUS=1
+
+#CHIP_NAME ?
+default CONFIG_CHIP_NAME=1
 
 #1G memory hole
 default K8_E0_MEM_HOLE_SIZEK=0x100000
 
-#BTEXT CONSOLE
-#default CONFIG_CONSOLE_BTEXT=1
-
-#VGA
+#VGA Console
 default CONFIG_CONSOLE_VGA=1
 default CONFIG_PCI_ROM_RUN=1
 
+
+##
+## enable CACHE_AS_RAM specifics
+##
+default USE_DCACHE_RAM=1
+default DCACHE_RAM_BASE=0xcf000
+default DCACHE_RAM_SIZE=0x1000
+default CONFIG_USE_INIT=1
+
 ##
 ## Build code to setup a generic IOAPIC
 ##
@@ -141,7 +143,7 @@ default CONFIG_IOAPIC=1
 ##
 ## Clean up the motherboard id strings
 ##
-default MAINBOARD_PART_NUMBER="s2850"
+default MAINBOARD_PART_NUMBER="S2850"
 default MAINBOARD_VENDOR="Tyan"
 default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
 default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2850
@@ -231,9 +233,9 @@ default TTYS0_LCS=0x3
 ## SPEW       9   Way too many details             
 
 ## Request this level of debugging output
-default  DEFAULT_CONSOLE_LOGLEVEL=7
+default  DEFAULT_CONSOLE_LOGLEVEL=8
 ## At a maximum only compile in this level of debugging
-default  MAXIMUM_CONSOLE_LOGLEVEL=7
+default  MAXIMUM_CONSOLE_LOGLEVEL=8
 
 ##
 ## Select power on after power fail setting