newconfig is no more.

Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>


git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

1 files changed, 0 insertions, 245 deletions

diff --git a/src/mainboard/tyan/s2875/Options.lb b/src/mainboard/tyan/s2875/Options.lb
deleted file mode 100644
index 51913e30fb..0000000000
--- a/src/mainboard/tyan/s2875/Options.lb
+++ /dev/null
@@ -1,245 +0,0 @@
-uses CONFIG_GENERATE_MP_TABLE
-uses CONFIG_GENERATE_PIRQ_TABLE
-uses CONFIG_USE_FALLBACK_IMAGE
-uses CONFIG_HAVE_FALLBACK_BOOT
-uses CONFIG_HAVE_HARD_RESET
-uses CONFIG_IRQ_SLOT_COUNT
-uses CONFIG_HAVE_OPTION_TABLE
-uses CONFIG_MAX_CPUS
-uses CONFIG_MAX_PHYSICAL_CPUS
-uses CONFIG_LOGICAL_CPUS
-uses CONFIG_IOAPIC
-uses CONFIG_SMP
-uses CONFIG_FALLBACK_SIZE
-uses CONFIG_ROM_SIZE
-uses CONFIG_ROM_SECTION_SIZE
-uses CONFIG_ROM_IMAGE_SIZE
-uses CONFIG_ROM_SECTION_SIZE
-uses CONFIG_ROM_SECTION_OFFSET
-uses CONFIG_ROM_PAYLOAD
-uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses CONFIG_ROMBASE
-uses CONFIG_XIP_ROM_SIZE
-uses CONFIG_XIP_ROM_BASE
-uses CONFIG_STACK_SIZE
-uses CONFIG_HEAP_SIZE
-uses CONFIG_USE_OPTION_TABLE
-uses CONFIG_LB_CKS_RANGE_START
-uses CONFIG_LB_CKS_RANGE_END
-uses CONFIG_LB_CKS_LOC
-uses CONFIG_MAINBOARD_PART_NUMBER
-uses CONFIG_MAINBOARD_VENDOR
-uses CONFIG_MAINBOARD
-uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
-uses COREBOOT_EXTRA_VERSION
-uses CONFIG_RAMBASE
-uses CONFIG_TTYS0_BAUD
-uses CONFIG_TTYS0_BASE
-uses CONFIG_TTYS0_LCS
-uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
-uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
-uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-uses CONFIG_CONSOLE_SERIAL8250
-uses CONFIG_HAVE_INIT_TIMER
-uses CONFIG_GDB_STUB
-uses CONFIG_GDB_STUB
-uses CONFIG_CROSS_COMPILE
-uses CC
-uses HOSTCC
-uses CONFIG_OBJCOPY
-uses CONFIG_CONSOLE_VGA
-uses CONFIG_PCI_ROM_RUN
-uses CONFIG_HW_MEM_HOLE_SIZEK
-
-uses CONFIG_USE_DCACHE_RAM
-uses CONFIG_DCACHE_RAM_BASE
-uses CONFIG_DCACHE_RAM_SIZE
-uses CONFIG_USE_INIT
-uses CONFIG_USE_PRINTK_IN_CAR
-
-###
-### Build options
-###
-
-##
-## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
-##
-default CONFIG_ROM_SIZE=524288
-
-##
-## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
-##
-default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE
-
-
-##
-## Build code for the fallback boot
-##
-default CONFIG_HAVE_FALLBACK_BOOT=1
-
-##
-## Build code to reset the motherboard from coreboot
-##
-default CONFIG_HAVE_HARD_RESET=1
-
-##
-## Build code to export a programmable irq routing table
-##
-default CONFIG_GENERATE_PIRQ_TABLE=1
-default CONFIG_IRQ_SLOT_COUNT=13
-
-##
-## Build code to export an x86 MP table
-## Useful for specifying IRQ routing values
-##
-default CONFIG_GENERATE_MP_TABLE=1
-
-##
-## Build code to export a CMOS option table
-##
-default CONFIG_HAVE_OPTION_TABLE=1
-
-##
-## Move the default coreboot cmos range off of AMD RTC registers
-##
-default CONFIG_LB_CKS_RANGE_START=49
-default CONFIG_LB_CKS_RANGE_END=122
-default CONFIG_LB_CKS_LOC=123
-
-##
-## Build code for SMP support
-## Only worry about 2 micro processors
-##
-default CONFIG_SMP=1
-default CONFIG_MAX_CPUS=4
-default CONFIG_MAX_PHYSICAL_CPUS=2
-default CONFIG_LOGICAL_CPUS=1
-
-#1G memory hole
-default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
-
-#VGA Console
-default CONFIG_CONSOLE_VGA=1
-default CONFIG_PCI_ROM_RUN=1
-
-
-##
-## enable CACHE_AS_RAM specifics
-##
-default CONFIG_USE_DCACHE_RAM=1
-default CONFIG_DCACHE_RAM_BASE=0xcf000
-default CONFIG_DCACHE_RAM_SIZE=0x1000
-default CONFIG_USE_INIT=0
-
-##
-## Build code to setup a generic IOAPIC
-##
-default CONFIG_IOAPIC=1
-
-##
-## Clean up the motherboard id strings
-##
-default CONFIG_MAINBOARD_PART_NUMBER="s2875"
-default CONFIG_MAINBOARD_VENDOR="Tyan"
-default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x10f1
-default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2875
-
-###
-### coreboot layout values
-###
-
-## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default CONFIG_ROM_IMAGE_SIZE = 65536
-
-##
-## Use a small 8K stack
-##
-default CONFIG_STACK_SIZE=0x2000
-
-##
-## Use a small 16K heap
-##
-default CONFIG_HEAP_SIZE=0x4000
-
-##
-## Only use the option table in a normal image
-##
-default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE
-
-##
-## Coreboot C code runs at this location in RAM
-##
-default CONFIG_RAMBASE=0x00004000
-
-##
-## Load the payload from the ROM
-##
-default CONFIG_ROM_PAYLOAD = 1
-
-###
-### Defaults of options that you may want to override in the target config file
-### 
-
-##
-## The default compiler
-##
-default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
-
-##
-## Disable the gdb stub by default
-## 
-default CONFIG_GDB_STUB=0
-
-default CONFIG_USE_PRINTK_IN_CAR=1
-
-##
-## The Serial Console
-##
-
-# To Enable the Serial Console
-default CONFIG_CONSOLE_SERIAL8250=1
-
-## Select the serial console baud rate
-default CONFIG_TTYS0_BAUD=115200
-#default CONFIG_TTYS0_BAUD=57600
-#default CONFIG_TTYS0_BAUD=38400
-#default CONFIG_TTYS0_BAUD=19200
-#default CONFIG_TTYS0_BAUD=9600
-#default CONFIG_TTYS0_BAUD=4800
-#default CONFIG_TTYS0_BAUD=2400
-#default CONFIG_TTYS0_BAUD=1200
-
-# Select the serial console base port
-default CONFIG_TTYS0_BASE=0x3f8
-
-# Select the serial protocol
-# This defaults to 8 data bits, 1 stop bit, and no parity
-default CONFIG_TTYS0_LCS=0x3
-
-##
-### Select the coreboot loglevel
-##
-## EMERG      1   system is unusable               
-## ALERT      2   action must be taken immediately 
-## CRIT       3   critical conditions              
-## ERR        4   error conditions                 
-## WARNING    5   warning conditions               
-## NOTICE     6   normal but significant condition 
-## INFO       7   informational                    
-## CONFIG_DEBUG      8   debug-level messages             
-## SPEW       9   Way too many details             
-
-## Request this level of debugging output
-default  CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
-## At a maximum only compile in this level of debugging
-default  CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
-
-##
-## Select power on after power fail setting
-default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
-
-### End Options.lb
-end