summaryrefslogtreecommitdiff
path: root/src/soc/imgtec
diff options
context:
space:
mode:
authorIonela Voinescu <ionela.voinescu@imgtec.com>2014-09-09 20:18:55 +0100
committerPatrick Georgi <pgeorgi@google.com>2015-03-27 08:06:30 +0100
commit49aad6b387b3885f43d75aa50eceab50c6ac4aa9 (patch)
treec29f8507eb1d7be3d47bf66a1d135b766f93b5c0 /src/soc/imgtec
parent2d510d01d1eb45af0f8ba2b060748c465243c099 (diff)
downloadcoreboot-49aad6b387b3885f43d75aa50eceab50c6ac4aa9.tar.xz
soc/imgtec/pistachio: Add IMGTEC SPI controller driver
The Serial Peripheral Flash Interface (SPFI) block allows communication with various devices over the SPI bus. It uses a configurable transaction interface and it clocks the bus according to the configured command, address, gap (aka dummy) and data lengths. This controller requires the SPI_ATOMIC_SEQUENCING flag set (write and read done in the same transaction) as it cannot directly control CS and will assert/de-assert CS at the beginning/end of a transaction itself. Note that the size of any transfer cannot be greater than 64KB - 1, as this is configured in a 16-bit field. The SOC has 2 SPFI interfaces each of them providing 5 slave select lines. SPFI 0 supports single and dual modes, SPFI 1 supports single, dual and quad modes. For SPFI interface 0: - The block needs the system PLL and the following top level SPI clock registers to be set: - CR_cr_top_spi0clkinternal_CTRL[2:0] with division value - CR_MIPS_CLOCK_GATE[19]: bit cr_top_SPI0CLKOUT_MIPS set - CR_cr_top_SPI0CLKOUT_CTRL[6:0] with division value - The following MFIO configuration parameters are also required: Signal name Pad name MFIO mode spim0_d0_txd MFIO_MIPS_10 0 spim0_d1_rxd MFIO_MIPS_9 0 spim0_mclk MFIO_MIPS_8 0 spim0_cs0 MFIO_MIPS_2 1 spim0_cs1 MFIO_MIPS_1 1 spim0_cs2 MFIO_MIPS_55 1 MFIO_MIPS_28 1 spim0_cs3 MFIO_MIPS_56 1 MFIO_MIPS_29 1 spim0_cs4 MFIO_MIPS_57 1 MFIO_MIMPS_30 1 For SPFI interface 1: - The block needs the system PLL and the following top level SPI clock registers to be set: - CR_cr_top_spi1clkinternal_CTRL[2:0] with division value - CR_MIPS_CLOCK_GATE[20]: bit cr_top_SPI1CLKOUT_MIPS set - CR_cr_top_SPI1CLKOUT_CTRL[6:0] with division value - The following MFIO configuration parameters are also required: Signal name Pad name MFIO mode spim1_d0_txd MFIO_MIPS_5 0 spim1_d1_rxd MFIO_MIPS_4 0 spim1_mclk MFIO_MIPS_3 0 spim1_d2 MFIO_MIPS_6 0 spim1_d3 MFIO_MIPS_7 0 spim1_cs0 MFIO_MIPS_0 0 spim1_cs1 MFIO_MIPS_1 0 MFIO_MIPS_58 1 spim1_cs2 MFIO_MIPS_2 0 MFIO_MIPS_55 2 MFIO_MIPS_31 1 spim1_cs3 MFIO_MIPS_56 2 spim1_cs4 MFIO_MIPS_57 2 BUG=chrome-os-partner:31438, chrome-os-partner:32441 TEST=Tested as bare-metal driver on Pistachio FPGA Change-Id: I3b3e4475976e6fba58cef93b12d997ec5cb26341 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 621849942e27f7d6cf2c8ade7f2c4d18d2318b91 Original-Change-Id: Ib257eb6236bd2895281175871b4ab979660f1239 Original-Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com> Original-Reviewed-on: https://chromium-review.googlesource.com/217320 Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org> Reviewed-on: http://review.coreboot.org/9049 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Diffstat (limited to 'src/soc/imgtec')
-rw-r--r--src/soc/imgtec/pistachio/Kconfig1
-rw-r--r--src/soc/imgtec/pistachio/Makefile.inc1
-rw-r--r--src/soc/imgtec/pistachio/cpu.h24
-rw-r--r--src/soc/imgtec/pistachio/spi.c523
-rw-r--r--src/soc/imgtec/pistachio/spi.h358
5 files changed, 897 insertions, 10 deletions
diff --git a/src/soc/imgtec/pistachio/Kconfig b/src/soc/imgtec/pistachio/Kconfig
index 1acfe39a8c..83408bd8a1 100644
--- a/src/soc/imgtec/pistachio/Kconfig
+++ b/src/soc/imgtec/pistachio/Kconfig
@@ -26,6 +26,7 @@ config CPU_IMGTEC_PISTACHIO
select HAVE_MONOTONIC_TIMER
select HAVE_UART_MEMORY_MAPPED
select HAVE_UART_SPECIAL
+ select SPI_ATOMIC_SEQUENCING
bool
if CPU_IMGTEC_PISTACHIO
diff --git a/src/soc/imgtec/pistachio/Makefile.inc b/src/soc/imgtec/pistachio/Makefile.inc
index 1d5e0c2b16..e695abd5bb 100644
--- a/src/soc/imgtec/pistachio/Makefile.inc
+++ b/src/soc/imgtec/pistachio/Makefile.inc
@@ -39,6 +39,7 @@ ramstage-y += timestamp.c
romstage-y += cbmem.c
romstage-y += romstage.c
+romstage-y += monotonic_timer.c
romstage-y += timestamp.c
# Generate the actual coreboot bootblock code
diff --git a/src/soc/imgtec/pistachio/cpu.h b/src/soc/imgtec/pistachio/cpu.h
new file mode 100644
index 0000000000..c61c58dfca
--- /dev/null
+++ b/src/soc/imgtec/pistachio/cpu.h
@@ -0,0 +1,24 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2014 Imagination Technologies
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __SOC_IMGTEC_DANUBE_CPU_H__
+#define __SOC_IMGTEC_DANUBE_CPU_H__
+
+#define IMG_SPIM0_BASE_ADDRESS 0xB8100F00
+#define IMG_SPIM1_BASE_ADDRESS 0xB8101000
+
+#endif
diff --git a/src/soc/imgtec/pistachio/spi.c b/src/soc/imgtec/pistachio/spi.c
index 95bf8272a8..2b21475d0a 100644
--- a/src/soc/imgtec/pistachio/spi.c
+++ b/src/soc/imgtec/pistachio/spi.c
@@ -1,9 +1,11 @@
/*
- * Copyright (C) 2014 Google, Inc.
+ * This file is part of the coreboot project.
*
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
+ * Copyright (C) 2014 Imagination Technologies
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
@@ -11,25 +13,526 @@
* GNU General Public License for more details.
*/
-#include <stddef.h>
+#include <string.h>
+#include <stdlib.h>
+#include <timer.h>
#include <spi-generic.h>
+#include <spi_flash.h>
+#include "cpu.h"
+#include "spi.h"
+
+#if !CONFIG_SPI_ATOMIC_SEQUENCING
+#error "Unsupported SPI driver API"
+#endif
+
+struct img_spi_slave {
+ struct spi_slave slave;
+ /* SPIM instance device parameters */
+ struct spim_device_parameters device_parameters;
+ /* SPIM instance base address */
+ u32 base;
+ /* Boolean property that is TRUE if API has been initialised */
+ int initialised;
+};
+
+/* Allocate memory for the maximum number of devices */
+static struct
+img_spi_slave img_spi_slaves[SPIM_NUM_BLOCKS*SPIM_NUM_PORTS_PER_BLOCK];
+
+/*
+ * Wait for the bit at the shift position to be set in reg
+ * If the bit is not set in SPI_TIMEOUT_VALUE_US return with error
+ */
+static int wait_status(u32 reg, u32 shift)
+{
+ struct stopwatch sw;
+
+ stopwatch_init_usecs_expire(&sw, SPI_TIMEOUT_VALUE_US);
+ while (!(read32(reg) & (1 << shift))) {
+ if (stopwatch_expired(&sw))
+ return -SPIM_TIMEOUT;
+ }
+ return SPIM_OK;
+}
+
+/* Transmitter function. Fills TX FIFO with data before enabling SPIM */
+static int transmitdata(struct spi_slave *slave, u8 *buffer, u32 size)
+{
+ u32 blocksize, base, write_data;
+ int ret;
+
+ base = container_of(slave, struct img_spi_slave, slave)->base;
+ while (size) {
+ /* Wait until FIFO empty */
+ write32(base + SPFI_INT_CLEAR_REG_OFFSET, SPFI_SDE_MASK);
+ ret = wait_status(base + SPFI_INT_STATUS_REG_OFFSET,
+ SPFI_SDE_SHIFT);
+ if (ret)
+ return ret;
+
+ /*
+ * Write to FIFO in blocks of 16 words (64 bytes)
+ * Do 32bit writes first.
+ */
+ blocksize = SPIM_MAX_BLOCK_BYTES;
+ while ((size >= sizeof(u32)) && blocksize) {
+ memcpy(&write_data, buffer, sizeof(u32));
+ write32(base + SPFI_SEND_LONG_REG_OFFSET, write_data);
+ buffer += sizeof(u32);
+ size -= sizeof(u32);
+ blocksize -= sizeof(u32);
+ }
+ while (size && blocksize) {
+ write32(base + SPFI_SEND_BYTE_REG_OFFSET, *buffer);
+ buffer++;
+ size--;
+ blocksize--;
+ }
+ }
+ return SPIM_OK;
+}
+
+/* Receiver function */
+static int receivedata(struct spi_slave *slave, u8 *buffer, u32 size)
+{
+ u32 read_data, base;
+ int ret;
+
+ base = container_of(slave, struct img_spi_slave, slave)->base;
+ /*
+ * Do 32bit reads first. Clear status GDEX32BIT here so that the first
+ * status reg. read gets the actual bit state
+ */
+ write32(base + SPFI_INT_CLEAR_REG_OFFSET, SPFI_GDEX32BIT_MASK);
+ while (size >= sizeof(u32)) {
+ ret = wait_status(base + SPFI_INT_STATUS_REG_OFFSET,
+ SPFI_GDEX32BIT_SHIFT);
+ if (ret)
+ return ret;
+ read_data = read32(base + SPFI_GET_LONG_REG_OFFSET);
+ memcpy(buffer, &read_data, sizeof(u32));
+ buffer += sizeof(u32);
+ size -= sizeof(u32);
+ /* Clear interrupt status on GDEX32BITL */
+ write32(base + SPFI_INT_CLEAR_REG_OFFSET, SPFI_GDEX32BIT_MASK);
+ }
+
+ /*
+ * Do the remaining 8bit reads. Clear status GDEX8BIT here so that
+ * the first status reg. read gets the actual bit state
+ */
+ write32(base + SPFI_INT_CLEAR_REG_OFFSET, SPFI_GDEX8BIT_MASK);
+ while (size) {
+ ret = wait_status(base + SPFI_INT_STATUS_REG_OFFSET,
+ SPFI_GDEX8BIT_SHIFT);
+ if (ret)
+ return ret;
+ *buffer = read32(base + SPFI_GET_BYTE_REG_OFFSET);
+ buffer++;
+ size--;
+ /* Clear interrupt status on SPFI_GDEX8BIT */
+ write32(base + SPFI_INT_CLEAR_REG_OFFSET, SPFI_GDEX8BIT_MASK);
+ }
+ return SPIM_OK;
+}
+
+/* Sets port parameters in port state register. */
+static void setparams(struct spi_slave *slave, u32 port,
+ struct spim_device_parameters *params)
+{
+ u32 spim_parameters, port_state, base;
+
+ spim_parameters = 0;
+
+ base = container_of(slave, struct img_spi_slave, slave)->base;
+ port_state = read32(base + SPFI_PORT_STATE_REG_OFFSET);
+ port_state &= ~((SPIM_PORT0_MASK>>port)|SPFI_PORT_SELECT_MASK);
+ port_state |= params->cs_idle_level<<(SPIM_CS0_IDLE_SHIFT-port);
+ port_state |=
+ params->data_idle_level<<(SPIM_DATA0_IDLE_SHIFT-port);
+
+ /* Clock idle level and phase */
+ switch (params->spi_mode) {
+ case SPIM_MODE_0:
+ break;
+ case SPIM_MODE_1:
+ port_state |= (1 << (SPIM_CLOCK0_PHASE_SHIFT - port));
+ break;
+ case SPIM_MODE_2:
+ port_state |= (1 << (SPIM_CLOCK0_IDLE_SHIFT - port));
+ break;
+ case SPIM_MODE_3:
+ port_state |= (1 << (SPIM_CLOCK0_IDLE_SHIFT - port)) |
+ (1 << (SPIM_CLOCK0_PHASE_SHIFT - port));
+ break;
+ }
+ /* Set port state register */
+ write32(base + SPFI_PORT_STATE_REG_OFFSET, port_state);
+
+ /* Set up values to be written to device parameter register */
+ spim_parameters |= params->bitrate << SPIM_CLK_DIVIDE_SHIFT;
+ spim_parameters |= params->cs_setup << SPIM_CS_SETUP_SHIFT;
+ spim_parameters |= params->cs_hold << SPIM_CS_HOLD_SHIFT;
+ spim_parameters |= params->cs_delay << SPIM_CS_DELAY_SHIFT;
+
+ write32(base + SPFI_PORT_0_PARAM_REG_OFFSET + 4 * port,
+ spim_parameters);
+}
+
+/* Sets up transaction register */
+static u32 transaction_reg_setup(struct spim_buffer *first,
+ struct spim_buffer *second)
+{
+ u32 reg = 0;
+
+ /* 2nd transfer exists? */
+ if (second) {
+ /*
+ * If second transfer exists, it's a "command followed by data"
+ * type of transfer and first transfer is defined by
+ * CMD_LENGTH, ADDR_LENGTH, DUMMY_LENGTH... fields of
+ * transaction register
+ */
+ reg = spi_write_reg_field(reg, SPFI_CMD_LENGTH, 1);
+ reg = spi_write_reg_field(reg, SPFI_ADDR_LENGTH,
+ first->size - 1);
+ reg = spi_write_reg_field(reg, SPFI_DUMMY_LENGTH, 0);
+ /* Set data size (size of the second transfer) */
+ reg = spi_write_reg_field(reg, SPFI_TSIZE, second->size);
+ } else {
+ /* Set data size, in this case size of the 1st transfer */
+ reg = spi_write_reg_field(reg, SPFI_TSIZE, first->size);
+ }
+ return reg;
+}
+
+/* Sets up control register */
+static u32 control_reg_setup(struct spim_buffer *first,
+ struct spim_buffer *second)
+{
+ u32 reg;
+
+ /* Enable SPFI */
+ reg = SPFI_EN_MASK;
+ reg |= first->inter_byte_delay ? SPIM_BYTE_DELAY_MASK : 0;
+ /* Set up the transfer mode */
+ reg = spi_write_reg_field(reg, SPFI_TRNSFR_MODE_DQ, SPIM_CMD_MODE_0);
+ reg = spi_write_reg_field(reg, SPFI_TRNSFR_MODE, SPIM_DMODE_SINGLE);
+
+ if (second) {
+ /* Set TX bit if the 2nd transaction is 'send' */
+ reg = spi_write_reg_field(reg, SPFI_TX_RX,
+ second->isread ? 0 : 1);
+ /*
+ * Set send/get DMA for both transactions
+ * (first is always 'send')
+ */
+ reg = spi_write_reg_field(reg, SPIM_SEND_DMA, 1);
+ if (second->isread)
+ reg = spi_write_reg_field(reg, SPIM_GET_DMA, 1);
+
+ } else {
+ /* Set TX bit if the 1st transaction is 'send' */
+ reg |= first->isread ? 0 : SPFI_TX_RX_MASK;
+ /* Set send/get DMA */
+ reg |= first->isread ? SPIM_GET_DMA_MASK : SPIM_SEND_DMA_MASK;
+ }
+ return reg;
+}
+
+/* Checks the given buffer information */
+static int check_buffers(struct spi_slave *slave, struct spim_buffer *first,
+ struct spim_buffer *second){
+
+ if (!(container_of(slave, struct img_spi_slave, slave)->initialised))
+ return -SPIM_API_NOT_INITIALISED;
+ /*
+ * First operation must always be defined
+ * It can be either a read or a write and its size cannot be bigge
+ * than SPIM_MAX_TANSFER_BYTES = 64KB - 1 (0xFFFF)
+ */
+ if (!first)
+ return -SPIM_INVALID_READ_WRITE;
+ if (first->size > SPIM_MAX_TRANSFER_BYTES)
+ return -SPIM_INVALID_SIZE;
+ if (first->isread > 1)
+ return -SPIM_INVALID_READ_WRITE;
+ /* Check operation parameters for 'second' */
+ if (second) {
+ /*
+ * If the second operation is defined it must be a read
+ * operation and its size must not be bigger than
+ * SPIM_MAX_TANSFER_BYTES = 64KB - 1 (0xFFFF)
+ */
+ if (second->size > SPIM_MAX_TRANSFER_BYTES)
+ return -SPIM_INVALID_SIZE;
+ if (!second->isread)
+ return -SPIM_INVALID_READ_WRITE;
+ /*
+ * If the second operations is defined, the first operation
+ * must be a write and its size cannot be bigger than
+ * SPIM_MAX_FLASH_COMMAND_BYTES(8): command size (1) +
+ * address size (7).
+ */
+ if (first->isread)
+ return -SPIM_INVALID_READ_WRITE;
+ if (first->size > SPIM_MAX_FLASH_COMMAND_BYTES)
+ return -SPIM_INVALID_SIZE;
+
+ }
+ return SPIM_OK;
+}
+
+/* Checks the set bitrate */
+static int check_bitrate(u32 rate)
+{
+ /* Bitrate must be 1, 2, 4, 8, 16, 32, 64, or 128 */
+ switch (rate) {
+ case 1:
+ case 2:
+ case 4:
+ case 8:
+ case 16:
+ case 32:
+ case 64:
+ case 128:
+ return SPIM_OK;
+ default:
+ return -SPIM_INVALID_BIT_RATE;
+ }
+ return -SPIM_INVALID_BIT_RATE;
+}
+
+/* Checks device parameters for errors */
+static int check_device_params(struct spim_device_parameters *pdev_param)
+{
+ if (pdev_param->spi_mode < SPIM_MODE_0 ||
+ pdev_param->spi_mode > SPIM_MODE_3)
+ return -SPIM_INVALID_SPI_MODE;
+ if (check_bitrate(pdev_param->bitrate) != SPIM_OK)
+ return -SPIM_INVALID_BIT_RATE;
+ if (pdev_param->cs_idle_level > 1)
+ return -SPIM_INVALID_CS_IDLE_LEVEL;
+ if (pdev_param->data_idle_level > 1)
+ return -SPIM_INVALID_DATA_IDLE_LEVEL;
+ return SPIM_OK;
+}
+
+/* Function that carries out read/write operations */
+static int spim_io(struct spi_slave *slave, struct spim_buffer *first,
+ struct spim_buffer *second)
+{
+ u32 reg, base;
+ int i, trans_count, ret;
+ struct spim_buffer *transaction[2];
+
+ base = container_of(slave, struct img_spi_slave, slave)->base;
+
+ ret = check_buffers(slave, first, second);
+ if (ret)
+ return ret;
+
+ /*
+ * Soft reset peripheral internals, this will terminate any
+ * pending transactions
+ */
+ write32(base + SPFI_CONTROL_REG_OFFSET, SPIM_SOFT_RESET_MASK);
+ write32(base + SPFI_CONTROL_REG_OFFSET, 0);
+ /* Port state register */
+ reg = read32(base + SPFI_PORT_STATE_REG_OFFSET);
+ reg = spi_write_reg_field(reg, SPFI_PORT_SELECT, slave->cs);
+ write32(base + SPFI_PORT_STATE_REG_OFFSET, reg);
+ /* Set transaction register */
+ reg = transaction_reg_setup(first, second);
+ write32(base + SPFI_TRANSACTION_REG_OFFSET, reg);
+ /* Clear status */
+ write32(base + SPFI_INT_CLEAR_REG_OFFSET, 0xffffffff);
+ /* Set control register */
+ reg = control_reg_setup(first, second);
+ write32(base + SPFI_CONTROL_REG_OFFSET, reg);
+ /* First transaction always exists */
+ transaction[0] = first;
+ trans_count = 1;
+ /* Is there a second transaction? */
+ if (second) {
+ transaction[1] = second;
+ trans_count++;
+ }
+ /* Now write/read FIFO's */
+ for (i = 0; i < trans_count; i++)
+ /* Which transaction to execute, "Send" or "Get"? */
+ if (transaction[i]->isread) {
+ /* Get */
+ ret = receivedata(slave, transaction[i]->buffer,
+ transaction[i]->size);
+ if (ret) {
+ printk(BIOS_ERR,
+ "%s: Error: receive data failed.\n",
+ __func__);
+ return ret;
+ }
+ } else {
+ /* Send */
+ ret = transmitdata(slave, transaction[i]->buffer,
+ transaction[i]->size);
+ if (ret) {
+ printk(BIOS_ERR,
+ "%s: Error: transmit data failed.\n",
+ __func__);
+ return ret;
+ }
+ }
+
+ /* Wait for end of the transaction */
+ ret = wait_status(base + SPFI_INT_STATUS_REG_OFFSET,
+ SPFI_ALLDONE_SHIFT);
+ if (ret)
+ return ret;
+ /*
+ * Soft reset peripheral internals, this will terminate any
+ * pending transactions
+ */
+ write32(base + SPFI_CONTROL_REG_OFFSET, SPIM_SOFT_RESET_MASK);
+ write32(base + SPFI_CONTROL_REG_OFFSET, 0);
+
+ return SPIM_OK;
+}
+
+/* Initialization, must be called once on start up */
+void spi_init(void)
+{
+ /* Clear everything just in case */
+ memset(img_spi_slaves, 0, sizeof(img_spi_slaves));
+}
+
+/* Set up communications parameters for a SPI slave. */
struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs)
{
- return NULL;
+
+ struct img_spi_slave *img_slave = NULL;
+ struct spi_slave *slave;
+ struct spim_device_parameters *device_parameters;
+ u32 base;
+
+ switch (bus) {
+ case 0:
+ base = IMG_SPIM0_BASE_ADDRESS;
+ break;
+ case 1:
+ base = IMG_SPIM1_BASE_ADDRESS;
+ break;
+ default:
+ printk(BIOS_ERR, "%s: Error: unsupported bus.\n",
+ __func__);
+ return NULL;
+ }
+ if (cs > SPIM_DEVICE4) {
+ printk(BIOS_ERR, "%s: Error: unsupported chipselect.\n",
+ __func__);
+ return NULL;
+ }
+
+ img_slave = img_spi_slaves + bus * SPIM_NUM_PORTS_PER_BLOCK + cs;
+ slave = &(img_slave->slave);
+ device_parameters = &(img_slave->device_parameters);
+
+ img_slave->base = base;
+ slave->bus = bus;
+ slave->cs = cs;
+ slave->rw = SPI_READ_FLAG | SPI_WRITE_FLAG;
+ device_parameters->bitrate = 64;
+ device_parameters->cs_setup = 0;
+ device_parameters->cs_hold = 0;
+ device_parameters->cs_delay = 0;
+ device_parameters->spi_mode = SPIM_MODE_0;
+ device_parameters->cs_idle_level = 1;
+ device_parameters->data_idle_level = 0;
+ img_slave->initialised = IMG_FALSE;
+
+ return slave;
}
+/* Claim the bus and prepare it for communication */
int spi_claim_bus(struct spi_slave *slave)
{
- return 0;
+ int ret;
+ struct img_spi_slave *img_slave;
+
+ if (!slave) {
+ printk(BIOS_ERR, "%s: Error: slave was not set up.\n",
+ __func__);
+ return -SPIM_API_NOT_INITIALISED;
+ }
+ img_slave = container_of(slave, struct img_spi_slave, slave);
+ if (img_slave->initialised)
+ return SPIM_OK;
+ /* Check device parameters */
+ ret = check_device_params(&(img_slave->device_parameters));
+ if (ret) {
+ printk(BIOS_ERR, "%s: Error: incorrect device parameters.\n",
+ __func__);
+ return ret;
+ }
+ /* Set device parameters */
+ setparams(slave, slave->cs, &(img_slave->device_parameters));
+ /* Soft reset peripheral internals */
+ write32(img_slave->base + SPFI_CONTROL_REG_OFFSET,
+ SPIM_SOFT_RESET_MASK);
+ write32(img_slave->base + SPFI_CONTROL_REG_OFFSET, 0);
+ img_slave->initialised = IMG_TRUE;
+ return SPIM_OK;
}
+/* Release the SPI bus */
void spi_release_bus(struct spi_slave *slave)
{
+ struct img_spi_slave *img_slave;
+
+ if (!slave) {
+ printk(BIOS_ERR, "%s: Error: slave was not set up.\n",
+ __func__);
+ return;
+ }
+ img_slave = container_of(slave, struct img_spi_slave, slave);
+ img_slave->initialised = IMG_FALSE;
+ /* Soft reset peripheral internals */
+ write32(img_slave->base + SPFI_CONTROL_REG_OFFSET,
+ SPIM_SOFT_RESET_MASK);
+ write32(img_slave->base + SPFI_CONTROL_REG_OFFSET, 0);
}
-int spi_xfer(struct spi_slave *slave, const void *dout,
- unsigned out_bytes, void *din, unsigned in_bytes)
+/* SPI transfer */
+int spi_xfer(struct spi_slave *slave, const void *dout, unsigned int bytesout,
+ void *din, unsigned int bytesin)
{
- return 0;
+ struct spim_buffer buff_0;
+ struct spim_buffer buff_1;
+
+ if (!slave) {
+ printk(BIOS_ERR, "%s: Error: slave was not set up.\n",
+ __func__);
+ return -SPIM_API_NOT_INITIALISED;
+ }
+ if (!dout && !din) {
+ printk(BIOS_ERR, "%s: Error: both buffers are NULL.\n",
+ __func__);
+ return -SPIM_INVALID_TRANSFER_DESC;
+ }
+ /* If we only have a read or a write operation
+ * the parameters for it will be put in the first buffer
+ */
+ buff_0.buffer = (dout) ? (void *)dout : (void *)din;
+ buff_0.size = (dout) ? bytesout : bytesin;
+ buff_0.isread = (dout) ? IMG_FALSE : IMG_TRUE;
+ buff_0.inter_byte_delay = 0;
+
+ if (dout && din) {
+ /* Set up the read buffer to receive our data */
+ buff_1.buffer = din;
+ buff_1.size = bytesin;
+ buff_1.isread = IMG_TRUE;
+ buff_1.inter_byte_delay = 0;
+ }
+ return spim_io(slave, &buff_0, (dout && din) ? &buff_1 : NULL);
}
diff --git a/src/soc/imgtec/pistachio/spi.h b/src/soc/imgtec/pistachio/spi.h
new file mode 100644
index 0000000000..91d6d558e5
--- /dev/null
+++ b/src/soc/imgtec/pistachio/spi.h
@@ -0,0 +1,358 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2014 Imagination Technologies
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+
+#ifndef __SOC_IMGTEC_DANUBE_SPI_H__
+#define __SOC_IMGTEC_DANUBE_SPI_H__
+
+#include <arch/types.h>
+#include <arch/io.h>
+
+#define spi_read_reg_field(regval, field) \
+( \
+ ((field##_MASK) == 0xFFFFFFFF) ? \
+ (regval) : \
+ (((regval) & (field##_MASK)) >> (field##_SHIFT))\
+)
+
+#define spi_write_reg_field(regval, field, val) \
+( \
+ ((field##_MASK) == 0xFFFFFFFF) ? \
+ (val) : \
+ (((regval) & ~(field##_MASK)) | \
+ (((val) << (field##_SHIFT)) & (field##_MASK))) \
+)
+
+/*
+ * Parameter register
+ * Each of these corresponds to a single port (ie CS line) in the interface
+ * Fields Name Description
+ * ====== ==== ===========
+ * b31:24 CLK_RATE Bit Clock rate = (24.576 * value / 512) MHz
+ * b23:16 CS_SETUP Chip Select setup = (40 * value) ns
+ * b15:8 CS_HOLD Chip Select hold = (40 * value) ns
+ * b7:0 CS_DELAY Chip Select delay = (40 * value) ns
+ */
+
+#define SPIM_CLK_DIVIDE_MASK (0xFF000000)
+#define SPIM_CS_SETUP_MASK (0x00FF0000)
+#define SPIM_CS_HOLD_MASK (0x0000FF00)
+#define SPIM_CS_DELAY_MASK (0x000000FF)
+#define SPIM_CS_PARAM_MASK (SPIM_CS_SETUP_MASK \
+ | SPIM_CS_HOLD_MASK \
+ | SPIM_CS_DELAY_MASK)
+
+#define SPIM_CLK_DIVIDE_SHIFT (24)
+#define SPIM_CS_SETUP_SHIFT (16)
+#define SPIM_CS_HOLD_SHIFT (8)
+#define SPIM_CS_DELAY_SHIFT (0)
+#define SPIM_CS_PARAM_SHIFT (0)
+
+/* Control register */
+
+#define SPFI_DRIBBLE_COUNT_MASK (0x000e0000)
+#define SPFI_MEMORY_IF_MASK (0x00008000)
+#define SPIM_BYTE_DELAY_MASK (0x00004000)
+#define SPIM_CS_DEASSERT_MASK (0x00002000)
+#define SPIM_CONTINUE_MASK (0x00001000)
+#define SPIM_SOFT_RESET_MASK (0x00000800)
+#define SPIM_SEND_DMA_MASK (0x00000400)
+#define SPIM_GET_DMA_MASK (0x00000200)
+#define SPIM_EDGE_TX_RX_MASK (0x00000100)
+#define SPFI_TRNSFR_MODE_MASK (0x000000e0)
+#define SPFI_TRNSFR_MODE_DQ_MASK (0x0000001c)
+#define SPFI_TX_RX_MASK (0x00000002)
+#define SPFI_EN_MASK (0x00000001)
+
+#define SPFI_DRIBBLE_COUNT_SHIFT (17)
+#define SPFI_MEMORY_IF_SHIFT (15)
+#define SPIM_BYTE_DELAY_SHIFT (14)
+#define SPIM_CS_DEASSERT_SHIFT (13)
+#define SPIM_CONTINUE_SHIFT (12)
+#define SPIM_SOFT_RESET_SHIFT (11)
+#define SPIM_SEND_DMA_SHIFT (10)
+#define SPIM_GET_DMA_SHIFT (9)
+#define SPIM_EDGE_TX_RX_SHIFT (8)
+#define SPFI_TRNSFR_MODE_SHIFT (5)
+#define SPFI_TRNSFR_MODE_DQ_SHIFT (2)
+#define SPFI_TX_RX_SHIFT (1)
+#define SPFI_EN_SHIFT (0)
+
+/* Transaction register */
+
+#define SPFI_TSIZE_MASK (0xffff0000)
+#define SPFI_CMD_LENGTH_MASK (0x0000e000)
+#define SPFI_ADDR_LENGTH_MASK (0x00001c00)
+#define SPFI_DUMMY_LENGTH_MASK (0x000003e0)
+#define SPFI_PI_LENGTH_MASK (0x0000001c)
+
+#define SPFI_TSIZE_SHIFT (16)
+#define SPFI_CMD_LENGTH_SHIFT (13)
+#define SPFI_ADDR_LENGTH_SHIFT (10)
+#define SPFI_DUMMY_LENGTH_SHIFT (5)
+#define SPFI_PI_LENGTH_SHIFT (2)
+
+/* Port state register */
+
+#define SPFI_PORT_SELECT_MASK (0x00700000)
+/* WARNING the following bits are reversed */
+#define SPFI_CLOCK0_IDLE_MASK (0x000f8000)
+#define SPFI_CLOCK0_PHASE_MASK (0x00007c00)
+#define SPFI_CS0_IDLE_MASK (0x000003e0)
+#define SPFI_DATA0_IDLE_MASK (0x0000001f)
+
+#define SPIM_CLOCK0_IDLE_MASK (0x000f8000)
+#define SPIM_CLOCK0_PHASE_MASK (0x00007c00)
+#define SPIM_CS0_IDLE_MASK (0x000003e0)
+#define SPIM_DATA0_IDLE_MASK (0x0000001f)
+
+#define SPIM_PORT0_MASK (0x00084210)
+
+#define SPFI_PORT_SELECT_SHIFT (20)
+/* WARNING the following bits are reversed, bit 0 is highest */
+#define SPFI_CLOCK0_IDLE_SHIFT (19)
+#define SPFI_CLOCK0_PHASE_SHIFT (14)
+#define SPFI_CS0_IDLE_SHIFT (9)
+#define SPFI_DATA0_IDLE_SHIFT (4)
+
+#define SPIM_CLOCK0_IDLE_SHIFT (19)
+#define SPIM_CLOCK0_PHASE_SHIFT (14)
+#define SPIM_CS0_IDLE_SHIFT (9)
+#define SPIM_DATA0_IDLE_SHIFT (4)
+
+
+/*
+ * Interrupt registers
+ * SPFI_GDOF_MASK means Rx buffer full, not an overflow, because clock stalls
+ * SPFI_SDUF_MASK means Tx buffer empty, not an underflow, because clock stalls
+ */
+#define SPFI_IACCESS_MASK (0x00001000)
+#define SPFI_GDEX8BIT_MASK (0x00000800)
+#define SPFI_ALLDONE_MASK (0x00000200)
+#define SPFI_GDFUL_MASK (0x00000100)
+#define SPFI_GDHF_MASK (0x00000080)
+#define SPFI_GDEX32BIT_MASK (0x00000040)
+#define SPFI_GDTRIG_MASK (0x00000020)
+#define SPFI_SDFUL_MASK (0x00000008)
+#define SPFI_SDHF_MASK (0x00000004)
+#define SPFI_SDE_MASK (0x00000002)
+#define SPFI_SDTRIG_MASK (0x00000001)
+
+#define SPFI_IACCESS_SHIFT (12)
+#define SPFI_GDEX8BIT_SHIFT (11)
+#define SPFI_ALLDONE_SHIFT (9)
+#define SPFI_GDFUL_SHIFT (8)
+#define SPFI_GDHF_SHIFT (7)
+#define SPFI_GDEX32BIT_SHIFT (6)
+#define SPFI_GDTRIG_SHIFT (5)
+#define SPFI_SDFUL_SHIFT (3)
+#define SPFI_SDHF_SHIFT (2)
+#define SPFI_SDE_SHIFT (1)
+#define SPFI_SDTRIG_SHIFT (0)
+
+
+/* SPFI register block */
+
+#define SPFI_PORT_0_PARAM_REG_OFFSET (0x00)
+#define SPFI_PORT_1_PARAM_REG_OFFSET (0x04)
+#define SPFI_PORT_2_PARAM_REG_OFFSET (0x08)
+#define SPFI_PORT_3_PARAM_REG_OFFSET (0x0C)
+#define SPFI_PORT_4_PARAM_REG_OFFSET (0x10)
+#define SPFI_CONTROL_REG_OFFSET (0x14)
+#define SPFI_TRANSACTION_REG_OFFSET (0x18)
+#define SPFI_PORT_STATE_REG_OFFSET (0x1C)
+
+#define SPFI_SEND_LONG_REG_OFFSET (0x20)
+#define SPFI_SEND_BYTE_REG_OFFSET (0x24)
+#define SPFI_GET_LONG_REG_OFFSET (0x28)
+#define SPFI_GET_BYTE_REG_OFFSET (0x2C)
+
+#define SPFI_INT_STATUS_REG_OFFSET (0x30)
+#define SPFI_INT_ENABLE_REG_OFFSET (0x34)
+#define SPFI_INT_CLEAR_REG_OFFSET (0x38)
+
+#define SPFI_IMMEDIATE_STATUS_REG_OFFSET (0x3c)
+
+#define SPFI_FLASH_BASE_ADDRESS_REG_OFFSET (0x48)
+#define SPFI_FLASH_STATUS_REG_OFFSET (0x4C)
+
+#define IMG_FALSE 0
+#define IMG_TRUE 1
+
+/* Number of SPIM interfaces*/
+#define SPIM_NUM_BLOCKS 2
+/* Number of chip select lines supported by the SPI master port. */
+#define SPIM_NUM_PORTS_PER_BLOCK (SPIM_DUMMY_CS)
+/* Maximum transfer size (in bytes) for the SPI master port. */
+#define SPIM_MAX_TRANSFER_BYTES (0xFFFF)
+/* Maximum size of a flash command: command bytes+address_bytes. */
+#define SPIM_MAX_FLASH_COMMAND_BYTES (0x8)
+/* Write operation to fifo done in blocks of 16 words (64 bytes) */
+#define SPIM_MAX_BLOCK_BYTES (0x40)
+/* Number of tries until timeout error is returned*/
+#define SPI_TIMEOUT_VALUE_US 500000
+
+/* SPIM initialisation function return value.*/
+enum spim_return {
+ /* Initialisation parameters are valid. */
+ SPIM_OK = 0,
+ /* Mode parameter is invalid. */
+ SPIM_INVALID_SPI_MODE,
+ /* Chip select idle level is invalid. */
+ SPIM_INVALID_CS_IDLE_LEVEL,
+ /* Data idle level is invalid. */
+ SPIM_INVALID_DATA_IDLE_LEVEL,
+ /* Chip select line parameter is invalid. */
+ SPIM_INVALID_CS_LINE,
+ /* Transfer size parameter is invalid. */
+ SPIM_INVALID_SIZE,
+ /* Read/write parameter is invalid. */
+ SPIM_INVALID_READ_WRITE,
+ /* Continue parameter is invalid. */
+ SPIM_INVALID_CONTINUE,
+ /* Invalid block index */
+ SPIM_INVALID_BLOCK_INDEX,
+ /* Extended error values */
+ /* Invalid bit rate */
+ SPIM_INVALID_BIT_RATE,
+ /* Invalid CS hold value */
+ SPIM_INVALID_CS_HOLD_VALUE,
+ /* API function called before API is initialised */
+ SPIM_API_NOT_INITIALISED,
+ /* SPI driver initialisation failed */
+ SPIM_DRIVER_INIT_ERROR,
+ /* Invalid transfer description */
+ SPIM_INVALID_TRANSFER_DESC,
+ /* Timeout */
+ SPIM_TIMEOUT
+
+};
+
+/* This type defines the SPI Mode.*/
+enum spim_mode {
+ /* Mode 0 (clock idle low, data valid on first clock transition). */
+ SPIM_MODE_0 = 0,
+ /* Mode 1 (clock idle low, data valid on second clock transition). */
+ SPIM_MODE_1,
+ /* Mode 2 (clock idle high, data valid on first clock transition). */
+ SPIM_MODE_2,
+ /* Mode 3 (clock idle high, data valid on second clock transition). */
+ SPIM_MODE_3
+
+};
+
+/* This type defines the SPIM device numbers (chip select lines). */
+enum spim_device {
+ /* Device 0 (CS0). */
+ SPIM_DEVICE0 = 0,
+ /* Device 1 (CS1). */
+ SPIM_DEVICE1,
+ /* Device 2 (CS2). */
+ SPIM_DEVICE2,
+ /* Device 3 (CS3). */
+ SPIM_DEVICE3,
+ /* Device 4 (CS4). */
+ SPIM_DEVICE4,
+ /* Dummy chip select. */
+ SPIM_DUMMY_CS
+
+};
+
+/* This structure defines communication parameters for a slave device */
+struct spim_device_parameters {
+ /* Bit rate value.*/
+ unsigned char bitrate;
+ /*
+ * Chip select set up time.
+ * Time taken between chip select going active and activity occurring
+ * on the clock, calculated by dividing the desired set up time in ns
+ * by the Input clock period. (setup time / Input clock freq)
+ */
+ unsigned char cs_setup;
+ /*
+ * Chip select hold time.
+ * Time after the last clock pulse before chip select goes inactive,
+ * calculated by dividing the desired hold time in ns by the
+ * Input clock period (hold time / Input clock freq).
+ */
+ unsigned char cs_hold;
+ /*
+ * Chip select delay time (CS minimum inactive time).
+ * Minimum time after chip select goes inactive before chip select
+ * can go active again, calculated by dividing the desired delay time
+ * in ns by the Input clock period (delay time / Input clock freq).
+ */
+ unsigned char cs_delay;
+ /* SPI Mode. */
+ enum spim_mode spi_mode;
+ /* Chip select idle level (0=low, 1=high, Others=invalid). */
+ unsigned int cs_idle_level;
+ /* Data idle level (0=low, 1=high, Others=invalid). */
+ unsigned int data_idle_level;
+
+};
+
+/* Command transfer mode */
+enum command_mode {
+ /* Command, address, dummy and PI cycles are transferred on sio0 */
+ SPIM_CMD_MODE_0 = 0,
+ /*
+ * Command and Address are transferred on sio0 port only but dummy
+ * cycles and PI is transferred on all the interface ports.
+ */
+ SPIM_CMD_MODE_1,
+ /*
+ * Command is transferred on sio0 port only but address, dummy
+ * and PI is transferred on all the interface portS
+ */
+ SPIM_CMD_MODE_2,
+ /*
+ * Command, address, dummy and PI bytes are transferred on all
+ * the interfaces
+ */
+ SPIM_CMD_MODE_3
+};
+
+/* Data transfer mode */
+enum transfer_mode {
+ /* Transfer data in single mode */
+ SPIM_DMODE_SINGLE = 0,
+ /* Transfer data in dual mode */
+ SPIM_DMODE_DUAL,
+ /* Transfer data in quad mode */
+ SPIM_DMODE_QUAD
+};
+
+/* This structure contains parameters that describe an SPIM operation. */
+struct spim_buffer {
+ /* The buffer to read from or write to. */
+ unsigned char *buffer;
+
+ /* Number of bytes to read/write. Valid range is 0 to 65536 bytes. */
+ unsigned int size;
+
+ /* Read/write select. TRUE for read, FALSE for write, Others-invalid.*/
+ int isread;
+
+ /*
+ * ByteDelay select.
+ * Selects whether or not a delay is inserted between bytes.
+ * 0 - Minimum inter-byte delay
+ * 1 - Inter-byte delay of (cs_hold/master_clk half period)*master_clk.
+ */
+ int inter_byte_delay;
+};
+
+#endif /* __SOC_IMGTEC_DANUBE_SPI_H__ */