Trivial. Spelling check.

Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Zheng Bao <zheng.bao@amd.com>


git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5930 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

6 files changed, 11 insertions, 11 deletions

diff --git a/src/southbridge/amd/sb700/sb700_early_setup.c b/src/southbridge/amd/sb700/sb700_early_setup.c
index d667143ded..8c268d60af 100644
--- a/src/southbridge/amd/sb700/sb700_early_setup.c
+++ b/src/southbridge/amd/sb700/sb700_early_setup.c
@@ -63,7 +63,7 @@ static u8 set_sb700_revision(void)
 			rev = 0x11;	/* A11 */
 		else if (enable_14Mhz == 0x1) {
 			/* This happens, if does, only once. So later if we need to get
-			 * the rivision ID, we don't have to make such a big function.
+			 * the revision ID, we don't have to make such a big function.
 			 * We just get reg 0x8 in smbus dev. 0x39 is A11, 0x3A is A12. */
 			rev = 0x12;
 			byte = pci_read_config8(dev, 0x40);
@@ -549,7 +549,7 @@ static void sb700_pci_cfg(void)
 
 	/* LPC Device, BDF:0-20-3 */
 	/* The code below is ported from old chipset. It is not
-	 * metioned in RPR. But I keep them. The registers and the
+	 * mentioned in RPR. But I keep them. The registers and the
 	 * comments are compatible. */
 	dev = pci_locate_device(PCI_ID(0x1002, 0x439D), 0);
 	/* Enabling LPC DMA function. */
diff --git a/src/southbridge/amd/sb700/sb700_hda.c b/src/southbridge/amd/sb700/sb700_hda.c
index af1361692a..417d513e90 100644
--- a/src/southbridge/amd/sb700/sb700_hda.c
+++ b/src/southbridge/amd/sb700/sb700_hda.c
@@ -91,7 +91,7 @@ no_codec:
 }
 
 /**
- *  Wait 50usec for for the codec to indicate it is ready
+ *  Wait 50usec for the codec to indicate it is ready
  *  no response would imply that the codec is non-operative
  */
 static int wait_for_ready(u32 base)
@@ -112,7 +112,7 @@ static int wait_for_ready(u32 base)
 }
 
 /**
- *  Wait 50usec for for the codec to indicate that it accepted
+ *  Wait 50usec for the codec to indicate that it accepted
  *  the previous command.  No response would imply that the code
  *  is non-operative
  */
diff --git a/src/southbridge/amd/sb700/sb700_lpc.c b/src/southbridge/amd/sb700/sb700_lpc.c
index 14ed1b5418..f612a6a2df 100644
--- a/src/southbridge/amd/sb700/sb700_lpc.c
+++ b/src/southbridge/amd/sb700/sb700_lpc.c
@@ -108,7 +108,7 @@ static void sb700_lpc_set_resources(struct device *dev)
 /**
  * @brief Enable resources for children devices
  *
- * @param dev the device whos children's resources are to be enabled
+ * @param dev the device whose children's resources are to be enabled
  *
  */
 static void sb700_lpc_enable_childrens_resources(device_t dev)
diff --git a/src/southbridge/amd/sb700/sb700_sata.c b/src/southbridge/amd/sb700/sb700_sata.c
index 5c72a98a76..08b9aa8ad9 100644
--- a/src/southbridge/amd/sb700/sb700_sata.c
+++ b/src/southbridge/amd/sb700/sb700_sata.c
@@ -111,7 +111,7 @@ static void sata_init(struct device *dev)
 	/* get rev_id */
 	rev_id = pci_read_config8(sm_dev, 0x08) - 0x28;
 
-	/* get base addresss */
+	/* get base address */
 	sata_bar5 = pci_read_config32(dev, 0x24) & ~0x3FF;
 	sata_bar0 = pci_read_config16(dev, 0x10) & ~0x7;
 	sata_bar1 = pci_read_config16(dev, 0x14) & ~0x3;
diff --git a/src/southbridge/amd/sb700/sb700_sm.c b/src/southbridge/amd/sb700/sb700_sm.c
index 65ccce9199..b017a1452f 100644
--- a/src/southbridge/amd/sb700/sb700_sm.c
+++ b/src/southbridge/amd/sb700/sb700_sm.c
@@ -206,7 +206,7 @@ static void sm_init(device_t dev)
 	/* 4.14:Enabling Requester ID for upstream traffic. */
 	abcfg_reg(0x98, 1 << 16, 1 << 16);
 
-	/* 9.2: Enableing IDE Data Bus DD7 Pull Down Resistor */
+	/* 9.2: Enabling IDE Data Bus DD7 Pull Down Resistor */
 	byte = pm2_ioread(0xE5);
 	byte |= 1 << 2;
 	pm2_iowrite(0xE5, byte);
@@ -345,7 +345,7 @@ static void sb700_sm_set_resources(struct device *dev)
 
 	pci_dev_set_resources(dev);
 
-	/* rpr2.14: Make HPET MMIO decoding controlled by the memory enable bit in command register of LPC ISA bridage */
+	/* rpr2.14: Make HPET MMIO decoding controlled by the memory enable bit in command register of LPC ISA bridge */
 	byte = pm_ioread(0x52);
 	byte |= 1 << 6;
 	pm_iowrite(0x52, byte);
diff --git a/src/southbridge/amd/sb700/sb700_usb.c b/src/southbridge/amd/sb700/sb700_usb.c
index 8ee6e37ac9..3b3ad584a7 100644
--- a/src/southbridge/amd/sb700/sb700_usb.c
+++ b/src/southbridge/amd/sb700/sb700_usb.c
@@ -83,7 +83,7 @@ static void usb_init2(struct device *dev)
 	usb2_bar0 = pci_read_config32(dev, 0x10) & ~0xFF;
 	printk(BIOS_INFO, "usb2_bar0=0x%x\n", usb2_bar0);
 
-	/* RPR6.4 Enables the USB PHY auto calibration resister to match 45ohm resistence */
+	/* RPR6.4 Enables the USB PHY auto calibration resister to match 45ohm resistance */
 	dword = 0x00020F00;
 	write32(usb2_bar0 + 0xC0, dword);
 
@@ -105,8 +105,8 @@ static void usb_init2(struct device *dev)
 	pci_write_config32(dev, 0x50, dword);
 	#endif
 
-	/* RPR6.13 Enabling Fix for EHCI Controller Dirver Yellow Sign Issue */
-	/* RPR says it is just for A12. CIMM sets it when it is above A11. */
+	/* RPR6.13 Enabling Fix for EHCI Controller Driver Yellow Sign Issue */
+	/* RPR says it is just for A12. CIMx sets it when it is above A11. */
 	dword = pci_read_config32(dev, 0x50);
 	dword |= (1 << 20);
 	pci_write_config32(dev, 0x50, dword);