diff options
author | Uwe Hermann <uwe@hermann-uwe.de> | 2008-10-12 14:40:23 +0000 |
---|---|---|
committer | Uwe Hermann <uwe@hermann-uwe.de> | 2008-10-12 14:40:23 +0000 |
commit | 0a20c416226d34ef25881e4d143cf1b8bf531656 (patch) | |
tree | 4063219eef59254c34ef8db6fef59f3d2fc7e1c8 /src/southbridge/via/vt8237r | |
parent | 2e5a9d952f3f3d23cf57a08abeffe3dee3444950 (diff) | |
download | coreboot-0a20c416226d34ef25881e4d143cf1b8bf531656.tar.xz |
VIA VT8237R cleanups (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3651 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Diffstat (limited to 'src/southbridge/via/vt8237r')
-rw-r--r-- | src/southbridge/via/vt8237r/chip.h | 2 | ||||
-rw-r--r-- | src/southbridge/via/vt8237r/vt8237_ctrl.c | 69 | ||||
-rw-r--r-- | src/southbridge/via/vt8237r/vt8237r.c | 3 | ||||
-rw-r--r-- | src/southbridge/via/vt8237r/vt8237r_early_smbus.c | 205 | ||||
-rw-r--r-- | src/southbridge/via/vt8237r/vt8237r_lpc.c | 72 | ||||
-rw-r--r-- | src/southbridge/via/vt8237r/vt8237r_sata.c | 34 |
6 files changed, 205 insertions, 180 deletions
diff --git a/src/southbridge/via/vt8237r/chip.h b/src/southbridge/via/vt8237r/chip.h index 8f15c1ae94..f853ff26d3 100644 --- a/src/southbridge/via/vt8237r/chip.h +++ b/src/southbridge/via/vt8237r/chip.h @@ -53,7 +53,7 @@ struct southbridge_via_vt8237r_config { int ide0_enable:1; int ide1_enable:1; - /* 1 = 80-pin cable */ + /* 1 = 80-pin cable, 0 = 40-pin cable */ int ide0_80pin_cable:1; int ide1_80pin_cable:1; }; diff --git a/src/southbridge/via/vt8237r/vt8237_ctrl.c b/src/southbridge/via/vt8237r/vt8237_ctrl.c index 666fbcf68c..0af20d37cb 100644 --- a/src/southbridge/via/vt8237r/vt8237_ctrl.c +++ b/src/southbridge/via/vt8237r/vt8237_ctrl.c @@ -28,20 +28,17 @@ static void vt8237_cfg(struct device *dev) { u8 regm, regm2, regm3; - device_t devfun3; devfun3 = dev_find_device(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_K8T890CE_3, 0); - - if (!devfun3) - devfun3 = dev_find_device(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_K8M890CE_3, 0); - - if (!devfun3) - die("Unknown NB"); - - /* CPU to PCI Flow Control 1 & 2, just fill in recommended */ + PCI_DEVICE_ID_VIA_K8T890CE_3, 0); + if (!devfun3) + devfun3 = dev_find_device(PCI_VENDOR_ID_VIA, + PCI_DEVICE_ID_VIA_K8M890CE_3, 0); + if (!devfun3) + die("Unknown NB"); + + /* CPU to PCI Flow Control 1 & 2, just fill in recommended. */ pci_write_config8(dev, 0x70, 0xc2); pci_write_config8(dev, 0x71, 0xc8); @@ -54,7 +51,8 @@ static void vt8237_cfg(struct device *dev) pci_write_config8(dev, 0x77, 0x48); pci_write_config8(dev, 0x78, 0x01); /* APIC on HT */ - pci_write_config8(dev, 0x7c, 0x77); //maybe Enable LDT APIC Mode bit3 set to 1 + /* Maybe Enable LDT APIC Mode bit3 set to 1 */ + pci_write_config8(dev, 0x7c, 0x77); /* WARNING: Need to copy some registers from NB (D0F3) to SB (D11F7). */ @@ -89,28 +87,24 @@ static void vt8237_cfg(struct device *dev) * NB V-Link Manual Driving Control - Data 0xb6 0x46 0x46 0x88 0x88 * NB V-Link Receiving Strobe Delay 0xb7 0x02 0x02 0x61 0x01 * NB V-Link Compensation Control bit4,0 (b5,b6) 0xb4 0x10 0x10 0x11 0x11 - * SB V-Link Strobe Drive Control 0xb9 0x00 0xa5 0x98 0x98 + * SB V-Link Strobe Drive Control 0xb9 0x00 0xa5 0x98 0x98 * SB V-Link Data drive Control???? 0xba 0x00 0xbb 0x77 0x77 * SB V-Link Receive Strobe Delay???? 0xbb 0x04 0x11 0x11 0x11 * SB V-Link Compensation Control bit0 (use b9) 0xb8 0x00 0x01 0x01 0x01 * V-Link CKG Control 0xb0 0x05 0x05 0x06 0x03 * V-Link CKG Control 0xb1 0x05 0x05 0x01 0x03 */ - static void vt8237s_vlink_init(struct device *dev) { u8 reg; - device_t devfun7; devfun7 = dev_find_device(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_K8T890CE_7, 0); - + PCI_DEVICE_ID_VIA_K8T890CE_7, 0); if (!devfun7) devfun7 = dev_find_device(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_K8M890CE_7, 0); - - /* no pairing NB found */ + PCI_DEVICE_ID_VIA_K8M890CE_7, 0); + /* No pairing NB was found. */ if (!devfun7) return; @@ -132,40 +126,43 @@ static void vt8237s_vlink_init(struct device *dev) pci_write_config8(dev, 0xba, 0x88); pci_write_config8(dev, 0xbb, 0x89); - reg = pci_read_config8(dev, 0xbd); reg |= 0x3; pci_write_config8(dev, 0xbd, reg); - /* Program V-link 8X 8bit full duplex, parity disabled FIXME */ + /* Program V-link 8X 8bit full duplex, parity disabled. FIXME. */ pci_write_config8(dev, 0x48, 0x13); } -static void ctrl_enable(struct device *dev) { - - /* enable the 0:13 and 0:13.1 */ +static void ctrl_enable(struct device *dev) +{ + /* Enable the 0:13 and 0:13.1. */ /* FIXME */ pci_write_config8(dev, 0x4f, 0x43); } - extern void dump_south(device_t dev); -static void ctrl_init(struct device *dev) { - - /* TODO: Fix some ordering issue fo V-link set Rx77[6] and PCI1_Rx4F[0] - should to 1 FIXME DO you need?*/ +static void ctrl_init(struct device *dev) +{ + /* + * TODO: Fix some ordering issue for V-link set Rx77[6] and + * PCI1_Rx4F[0] should to 1. + * FIXME DO you need? + */ - /* VT8237R specific configuration other SB are done in their own directories */ - /* add A version */ + /* + * VT8237R specific configuration. Other SB are done in their own + * directories. TODO: Add A version. + */ device_t devsb = dev_find_device(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_VT8237S_LPC, 0); + PCI_DEVICE_ID_VIA_VT8237S_LPC, 0); if (devsb) { - /* FIXME: Skip v-link setup for now */ -// vt8237s_vlink_init(dev); + /* FIXME: Skip v-link setup for now. */ +// vt8237s_vlink_init(dev); } - /* configure PCI1 and copy mirror registers from D0F3 */ + /* Configure PCI1 and copy mirror registers from D0F3. */ vt8237_cfg(dev); dump_south(dev); } diff --git a/src/southbridge/via/vt8237r/vt8237r.c b/src/southbridge/via/vt8237r/vt8237r.c index a72b9a1c06..4ec49cd1c8 100644 --- a/src/southbridge/via/vt8237r/vt8237r.c +++ b/src/southbridge/via/vt8237r/vt8237r.c @@ -63,9 +63,8 @@ void dump_south(device_t dev) for (i = 0; i < 256; i += 16) { printk_debug("%02x: ", i); - for (j = 0; j < 16; j++) { + for (j = 0; j < 16; j++) printk_debug("%02x ", pci_read_config8(dev, i + j)); - } printk_debug("\n"); } } diff --git a/src/southbridge/via/vt8237r/vt8237r_early_smbus.c b/src/southbridge/via/vt8237r/vt8237r_early_smbus.c index 5b865d3814..9c91a71963 100644 --- a/src/southbridge/via/vt8237r/vt8237r_early_smbus.c +++ b/src/southbridge/via/vt8237r/vt8237r_early_smbus.c @@ -128,27 +128,27 @@ u8 smbus_read_byte(u8 dimm, u8 offset) return val; } + /** - * Enable the smbus on vt8237r-based systems + * Enable the SMBus on VT8237R-based systems. */ void enable_smbus(void) { device_t dev; /* Power management controller */ - dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT8237R_LPC), 0); - if (dev == PCI_DEV_INVALID) { /* Power management controller */ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_VT8237S_LPC), 0); + PCI_DEVICE_ID_VIA_VT8237S_LPC), 0); if (dev == PCI_DEV_INVALID) die("Power management controller not found\r\n"); } - /* 7 = SMBus Clock from RTC 32.768KHz + /* + * 7 = SMBus Clock from RTC 32.768KHz * 5 = Internal PLL reset from susp */ pci_write_config8(dev, VT8237R_POWER_WELL, 0xa0); @@ -201,7 +201,7 @@ void smbus_fixup(const struct mem_controller *ctrl) * VT8237R has only been seen on DDR and DDR2 based systems, so far. */ for (i = 0; (i < SMBUS_TIMEOUT && ((result < SPD_MEMORY_TYPE_SDRAM) || - (result > SPD_MEMORY_TYPE_SDRAM_DDR3))); i++) { + (result > SPD_MEMORY_TYPE_SDRAM_DDR3))); i++) { if (current_slot > ram_slots) current_slot = 0; @@ -218,88 +218,100 @@ void smbus_fixup(const struct mem_controller *ctrl) PRINT_DEBUG("Done\r\n"); } -/* fixme better separate the NB and SB, will done once it works */ +/* FIXME: Better separate the NB and SB, will be done once it works. */ -void vt8237_sb_enable_fid_vid(void) { - device_t dev; - device_t devctl; +void vt8237_sb_enable_fid_vid(void) +{ + device_t dev, devctl; /* Power management controller */ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT8237R_LPC), 0); - if (dev == PCI_DEV_INVALID) { - /* Power management controller */ + /* Power management controller */ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_VT8237S_LPC), 0); + PCI_DEVICE_ID_VIA_VT8237S_LPC), 0); if (dev == PCI_DEV_INVALID) return; devctl = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_VT8237_VLINK), 0); + PCI_DEVICE_ID_VIA_VT8237_VLINK), 0); if (devctl == PCI_DEV_INVALID) return; - + + /* TODO: Why is this an extra block? */ { - u8 tmp; - tmp = pci_read_config8(devctl, 0xec); - print_debug("EC is "); - print_debug_hex8(tmp); - print_debug(" E5 is "); - tmp = pci_read_config8(dev, 0xe5); - print_debug_hex8(tmp); - + u8 tmp; + tmp = pci_read_config8(devctl, 0xec); + print_debug("EC is "); + print_debug_hex8(tmp); + print_debug(" E5 is "); + tmp = pci_read_config8(dev, 0xe5); + print_debug_hex8(tmp); } + /* Set ACPI base address to I/O VT8237R_ACPI_IO_BASE. */ pci_write_config16(dev, 0x88, VT8237R_ACPI_IO_BASE | 0x1); + /* Enable ACPI accessm RTC signal gated with PSON. */ pci_write_config8(dev, 0x81, 0x84); - /* Allow SLP# signal to assert LDTSTOP_L. + + /* + * Allow SLP# signal to assert LDTSTOP_L. * Will work for C3 and for FID/VID change. */ - /* fixme */ - outb(0xff, VT8237R_ACPI_IO_BASE + 0x50); //fixme maybe not needed + /* FIXME */ + outb(0xff, VT8237R_ACPI_IO_BASE + 0x50); /* Maybe unneeded? */ +// outb(0x4, VT8237R_ACPI_IO_BASE + 0x50); /* Maybe unneeded? */ -// outb(0x4, VT8237R_ACPI_IO_BASE + 0x50); //fixme maybe not needed + /* It seems for AMD LDTSTP is connected not to SLP anymore. */ + /* Enable 0: DPSLP# / DPRSTP# / VRDSLP */ - /* it seems for AMD LDTSTP is connected not to SLP anymore */ - /* enable 0: DPSLP# / DPRSTP# / VRDSLP */ + /* + * Enable SATA LED, VR timer = 100us. + * Enable DPSLP# / DPRSTP# / VRDSLP - WARNING LDTSTP connetcs + * to some of those pins! (and not to SLP as on R ver). + */ + pci_write_config8(dev, 0xe5, 0x69); /* FIXME */ - /* Enable SATA LED, VR timer = 100us - * Enable DPSLP# / DPRSTP# / VRDSLP - WARNING LDTSTP connetcs to some of those pins! (and not to SLP as on R ver) + /* + * REQ5 as PCI request input - should be together with + * INTE-INTH. Fast VR timer disable - need for LDTSTP signal. */ - //fixme - pci_write_config8(dev, 0xe5, 0x69); - - /* REQ5 as PCI request input - should be together with INTE-INTH. - * Fast VR timer disable - need for LDTSTP signal - */ pci_write_config8(dev, 0xe4, 0xa5); - - /* reduce further the STPCLK/LDTSTP signal to 5us */ + /* Reduce further the STPCLK/LDTSTP signal to 5us. */ pci_write_config8(dev, 0xec, 0x4); - /* Host Bus Power Management Control, maybe not needed */ + + /* Host Bus Power Management Control, maybe not needed. */ pci_write_config8(dev, 0x8c, 0x5); - /* so the chip knows we are on AMD */ + /* So the chip knows we are on AMD. */ pci_write_config8(devctl, 0x7c, 0x77); devctl = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, - 0x2336), 0); + 0x2336), 0); if (devctl == PCI_DEV_INVALID) return; - /* Enable C2NOW delay to PSTATECTL VID / FID Change Delay to P-State Control */ + + /* + * Enable C2NOW delay to PSTATECTL VID / FID Change Delay + * to P-State Control. + */ pci_write_config8(devctl, 0xa6, 0x83); - //return; //FIXME fall through some revs have it old way + // return; // FIXME: Fall through some revs have it old way. } + /* Set ACPI base address to I/O VT8237R_ACPI_IO_BASE. */ pci_write_config16(dev, 0x88, VT8237R_ACPI_IO_BASE | 0x1); + /* Enable ACPI accessm RTC signal gated with PSON. */ pci_write_config8(dev, 0x81, 0x84); - /* Allow SLP# signal to assert LDTSTOP_L. + + /* + * Allow SLP# signal to assert LDTSTOP_L. * Will work for C3 and for FID/VID change. */ outb(0x1, VT8237R_ACPI_IO_BASE + 0x11); @@ -312,97 +324,97 @@ void enable_rom_decode(void) /* Power management controller */ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT8237R_LPC), 0); - if (dev == PCI_DEV_INVALID) { - /* Power management controller */ + /* Power management controller */ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, - PCI_DEVICE_ID_VIA_VT8237S_LPC), 0); + PCI_DEVICE_ID_VIA_VT8237S_LPC), 0); if (dev == PCI_DEV_INVALID) return; } - /* ROM decode last 1MB FFC00000 - FFFFFFFF */ + /* ROM decode last 1MB FFC00000 - FFFFFFFF. */ pci_write_config8(dev, 0x41, 0x7f); } -void vt8237_early_spi_init(void) { +void vt8237_early_spi_init(void) +{ device_t dev; volatile u16 *spireg; u32 tmp; - /* Bus Control and Power Management */ + /* Bus Control and Power Management */ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT8237S_LPC), 0); if (dev == PCI_DEV_INVALID) die("SB not found\r\n"); - /* put SPI base 20 d0 fe */ + /* Put SPI base 20 d0 fe. */ tmp = pci_read_config32(dev, 0xbc); - pci_write_config32(dev, 0xbc, (VT8237S_SPI_MEM_BASE >> 8) | (tmp & 0xFF000000)); + pci_write_config32(dev, 0xbc, + (VT8237S_SPI_MEM_BASE >> 8) | (tmp & 0xFF000000)); - /* set SPI clock to 33MHz */ + /* Set SPI clock to 33MHz. */ spireg = (u16 *) (VT8237S_SPI_MEM_BASE + 0x6c); - (*spireg) &= 0xff00; + (*spireg) &= 0xff00; } -/* offset 0x58 +/* + * Offset 0x58: * 31:20 reserved * 19:16 4 bit position in shadow EEPROM * 15:0 data to write * - * offset 0x5c + * Offset 0x5c: * 31:28 reserved * 27 ERDBG - enable read from 0x5c * 26 reserved * 25 SEELD - * 24 SEEPR - write 1 when done updating, wait until SEELD is set to 1, sticky + * 24 SEEPR - write 1 when done updating, wait until SEELD is + * set to 1, sticky * cleared by reset, if it is 1 writing is disabled * 19:16 4 bit position in shadow EEPROM * 15:0 data from shadow EEPROM * - * after PCIRESET SEELD and SEEPR must be 1 and 1 -*/ + * After PCIRESET SEELD and SEEPR must be 1 and 1. + */ -/* 1 = needs PCI reset, 0 don't reset, network initialized */ +/* 1 = needs PCI reset, 0 don't reset, network initialized. */ -/* fixme maybe close the debug register after use? */ +/* FIXME: Maybe close the debug register after use? */ #define LAN_TIMEOUT 0x7FFFFFFF -int vt8237_early_network_init(struct vt8237_network_rom *rom) { +int vt8237_early_network_init(struct vt8237_network_rom *rom) +{ struct vt8237_network_rom n; - int loops; + int i, loops; device_t dev; u32 tmp; u8 status; u16 *rom_write; unsigned int checksum; - int i; /* Network adapter */ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233_7), 0); - if (dev == PCI_DEV_INVALID) { - print_err("Network is disabled, please enable\n"); - return 0; + print_err("Network is disabled, please enable\n"); + return 0; } tmp = pci_read_config32(dev, 0x5c); - /* enable ERDBG */ - tmp |= 0x08000000; + tmp |= 0x08000000; /* Enable ERDBG. */ pci_write_config32(dev, 0x5c, tmp); - + status = ((pci_read_config32(dev, 0x5c) >> 24) & 0x3); - - if (status == 3) { - /* network controller OK, EEPROM loaded */ - return 0; - } - + + /* Network controller OK, EEPROM loaded. */ + if (status == 3) + return 0; + if (rom == NULL) { - print_err("No configuration data specified, using default MAC!\n"); + print_err("No config data specified, using default MAC!\n"); n.mac_address[0] = 0x0; n.mac_address[1] = 0x0; n.mac_address[2] = 0xde; @@ -431,40 +443,41 @@ int vt8237_early_network_init(struct vt8237_network_rom *rom) { n.checksum = 0x0; rom = &n; } - + rom_write = (u16 *) rom; checksum = 0; - /* write all data except checksum and second to last byte */ - tmp &= 0xff000000; /* leave reserved bits in */ + /* Write all data except checksum and second to last byte. */ + tmp &= 0xff000000; /* Leave reserved bits in. */ for (i = 0; i < 15; i++) { pci_write_config32(dev, 0x58, tmp | (i << 16) | rom_write[i]); - /* lame code fixme */ + /* Lame code FIXME */ checksum += rom_write[i] & 0xff; - //checksum %= 256; + /* checksum %= 256; */ checksum += (rom_write[i] >> 8) & 0xff; - //checksum %= 256; + /* checksum %= 256; */ } - + checksum += (rom_write[15] & 0xff); checksum = ~(checksum & 0xff); tmp |= (((checksum & 0xff) << 8) | rom_write[15]); - /* write last byte and checksum */ - pci_write_config32(dev, 0x58, (15 << 16) | tmp); - + /* Write last byte and checksum. */ + pci_write_config32(dev, 0x58, (15 << 16) | tmp); + tmp = pci_read_config32(dev, 0x5c); - pci_write_config32(dev, 0x5c, tmp | 0x01000000); /* toggle SEEPR */ - + pci_write_config32(dev, 0x5c, tmp | 0x01000000); /* Toggle SEEPR. */ + /* Yes, this is a mess, but it's the easiest way to do it. */ - while ( (((pci_read_config32(dev, 0x5c) >> 25) & 1) == 0) - && (loops < LAN_TIMEOUT)) + while ((((pci_read_config32(dev, 0x5c) >> 25) & 1) == 0) + && (loops < LAN_TIMEOUT)) { ++loops; + } if (loops >= LAN_TIMEOUT) { - print_err("Timout - LAN controller did not accept configuration\n"); - return 0; + print_err("Timeout - LAN controller didn't accept config\n"); + return 0; } - - /* we are done, config will be used after PCIRST# */ + + /* We are done, config will be used after PCIRST#. */ return 1; } diff --git a/src/southbridge/via/vt8237r/vt8237r_lpc.c b/src/southbridge/via/vt8237r/vt8237r_lpc.c index 4d24e6161d..e67e5cbb41 100644 --- a/src/southbridge/via/vt8237r/vt8237r_lpc.c +++ b/src/southbridge/via/vt8237r/vt8237r_lpc.c @@ -54,8 +54,8 @@ static struct ioapicreg { } ioapic_table[] = { /* IO-APIC virtual wire mode configuration. */ /* mask, trigger, polarity, destination, delivery, vector */ - {0, ENABLED | TRIGGER_EDGE | POLARITY_HIGH | PHYSICAL_DEST | - ExtINT, NONE}, + {0, ENABLED | TRIGGER_EDGE | POLARITY_HIGH | PHYSICAL_DEST | + ExtINT, NONE}, { {1, DISABLED, NONE}, {2, DISABLED, NONE}, {3, DISABLED, NONE}, @@ -167,13 +167,15 @@ static void setup_pm(device_t dev) /* GP Timer Control 1s */ pci_write_config8(dev, 0x93, 0x88); - /* 7 = SMBus clock from RTC 32.768KHz + /* + * 7 = SMBus clock from RTC 32.768KHz * 5 = Internal PLL reset from susp * 2 = GPO2 is GPIO */ pci_write_config8(dev, 0x94, 0xa4); - /* 7 = stp to sust delay 1msec + /* + * 7 = stp to sust delay 1msec * 6 = SUSST# Deasserted Before PWRGD for STD * 4 = PWRGOOD reset on VT8237A/S * 3 = GPO26/GPO27 is GPO @@ -216,14 +218,14 @@ static void setup_pm(device_t dev) /* SCI is generated for RTC/pwrBtn/slpBtn. */ outw(0x001, VT8237R_ACPI_IO_BASE + 0x04); - } - -static void vt8237r_init(struct device *dev) { +static void vt8237r_init(struct device *dev) +{ u8 enables; - /* Enable SATA LED, disable special CPU Frequency Change - + /* + * Enable SATA LED, disable special CPU Frequency Change - * GPIO28 GPIO22 GPIO29 GPIO23 are GPIOs. */ pci_write_config8(dev, 0xe5, 0x9); @@ -236,14 +238,18 @@ static void vt8237r_init(struct device *dev) { enables |= 0x08; pci_write_config8(dev, 0x4f, enables); - /* Set Read Pass Write Control Enable (force A2 from APIC FSB to low). */ + /* + * Set Read Pass Write Control Enable + * (force A2 from APIC FSB to low). + */ pci_write_config8(dev, 0x48, 0x8c); southbridge_init_common(dev); /* FIXME: Intel needs more bit set for C2/C3. */ - /* Allow SLP# signal to assert LDTSTOP_L. + /* + * Allow SLP# signal to assert LDTSTOP_L. * Will work for C3 and for FID/VID change. */ outb(0x1, VT8237R_ACPI_IO_BASE + 0x11); @@ -252,40 +258,43 @@ static void vt8237r_init(struct device *dev) { static void vt8237s_init(struct device *dev) { u32 tmp; - - /* put SPI base VT8237S_SPI_MEM_BASE */ + + /* Put SPI base VT8237S_SPI_MEM_BASE. */ tmp = pci_read_config32(dev, 0xbc); - pci_write_config32(dev, 0xbc, (VT8237S_SPI_MEM_BASE >> 8) | (tmp & 0xFF000000)); + pci_write_config32(dev, 0xbc, + (VT8237S_SPI_MEM_BASE >> 8) | (tmp & 0xFF000000)); - /* Enable SATA LED, VR timer = 100us, VR timer should be fixed */ - + /* Enable SATA LED, VR timer = 100us, VR timer should be fixed. */ pci_write_config8(dev, 0xe5, 0x69); - /* REQ5 as PCI request input - should be together with INTE-INTH. - * Fast VR timer disable - need for LDTSTOP_L signal - */ + /* + * REQ5 as PCI request input - should be together with INTE-INTH. + * Fast VR timer disable - need for LDTSTOP_L signal. + */ pci_write_config8(dev, 0xe4, 0xa5); - /* reduce further the STPCLK/LDTSTP signal to 5us */ - + /* Reduce further the STPCLK/LDTSTP signal to 5us. */ pci_write_config8(dev, 0xec, 0x4); /* Host Bus Power Management Control, maybe not needed */ pci_write_config8(dev, 0x8c, 0x5); - /* Enable HPET at VT8237R_HPET_ADDR., does not work correctly on R */ + /* Enable HPET at VT8237R_HPET_ADDR., does not work correctly on R. */ pci_write_config32(dev, 0x68, (VT8237R_HPET_ADDR | 0x80)); southbridge_init_common(dev); - + /* FIXME: Intel needs more bit set for C2/C3. */ - /* Allow SLP# signal to assert LDTSTOP_L. - * Will work for C3 and for FID/VID change. FIXME FIXME, pre rev A2 + /* + * Allow SLP# signal to assert LDTSTOP_L. + * Will work for C3 and for FID/VID change. FIXME FIXME, pre rev A2. */ outb(0xff, VT8237R_ACPI_IO_BASE + 0x50); + dump_south(dev); } + static void vt8237_common_init(struct device *dev) { u8 enables, byte; @@ -315,7 +324,8 @@ static void vt8237_common_init(struct device *dev) */ pci_write_config8(dev, 0x41, 0x7f); - /* Set bit 6 of 0x40 (I/O recovery time). + /* + * Set bit 6 of 0x40 (I/O recovery time). * IMPORTANT FIX - EISA = ECLR reg at 0x4d0! Decoding must be on so * that PCI interrupts can be properly marked as level triggered. */ @@ -338,11 +348,12 @@ static void vt8237_common_init(struct device *dev) pci_write_config8(dev, 0x59, 0x80); /* - * bit meaning - * 3 Bypass APIC De-Assert Message (1=Enable) - * 1 possibly "INTE#, INTF#, INTG#, INTH# as PCI" - * bit 1=1 works for Aaron at VIA, bit 1=0 works for jakllsch - * 0 Dynamic Clock Gating Main Switch (1=Enable) + * Bit | Meaning + * ------------- + * 3 | Bypass APIC De-Assert Message (1=Enable) + * 1 | possibly "INTE#, INTF#, INTG#, INTH# as PCI" + * | bit 1=1 works for Aaron at VIA, bit 1=0 works for jakllsch + * 0 | Dynamic Clock Gating Main Switch (1=Enable) */ pci_write_config8(dev, 0x5b, 0xb); @@ -410,7 +421,6 @@ static const struct device_operations vt8237r_lpc_ops_s = { .scan_bus = scan_static_bus, }; - static const struct device_operations vt8237r_lpc_ops_r = { .read_resources = vt8237r_read_resources, .set_resources = pci_dev_set_resources, diff --git a/src/southbridge/via/vt8237r/vt8237r_sata.c b/src/southbridge/via/vt8237r/vt8237r_sata.c index 77d7b0c3e2..a445476265 100644 --- a/src/southbridge/via/vt8237r/vt8237r_sata.c +++ b/src/southbridge/via/vt8237r/vt8237r_sata.c @@ -39,37 +39,43 @@ static void sata_i_init(struct device *dev) pci_write_config8(dev, PCI_CLASS_DEVICE, 0x1); reg |= 0x80; /* Sub Class Write Protect on */ pci_write_config8(dev, SATA_MISC_CTRL, reg); - + return; } -static void sata_ii_init(struct device *dev) { +static void sata_ii_init(struct device *dev) +{ u8 reg; sata_i_init(dev); - - /* analog black magic, you may or may not need to adjust 0x60-0x6f, depends on PCB */ - - /* Analog PHY - gen1 + + /* + * Analog black magic, you may or may not need to adjust 0x60-0x6f, + * depends on PCB. + */ + + /* + * Analog PHY - gen1 * CDR bandwidth [6:5] = 3 * Squelch Window Select [4:3] = 1 * CDR Charge Pump [2:0] = 1 */ - + pci_write_config8(dev, 0x64, 0x49); - - /* adjust driver current source value to 9 */ + + /* Adjust driver current source value to 9. */ reg = pci_read_config8(dev, 0x65); reg &= 0xf0; reg |= 0x9; pci_write_config8(dev, 0x65, reg); - - /* set all manual termination 50ohm bits [2:0] and enable [4] */ + + /* Set all manual termination 50ohm bits [2:0] and enable [4]. */ reg = pci_read_config8(dev, 0x6a); reg |= 0xf; pci_write_config8(dev, 0x6a, reg); - /* Analog PHY - gen2 + /* + * Analog PHY - gen2 * CDR bandwidth [5:4] = 2 * Pre / De-emphasis Level [7:6] controls bits [3:2], rest in 0x6e * CDR Charge Pump [2:0] = 1 @@ -80,10 +86,10 @@ static void sata_ii_init(struct device *dev) { reg |= 0x61; pci_write_config8(dev, 0x6f, reg); - /* check if staggered spinup is supported */ + /* Check if staggered spinup is supported. */ reg = pci_read_config8(dev, 0x83); if ((reg & 0x8) == 0) { - /* start OOB sequence on both drives */ + /* Start OOB sequence on both drives. */ reg |= 0x30; pci_write_config8(dev, 0x83, reg); } |