summaryrefslogtreecommitdiff
path: root/src/southbridge
diff options
context:
space:
mode:
authorRudolf Marek <r.marek@assembler.cz>2008-09-05 18:20:57 +0000
committerRudolf Marek <r.marek@assembler.cz>2008-09-05 18:20:57 +0000
commitd9f29c8e5e3f37335a9b737361acc286df5248f0 (patch)
tree68462a0f09560e74e52d1d5c63a386a8a5679330 /src/southbridge
parent10d0a81ec1c6ccedac291824eed8980d011b0ab9 (diff)
downloadcoreboot-d9f29c8e5e3f37335a9b737361acc286df5248f0.tar.xz
This patch adds support for the VIA VT8237S south bridge. The VT8237R programming remains unchanged (tested
on mine desktop) except of reverting the small change introduced by Bari (gpio/inta setup reg 0x5b). This should go for some board specific file. The change would broke at least mine board. But seems to be needed for jakllsch. Signed-off-by: Rudolf Marek <r.marek@assembler.cz> Acked-by: Bari Ari <bari@onelabs.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Diffstat (limited to 'src/southbridge')
-rw-r--r--src/southbridge/via/vt8237r/Config.lb1
-rw-r--r--src/southbridge/via/vt8237r/vt8237_ctrl.c186
-rw-r--r--src/southbridge/via/vt8237r/vt8237r.h27
-rw-r--r--src/southbridge/via/vt8237r/vt8237r_early_smbus.c253
-rw-r--r--src/southbridge/via/vt8237r/vt8237r_lpc.c118
-rw-r--r--src/southbridge/via/vt8237r/vt8237r_sata.c75
6 files changed, 619 insertions, 41 deletions
diff --git a/src/southbridge/via/vt8237r/Config.lb b/src/southbridge/via/vt8237r/Config.lb
index 90feb0f9ef..2c01d41a2e 100644
--- a/src/southbridge/via/vt8237r/Config.lb
+++ b/src/southbridge/via/vt8237r/Config.lb
@@ -20,6 +20,7 @@
config chip.h
driver vt8237r.o
+driver vt8237_ctrl.o
driver vt8237r_ide.o
driver vt8237r_lpc.o
driver vt8237r_sata.o
diff --git a/src/southbridge/via/vt8237r/vt8237_ctrl.c b/src/southbridge/via/vt8237r/vt8237_ctrl.c
new file mode 100644
index 0000000000..666fbcf68c
--- /dev/null
+++ b/src/southbridge/via/vt8237r/vt8237_ctrl.c
@@ -0,0 +1,186 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Rudolf Marek <r.marek@assembler.cz>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License v2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ops.h>
+#include <device/pci_ids.h>
+#include <console/console.h>
+
+/* We support here K8M890/K8T890 and VT8237/S/A PCI1/Vlink */
+
+static void vt8237_cfg(struct device *dev)
+{
+ u8 regm, regm2, regm3;
+
+ device_t devfun3;
+
+ devfun3 = dev_find_device(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_K8T890CE_3, 0);
+
+ if (!devfun3)
+ devfun3 = dev_find_device(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_K8M890CE_3, 0);
+
+ if (!devfun3)
+ die("Unknown NB");
+
+ /* CPU to PCI Flow Control 1 & 2, just fill in recommended */
+ pci_write_config8(dev, 0x70, 0xc2);
+ pci_write_config8(dev, 0x71, 0xc8);
+
+ /* PCI Control */
+ pci_write_config8(dev, 0x72, 0xee);
+ pci_write_config8(dev, 0x73, 0x01);
+ pci_write_config8(dev, 0x74, 0x3c);
+ pci_write_config8(dev, 0x75, 0x0f);
+ pci_write_config8(dev, 0x76, 0x50);
+ pci_write_config8(dev, 0x77, 0x48);
+ pci_write_config8(dev, 0x78, 0x01);
+ /* APIC on HT */
+ pci_write_config8(dev, 0x7c, 0x77); //maybe Enable LDT APIC Mode bit3 set to 1
+
+ /* WARNING: Need to copy some registers from NB (D0F3) to SB (D11F7). */
+
+ regm = pci_read_config8(devfun3, 0x88); /* Shadow mem CTRL */
+ pci_write_config8(dev, 0x57, regm);
+
+ regm = pci_read_config8(devfun3, 0x80); /* Shadow page C */
+ pci_write_config8(dev, 0x61, regm);
+
+ regm = pci_read_config8(devfun3, 0x81); /* Shadow page D */
+ pci_write_config8(dev, 0x62, regm);
+
+ /* Shadow page F + memhole copy */
+ regm = pci_read_config8(devfun3, 0x83);
+ pci_write_config8(dev, 0x63, regm);
+
+ regm3 = pci_read_config8(devfun3, 0x82);/* Shadow page E */
+ pci_write_config8(dev, 0x64, regm);
+
+ regm = pci_read_config8(devfun3, 0x86); /* SMM and APIC decoding */
+ pci_write_config8(dev, 0xe6, regm);
+}
+
+/**
+ * Example of setup: Setup the V-Link for VT8237R, 8X mode.
+ *
+ * For K8T890CF VIA recommends what is in VIA column, AW is award 8X:
+ *
+ * REG DEF AW VIA-8X VIA-4X
+ * -----------------------------
+ * NB V-Link Manual Driving Control strobe 0xb5 0x46 0x46 0x88 0x88
+ * NB V-Link Manual Driving Control - Data 0xb6 0x46 0x46 0x88 0x88
+ * NB V-Link Receiving Strobe Delay 0xb7 0x02 0x02 0x61 0x01
+ * NB V-Link Compensation Control bit4,0 (b5,b6) 0xb4 0x10 0x10 0x11 0x11
+ * SB V-Link Strobe Drive Control 0xb9 0x00 0xa5 0x98 0x98
+ * SB V-Link Data drive Control???? 0xba 0x00 0xbb 0x77 0x77
+ * SB V-Link Receive Strobe Delay???? 0xbb 0x04 0x11 0x11 0x11
+ * SB V-Link Compensation Control bit0 (use b9) 0xb8 0x00 0x01 0x01 0x01
+ * V-Link CKG Control 0xb0 0x05 0x05 0x06 0x03
+ * V-Link CKG Control 0xb1 0x05 0x05 0x01 0x03
+ */
+
+static void vt8237s_vlink_init(struct device *dev)
+{
+ u8 reg;
+
+ device_t devfun7;
+
+ devfun7 = dev_find_device(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_K8T890CE_7, 0);
+
+ if (!devfun7)
+ devfun7 = dev_find_device(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_K8M890CE_7, 0);
+
+ /* no pairing NB found */
+ if (!devfun7)
+ return;
+
+ /*
+ * This init code is valid only for the VT8237S! For different
+ * sounthbridges (e.g. VT8237A, VT8237S, VT8237R (without plus R)
+ * and VT8251) a different init code is required.
+ */
+
+ pci_write_config8(devfun7, 0xb5, 0x66);
+ pci_write_config8(devfun7, 0xb6, 0x66);
+ pci_write_config8(devfun7, 0xb7, 0x65);
+
+ reg = pci_read_config8(devfun7, 0xb4);
+ reg |= 0x1;
+ pci_write_config8(devfun7, 0xb4, reg);
+
+ pci_write_config8(dev, 0xb9, 0x68);
+ pci_write_config8(dev, 0xba, 0x88);
+ pci_write_config8(dev, 0xbb, 0x89);
+
+
+ reg = pci_read_config8(dev, 0xbd);
+ reg |= 0x3;
+ pci_write_config8(dev, 0xbd, reg);
+
+ /* Program V-link 8X 8bit full duplex, parity disabled FIXME */
+ pci_write_config8(dev, 0x48, 0x13);
+}
+
+static void ctrl_enable(struct device *dev) {
+
+ /* enable the 0:13 and 0:13.1 */
+ /* FIXME */
+ pci_write_config8(dev, 0x4f, 0x43);
+}
+
+
+extern void dump_south(device_t dev);
+
+static void ctrl_init(struct device *dev) {
+
+ /* TODO: Fix some ordering issue fo V-link set Rx77[6] and PCI1_Rx4F[0]
+ should to 1 FIXME DO you need?*/
+
+ /* VT8237R specific configuration other SB are done in their own directories */
+ /* add A version */
+ device_t devsb = dev_find_device(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_VT8237S_LPC, 0);
+ if (devsb) {
+ /* FIXME: Skip v-link setup for now */
+// vt8237s_vlink_init(dev);
+ }
+
+ /* configure PCI1 and copy mirror registers from D0F3 */
+ vt8237_cfg(dev);
+ dump_south(dev);
+}
+
+static const struct device_operations ctrl_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = ctrl_init,
+ .enable = ctrl_enable,
+ .ops_pci = 0,
+};
+
+static const struct pci_driver northbridge_driver_t __pci_driver = {
+ .ops = &ctrl_ops,
+ .vendor = PCI_VENDOR_ID_VIA,
+ .device = PCI_DEVICE_ID_VIA_VT8237_VLINK,
+};
diff --git a/src/southbridge/via/vt8237r/vt8237r.h b/src/southbridge/via/vt8237r/vt8237r.h
index 444500b82a..231553bc11 100644
--- a/src/southbridge/via/vt8237r/vt8237r.h
+++ b/src/southbridge/via/vt8237r/vt8237r.h
@@ -20,6 +20,8 @@
#ifndef SOUTHBRIDGE_VIA_VT8237R_VT8237R_H
#define SOUTHBRIDGE_VIA_VT8237R_VT8237R_H
+#include <stdint.h>
+
/* Static resources for the VT8237R southbridge */
#define VT8237R_APIC_ID 0x2
@@ -27,6 +29,7 @@
#define VT8237R_SMBUS_IO_BASE 0x400
/* 0x0 disabled, 0x2 reserved, 0xf = IRQ15 */
#define VT8237R_ACPI_IRQ 0x9
+#define VT8237S_SPI_MEM_BASE 0xfed02000ULL
#define VT8237R_HPET_ADDR 0xfed00000ULL
#define VT8237R_APIC_BASE 0xfec00000ULL
@@ -68,4 +71,28 @@
#define SMBUS_DELAY() inb(0x80)
+struct vt8237_network_rom {
+ u8 mac_address[6];
+ u8 phy_addr;
+ u8 res1;
+ u16 sub_sid;
+ u16 sub_vid;
+ u16 pid;
+ u16 vid;
+ u8 pmcc;
+ u8 data_sel;
+ u8 pmu_data_reg;
+ u8 aux_curr;
+ u16 reserved;
+ u8 min_gnt;
+ u8 max_lat;
+ u8 bcr0;
+ u8 bcr1;
+ u8 cfg_a;
+ u8 cfg_b;
+ u8 cfg_c;
+ u8 cfg_d;
+ u8 checksum;
+} __attribute__ ((packed));
+
#endif
diff --git a/src/southbridge/via/vt8237r/vt8237r_early_smbus.c b/src/southbridge/via/vt8237r/vt8237r_early_smbus.c
index 5e62f39e4d..5b865d3814 100644
--- a/src/southbridge/via/vt8237r/vt8237r_early_smbus.c
+++ b/src/southbridge/via/vt8237r/vt8237r_early_smbus.c
@@ -128,7 +128,6 @@ u8 smbus_read_byte(u8 dimm, u8 offset)
return val;
}
-
/**
* Enable the smbus on vt8237r-based systems
*/
@@ -137,11 +136,17 @@ void enable_smbus(void)
device_t dev;
/* Power management controller */
+
dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
PCI_DEVICE_ID_VIA_VT8237R_LPC), 0);
- if (dev == PCI_DEV_INVALID)
- die("Power management controller not found\r\n");
+ if (dev == PCI_DEV_INVALID) {
+ /* Power management controller */
+ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_VT8237S_LPC), 0);
+ if (dev == PCI_DEV_INVALID)
+ die("Power management controller not found\r\n");
+ }
/* 7 = SMBus Clock from RTC 32.768KHz
* 5 = Internal PLL reset from susp
@@ -213,17 +218,253 @@ void smbus_fixup(const struct mem_controller *ctrl)
PRINT_DEBUG("Done\r\n");
}
+/* fixme better separate the NB and SB, will done once it works */
+
+void vt8237_sb_enable_fid_vid(void) {
+ device_t dev;
+ device_t devctl;
+
+ /* Power management controller */
+ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_VT8237R_LPC), 0);
+
+ if (dev == PCI_DEV_INVALID) {
+ /* Power management controller */
+ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_VT8237S_LPC), 0);
+ if (dev == PCI_DEV_INVALID)
+ return;
+
+ devctl = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_VT8237_VLINK), 0);
+ if (devctl == PCI_DEV_INVALID)
+ return;
+
+ {
+ u8 tmp;
+ tmp = pci_read_config8(devctl, 0xec);
+ print_debug("EC is ");
+ print_debug_hex8(tmp);
+ print_debug(" E5 is ");
+ tmp = pci_read_config8(dev, 0xe5);
+ print_debug_hex8(tmp);
+
+ }
+ /* Set ACPI base address to I/O VT8237R_ACPI_IO_BASE. */
+ pci_write_config16(dev, 0x88, VT8237R_ACPI_IO_BASE | 0x1);
+ /* Enable ACPI accessm RTC signal gated with PSON. */
+ pci_write_config8(dev, 0x81, 0x84);
+ /* Allow SLP# signal to assert LDTSTOP_L.
+ * Will work for C3 and for FID/VID change.
+ */
+
+ /* fixme */
+ outb(0xff, VT8237R_ACPI_IO_BASE + 0x50); //fixme maybe not needed
+
+// outb(0x4, VT8237R_ACPI_IO_BASE + 0x50); //fixme maybe not needed
+
+ /* it seems for AMD LDTSTP is connected not to SLP anymore */
+ /* enable 0: DPSLP# / DPRSTP# / VRDSLP */
+
+ /* Enable SATA LED, VR timer = 100us
+ * Enable DPSLP# / DPRSTP# / VRDSLP - WARNING LDTSTP connetcs to some of those pins! (and not to SLP as on R ver)
+ */
+ //fixme
+ pci_write_config8(dev, 0xe5, 0x69);
+
+ /* REQ5 as PCI request input - should be together with INTE-INTH.
+ * Fast VR timer disable - need for LDTSTP signal
+ */
+ pci_write_config8(dev, 0xe4, 0xa5);
+
+ /* reduce further the STPCLK/LDTSTP signal to 5us */
+
+ pci_write_config8(dev, 0xec, 0x4);
+ /* Host Bus Power Management Control, maybe not needed */
+ pci_write_config8(dev, 0x8c, 0x5);
+
+ /* so the chip knows we are on AMD */
+ pci_write_config8(devctl, 0x7c, 0x77);
+
+ devctl = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
+ 0x2336), 0);
+ if (devctl == PCI_DEV_INVALID)
+ return;
+ /* Enable C2NOW delay to PSTATECTL VID / FID Change Delay to P-State Control */
+ pci_write_config8(devctl, 0xa6, 0x83);
+
+ //return; //FIXME fall through some revs have it old way
+ }
+ /* Set ACPI base address to I/O VT8237R_ACPI_IO_BASE. */
+ pci_write_config16(dev, 0x88, VT8237R_ACPI_IO_BASE | 0x1);
+ /* Enable ACPI accessm RTC signal gated with PSON. */
+ pci_write_config8(dev, 0x81, 0x84);
+ /* Allow SLP# signal to assert LDTSTOP_L.
+ * Will work for C3 and for FID/VID change.
+ */
+ outb(0x1, VT8237R_ACPI_IO_BASE + 0x11);
+}
+
void enable_rom_decode(void)
{
device_t dev;
- /* Bus Control and Power Management */
+ /* Power management controller */
dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
PCI_DEVICE_ID_VIA_VT8237R_LPC), 0);
- if (dev == PCI_DEV_INVALID)
- die("SB not found\r\n");
+ if (dev == PCI_DEV_INVALID) {
+ /* Power management controller */
+ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_VT8237S_LPC), 0);
+ if (dev == PCI_DEV_INVALID)
+ return;
+ }
/* ROM decode last 1MB FFC00000 - FFFFFFFF */
pci_write_config8(dev, 0x41, 0x7f);
}
+
+void vt8237_early_spi_init(void) {
+ device_t dev;
+ volatile u16 *spireg;
+ u32 tmp;
+
+ /* Bus Control and Power Management */
+ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_VT8237S_LPC), 0);
+
+ if (dev == PCI_DEV_INVALID)
+ die("SB not found\r\n");
+
+ /* put SPI base 20 d0 fe */
+ tmp = pci_read_config32(dev, 0xbc);
+ pci_write_config32(dev, 0xbc, (VT8237S_SPI_MEM_BASE >> 8) | (tmp & 0xFF000000));
+
+ /* set SPI clock to 33MHz */
+ spireg = (u16 *) (VT8237S_SPI_MEM_BASE + 0x6c);
+ (*spireg) &= 0xff00;
+}
+
+/* offset 0x58
+ * 31:20 reserved
+ * 19:16 4 bit position in shadow EEPROM
+ * 15:0 data to write
+ *
+ * offset 0x5c
+ * 31:28 reserved
+ * 27 ERDBG - enable read from 0x5c
+ * 26 reserved
+ * 25 SEELD
+ * 24 SEEPR - write 1 when done updating, wait until SEELD is set to 1, sticky
+ * cleared by reset, if it is 1 writing is disabled
+ * 19:16 4 bit position in shadow EEPROM
+ * 15:0 data from shadow EEPROM
+ *
+ * after PCIRESET SEELD and SEEPR must be 1 and 1
+*/
+
+/* 1 = needs PCI reset, 0 don't reset, network initialized */
+
+/* fixme maybe close the debug register after use? */
+
+#define LAN_TIMEOUT 0x7FFFFFFF
+
+int vt8237_early_network_init(struct vt8237_network_rom *rom) {
+ struct vt8237_network_rom n;
+ int loops;
+ device_t dev;
+ u32 tmp;
+ u8 status;
+ u16 *rom_write;
+ unsigned int checksum;
+ int i;
+
+ /* Network adapter */
+ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_VIA,
+ PCI_DEVICE_ID_VIA_8233_7), 0);
+
+ if (dev == PCI_DEV_INVALID) {
+ print_err("Network is disabled, please enable\n");
+ return 0;
+ }
+
+ tmp = pci_read_config32(dev, 0x5c);
+ /* enable ERDBG */
+ tmp |= 0x08000000;
+ pci_write_config32(dev, 0x5c, tmp);
+
+ status = ((pci_read_config32(dev, 0x5c) >> 24) & 0x3);
+
+ if (status == 3) {
+ /* network controller OK, EEPROM loaded */
+ return 0;
+ }
+
+ if (rom == NULL) {
+ print_err("No configuration data specified, using default MAC!\n");
+ n.mac_address[0] = 0x0;
+ n.mac_address[1] = 0x0;
+ n.mac_address[2] = 0xde;
+ n.mac_address[3] = 0xad;
+ n.mac_address[4] = 0xbe;
+ n.mac_address[5] = 0xef;
+ n.phy_addr = 0x1;
+ n.res1 = 0x0;
+ n.sub_sid = 0x102;
+ n.sub_vid = 0x1106;
+ n.pid = 0x3065;
+ n.vid = 0x1106;
+ n.pmcc = 0x1f;
+ n.data_sel = 0x10;
+ n.pmu_data_reg = 0x0;
+ n.aux_curr = 0x0;
+ n.reserved = 0x0;
+ n.min_gnt = 0x3;
+ n.max_lat = 0x8;
+ n.bcr0 = 0x9;
+ n.bcr1 = 0xe;
+ n.cfg_a = 0x3;
+ n.cfg_b = 0x0;
+ n.cfg_c = 0x40;
+ n.cfg_d = 0x82;
+ n.checksum = 0x0;
+ rom = &n;
+ }
+
+ rom_write = (u16 *) rom;
+ checksum = 0;
+ /* write all data except checksum and second to last byte */
+ tmp &= 0xff000000; /* leave reserved bits in */
+ for (i = 0; i < 15; i++) {
+ pci_write_config32(dev, 0x58, tmp | (i << 16) | rom_write[i]);
+ /* lame code fixme */
+ checksum += rom_write[i] & 0xff;
+ //checksum %= 256;
+ checksum += (rom_write[i] >> 8) & 0xff;
+ //checksum %= 256;
+ }
+
+ checksum += (rom_write[15] & 0xff);
+ checksum = ~(checksum & 0xff);
+ tmp |= (((checksum & 0xff) << 8) | rom_write[15]);
+
+ /* write last byte and checksum */
+ pci_write_config32(dev, 0x58, (15 << 16) | tmp);
+
+ tmp = pci_read_config32(dev, 0x5c);
+ pci_write_config32(dev, 0x5c, tmp | 0x01000000); /* toggle SEEPR */
+
+ /* Yes, this is a mess, but it's the easiest way to do it. */
+ while ( (((pci_read_config32(dev, 0x5c) >> 25) & 1) == 0)
+ && (loops < LAN_TIMEOUT))
+ ++loops;
+
+ if (loops >= LAN_TIMEOUT) {
+ print_err("Timout - LAN controller did not accept configuration\n");
+ return 0;
+ }
+
+ /* we are done, config will be used after PCIRST# */
+ return 1;
+}
diff --git a/src/southbridge/via/vt8237r/vt8237r_lpc.c b/src/southbridge/via/vt8237r/vt8237r_lpc.c
index d4721a23f3..4d24e6161d 100644
--- a/src/southbridge/via/vt8237r/vt8237r_lpc.c
+++ b/src/southbridge/via/vt8237r/vt8237r_lpc.c
@@ -1,7 +1,7 @@
/*
* This file is part of the coreboot project.
*
- * Copyright (C) 2007 Rudolf Marek <r.marek@assembler.cz>
+ * Copyright (C) 2007, 2008 Rudolf Marek <r.marek@assembler.cz>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License v2 as published by
@@ -116,6 +116,8 @@ static void setup_ioapic(u32 ioapic_base)
}
}
+static void southbridge_init_common(struct device *dev);
+
/** Set up PCI IRQ routing, route everything through APIC. */
static void pci_routing_fixup(struct device *dev)
{
@@ -173,6 +175,7 @@ static void setup_pm(device_t dev)
/* 7 = stp to sust delay 1msec
* 6 = SUSST# Deasserted Before PWRGD for STD
+ * 4 = PWRGOOD reset on VT8237A/S
* 3 = GPO26/GPO27 is GPO
* 2 = Disable Alert on Lan
*/
@@ -181,14 +184,6 @@ static void setup_pm(device_t dev)
/* Disable GP3 timer. */
pci_write_config8(dev, 0x98, 0);
- /* Enable SATA LED, disable special CPU Frequency Change -
- * GPIO28 GPIO22 GPIO29 GPIO23 are GPIOs.
- */
- pci_write_config8(dev, 0xe5, 0x9);
-
- /* REQ5 as PCI request input - should be together with INTE-INTH. */
- pci_write_config8(dev, 0xe4, 0x4);
-
/* Enable ACPI accessm RTC signal gated with PSON. */
pci_write_config8(dev, 0x81, 0x84);
@@ -222,6 +217,30 @@ static void setup_pm(device_t dev)
/* SCI is generated for RTC/pwrBtn/slpBtn. */
outw(0x001, VT8237R_ACPI_IO_BASE + 0x04);
+}
+
+
+static void vt8237r_init(struct device *dev) {
+ u8 enables;
+
+ /* Enable SATA LED, disable special CPU Frequency Change -
+ * GPIO28 GPIO22 GPIO29 GPIO23 are GPIOs.
+ */
+ pci_write_config8(dev, 0xe5, 0x9);
+
+ /* REQ5 as PCI request input - should be together with INTE-INTH. */
+ pci_write_config8(dev, 0xe4, 0x4);
+
+ /* Set bit 3 of 0x4f (use INIT# as CPU reset). */
+ enables = pci_read_config8(dev, 0x4f);
+ enables |= 0x08;
+ pci_write_config8(dev, 0x4f, enables);
+
+ /* Set Read Pass Write Control Enable (force A2 from APIC FSB to low). */
+ pci_write_config8(dev, 0x48, 0x8c);
+
+ southbridge_init_common(dev);
+
/* FIXME: Intel needs more bit set for C2/C3. */
/* Allow SLP# signal to assert LDTSTOP_L.
@@ -230,7 +249,44 @@ static void setup_pm(device_t dev)
outb(0x1, VT8237R_ACPI_IO_BASE + 0x11);
}
-static void vt8237r_init(struct device *dev)
+static void vt8237s_init(struct device *dev)
+{
+ u32 tmp;
+
+ /* put SPI base VT8237S_SPI_MEM_BASE */
+ tmp = pci_read_config32(dev, 0xbc);
+ pci_write_config32(dev, 0xbc, (VT8237S_SPI_MEM_BASE >> 8) | (tmp & 0xFF000000));
+
+ /* Enable SATA LED, VR timer = 100us, VR timer should be fixed */
+
+ pci_write_config8(dev, 0xe5, 0x69);
+
+ /* REQ5 as PCI request input - should be together with INTE-INTH.
+ * Fast VR timer disable - need for LDTSTOP_L signal
+ */
+ pci_write_config8(dev, 0xe4, 0xa5);
+
+ /* reduce further the STPCLK/LDTSTP signal to 5us */
+
+ pci_write_config8(dev, 0xec, 0x4);
+
+ /* Host Bus Power Management Control, maybe not needed */
+ pci_write_config8(dev, 0x8c, 0x5);
+
+ /* Enable HPET at VT8237R_HPET_ADDR., does not work correctly on R */
+ pci_write_config32(dev, 0x68, (VT8237R_HPET_ADDR | 0x80));
+
+ southbridge_init_common(dev);
+
+ /* FIXME: Intel needs more bit set for C2/C3. */
+
+ /* Allow SLP# signal to assert LDTSTOP_L.
+ * Will work for C3 and for FID/VID change. FIXME FIXME, pre rev A2
+ */
+ outb(0xff, VT8237R_ACPI_IO_BASE + 0x50);
+ dump_south(dev);
+}
+static void vt8237_common_init(struct device *dev)
{
u8 enables, byte;
@@ -275,7 +331,7 @@ static void vt8237r_init(struct device *dev)
/* Delay transaction control */
pci_write_config8(dev, 0x43, 0xb);
- /* I/O recovery time */
+ /* I/O recovery time, default IDE routing */
pci_write_config8(dev, 0x4c, 0x44);
/* ROM memory cycles go to LPC. */
@@ -288,25 +344,14 @@ static void vt8237r_init(struct device *dev)
* bit 1=1 works for Aaron at VIA, bit 1=0 works for jakllsch
* 0 Dynamic Clock Gating Main Switch (1=Enable)
*/
- pci_write_config8(dev, 0x5b, 0x9);
-
- /* Set Read Pass Write Control Enable (force A2 from APIC FSB to low). */
- pci_write_config8(dev, 0x48, 0x8c);
+ pci_write_config8(dev, 0x5b, 0xb);
/* Set 0x58 to 0x43 APIC and RTC. */
pci_write_config8(dev, 0x58, 0x43);
- /* Set bit 3 of 0x4f (use INIT# as CPU reset). */
- enables = pci_read_config8(dev, 0x4f);
- enables |= 0x08;
- pci_write_config8(dev, 0x4f, enables);
-
/* Enable serial IRQ, 6PCI clocks. */
pci_write_config8(dev, 0x52, 0x9);
- /* Enable HPET at VT8237R_HPET_ADDR. */
- pci_write_config32(dev, 0x68, (VT8237R_HPET_ADDR | 0x80));
-
/* Power management setup */
setup_pm(dev);
@@ -348,25 +393,40 @@ static void init_keyboard(struct device *dev)
init_pc_keyboard(0x60, 0x64, 0);
}
-static void southbridge_init(struct device *dev)
+static void southbridge_init_common(struct device *dev)
{
- vt8237r_init(dev);
+ vt8237_common_init(dev);
pci_routing_fixup(dev);
setup_ioapic(VT8237R_APIC_BASE);
setup_i8259();
init_keyboard(dev);
}
-static const struct device_operations vt8237r_lpc_ops = {
+static const struct device_operations vt8237r_lpc_ops_s = {
+ .read_resources = vt8237r_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = vt8237r_enable_resources,
+ .init = &vt8237s_init,
+ .scan_bus = scan_static_bus,
+};
+
+
+static const struct device_operations vt8237r_lpc_ops_r = {
.read_resources = vt8237r_read_resources,
.set_resources = pci_dev_set_resources,
.enable_resources = vt8237r_enable_resources,
- .init = &southbridge_init,
+ .init = &vt8237r_init,
.scan_bus = scan_static_bus,
};
-static const struct pci_driver lpc_driver __pci_driver = {
- .ops = &vt8237r_lpc_ops,
+static const struct pci_driver lpc_driver_r __pci_driver = {
+ .ops = &vt8237r_lpc_ops_r,
.vendor = PCI_VENDOR_ID_VIA,
.device = PCI_DEVICE_ID_VIA_VT8237R_LPC,
};
+
+static const struct pci_driver lpc_driver_s __pci_driver = {
+ .ops = &vt8237r_lpc_ops_s,
+ .vendor = PCI_VENDOR_ID_VIA,
+ .device = PCI_DEVICE_ID_VIA_VT8237S_LPC,
+};
diff --git a/src/southbridge/via/vt8237r/vt8237r_sata.c b/src/southbridge/via/vt8237r/vt8237r_sata.c
index ecdafdfd88..77d7b0c3e2 100644
--- a/src/southbridge/via/vt8237r/vt8237r_sata.c
+++ b/src/southbridge/via/vt8237r/vt8237r_sata.c
@@ -1,7 +1,7 @@
/*
* This file is part of the coreboot project.
*
- * Copyright (C) 2007 Rudolf Marek <r.marek@assembler.cz>
+ * Copyright (C) 2007, 2008 Rudolf Marek <r.marek@assembler.cz>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License v2 as published by
@@ -24,7 +24,7 @@
#define SATA_MISC_CTRL 0x45
-static void sata_init(struct device *dev)
+static void sata_i_init(struct device *dev)
{
u8 reg;
@@ -39,19 +39,82 @@ static void sata_init(struct device *dev)
pci_write_config8(dev, PCI_CLASS_DEVICE, 0x1);
reg |= 0x80; /* Sub Class Write Protect on */
pci_write_config8(dev, SATA_MISC_CTRL, reg);
+
+ return;
}
-static const struct device_operations sata_ops = {
+static void sata_ii_init(struct device *dev) {
+ u8 reg;
+
+ sata_i_init(dev);
+
+ /* analog black magic, you may or may not need to adjust 0x60-0x6f, depends on PCB */
+
+ /* Analog PHY - gen1
+ * CDR bandwidth [6:5] = 3
+ * Squelch Window Select [4:3] = 1
+ * CDR Charge Pump [2:0] = 1
+ */
+
+ pci_write_config8(dev, 0x64, 0x49);
+
+ /* adjust driver current source value to 9 */
+ reg = pci_read_config8(dev, 0x65);
+ reg &= 0xf0;
+ reg |= 0x9;
+ pci_write_config8(dev, 0x65, reg);
+
+ /* set all manual termination 50ohm bits [2:0] and enable [4] */
+ reg = pci_read_config8(dev, 0x6a);
+ reg |= 0xf;
+ pci_write_config8(dev, 0x6a, reg);
+
+ /* Analog PHY - gen2
+ * CDR bandwidth [5:4] = 2
+ * Pre / De-emphasis Level [7:6] controls bits [3:2], rest in 0x6e
+ * CDR Charge Pump [2:0] = 1
+ */
+
+ reg = pci_read_config8(dev, 0x6f);
+ reg &= 0x08;
+ reg |= 0x61;
+ pci_write_config8(dev, 0x6f, reg);
+
+ /* check if staggered spinup is supported */
+ reg = pci_read_config8(dev, 0x83);
+ if ((reg & 0x8) == 0) {
+ /* start OOB sequence on both drives */
+ reg |= 0x30;
+ pci_write_config8(dev, 0x83, reg);
+ }
+}
+
+static const struct device_operations sata_i_ops = {
.read_resources = pci_dev_read_resources,
.set_resources = pci_dev_set_resources,
.enable_resources = pci_dev_enable_resources,
- .init = sata_init,
+ .init = sata_i_init,
.enable = 0,
.ops_pci = 0,
};
-static const struct pci_driver northbridge_driver __pci_driver = {
- .ops = &sata_ops,
+static const struct device_operations sata_ii_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = sata_ii_init,
+ .enable = 0,
+ .ops_pci = 0,
+};
+
+static const struct pci_driver northbridge_driver_ii __pci_driver = {
+ .ops = &sata_ii_ops,
+ .vendor = PCI_VENDOR_ID_VIA,
+ .device = PCI_DEVICE_ID_VIA_VT8237_SATA,
+};
+
+static const struct pci_driver northbridge_driver_i __pci_driver = {
+ .ops = &sata_i_ops,
.vendor = PCI_VENDOR_ID_VIA,
.device = PCI_DEVICE_ID_VIA_VT6420_SATA,
};