soc/amd/stoneyridge: Move I2C bus clear out of gpio.c

Relocate the I2C bus reset code from gpio.c to i2c.c.  When it first
went in, gpio.c was a natural location due to the nature of the
algorithm.  This is preparation for moving most of gpio.c to common
code.

Change-Id: I3b2d8e1b54e7c5929220d763bd99fe01b0636aaa
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32650
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>

5 files changed, 149 insertions, 124 deletions

diff --git a/src/soc/amd/stoneyridge/chip.h b/src/soc/amd/stoneyridge/chip.h
index 92223d1962..d1a7d30199 100644
--- a/src/soc/amd/stoneyridge/chip.h
+++ b/src/soc/amd/stoneyridge/chip.h
@@ -20,7 +20,7 @@
 #include <stdint.h>
 #include <commonlib/helpers.h>
 #include <drivers/i2c/designware/dw_i2c.h>
-#include <soc/gpio.h>
+#include <soc/i2c.h>
 #include <arch/acpi_device.h>
 
 #define MAX_NODES 1
diff --git a/src/soc/amd/stoneyridge/gpio.c b/src/soc/amd/stoneyridge/gpio.c
index 01ced0880b..7c9680582c 100644
--- a/src/soc/amd/stoneyridge/gpio.c
+++ b/src/soc/amd/stoneyridge/gpio.c
@@ -18,11 +18,9 @@
 #include <device/mmio.h>
 #include <device/device.h>
 #include <console/console.h>
-#include <delay.h>
 #include <gpio.h>
 #include <amdblocks/acpimmio.h>
 #include <soc/gpio.h>
-#include <soc/pci_devs.h>
 #include <assert.h>
 #include "chip.h"
 
@@ -326,101 +324,6 @@ void sb_program_gpios(const struct soc_amd_gpio *gpio_list_ptr, size_t size)
 					edge_level, mask);
 }
 
-/*
- * I2C pins are open drain with external pull up, so in order to bit bang them
- * all, SCL pins must become GPIO inputs with no pull, then they need to be
- * toggled between input-no-pull and output-low. This table is for the initial
- * conversion of all SCL pins to input with no pull.
- */
-static const struct soc_amd_gpio i2c_2_gpi[] = {
-	PAD_GPI(I2C0_SCL_PIN, PULL_NONE),
-	PAD_GPI(I2C1_SCL_PIN, PULL_NONE),
-	PAD_GPI(I2C2_SCL_PIN, PULL_NONE),
-	PAD_GPI(I2C3_SCL_PIN, PULL_NONE),
-};
-#define saved_pins_count ARRAY_SIZE(i2c_2_gpi)
-
-/*
- * To program I2C pins without destroying their programming, the registers
- * that will be changed need to be saved first.
- */
-static void save_i2c_pin_registers(uint8_t gpio,
-					struct soc_amd_i2c_save *save_table)
-{
-	uint32_t *gpio_ptr;
-
-	gpio_ptr = (uint32_t *)gpio_get_address(gpio);
-	save_table->mux_value = iomux_read8(gpio);
-	save_table->control_value = read32(gpio_ptr);
-}
-
-static void restore_i2c_pin_registers(uint8_t gpio,
-					struct soc_amd_i2c_save *save_table)
-{
-	uint32_t *gpio_ptr;
-
-	gpio_ptr = (uint32_t *)gpio_get_address(gpio);
-	iomux_write8(gpio, save_table->mux_value);
-	iomux_read8(gpio);
-	write32(gpio_ptr, save_table->control_value);
-	read32(gpio_ptr);
-}
-
-/* Slaves to be reset are controlled by devicetree register i2c_scl_reset */
-void sb_reset_i2c_slaves(void)
-{
-	const struct soc_amd_stoneyridge_config *cfg;
-	const struct device *dev = pcidev_path_on_root(GNB_DEVFN);
-	struct soc_amd_i2c_save save_table[saved_pins_count];
-	uint8_t i, j, control;
-
-	if (!dev || !dev->chip_info)
-		return;
-	cfg = dev->chip_info;
-	control = cfg->i2c_scl_reset & GPIO_I2C_MASK;
-	if (control == 0)
-		return;
-
-	/* Save and reprogram I2C SCL pins */
-	for (i = 0; i < saved_pins_count; i++)
-		save_i2c_pin_registers(i2c_2_gpi[i].gpio, &save_table[i]);
-	sb_program_gpios(i2c_2_gpi, saved_pins_count);
-
-	/*
-	 * Toggle SCL back and forth 9 times under 100KHz. A single read is
-	 * needed after the writes to force the posted write to complete.
-	 */
-	for (j = 0; j < 9; j++) {
-		if (control & GPIO_I2C0_SCL)
-			write32((uint32_t *)GPIO_I2C0_ADDRESS, GPIO_SCL_LOW);
-		if (control & GPIO_I2C1_SCL)
-			write32((uint32_t *)GPIO_I2C1_ADDRESS, GPIO_SCL_LOW);
-		if (control & GPIO_I2C2_SCL)
-			write32((uint32_t *)GPIO_I2C2_ADDRESS, GPIO_SCL_LOW);
-		if (control & GPIO_I2C3_SCL)
-			write32((uint32_t *)GPIO_I2C3_ADDRESS, GPIO_SCL_LOW);
-
-		read32((uint32_t *)GPIO_I2C3_ADDRESS); /* Flush posted write */
-		udelay(4); /* 4usec gets 85KHz for 1 pin, 70KHz for 4 pins */
-
-		if (control & GPIO_I2C0_SCL)
-			write32((uint32_t *)GPIO_I2C0_ADDRESS, GPIO_SCL_HIGH);
-		if (control & GPIO_I2C1_SCL)
-			write32((uint32_t *)GPIO_I2C1_ADDRESS, GPIO_SCL_HIGH);
-		if (control & GPIO_I2C2_SCL)
-			write32((uint32_t *)GPIO_I2C2_ADDRESS, GPIO_SCL_HIGH);
-		if (control & GPIO_I2C3_SCL)
-			write32((uint32_t *)GPIO_I2C3_ADDRESS, GPIO_SCL_HIGH);
-
-		read32((uint32_t *)GPIO_I2C3_ADDRESS); /* Flush posted write */
-		udelay(4);
-	}
-
-	/* Restore I2C pins. */
-	for (i = 0; i < saved_pins_count; i++)
-		restore_i2c_pin_registers(i2c_2_gpi[i].gpio, &save_table[i]);
-}
-
 int gpio_interrupt_status(gpio_t gpio)
 {
 	uintptr_t gpio_address = gpio_get_address(gpio);
diff --git a/src/soc/amd/stoneyridge/i2c.c b/src/soc/amd/stoneyridge/i2c.c
index e99f3509ff..c3e5539e19 100644
--- a/src/soc/amd/stoneyridge/i2c.c
+++ b/src/soc/amd/stoneyridge/i2c.c
@@ -13,12 +13,16 @@
  * GNU General Public License for more details.
  */
 
+#include <device/mmio.h>
 #include <arch/acpi.h>
 #include <console/console.h>
+#include <delay.h>
 #include <drivers/i2c/designware/dw_i2c.h>
+#include <amdblocks/acpimmio.h>
 #include <soc/iomap.h>
 #include <soc/pci_devs.h>
 #include <soc/southbridge.h>
+#include <soc/i2c.h>
 #include "chip.h"
 
 #define I2C_BUS_ADDRESS(x) (I2C_BASE_ADDRESS + I2C_DEVICE_SIZE * (x))
@@ -140,3 +144,98 @@ struct device_operations stoneyridge_i2c_mmio_ops = {
 	.acpi_name = i2c_acpi_name,
 	.acpi_fill_ssdt_generator = dw_i2c_acpi_fill_ssdt,
 };
+
+/*
+ * I2C pins are open drain with external pull up, so in order to bit bang them
+ * all, SCL pins must become GPIO inputs with no pull, then they need to be
+ * toggled between input-no-pull and output-low. This table is for the initial
+ * conversion of all SCL pins to input with no pull.
+ */
+static const struct soc_amd_gpio i2c_2_gpi[] = {
+	PAD_GPI(I2C0_SCL_PIN, PULL_NONE),
+	PAD_GPI(I2C1_SCL_PIN, PULL_NONE),
+	PAD_GPI(I2C2_SCL_PIN, PULL_NONE),
+	PAD_GPI(I2C3_SCL_PIN, PULL_NONE),
+};
+#define saved_pins_count ARRAY_SIZE(i2c_2_gpi)
+
+/*
+ * To program I2C pins without destroying their programming, the registers
+ * that will be changed need to be saved first.
+ */
+static void save_i2c_pin_registers(uint8_t gpio,
+					struct soc_amd_i2c_save *save_table)
+{
+	uint32_t *gpio_ptr;
+
+	gpio_ptr = (uint32_t *)gpio_get_address(gpio);
+	save_table->mux_value = iomux_read8(gpio);
+	save_table->control_value = read32(gpio_ptr);
+}
+
+static void restore_i2c_pin_registers(uint8_t gpio,
+					struct soc_amd_i2c_save *save_table)
+{
+	uint32_t *gpio_ptr;
+
+	gpio_ptr = (uint32_t *)gpio_get_address(gpio);
+	iomux_write8(gpio, save_table->mux_value);
+	iomux_read8(gpio);
+	write32(gpio_ptr, save_table->control_value);
+	read32(gpio_ptr);
+}
+
+/* Slaves to be reset are controlled by devicetree register i2c_scl_reset */
+void sb_reset_i2c_slaves(void)
+{
+	const struct soc_amd_stoneyridge_config *cfg;
+	const struct device *dev = pcidev_path_on_root(GNB_DEVFN);
+	struct soc_amd_i2c_save save_table[saved_pins_count];
+	uint8_t i, j, control;
+
+	if (!dev || !dev->chip_info)
+		return;
+	cfg = dev->chip_info;
+	control = cfg->i2c_scl_reset & GPIO_I2C_MASK;
+	if (control == 0)
+		return;
+
+	/* Save and reprogram I2C SCL pins */
+	for (i = 0; i < saved_pins_count; i++)
+		save_i2c_pin_registers(i2c_2_gpi[i].gpio, &save_table[i]);
+	sb_program_gpios(i2c_2_gpi, saved_pins_count);
+
+	/*
+	 * Toggle SCL back and forth 9 times under 100KHz. A single read is
+	 * needed after the writes to force the posted write to complete.
+	 */
+	for (j = 0; j < 9; j++) {
+		if (control & GPIO_I2C0_SCL)
+			write32((uint32_t *)GPIO_I2C0_ADDRESS, GPIO_SCL_LOW);
+		if (control & GPIO_I2C1_SCL)
+			write32((uint32_t *)GPIO_I2C1_ADDRESS, GPIO_SCL_LOW);
+		if (control & GPIO_I2C2_SCL)
+			write32((uint32_t *)GPIO_I2C2_ADDRESS, GPIO_SCL_LOW);
+		if (control & GPIO_I2C3_SCL)
+			write32((uint32_t *)GPIO_I2C3_ADDRESS, GPIO_SCL_LOW);
+
+		read32((uint32_t *)GPIO_I2C3_ADDRESS); /* Flush posted write */
+		udelay(4); /* 4usec gets 85KHz for 1 pin, 70KHz for 4 pins */
+
+		if (control & GPIO_I2C0_SCL)
+			write32((uint32_t *)GPIO_I2C0_ADDRESS, GPIO_SCL_HIGH);
+		if (control & GPIO_I2C1_SCL)
+			write32((uint32_t *)GPIO_I2C1_ADDRESS, GPIO_SCL_HIGH);
+		if (control & GPIO_I2C2_SCL)
+			write32((uint32_t *)GPIO_I2C2_ADDRESS, GPIO_SCL_HIGH);
+		if (control & GPIO_I2C3_SCL)
+			write32((uint32_t *)GPIO_I2C3_ADDRESS, GPIO_SCL_HIGH);
+
+		read32((uint32_t *)GPIO_I2C3_ADDRESS); /* Flush posted write */
+		udelay(4);
+	}
+
+	/* Restore I2C pins. */
+	for (i = 0; i < saved_pins_count; i++)
+		restore_i2c_pin_registers(i2c_2_gpi[i].gpio, &save_table[i]);
+}
diff --git a/src/soc/amd/stoneyridge/include/soc/gpio.h b/src/soc/amd/stoneyridge/include/soc/gpio.h
index fe8240fb11..26d0336d0a 100644
--- a/src/soc/amd/stoneyridge/include/soc/gpio.h
+++ b/src/soc/amd/stoneyridge/include/soc/gpio.h
@@ -36,21 +36,10 @@ struct soc_amd_event {
 	uint8_t event;
 };
 
-struct soc_amd_i2c_save {
-	uint32_t control_value;
-	uint8_t mux_value;
-};
-
 #define GPIO_MASTER_SWITCH	0xFC
 #define   GPIO_MASK_STS_EN	BIT(28)
 #define   GPIO_INTERRUPT_EN	BIT(30)
 
-#define GPIO_I2C0_SCL		BIT(0)
-#define GPIO_I2C1_SCL		BIT(1)
-#define GPIO_I2C2_SCL		BIT(2)
-#define GPIO_I2C3_SCL		BIT(3)
-#define GPIO_I2C_MASK		(BIT(0) | BIT(1) | BIT(2) | BIT(3))
-
 #define GPIO_TOTAL_PINS		149
 #define GPIO_PIN_IN		(1 << 0)	/* for byte access */
 #define GPIO_PIN_OUT		(1 << 6)	/* for byte access */
@@ -186,15 +175,6 @@ struct soc_amd_i2c_save {
 #define GPIO_147			147
 #define GPIO_148			148
 
-#define I2C0_SCL_PIN			GPIO_145
-#define I2C1_SCL_PIN			GPIO_147
-#define I2C2_SCL_PIN			GPIO_113
-#define I2C3_SCL_PIN			GPIO_19
-
-#define GPIO_I2C0_ADDRESS		GPIO_BANK2_CONTROL(I2C0_SCL_PIN)
-#define GPIO_I2C1_ADDRESS		GPIO_BANK2_CONTROL(I2C1_SCL_PIN)
-#define GPIO_I2C2_ADDRESS		GPIO_BANK1_CONTROL(I2C2_SCL_PIN)
-#define GPIO_I2C3_ADDRESS		GPIO_BANK0_CONTROL(I2C3_SCL_PIN)
 #define GPIO_SCL_HIGH			0
 #define GPIO_SCL_LOW			GPIO_OUTPUT_ENABLE
 
@@ -373,11 +353,6 @@ struct soc_amd_i2c_save {
 #define GPIO_148_IOMUX_I2C1_SDA 0
 #define GPIO_148_IOMUX_GPIOxx 1
 
-#define I2C0_SCL_PIN_IOMUX_GPIOxx	GPIO_145_IOMUX_GPIOxx
-#define I2C1_SCL_PIN_IOMUX_GPIOxx	GPIO_147_IOMUX_GPIOxx
-#define I2C2_SCL_PIN_IOMUX_GPIOxx	GPIO_113_IOMUX_GPIOxx
-#define I2C3_SCL_PIN_IOMUX_GPIOxx	GPIO_19_IOMUX_GPIOxx
-
 enum {
 	GEVENT_0,
 	GEVENT_1,
@@ -599,7 +574,6 @@ uintptr_t gpio_get_address(gpio_t gpio_num);
  * @return none
  */
 void sb_program_gpios(const struct soc_amd_gpio *gpio_list_ptr, size_t size);
-void sb_reset_i2c_slaves(void);
 
 /* Return the interrupt status and clear if set. */
 int gpio_interrupt_status(gpio_t gpio);
diff --git a/src/soc/amd/stoneyridge/include/soc/i2c.h b/src/soc/amd/stoneyridge/include/soc/i2c.h
new file mode 100644
index 0000000000..62575d0fb8
--- /dev/null
+++ b/src/soc/amd/stoneyridge/include/soc/i2c.h
@@ -0,0 +1,49 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2018 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __STONEYRIDGE_I2C_H__
+#define __STONEYRIDGE_I2C_H__
+
+#include <soc/gpio.h>
+
+struct soc_amd_i2c_save {
+	uint32_t control_value;
+	uint8_t mux_value;
+};
+
+#define GPIO_I2C0_SCL			BIT(0)
+#define GPIO_I2C1_SCL			BIT(1)
+#define GPIO_I2C2_SCL			BIT(2)
+#define GPIO_I2C3_SCL			BIT(3)
+#define GPIO_I2C_MASK			(BIT(0) | BIT(1) | BIT(2) | BIT(3))
+
+#define I2C0_SCL_PIN			GPIO_145
+#define I2C1_SCL_PIN			GPIO_147
+#define I2C2_SCL_PIN			GPIO_113
+#define I2C3_SCL_PIN			GPIO_19
+
+#define GPIO_I2C0_ADDRESS		GPIO_BANK2_CONTROL(I2C0_SCL_PIN)
+#define GPIO_I2C1_ADDRESS		GPIO_BANK2_CONTROL(I2C1_SCL_PIN)
+#define GPIO_I2C2_ADDRESS		GPIO_BANK1_CONTROL(I2C2_SCL_PIN)
+#define GPIO_I2C3_ADDRESS		GPIO_BANK0_CONTROL(I2C3_SCL_PIN)
+
+#define I2C0_SCL_PIN_IOMUX_GPIOxx	GPIO_145_IOMUX_GPIOxx
+#define I2C1_SCL_PIN_IOMUX_GPIOxx	GPIO_147_IOMUX_GPIOxx
+#define I2C2_SCL_PIN_IOMUX_GPIOxx	GPIO_113_IOMUX_GPIOxx
+#define I2C3_SCL_PIN_IOMUX_GPIOxx	GPIO_19_IOMUX_GPIOxx
+
+void sb_reset_i2c_slaves(void);
+
+#endif /* __STONEYRIDGE_I2C_H__ */