summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--src/mainboard/asus/kgpe-d16/Kconfig1
-rw-r--r--src/mainboard/asus/kgpe-d16/cmos.default1
-rw-r--r--src/mainboard/asus/kgpe-d16/cmos.layout5
-rw-r--r--src/mainboard/asus/kgpe-d16/romstage.c84
4 files changed, 86 insertions, 5 deletions
diff --git a/src/mainboard/asus/kgpe-d16/Kconfig b/src/mainboard/asus/kgpe-d16/Kconfig
index f47e6a1029..f5ff81cbb8 100644
--- a/src/mainboard/asus/kgpe-d16/Kconfig
+++ b/src/mainboard/asus/kgpe-d16/Kconfig
@@ -6,6 +6,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy
select DIMM_DDR3
select DIMM_REGISTERED
# select QRANK_DIMM_SUPPORT
+ select DIMM_VOLTAGE_SET_SUPPORT
select NORTHBRIDGE_AMD_AMDFAM10
select SOUTHBRIDGE_AMD_SR5650
select SOUTHBRIDGE_AMD_SB700
diff --git a/src/mainboard/asus/kgpe-d16/cmos.default b/src/mainboard/asus/kgpe-d16/cmos.default
index 38b2ddf40b..d84c4027d6 100644
--- a/src/mainboard/asus/kgpe-d16/cmos.default
+++ b/src/mainboard/asus/kgpe-d16/cmos.default
@@ -6,6 +6,7 @@ iommu = Disable
nmi = Disable
hypertransport_speed_limit = Auto
max_mem_clock = DDR3-1600
+minimum_memory_voltage = 1.5V
ECC_memory = Enable
ECC_redirection = Disable
ecc_scrub_rate = 1.28us
diff --git a/src/mainboard/asus/kgpe-d16/cmos.layout b/src/mainboard/asus/kgpe-d16/cmos.layout
index 412051507f..c672e099cd 100644
--- a/src/mainboard/asus/kgpe-d16/cmos.layout
+++ b/src/mainboard/asus/kgpe-d16/cmos.layout
@@ -37,6 +37,7 @@ entries
456 1 e 1 ECC_memory
457 1 e 1 ECC_redirection
458 4 e 11 hypertransport_speed_limit
+462 2 e 12 minimum_memory_voltage
477 1 e 1 ieee1394_controller
728 256 h 0 user_data
984 16 h 0 check_sum
@@ -125,6 +126,10 @@ enumerations
11 13 400MHz
11 14 300MHz
11 15 200MHz
+12 0 1.5V
+12 1 1.35V
+12 2 1.25V
+12 3 1.15V
checksums
diff --git a/src/mainboard/asus/kgpe-d16/romstage.c b/src/mainboard/asus/kgpe-d16/romstage.c
index ddfdc08581..e5092684b1 100644
--- a/src/mainboard/asus/kgpe-d16/romstage.c
+++ b/src/mainboard/asus/kgpe-d16/romstage.c
@@ -131,7 +131,7 @@ static void activate_spd_rom(const struct mem_controller *ctrl) {
*/
static void set_ddr3_voltage(uint8_t node, uint8_t index) {
uint8_t byte;
- uint8_t value;
+ uint8_t value = 0;
if (index == 0)
value = 0x0;
@@ -157,6 +157,82 @@ static void set_ddr3_voltage(uint8_t node, uint8_t index) {
byte = pci_read_config8(PCI_DEV(0, 0x14, 3), 0xd0);
byte &= 0x0f;
pci_write_config8(PCI_DEV(0, 0x14, 3), 0xd0, byte);
+
+ printk(BIOS_DEBUG, "Node %02d DIMM voltage set to index %02x\n", node, index);
+}
+
+void DIMMSetVoltages(struct MCTStatStruc *pMCTstat,
+ struct DCTStatStruc *pDCTstatA) {
+ /* This mainboard allows the DIMM voltage to be set per-socket.
+ * Therefore, for each socket, iterate over all DIMMs to find the
+ * lowest supported voltage common to all DIMMs on that socket.
+ */
+ uint8_t nvram;
+ uint8_t dimm;
+ uint8_t node;
+ uint8_t socket;
+ uint8_t allowed_voltages = 0xf; /* The mainboard VRMs allow 1.15V, 1.25V, 1.35V, and 1.5V */
+ uint8_t node_allowed_voltages;
+ uint32_t set_voltage = 0;
+
+ if (get_option(&nvram, "minimum_memory_voltage") == CB_SUCCESS) {
+ switch (nvram) {
+ case 2:
+ allowed_voltages = 0x7; /* Allow 1.25V, 1.35V, and 1.5V */
+ break;
+ case 1:
+ allowed_voltages = 0x3; /* Allow 1.35V and 1.5V */
+ break;
+ case 0:
+ default:
+ allowed_voltages = 0x1; /* Allow 1.5V only */
+ break;
+ }
+ }
+
+ for (node = 0; node < MAX_NODES_SUPPORTED; node++) {
+ socket = node / 2;
+ node_allowed_voltages = allowed_voltages;
+ struct DCTStatStruc *pDCTstat;
+ pDCTstat = pDCTstatA + node;
+ if (pDCTstat->NodePresent) {
+ for (dimm = 0; dimm < MAX_DIMMS_SUPPORTED; dimm++) {
+ if (pDCTstat->DIMMValid & (1 << dimm)) {
+ node_allowed_voltages &= pDCTstat->DimmSupportedVoltages[dimm];
+ }
+ }
+ }
+
+ if (pDCTstat->NodePresent && (node % 2)) {
+ /* Set voltages */
+ if (node_allowed_voltages & 0x8) {
+ set_voltage = 1150;
+ set_ddr3_voltage(socket, 3);
+ } else if (node_allowed_voltages & 0x4) {
+ set_voltage = 1250;
+ set_ddr3_voltage(socket, 2);
+ } else if (node_allowed_voltages & 0x2) {
+ set_voltage = 1350;
+ set_ddr3_voltage(socket, 1);
+ } else {
+ set_voltage = 1500;
+ set_ddr3_voltage(socket, 0);
+ }
+
+ /* Save final DIMM voltages for SMBIOS use */
+ if (pDCTstat->NodePresent) {
+ for (dimm = 0; dimm < MAX_DIMMS_SUPPORTED; dimm++) {
+ pDCTstat->DimmConfiguredVoltage[dimm] = set_voltage;
+ }
+ }
+ pDCTstat = pDCTstatA + (node - 1);
+ if (pDCTstat->NodePresent) {
+ for (dimm = 0; dimm < MAX_DIMMS_SUPPORTED; dimm++) {
+ pDCTstat->DimmConfiguredVoltage[dimm] = set_voltage;
+ }
+ }
+ }
+ }
}
static void set_peripheral_control_lines(void) {
@@ -351,10 +427,8 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
die("After soft_reset_x - shouldn't see this message!!!\n");
}
- /* Set DDR memory voltage
- * FIXME
- * This should be set based on the output of the DIMM SPDs
- * For now it is locked to 1.5V
+ /* Set default DDR memory voltage
+ * This will be overridden later during RAM initialization
*/
set_lpc_sticky_ctl(1); /* Retain LPC/IMC GPIO configuration during S3 sleep */
if (!s3resume) { /* Avoid supply voltage glitches while the DIMMs are retaining data */