summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--src/include/cpu/amd/gx2def.h181
-rw-r--r--src/northbridge/amd/gx2/pll_reset.c117
2 files changed, 147 insertions, 151 deletions
diff --git a/src/include/cpu/amd/gx2def.h b/src/include/cpu/amd/gx2def.h
index b58569deb8..eaaeca4328 100644
--- a/src/include/cpu/amd/gx2def.h
+++ b/src/include/cpu/amd/gx2def.h
@@ -1,5 +1,6 @@
#ifndef CPU_AMD_GX2DEF_H
#define CPU_AMD_GX2DEF_H
+
#define CPU_ID_1_X 0x540 /* Stepping ID 1.x*/
#define CPU_ID_2_0 0x551 /* Stepping ID 2.0*/
#define CPU_ID_2_1 0x552 /* Stepping ID 2.1*/
@@ -13,6 +14,7 @@
#define CPU_REV_2_1 0x021
#define CPU_REV_2_2 0x022
#define CPU_REV_3_0 0x030
+
/* GeodeLink Control Processor Registers, GLIU1, Port 3 */
#define GLCP_CLK_DIS_DELAY 0x4c000008
#define GLCP_PMCLKDISABLE 0x4c000009
@@ -37,28 +39,27 @@
#define GLCP_SYS_RSTPLL_PCI_SEMI_SYNC_MODE 8
#define GLCP_SYS_RSTPLL_CHIP_RESET 0
-/* MSR routing as follows*/
-/* MSB = 1 means not for CPU*/
-/* next 3 bits 1st port*/
-/* next3 bits next port if through an GLIU*/
-/* etc...*/
+/* MSR routing as follows */
+/* MSB = 1 means not for CPU */
+/* next 3 bits 1st port */
+/* next3 bits next port if through an GLIU */
+/* etc... */
-/*Redcloud as follows.*/
+/* Redcloud as follows. */
/* GLIU0*/
-/* port0 - GLIU0*/
-/* port1 - MC*/
-/* port2 - GLIU1*/
-/* port3 - CPU*/
-/* port4 - VG*/
-/* port5 - GP*/
-/* port6 - DF*/
+/* port0 - GLIU0 */
+/* port1 - MC */
+/* port2 - GLIU1 */
+/* port3 - CPU */
+/* port4 - VG */
+/* port5 - GP */
+/* port6 - DF */
/* GLIU1*/
-/* port1 - GLIU0*/
-/* port3 - GLCP*/
-/* port4 - PCI*/
-/* port5 - FG*/
-
+/* port1 - GLIU0 */
+/* port3 - GLCP */
+/* port4 - PCI */
+/* port5 - FG */
#define GL0_GLIU0 0
#define GL0_MC 1
@@ -78,7 +79,7 @@
#define MSR_GLIU0 (GL0_GLIU0 << 29) + (1 << 28) /* 1000xxxx - To get on GeodeLink one bit has to be set */
#define MSR_MC (GL0_MC << 29) /* 2000xxxx */
#define MSR_GLIU1 (GL0_GLIU1 << 29) /* 4000xxxx */
-#define MSR_CPU (GL0_CPU << 29) /* 6000xxxx - this is not used for BIOS since code executing on CPU doesn't need to be routed*/
+#define MSR_CPU (GL0_CPU << 29) /* 6000xxxx - this is not used for BIOS since code executing on CPU doesn't need to be routed */
#define MSR_VG (GL0_VG << 29) /* 8000xxxx */
#define MSR_GP (GL0_GP << 29) /* A000xxxx */
#define MSR_DF (GL0_DF << 29) /* C000xxxx */
@@ -88,14 +89,11 @@
#define MSR_FG (GL1_FG << 26) + MSR_GLIU1 /* 5400xxxx */
#define MSR_VIP ((GL1_VIP << 26) + MSR_GLIU1) /* 5400xxxx */
#define MSR_AES ((GL1_AES << 26) + MSR_GLIU1) /* 5800xxxx */
-/* South Bridge*/
-#define SB_PORT 2 /* port of the SouthBridge */
-
-/**/
-/*GeodeLink Interface Unit 0 (GLIU0) port0*/
-/**/
+/* South Bridge */
+#define SB_PORT 2 /* port of the SouthBridge */
+/* GeodeLink Interface Unit 0 (GLIU0) port0 */
#define GLIU0_GLD_MSR_CAP (MSR_GLIU0 + 0x2000)
#define GLIU0_GLD_MSR_PM (MSR_GLIU0 + 0x2004)
@@ -103,10 +101,7 @@
#define GLIU0_CAP (MSR_GLIU0 + 0x86)
#define GLIU0_GLD_MSR_COH (MSR_GLIU0 + 0x80)
-
-/**/
-/* Memory Controller GLIU0 port 1*/
-/**/
+/* Memory Controller GLIU0 port 1 */
#define MC_GLD_MSR_CAP (MSR_MC + 0x2000)
#define MC_GLD_MSR_PM (MSR_MC + 0x2004)
@@ -129,7 +124,6 @@
#define CF07_LOWER_REF_TEST_SET (1 << 3)
#define CF07_LOWER_PROG_DRAM_SET (1 << 0)
-
#define MC_CF8F_DATA (MSR_MC + 0x19)
#define CF8F_UPPER_XOR_BS_SHIFT 19
@@ -164,19 +158,13 @@
#define MC_CF_RDSYNC (MSR_MC + 0x1F)
-
-/**/
-/* GLIU1 GLIU0 port2*/
-/**/
+/* GLIU1 GLIU0 port2 */
#define GLIU1_GLD_MSR_CAP (MSR_GLIU1 + 0x2000)
#define GLIU1_GLD_MSR_PM (MSR_GLIU1 + 0x2004)
#define GLIU1_GLD_MSR_COH (MSR_GLIU1 + 0x80)
-
-/**/
-/* CPU ; does not need routing instructions since we are executing there.*/
-/**/
+/* CPU ; does not need routing instructions since we are executing there. */
#define CPU_GLD_MSR_CAP 0x2000
#define CPU_GLD_MSR_CONFIG 0x2001
#define CPU_GLD_MSR_PM 0x2004
@@ -200,7 +188,7 @@
#define CPU_AC_MSR 0x1301
#define CPU_EX_BIST 0x1428
-/*IM*/
+/* IM */
#define CPU_IM_CONFIG 0x1700
#define IM_CONFIG_LOWER_ICD_SET (1 << 8)
#define IM_CONFIG_LOWER_QWT_SET (1 << 20)
@@ -215,13 +203,13 @@
#define CPU_IM_BIST_TAG 0x1730
#define CPU_IM_BIST_DATA 0x1731
-
/* various CPU MSRs */
#define CPU_DM_CONFIG0 0x1800
#define DM_CONFIG0_UPPER_WSREQ_SHIFT 12
#define DM_CONFIG0_LOWER_DCDIS_SET (1<<8)
#define DM_CONFIG0_LOWER_WBINVD_SET (1<<5)
#define DM_CONFIG0_LOWER_MISSER_SET (1<<1)
+
/* configuration MSRs */
#define CPU_RCONF_DEFAULT 0x1808
#define RCONF_DEFAULT_UPPER_ROMRC_SHIFT 24
@@ -276,7 +264,7 @@
#define CPU_L2TB_ENTRY 0x189E
#define CPU_L2TB_ENTRY_I 0x189F
#define CPU_DM_BIST 0x18C0
- /* SMM*/
+ /* SMM */
#define CPU_AC_SMM_CTL 0x1301
#define SMM_NMI_EN_SET (1<<0)
#define SMM_SUSP_EN_SET (1<<1)
@@ -294,10 +282,7 @@
#define TSC_SUSP_SET (1<<5)
#define SUSP_EN_SET (1<<12)
- /**/
- /* VG GLIU0 port4*/
- /**/
-
+/* VG GLIU0 port4 */
#define VG_GLD_MSR_CAP (MSR_VG + 0x2000)
#define VG_GLD_MSR_CONFIG (MSR_VG + 0x2001)
#define VG_GLD_MSR_PM (MSR_VG + 0x2004)
@@ -306,29 +291,20 @@
#define GP_GLD_MSR_CONFIG (MSR_GP + 0x2001)
#define GP_GLD_MSR_PM (MSR_GP + 0x2004)
-
-
-/**/
-/* DF GLIU0 port6*/
-/**/
-
+/* DF GLIU0 port6 */
#define DF_GLD_MSR_CAP (MSR_DF + 0x2000)
#define DF_GLD_MSR_MASTER_CONF (MSR_DF + 0x2001)
#define DF_LOWER_LCD_SHIFT 6
#define DF_GLD_MSR_PM (MSR_DF + 0x2004)
-
-
-/**/
-/* GeodeLink Control Processor GLIU1 port3*/
-/**/
+/* GeodeLink Control Processor GLIU1 port3 */
#define GLCP_GLD_MSR_CAP (MSR_GLCP + 0x2000)
#define GLCP_GLD_MSR_CONF (MSR_GLCP + 0x2001)
#define GLCP_GLD_MSR_PM (MSR_GLCP + 0x2004)
#define GLCP_DELAY_CONTROLS (MSR_GLCP + 0x0F)
-#define GLCP_SYS_RSTPLL (MSR_GLCP +0x14 /* R/W*/)
+#define GLCP_SYS_RSTPLL (MSR_GLCP +0x14 /* R/W */)
#define RSTPLL_UPPER_MDIV_SHIFT 9
#define RSTPLL_UPPER_VDIV_SHIFT 6
#define RSTPLL_UPPER_FBDIV_SHIFT 0
@@ -352,13 +328,10 @@
#define RSTPPL_LOWER_PCI_SEMI_SYNC_SET (1<<8)
#define RSTPPL_LOWER_CHIP_RESET_SET (1<<0)
-#define GLCP_DOTPLL (MSR_GLCP + 0x15 /* R/W*/)
+#define GLCP_DOTPLL (MSR_GLCP + 0x15 /* R/W */)
#define DOTPPL_LOWER_PD_SET (1<<14)
-
-/**/
-/* GLIU1 port 4*/
-/**/
+/* GLIU1 port 4 */
#define GLPCI_GLD_MSR_CAP (MSR_PCI + 0x2000)
#define GLPCI_GLD_MSR_CONFIG (MSR_PCI + 0x2001)
#define GLPCI_GLD_MSR_PM (MSR_PCI + 0x2004)
@@ -423,64 +396,60 @@
#define GLPCI_SPARE_LOWER_NSE_SET (1<<1)
#define GLPCI_SPARE_LOWER_SUPO_SET (1<<0)
-
-/**/
-/* FooGlue GLIU1 port 5*/
-/**/
+/* FooGlue GLIU1 port 5 */
#define FG_GLD_MSR_CAP (MSR_FG + 0x2000)
#define FG_GLD_MSR_PM (MSR_FG + 0x2004)
-/* VIP GLIU1 port 5*/
-/* */
+/* VIP GLIU1 port 5 */
#define VIP_GLD_MSR_CAP (MSR_VIP + 0x2000)
#define VIP_GLD_MSR_CONFIG (MSR_VIP + 0x2001)
#define VIP_GLD_MSR_PM (MSR_VIP + 0x2004)
#define VIP_BIST (MSR_VIP + 0x2005)
#define VIP_GIO_MSR_SEL (MSR_VIP + 0x2010)
-/* */
-/* AES GLIU1 port 6*/
-/* */
+
+/* AES GLIU1 port 6 */
#define AES_GLD_MSR_CAP (MSR_AES + 0x2000)
#define AES_GLD_MSR_CONFIG (MSR_AES + 0x2001)
#define AES_GLD_MSR_PM (MSR_AES + 0x2004)
#define AES_CONTROL (MSR_AES + 0x2006)
+
/* more fun stuff */
-#define BM 1 /* Base Mask - map power of 2 size aligned region*/
-#define BMO 2 /* BM with an offset*/
-#define R 3 /* Range - 4k range minimum*/
-#define RO 4 /* R with offset*/
-#define SC 5 /* Swiss 0xCeese - maps a 256K region in to 16K 0xcunks. Set W/R*/
-#define BMIO 6 /* Base Mask IO*/
-#define SCIO 7 /* Swiss 0xCeese IO*/
-#define SC_SHADOW 8 /* Special marker for Shadow SC descriptors so setShadow proc is independant of CPU*/
-#define R_SYSMEM 9 /* Special marker for SYSMEM R descriptors so GLIUInit proc is independant of CPU*/
-#define BMO_SMM 10 /* Specail marker for SMM*/
-#define BM_SMM 11 /* Specail marker for SMM*/
-#define BMO_DMM 12 /* Specail marker for DMM*/
-#define BM_DMM 13 /* Specail marker for DMM*/
-#define RO_FB 14 /* special for Frame buffer.*/
-#define R_FB 15 /* special for FB.*/
-#define OTHER 0x0FE /* Special marker for other*/
-#define GL_END 0x0FF /* end*/
+#define BM 1 /* Base Mask - map power of 2 size aligned region */
+#define BMO 2 /* BM with an offset */
+#define R 3 /* Range - 4k range minimum */
+#define RO 4 /* R with offset */
+#define SC 5 /* Swiss 0xCeese - maps a 256K region in to 16K 0xcunks. Set W/R */
+#define BMIO 6 /* Base Mask IO */
+#define SCIO 7 /* Swiss 0xCeese IO */
+#define SC_SHADOW 8 /* Special marker for Shadow SC descriptors so setShadow proc is independant of CPU */
+#define R_SYSMEM 9 /* Special marker for SYSMEM R descriptors so GLIUInit proc is independant of CPU */
+#define BMO_SMM 10 /* Specail marker for SMM */
+#define BM_SMM 11 /* Specail marker for SMM */
+#define BMO_DMM 12 /* Specail marker for DMM */
+#define BM_DMM 13 /* Specail marker for DMM */
+#define RO_FB 14 /* special for Frame buffer. */
+#define R_FB 15 /* special for FB. */
+#define OTHER 0x0FE /* Special marker for other */
+#define GL_END 0x0FF /* end */
#define MSR_GL0 (GL1_GLIU0 << 29)
-/* Set up desc addresses from 20 - 3f*/
-/* This is chip specific!*/
-#define MSR_GLIU0_BASE1 (MSR_GLIU0 + 0x20) /* BM*/
-#define MSR_GLIU0_BASE2 (MSR_GLIU0 + 0x21) /* BM*/
-#define MSR_GLIU0_SHADOW (MSR_GLIU0 + 0x2C) /* SCO should only be SC*/
-#define MSR_GLIU0_SYSMEM (MSR_GLIU0 + 0x28) /* RO should only be R*/
-#define MSR_GLIU0_SMM (MSR_GLIU0 + 0x26) /* BMO*/
-#define MSR_GLIU0_DMM (MSR_GLIU0 + 0x27) /* BMO*/
-
-#define MSR_GLIU1_BASE1 (MSR_GLIU1 + 0x20) /* BM*/
-#define MSR_GLIU1_BASE2 (MSR_GLIU1 + 0x21) /* BM*/
-#define MSR_GLIU1_SHADOW (MSR_GLIU1 + 0x2D) /* SCO should only be SC*/
-#define MSR_GLIU1_SYSMEM (MSR_GLIU1 + 0x29) /* RO should only be R*/
-#define MSR_GLIU1_SMM (MSR_GLIU1 + 0x23) /* BM*/
-#define MSR_GLIU1_DMM (MSR_GLIU1 + 0x24) /* BM*/
-#define MSR_GLIU1_FPU_TRAP (MSR_GLIU1 + 0x0E3) /* FooGlue F0 for FPU*/
+/* Set up desc addresses from 20 - 3f */
+/* This is chip specific! */
+#define MSR_GLIU0_BASE1 (MSR_GLIU0 + 0x20) /* BM */
+#define MSR_GLIU0_BASE2 (MSR_GLIU0 + 0x21) /* BM */
+#define MSR_GLIU0_SHADOW (MSR_GLIU0 + 0x2C) /* SCO should only be SC */
+#define MSR_GLIU0_SYSMEM (MSR_GLIU0 + 0x28) /* RO should only be R */
+#define MSR_GLIU0_SMM (MSR_GLIU0 + 0x26) /* BMO */
+#define MSR_GLIU0_DMM (MSR_GLIU0 + 0x27) /* BMO */
+
+#define MSR_GLIU1_BASE1 (MSR_GLIU1 + 0x20) /* BM */
+#define MSR_GLIU1_BASE2 (MSR_GLIU1 + 0x21) /* BM */
+#define MSR_GLIU1_SHADOW (MSR_GLIU1 + 0x2D) /* SCO should only be SC */
+#define MSR_GLIU1_SYSMEM (MSR_GLIU1 + 0x29) /* RO should only be R */
+#define MSR_GLIU1_SMM (MSR_GLIU1 + 0x23) /* BM */
+#define MSR_GLIU1_DMM (MSR_GLIU1 + 0x24) /* BM */
+#define MSR_GLIU1_FPU_TRAP (MSR_GLIU1 + 0x0E3) /* FooGlue F0 for FPU */
/* definitions that are "once you are mostly up, start VSA" type things */
#define SMM_OFFSET 0x40400000
@@ -503,9 +472,7 @@
#define CHIPSET_DEV_NUM 15
#define IDSEL_BASE 11 // bit 11 = device 1
-/* */
-/* SB LBAR IO + MEMORY MAP*/
-/* */
+/* SB LBAR IO + MEMORY MAP */
#define SMBUS_BASE ( 0x6000)
#define GPIO_BASE ( 0x6100)
#define MFGPT_BASE ( 0x6200)
diff --git a/src/northbridge/amd/gx2/pll_reset.c b/src/northbridge/amd/gx2/pll_reset.c
index a434307035..19b0946346 100644
--- a/src/northbridge/amd/gx2/pll_reset.c
+++ b/src/northbridge/amd/gx2/pll_reset.c
@@ -1,3 +1,23 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 Advanced Micro Devices, Inc.
+ * Copyright (C) 2010 Nils Jacobs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
#include <cpu/x86/tsc.h>
#define CLOCK_TICK_RATE 1193180U /* Underlying HZ */
@@ -69,7 +89,7 @@ bad_ctc:
/* spll_raw_clk = SYSREF * FbDIV,
* GLIU Clock = spll_raw_clk / MDIV
- * CPU Clock = sppl_raw_clk / VDIV
+ * CPU Clock = spll_raw_clk / VDIV
*/
/* table for Feedback divisor to FbDiv register value */
@@ -99,6 +119,15 @@ static const unsigned char pci33_ddr_crt [] = {
26, 2, 3 // 433/289
};
+/* FbDIV VDIV MDIV CPU/GeodeLink */
+/* 12 2 3 200/133 */
+/* 16 2 3 266/177 */
+/* 18 2 3 300/200 */
+/* 20 2 3 333/222 */
+/* 22 2 3 366/244 */
+/* 24 2 3 400/266 */
+/* 26 2 3 433/289 */
+
#if 0
static unsigned int get_memory_speed(void)
{
@@ -118,12 +147,12 @@ static unsigned int get_memory_speed(void)
///////////////////////////////////////////////////////////////////////////////
// Goodrich Version of pll_reset
-// PLLCHECK_COMPLETED is the "we've already done this" flag
+/* PLLCHECK_COMPLETED is the "we've already done this" flag */
#define PLLCHECK_COMPLETED (1 << RSTPLL_LOWER_SWFLAGS_SHIFT)
#ifndef RSTPPL_LOWER_BYPASS_SET
#define RSTPPL_LOWER_BYPASS_SET (1 << GLCP_SYS_RSTPLL_BYPASS)
-#endif // RSTPPL_LOWER_BYPASS_SET
+#endif /* RSTPPL_LOWER_BYPASS_SET */
#define DEFAULT_MDIV 3
#define DEFAULT_VDIV 2
@@ -133,84 +162,84 @@ static void pll_reset(void)
{
msr_t msrGlcpSysRstpll;
unsigned MDIV_VDIV_FBDIV;
- unsigned SyncBits; // store the sync bits in up ebx
+ unsigned SyncBits; /* store the sync bits in up ebx */
- // clear the Bypass bit
+ /* clear the Bypass bit */
- // If the straps say we are in bypass and the syspll is not AND there are no software
- // bits set then FS2 or something set up the PLL and we should not change it.
+ /* If the straps say we are in bypass and the syspll is not AND there are no software */
+ /* bits set then FS2 or something set up the PLL and we should not change it. */
msrGlcpSysRstpll = rdmsr(GLCP_SYS_RSTPLL);
msrGlcpSysRstpll.lo &= ~RSTPPL_LOWER_BYPASS_SET;
wrmsr(GLCP_SYS_RSTPLL, msrGlcpSysRstpll);
- // If the "we've already been here" flag is set, don't reconfigure the pll
+ /* If the "we've already been here" flag is set, don't reconfigure the pll */
if ( !(msrGlcpSysRstpll.lo & PLLCHECK_COMPLETED ) )
- { // we haven't configured the PLL; do it now
+ { /* we haven't configured the PLL; do it now */
- // Store PCI33(0)/66(1), SDR(0)/DDR(1), and CRT(0)/TFT(1) in upper esi to get to the
- // correct Strap Table.
+ /* Store PCI33(0)/66(1), SDR(0)/DDR(1), and CRT(0)/TFT(1) in upper esi to get to the */
+ /* correct Strap Table. */
post_code(POST_PLL_INIT);
- // configure for DDR
+ /* configure for DDR */
msrGlcpSysRstpll.lo &= ~(1 << RSTPPL_LOWER_SDRMODE_SHIFT);
wrmsr(GLCP_SYS_RSTPLL, msrGlcpSysRstpll);
- // Use Manual settings
- // UseManual:
+ /* Use Manual settings */
+ /* UseManual: */
post_code(POST_PLL_MANUAL);
- // DIV settings manually entered.
- // ax = VDIV, upper eax = MDIV, upper ecx = FbDIV
- // use gs and fs since we don't need them.
+ /* DIV settings manually entered. */
+ /* ax = VDIV, upper eax = MDIV, upper ecx = FbDIV */
+ /* use gs and fs since we don't need them. */
- // ProgramClocks:
- // ax = VDIV, upper eax = MDIV, upper ecx = FbDIV
- // move everything into ebx
- // VDIV
+ /* ProgramClocks: */
+ /* ax = VDIV, upper eax = MDIV, upper ecx = FbDIV */
+ /* move everything into ebx */
+ /* VDIV */
MDIV_VDIV_FBDIV = ((DEFAULT_VDIV - 2) << RSTPLL_UPPER_VDIV_SHIFT);
- // MDIV
+ /* MDIV */
MDIV_VDIV_FBDIV |= ((DEFAULT_MDIV - 2) << RSTPLL_UPPER_MDIV_SHIFT);
- // FbDIV
+ /* FbDIV */
MDIV_VDIV_FBDIV |= (plldiv2fbdiv[DEFAULT_FBDIV] << RSTPLL_UPPER_FBDIV_SHIFT);
- // write GLCP_SYS_RSTPPL (GLCP reg 0x14) with clock values
+ /* write GLCP_SYS_RSTPPL (GLCP reg 0x14) with clock values */
msrGlcpSysRstpll.lo &= ~(1 << RSTPPL_LOWER_SDRMODE_SHIFT);
wrmsr(GLCP_SYS_RSTPLL, msrGlcpSysRstpll);
msrGlcpSysRstpll.hi = MDIV_VDIV_FBDIV;
wrmsr(GLCP_SYS_RSTPLL, msrGlcpSysRstpll);
- // Set Reset, LockWait, and SW flag
- // DoReset:
+ /* Set Reset, LockWait, and SW flag */
+ /* DoReset: */
- // CheckSemiSync proc
- // Check for Semi-Sync in GeodeLink and CPU.
- // We need to do this here since the strap settings don't account for these bits.
+ /* CheckSemiSync proc */
+ /* Check for Semi-Sync in GeodeLink and CPU. */
+ /* We need to do this here since the strap settings don't account for these bits. */
SyncBits = 0; // store the sync bits in up ebx
- // Check for Bypass mode.
+ /* Check for Bypass mode. */
if (msrGlcpSysRstpll.lo & RSTPPL_LOWER_BYPASS_SET)
{
- // If we are in BYPASS PCI may or may not be sync'd but CPU and GeodeLink will.
+ /* If we are in BYPASS PCI may or may not be sync'd but CPU and GeodeLink will. */
SyncBits |= RSTPPL_LOWER_CPU_SEMI_SYNC_SET;
}
else
{
- // CheckPCIsync:
- // If FBdiv/Mdiv is evenly divisible then set the PCI semi-sync. FB is always greater
- // look up the real divider... if we get a 0 we have serious problems
+ /* CheckPCIsync: */
+ /* If FBdiv/Mdiv is evenly divisible then set the PCI semi-sync. FB is always greater */
+ /* look up the real divider... if we get a 0 we have serious problems */
if ( !(fbdiv2plldiv[((msrGlcpSysRstpll.hi >> RSTPLL_UPPER_FBDIV_SHIFT) & 0x3f)] %
(((msrGlcpSysRstpll.hi >> RSTPLL_UPPER_MDIV_SHIFT) & 0x0F) + 2)) )
{
SyncBits |= RSTPPL_LOWER_PCI_SEMI_SYNC_SET;
}
- // CheckCPUSync:
- // If Vdiv/Mdiv is evenly divisible then set the CPU semi-sync.
- // CPU is always greater or equal.
+ /* CheckCPUSync: */
+ /* If Vdiv/Mdiv is evenly divisible then set the CPU semi-sync. */
+ /* CPU is always greater or equal. */
if (!((((msrGlcpSysRstpll.hi >> RSTPLL_UPPER_MDIV_SHIFT) & 0x07) + 2) %
(((msrGlcpSysRstpll.hi >> RSTPLL_UPPER_VDIV_SHIFT) & 0x0F) + 2)))
{
@@ -219,29 +248,29 @@ static void pll_reset(void)
}
- // SetSync:
+ /* SetSync: */
msrGlcpSysRstpll.lo &= ~(RSTPPL_LOWER_PCI_SEMI_SYNC_SET | RSTPPL_LOWER_CPU_SEMI_SYNC_SET);
msrGlcpSysRstpll.lo |= SyncBits;
wrmsr(GLCP_SYS_RSTPLL, msrGlcpSysRstpll);
- // CheckSemiSync endp
+ /* CheckSemiSync endp */
- // now we do the reset
- // Set hold count to 99 (063h)
+ /* now we do the reset */
+ /* Set hold count to 99 (063h) */
msrGlcpSysRstpll.lo &= ~(0x0FF << RSTPPL_LOWER_HOLD_COUNT_SHIFT);
msrGlcpSysRstpll.lo |= (0x0DE << RSTPPL_LOWER_HOLD_COUNT_SHIFT);
msrGlcpSysRstpll.lo |= PLLCHECK_COMPLETED; // Say we are done
wrmsr(GLCP_SYS_RSTPLL, msrGlcpSysRstpll);
- // Don't want to use LOCKWAIT
+ /* Don't want to use LOCKWAIT */
msrGlcpSysRstpll.lo |= (RSTPPL_LOWER_PLL_RESET_SET + RSTPPL_LOWER_PD_SET);
msrGlcpSysRstpll.lo |= RSTPPL_LOWER_CHIP_RESET_SET;
wrmsr(GLCP_SYS_RSTPLL, msrGlcpSysRstpll);
- // You should never get here..... The chip has reset.
+ /* You should never get here..... The chip has reset. */
post_code(POST_PLL_RESET_FAIL);
while (1);
- } // we haven't configured the PLL; do it now
+ } /* we haven't configured the PLL; do it now */
}
// End of Goodrich version of pll_reset