summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--src/soc/amd/stoneyridge/Makefile.inc2
-rw-r--r--src/soc/amd/stoneyridge/early_setup.c258
-rw-r--r--src/soc/amd/stoneyridge/southbridge.c247
3 files changed, 249 insertions, 258 deletions
diff --git a/src/soc/amd/stoneyridge/Makefile.inc b/src/soc/amd/stoneyridge/Makefile.inc
index b62581cbb4..1b41292f7f 100644
--- a/src/soc/amd/stoneyridge/Makefile.inc
+++ b/src/soc/amd/stoneyridge/Makefile.inc
@@ -45,6 +45,7 @@ bootblock-y += pmutil.c
bootblock-y += reset.c
bootblock-y += sb_util.c
bootblock-y += tsc_freq.c
+bootblock-y += southbridge.c
romstage-y += BiosCallOuts.c
romstage-y += romstage.c
@@ -60,6 +61,7 @@ romstage-y += smbus_spd.c
romstage-y += ramtop.c
romstage-$(CONFIG_STONEYRIDGE_UART) += uart.c
romstage-y += tsc_freq.c
+romstage-y += southbridge.c
verstage-y += sb_util.c
verstage-y += pmutil.c
diff --git a/src/soc/amd/stoneyridge/early_setup.c b/src/soc/amd/stoneyridge/early_setup.c
index ec3baa4d8b..09eb8b6aa3 100644
--- a/src/soc/amd/stoneyridge/early_setup.c
+++ b/src/soc/amd/stoneyridge/early_setup.c
@@ -27,98 +27,6 @@
#include <cpu/x86/msr.h>
#include <delay.h>
-void configure_stoneyridge_uart(void)
-{
- u8 byte, byte2;
-
- if (CONFIG_UART_FOR_CONSOLE < 0 || CONFIG_UART_FOR_CONSOLE > 1)
- return;
-
- /* Power on the UART and AMBA devices */
- byte = read8((void *)ACPI_MMIO_BASE + AOAC_BASE + FCH_AOAC_REG56
- + CONFIG_UART_FOR_CONSOLE * 2);
- byte |= AOAC_PWR_ON_DEV;
- write8((void *)ACPI_MMIO_BASE + AOAC_BASE + FCH_AOAC_REG56
- + CONFIG_UART_FOR_CONSOLE * 2, byte);
-
- byte = read8((void *)ACPI_MMIO_BASE + AOAC_BASE + FCH_AOAC_REG62);
- byte |= AOAC_PWR_ON_DEV;
- write8((void *)ACPI_MMIO_BASE + AOAC_BASE + FCH_AOAC_REG62, byte);
-
- /* Set the GPIO mux to UART */
- write8((void *)FCH_IOMUXx89_UART0_RTS_L_EGPIO137, 0);
- write8((void *)FCH_IOMUXx8A_UART0_TXD_EGPIO138, 0);
- write8((void *)FCH_IOMUXx8E_UART1_RTS_L_EGPIO142, 0);
- write8((void *)FCH_IOMUXx8F_UART1_TXD_EGPIO143, 0);
-
- /* Wait for the UART and AMBA devices to indicate power and clock OK */
- do {
- udelay(100);
- byte = read8((void *)ACPI_MMIO_BASE + AOAC_BASE + FCH_AOAC_REG57
- + CONFIG_UART_FOR_CONSOLE * 2);
- byte &= (A0AC_PWR_RST_STATE | AOAC_RST_CLK_OK_STATE);
- byte2 = read8((void *)ACPI_MMIO_BASE + AOAC_BASE
- + FCH_AOAC_REG63);
- byte2 &= (A0AC_PWR_RST_STATE | AOAC_RST_CLK_OK_STATE);
- } while (!((byte == (A0AC_PWR_RST_STATE | AOAC_RST_CLK_OK_STATE)) &&
- (byte2 == (A0AC_PWR_RST_STATE | AOAC_RST_CLK_OK_STATE))));
-
-}
-
-void sb_pci_port80(void)
-{
- u8 byte;
- pci_devfn_t dev;
-
- dev = PCI_DEV(0, PCU_DEV, LPC_FUNC);
-
- byte = pci_read_config8(dev, LPC_IO_OR_MEM_DEC_EN_HIGH);
- byte &= ~DECODE_IO_PORT_ENABLE4_H; /* disable lpc port 80 */
- pci_write_config8(dev, LPC_IO_OR_MEM_DEC_EN_HIGH, byte);
-}
-
-void sb_lpc_port80(void)
-{
- u8 byte;
- pci_devfn_t dev;
-
- /* Enable LPC controller */
- outb(PM_LPC_GATING, PM_INDEX);
- byte = inb(PM_DATA);
- byte |= PM_LPC_ENABLE;
- outb(PM_LPC_GATING, PM_INDEX);
- outb(byte, PM_DATA);
-
- /* Enable port 80 LPC decode in pci function 3 configuration space. */
- dev = PCI_DEV(0, PCU_DEV, LPC_FUNC);
- byte = pci_read_config8(dev, LPC_IO_OR_MEM_DEC_EN_HIGH);
- byte |= DECODE_IO_PORT_ENABLE4_H; /* enable port 80 */
- pci_write_config8(dev, LPC_IO_OR_MEM_DEC_EN_HIGH, byte);
-}
-
-void sb_lpc_decode(void)
-{
- pci_devfn_t dev;
- u32 tmp = 0;
-
- /* Enable I/O decode to LPC bus */
- dev = PCI_DEV(0, PCU_DEV, LPC_FUNC);
- tmp = DECODE_ENABLE_PARALLEL_PORT0 | DECODE_ENABLE_PARALLEL_PORT2
- | DECODE_ENABLE_PARALLEL_PORT4 | DECODE_ENABLE_SERIAL_PORT0
- | DECODE_ENABLE_SERIAL_PORT1 | DECODE_ENABLE_SERIAL_PORT2
- | DECODE_ENABLE_SERIAL_PORT3 | DECODE_ENABLE_SERIAL_PORT4
- | DECODE_ENABLE_SERIAL_PORT5 | DECODE_ENABLE_SERIAL_PORT6
- | DECODE_ENABLE_SERIAL_PORT7 | DECODE_ENABLE_AUDIO_PORT0
- | DECODE_ENABLE_AUDIO_PORT1 | DECODE_ENABLE_AUDIO_PORT2
- | DECODE_ENABLE_AUDIO_PORT3 | DECODE_ENABLE_MSS_PORT2
- | DECODE_ENABLE_MSS_PORT3 | DECODE_ENABLE_FDC_PORT0
- | DECODE_ENABLE_FDC_PORT1 | DECODE_ENABLE_GAME_PORT
- | DECODE_ENABLE_KBC_PORT | DECODE_ENABLE_ACPIUC_PORT
- | DECODE_ENABLE_ADLIB_PORT;
-
- pci_write_config32(dev, LPC_IO_PORT_DECODE_ENABLE, tmp);
-}
-
static void enable_wideio(uint8_t port, uint16_t size)
{
uint32_t wideio_enable[] = {
@@ -205,169 +113,3 @@ void lpc_wideio_16_window(uint16_t base)
assert(IS_ALIGNED(base, 16));
lpc_wideio_window(base, 16);
}
-
-int s3_save_nvram_early(u32 dword, int size, int nvram_pos)
-{
- int i;
- printk(BIOS_DEBUG, "Writing %x of size %d to nvram pos: %d\n",
- dword, size, nvram_pos);
-
- for (i = 0; i < size; i++) {
- outb(nvram_pos, BIOSRAM_INDEX);
- outb((dword >> (8 * i)) & 0xff, BIOSRAM_DATA);
- nvram_pos++;
- }
-
- return nvram_pos;
-}
-
-int s3_load_nvram_early(int size, u32 *old_dword, int nvram_pos)
-{
- u32 data = *old_dword;
- int i;
- for (i = 0; i < size; i++) {
- outb(nvram_pos, BIOSRAM_INDEX);
- data &= ~(0xff << (i * 8));
- data |= inb(BIOSRAM_DATA) << (i * 8);
- nvram_pos++;
- }
- *old_dword = data;
- printk(BIOS_DEBUG, "Loading %x of size %d to nvram pos:%d\n",
- *old_dword, size, nvram_pos-size);
- return nvram_pos;
-}
-
-void sb_clk_output_48Mhz(void)
-{
- u32 ctrl;
-
- /*
- * Enable the X14M_25M_48M_OSC pin and leaving it at it's default so
- * 48Mhz will be on ball AP13 (FT3b package)
- */
- ctrl = read32((void *)(ACPI_MMIO_BASE + MISC_BASE + FCH_MISC_REG40));
-
- /* clear the OSCOUT1_ClkOutputEnb to enable the 48 Mhz clock */
- ctrl &= ~FCH_MISC_REG40_OSCOUT1_EN;
- write32((void *)(ACPI_MMIO_BASE + MISC_BASE + FCH_MISC_REG40), ctrl);
-}
-
-static uintptr_t sb_spibase(void)
-{
- /* Make sure the base address is predictable */
- device_t dev = PCI_DEV(0, PCU_DEV, LPC_FUNC);
- u32 base, enables;
-
- base = pci_read_config32(dev, SPIROM_BASE_ADDRESS_REGISTER);
- enables = base & 0xf;
- base &= ~0x3f;
-
- if (!base) {
- base = SPI_BASE_ADDRESS;
- pci_write_config32(dev, SPIROM_BASE_ADDRESS_REGISTER, base
- | enables | SPI_ROM_ENABLE);
- /* PCI_COMMAND_MEMORY is read-only and enabled. */
- }
- return (uintptr_t)base;
-}
-
-void sb_set_spi100(u16 norm, u16 fast, u16 alt, u16 tpm)
-{
- uintptr_t base = sb_spibase();
- write16((void *)base + SPI100_SPEED_CONFIG,
- (norm << SPI_NORM_SPEED_NEW_SH) |
- (fast << SPI_FAST_SPEED_NEW_SH) |
- (alt << SPI_ALT_SPEED_NEW_SH) |
- (tpm << SPI_TPM_SPEED_NEW_SH));
- write16((void *)base + SPI100_ENABLE, SPI_USE_SPI100);
-}
-
-void sb_disable_4dw_burst(void)
-{
- uintptr_t base = sb_spibase();
- write16((void *)base + SPI100_HOST_PREF_CONFIG,
- read16((void *)base + SPI100_HOST_PREF_CONFIG)
- & ~SPI_RD4DW_EN_HOST);
-}
-
-void sb_set_readspeed(u16 norm, u16 fast)
-{
- uintptr_t base = sb_spibase();
- write16((void *)base + SPI_CNTRL1, (read16((void *)base + SPI_CNTRL1)
- & ~SPI_CNTRL1_SPEED_MASK)
- | (norm << SPI_NORM_SPEED_SH)
- | (fast << SPI_FAST_SPEED_SH));
-}
-
-void sb_read_mode(u32 mode)
-{
- uintptr_t base = sb_spibase();
- write32((void *)base + SPI_CNTRL0,
- (read32((void *)base + SPI_CNTRL0)
- & ~SPI_READ_MODE_MASK) | mode);
-}
-
-void sb_tpm_decode_spi(void)
-{
- device_t dev = PCI_DEV(0, PCU_DEV, LPC_FUNC); /* LPC device */
-
- u32 spibase = pci_read_config32(dev, SPIROM_BASE_ADDRESS_REGISTER);
- pci_write_config32(dev, SPIROM_BASE_ADDRESS_REGISTER, spibase
- | ROUTE_TPM_2_SPI);
-}
-
-/*
- * Enable 4MB (LPC) ROM access at 0xFFC00000 - 0xFFFFFFFF.
- *
- * Hardware should enable LPC ROM by pin straps. This function does not
- * handle the theoretically possible PCI ROM, FWH, or SPI ROM configurations.
- *
- * The southbridge power-on default is to map 512K ROM space.
- *
- */
-void sb_enable_rom(void)
-{
- u8 reg8;
- pci_devfn_t dev;
-
- dev = PCI_DEV(0, PCU_DEV, LPC_FUNC);
-
- /*
- * Decode variable LPC ROM address ranges 1 and 2.
- * Bits 3-4 are not defined in any publicly available datasheet
- */
- reg8 = pci_io_read_config8(dev, LPC_IO_OR_MEM_DECODE_ENABLE);
- reg8 |= (1 << 3) | (1 << 4);
- pci_io_write_config8(dev, LPC_IO_OR_MEM_DECODE_ENABLE, reg8);
-
- /*
- * LPC ROM address range 1:
- * Enable LPC ROM range mirroring start at 0x000e(0000).
- */
- pci_io_write_config16(dev, ROM_ADDRESS_RANGE1_START, 0x000e);
-
- /* Enable LPC ROM range mirroring end at 0x000f(ffff). */
- pci_io_write_config16(dev, ROM_ADDRESS_RANGE1_END, 0x000f);
-
- /*
- * LPC ROM address range 2:
- *
- * Enable LPC ROM range start at:
- * 0xfff8(0000): 512KB
- * 0xfff0(0000): 1MB
- * 0xffe0(0000): 2MB
- * 0xffc0(0000): 4MB
- */
- pci_io_write_config16(dev, ROM_ADDRESS_RANGE2_START, 0x10000
- - (CONFIG_COREBOOT_ROMSIZE_KB >> 6));
-
- /* Enable LPC ROM range end at 0xffff(ffff). */
- pci_io_write_config16(dev, ROM_ADDRESS_RANGE2_END, 0xffff);
-}
-
-void bootblock_fch_early_init(void)
-{
- sb_enable_rom();
- sb_lpc_port80();
- sb_lpc_decode();
-}
diff --git a/src/soc/amd/stoneyridge/southbridge.c b/src/soc/amd/stoneyridge/southbridge.c
index 600b064f2d..dbf27bc6b8 100644
--- a/src/soc/amd/stoneyridge/southbridge.c
+++ b/src/soc/amd/stoneyridge/southbridge.c
@@ -28,7 +28,254 @@
#include <soc/southbridge.h>
#include <soc/smi.h>
#include <fchec.h>
+#include <delay.h>
+#include <soc/pci_devs.h>
+void configure_stoneyridge_uart(void)
+{
+ u8 byte, byte2;
+
+ if (CONFIG_UART_FOR_CONSOLE < 0 || CONFIG_UART_FOR_CONSOLE > 1)
+ return;
+
+ /* Power on the UART and AMBA devices */
+ byte = read8((void *)ACPI_MMIO_BASE + AOAC_BASE + FCH_AOAC_REG56
+ + CONFIG_UART_FOR_CONSOLE * 2);
+ byte |= AOAC_PWR_ON_DEV;
+ write8((void *)ACPI_MMIO_BASE + AOAC_BASE + FCH_AOAC_REG56
+ + CONFIG_UART_FOR_CONSOLE * 2, byte);
+
+ byte = read8((void *)ACPI_MMIO_BASE + AOAC_BASE + FCH_AOAC_REG62);
+ byte |= AOAC_PWR_ON_DEV;
+ write8((void *)ACPI_MMIO_BASE + AOAC_BASE + FCH_AOAC_REG62, byte);
+
+ /* Set the GPIO mux to UART */
+ write8((void *)FCH_IOMUXx89_UART0_RTS_L_EGPIO137, 0);
+ write8((void *)FCH_IOMUXx8A_UART0_TXD_EGPIO138, 0);
+ write8((void *)FCH_IOMUXx8E_UART1_RTS_L_EGPIO142, 0);
+ write8((void *)FCH_IOMUXx8F_UART1_TXD_EGPIO143, 0);
+
+ /* Wait for the UART and AMBA devices to indicate power and clock OK */
+ do {
+ udelay(100);
+ byte = read8((void *)ACPI_MMIO_BASE + AOAC_BASE + FCH_AOAC_REG57
+ + CONFIG_UART_FOR_CONSOLE * 2);
+ byte &= (A0AC_PWR_RST_STATE | AOAC_RST_CLK_OK_STATE);
+ byte2 = read8((void *)ACPI_MMIO_BASE + AOAC_BASE
+ + FCH_AOAC_REG63);
+ byte2 &= (A0AC_PWR_RST_STATE | AOAC_RST_CLK_OK_STATE);
+ } while (!((byte == (A0AC_PWR_RST_STATE | AOAC_RST_CLK_OK_STATE)) &&
+ (byte2 == (A0AC_PWR_RST_STATE | AOAC_RST_CLK_OK_STATE))));
+
+}
+
+void sb_pci_port80(void)
+{
+ u8 byte;
+
+ byte = pci_read_config8(SOC_LPC_DEV, LPC_IO_OR_MEM_DEC_EN_HIGH);
+ byte &= ~DECODE_IO_PORT_ENABLE4_H; /* disable lpc port 80 */
+ pci_write_config8(SOC_LPC_DEV, LPC_IO_OR_MEM_DEC_EN_HIGH, byte);
+}
+
+void sb_lpc_port80(void)
+{
+ u8 byte;
+
+ /* Enable LPC controller */
+ outb(PM_LPC_GATING, PM_INDEX);
+ byte = inb(PM_DATA);
+ byte |= PM_LPC_ENABLE;
+ outb(PM_LPC_GATING, PM_INDEX);
+ outb(byte, PM_DATA);
+
+ /* Enable port 80 LPC decode in pci function 3 configuration space. */
+ byte = pci_read_config8(SOC_LPC_DEV, LPC_IO_OR_MEM_DEC_EN_HIGH);
+ byte |= DECODE_IO_PORT_ENABLE4_H; /* enable port 80 */
+ pci_write_config8(SOC_LPC_DEV, LPC_IO_OR_MEM_DEC_EN_HIGH, byte);
+}
+
+void sb_lpc_decode(void)
+{
+ u32 tmp = 0;
+
+ /* Enable I/O decode to LPC bus */
+ tmp = DECODE_ENABLE_PARALLEL_PORT0 | DECODE_ENABLE_PARALLEL_PORT2
+ | DECODE_ENABLE_PARALLEL_PORT4 | DECODE_ENABLE_SERIAL_PORT0
+ | DECODE_ENABLE_SERIAL_PORT1 | DECODE_ENABLE_SERIAL_PORT2
+ | DECODE_ENABLE_SERIAL_PORT3 | DECODE_ENABLE_SERIAL_PORT4
+ | DECODE_ENABLE_SERIAL_PORT5 | DECODE_ENABLE_SERIAL_PORT6
+ | DECODE_ENABLE_SERIAL_PORT7 | DECODE_ENABLE_AUDIO_PORT0
+ | DECODE_ENABLE_AUDIO_PORT1 | DECODE_ENABLE_AUDIO_PORT2
+ | DECODE_ENABLE_AUDIO_PORT3 | DECODE_ENABLE_MSS_PORT2
+ | DECODE_ENABLE_MSS_PORT3 | DECODE_ENABLE_FDC_PORT0
+ | DECODE_ENABLE_FDC_PORT1 | DECODE_ENABLE_GAME_PORT
+ | DECODE_ENABLE_KBC_PORT | DECODE_ENABLE_ACPIUC_PORT
+ | DECODE_ENABLE_ADLIB_PORT;
+
+ pci_write_config32(SOC_LPC_DEV, LPC_IO_PORT_DECODE_ENABLE, tmp);
+}
+
+void sb_clk_output_48Mhz(void)
+{
+ u32 ctrl;
+
+ /*
+ * Enable the X14M_25M_48M_OSC pin and leaving it at it's default so
+ * 48Mhz will be on ball AP13 (FT3b package)
+ */
+ ctrl = read32((void *)(ACPI_MMIO_BASE + MISC_BASE + FCH_MISC_REG40));
+
+ /* clear the OSCOUT1_ClkOutputEnb to enable the 48 Mhz clock */
+ ctrl &= ~FCH_MISC_REG40_OSCOUT1_EN;
+ write32((void *)(ACPI_MMIO_BASE + MISC_BASE + FCH_MISC_REG40), ctrl);
+}
+
+static uintptr_t sb_spibase(void)
+{
+ u32 base, enables;
+
+ /* Make sure the base address is predictable */
+ base = pci_read_config32(SOC_LPC_DEV, SPIROM_BASE_ADDRESS_REGISTER);
+ enables = base & 0xf;
+ base &= ~0x3f;
+
+ if (!base) {
+ base = SPI_BASE_ADDRESS;
+ pci_write_config32(SOC_LPC_DEV, SPIROM_BASE_ADDRESS_REGISTER,
+ base | enables | SPI_ROM_ENABLE);
+ /* PCI_COMMAND_MEMORY is read-only and enabled. */
+ }
+ return (uintptr_t)base;
+}
+
+void sb_set_spi100(u16 norm, u16 fast, u16 alt, u16 tpm)
+{
+ uintptr_t base = sb_spibase();
+ write16((void *)base + SPI100_SPEED_CONFIG,
+ (norm << SPI_NORM_SPEED_NEW_SH) |
+ (fast << SPI_FAST_SPEED_NEW_SH) |
+ (alt << SPI_ALT_SPEED_NEW_SH) |
+ (tpm << SPI_TPM_SPEED_NEW_SH));
+ write16((void *)base + SPI100_ENABLE, SPI_USE_SPI100);
+}
+
+void sb_disable_4dw_burst(void)
+{
+ uintptr_t base = sb_spibase();
+ write16((void *)base + SPI100_HOST_PREF_CONFIG,
+ read16((void *)base + SPI100_HOST_PREF_CONFIG)
+ & ~SPI_RD4DW_EN_HOST);
+}
+
+void sb_set_readspeed(u16 norm, u16 fast)
+{
+ uintptr_t base = sb_spibase();
+ write16((void *)base + SPI_CNTRL1, (read16((void *)base + SPI_CNTRL1)
+ & ~SPI_CNTRL1_SPEED_MASK)
+ | (norm << SPI_NORM_SPEED_SH)
+ | (fast << SPI_FAST_SPEED_SH));
+}
+
+void sb_read_mode(u32 mode)
+{
+ uintptr_t base = sb_spibase();
+ write32((void *)base + SPI_CNTRL0,
+ (read32((void *)base + SPI_CNTRL0)
+ & ~SPI_READ_MODE_MASK) | mode);
+}
+
+void sb_tpm_decode_spi(void)
+{
+ u32 spibase = pci_read_config32(SOC_LPC_DEV,
+ SPIROM_BASE_ADDRESS_REGISTER);
+ pci_write_config32(SOC_LPC_DEV, SPIROM_BASE_ADDRESS_REGISTER, spibase
+ | ROUTE_TPM_2_SPI);
+}
+
+/*
+ * Enable 4MB (LPC) ROM access at 0xFFC00000 - 0xFFFFFFFF.
+ *
+ * Hardware should enable LPC ROM by pin straps. This function does not
+ * handle the theoretically possible PCI ROM, FWH, or SPI ROM configurations.
+ *
+ * The southbridge power-on default is to map 512K ROM space.
+ *
+ */
+void sb_enable_rom(void)
+{
+ u8 reg8;
+
+ /*
+ * Decode variable LPC ROM address ranges 1 and 2.
+ * Bits 3-4 are not defined in any publicly available datasheet
+ */
+ reg8 = pci_read_config8(SOC_LPC_DEV, LPC_IO_OR_MEM_DECODE_ENABLE);
+ reg8 |= (1 << 3) | (1 << 4);
+ pci_write_config8(SOC_LPC_DEV, LPC_IO_OR_MEM_DECODE_ENABLE, reg8);
+
+ /*
+ * LPC ROM address range 1:
+ * Enable LPC ROM range mirroring start at 0x000e(0000).
+ */
+ pci_write_config16(SOC_LPC_DEV, ROM_ADDRESS_RANGE1_START, 0x000e);
+
+ /* Enable LPC ROM range mirroring end at 0x000f(ffff). */
+ pci_write_config16(SOC_LPC_DEV, ROM_ADDRESS_RANGE1_END, 0x000f);
+
+ /*
+ * LPC ROM address range 2:
+ *
+ * Enable LPC ROM range start at:
+ * 0xfff8(0000): 512KB
+ * 0xfff0(0000): 1MB
+ * 0xffe0(0000): 2MB
+ * 0xffc0(0000): 4MB
+ */
+ pci_write_config16(SOC_LPC_DEV, ROM_ADDRESS_RANGE2_START, 0x10000
+ - (CONFIG_COREBOOT_ROMSIZE_KB >> 6));
+
+ /* Enable LPC ROM range end at 0xffff(ffff). */
+ pci_write_config16(SOC_LPC_DEV, ROM_ADDRESS_RANGE2_END, 0xffff);
+}
+
+void bootblock_fch_early_init(void)
+{
+ sb_enable_rom();
+ sb_lpc_port80();
+ sb_lpc_decode();
+}
+
+int s3_save_nvram_early(u32 dword, int size, int nvram_pos)
+{
+ int i;
+ printk(BIOS_DEBUG, "Writing %x of size %d to nvram pos: %d\n",
+ dword, size, nvram_pos);
+
+ for (i = 0; i < size; i++) {
+ outb(nvram_pos, BIOSRAM_INDEX);
+ outb((dword >> (8 * i)) & 0xff, BIOSRAM_DATA);
+ nvram_pos++;
+ }
+
+ return nvram_pos;
+}
+
+int s3_load_nvram_early(int size, u32 *old_dword, int nvram_pos)
+{
+ u32 data = *old_dword;
+ int i;
+ for (i = 0; i < size; i++) {
+ outb(nvram_pos, BIOSRAM_INDEX);
+ data &= ~(0xff << (i * 8));
+ data |= inb(BIOSRAM_DATA) << (i * 8);
+ nvram_pos++;
+ }
+ *old_dword = data;
+ printk(BIOS_DEBUG, "Loading %x of size %d to nvram pos:%d\n",
+ *old_dword, size, nvram_pos-size);
+ return nvram_pos;
+}
int acpi_get_sleep_type(void)
{