summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--src/southbridge/intel/i82801dx/i82801dx.h19
-rw-r--r--src/southbridge/intel/i82801dx/i82801dx_lpc.c286
2 files changed, 178 insertions, 127 deletions
diff --git a/src/southbridge/intel/i82801dx/i82801dx.h b/src/southbridge/intel/i82801dx/i82801dx.h
index 070fb7e4a2..cb062bf1d4 100644
--- a/src/southbridge/intel/i82801dx/i82801dx.h
+++ b/src/southbridge/intel/i82801dx/i82801dx.h
@@ -36,6 +36,9 @@
extern void i82801dx_enable(device_t dev);
#endif
+#define IO_APIC_ADDR 0xfec00000
+#define HPET_ADDR 0xfed00000
+
#define DEBUG_PERIODIC_SMIS 0
#define MAINBOARD_POWER_OFF 0
@@ -79,8 +82,15 @@ extern void i82801dx_enable(device_t dev);
#define BIOS_CNTL 0x4E
#define GPIO_BASE 0x58
#define GPIO_CNTL 0x5C
-#define PIRQA_ROUT 0x60
-#define PIRQE_ROUT 0x68
+#define GPIOBASE_ADDR 0x0500
+#define PIRQA_ROUT 0x60
+#define PIRQB_ROUT 0x61
+#define PIRQC_ROUT 0x62
+#define PIRQD_ROUT 0x63
+#define PIRQE_ROUT 0x68
+#define PIRQF_ROUT 0x69
+#define PIRQG_ROUT 0x6A
+#define PIRQH_ROUT 0x6B
#define COM_DEC 0xE0
#define LPC_EN 0xE6
#define FUNC_DIS 0xF2
@@ -192,4 +202,9 @@ extern void i82801dx_enable(device_t dev);
#define TCOBASE 0x60 /* TCO Base Address Register */
#define TCO1_CNT 0x08 /* TCO1 Control Register */
+/* GEN_PMCON_3 bits */
+#define RTC_BATTERY_DEAD (1 << 2)
+#define RTC_POWER_FAILED (1 << 1)
+#define SLEEP_AFTER_POWER_FAIL (1 << 0)
+
#endif /* I82801DX_H */
diff --git a/src/southbridge/intel/i82801dx/i82801dx_lpc.c b/src/southbridge/intel/i82801dx/i82801dx_lpc.c
index 6c2ef3c573..99456bae9a 100644
--- a/src/southbridge/intel/i82801dx/i82801dx_lpc.c
+++ b/src/southbridge/intel/i82801dx/i82801dx_lpc.c
@@ -4,6 +4,7 @@
* Copyright (C) 2003 Linux Networx
* Copyright (C) 2004 SuSE Linux AG
* Copyright (C) 2004 Tyan Computer
+ * Copyright (C) 2010 Joseph Smith <joe@settoplinux.org>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
@@ -32,166 +33,201 @@
#define NMI_OFF 0
-void i82801dx_enable_ioapic(struct device *dev)
+typedef struct southbridge_intel_i82801dx_config config_t;
+
+static void i82801dx_enable_ioapic(struct device *dev)
{
- u32 dword;
- volatile u32 *ioapic_sba = (volatile u32 *)0xfec00000;
- volatile u32 *ioapic_sbd = (volatile u32 *)0xfec00010;
-
- dword = pci_read_config32(dev, GEN_CNTL);
- dword |= (3 << 7); /* enable ioapic */
- dword |= (1 << 13); /* coprocessor error enable */
- dword |= (1 << 1); /* delay transaction enable */
- dword |= (1 << 2); /* DMA collection buf enable */
- pci_write_config32(dev, GEN_CNTL, dword);
- printk_debug("ioapic southbridge enabled %x\n", dword);
- *ioapic_sba = 0;
- *ioapic_sbd = (2 << 24);
- //lyh *ioapic_sba=3;
- //lyh *ioapic_sbd=1;
- *ioapic_sba = 0;
- dword = *ioapic_sbd;
- printk_debug("Southbridge apic id = %x\n", dword);
- if (dword != (2 << 24))
- die("");
- //lyh *ioapic_sba=3;
- //lyh dword=*ioapic_sbd;
- //lyh printk_debug("Southbridge apic DT = %x\n",dword);
- //lyh if(dword!=1)
- //lyh die("");
+ u32 reg32;
+ volatile u32 *ioapic_index = (volatile u32 *)IO_APIC_ADDR;
+ volatile u32 *ioapic_data = (volatile u32 *)IO_APIC_ADDR + 0x10;
+
+ /* Set ACPI base address (I/O space). */
+ pci_write_config32(dev, PMBASE, (PMBASE_ADDR | 1));
+
+ /* Enable ACPI I/O and power management. */
+ pci_write_config8(dev, ACPI_CNTL, 0x10);
+ reg32 = pci_read_config32(dev, GEN_CNTL);
+ reg32 |= (3 << 7); /* Enable IOAPIC */
+ reg32 |= (1 << 13); /* Coprocessor error enable */
+ reg32 |= (1 << 1); /* Delayed transaction enable */
+ reg32 |= (1 << 2); /* DMA collection buffer enable */
+ pci_write_config32(dev, GEN_CNTL, reg32);
+ printk_debug("IOAPIC Southbridge enabled %x\n", reg32);
+
+ *ioapic_index = 0;
+ *ioapic_data = (1 << 25);
+
+ *ioapic_index = 0;
+ reg32 = *ioapic_data;
+ printk_debug("Southbridge APIC ID = %x\n", reg32);
+ if (reg32 != (1 << 25))
+ die("APIC Error\n");
+
+ /* TODO: From i82801ca, needed/useful on other ICH? */
+ *ioapic_index = 3; /* Select Boot Configuration register. */
+ *ioapic_data = 1; /* Use Processor System Bus to deliver interrupts. */
}
-void i82801dx_enable_serial_irqs(struct device *dev)
+static void i82801dx_enable_serial_irqs(struct device *dev)
{
+ /* Set packet length and toggle silent mode bit. */
pci_write_config8(dev, SERIRQ_CNTL,
(1 << 7) | (1 << 6) | ((21 - 17) << 2) | (0 << 0));
+ pci_write_config8(dev, SERIRQ_CNTL,
+ (1 << 7) | (0 << 6) | ((21 - 17) << 2) | (0 << 0));
}
-void i82801dx_lpc_route_dma(struct device *dev, u8 mask)
+static void i82801dx_pirq_init(device_t dev)
{
- u16 word;
- int i;
- word = pci_read_config16(dev, PCI_DMA_CFG);
- word &= ((1 << 10) - (1 << 8));
- for (i = 0; i < 8; i++) {
- if (i == 4)
- continue;
- word |= ((mask & (1 << i)) ? 3 : 1) << (i * 2);
- }
- pci_write_config16(dev, PCI_DMA_CFG, word);
+ /* Get the chip configuration */
+ config_t *config = dev->chip_info;
+
+ pci_write_config8(dev, PIRQA_ROUT, config->pirqa_routing);
+ pci_write_config8(dev, PIRQB_ROUT, config->pirqb_routing);
+ pci_write_config8(dev, PIRQC_ROUT, config->pirqc_routing);
+ pci_write_config8(dev, PIRQD_ROUT, config->pirqd_routing);
+ pci_write_config8(dev, PIRQE_ROUT, config->pirqe_routing);
+ pci_write_config8(dev, PIRQF_ROUT, config->pirqf_routing);
+ pci_write_config8(dev, PIRQG_ROUT, config->pirqg_routing);
+ pci_write_config8(dev, PIRQH_ROUT, config->pirqh_routing);
+
}
-void i82801dx_rtc_init(struct device *dev)
+static void i82801dx_power_options(device_t dev)
{
u8 byte;
- u32 dword;
- int rtc_failed;
- byte = pci_read_config8(dev, GEN_PMCON_3);
- rtc_failed = byte & RTC_FAILED;
- if (rtc_failed) {
- byte &= ~(1 << 1); /* preserve the power fail state */
- pci_write_config8(dev, GEN_PMCON_3, byte);
+ int pwr_on = -1;
+ int nmi_option;
+
+ /* power after power fail */
+ /* FIXME this doesn't work! */
+ /* Which state do we want to goto after g3 (power restored)?
+ * 0 == S0 Full On
+ * 1 == S5 Soft Off
+ */
+ pci_write_config8(dev, GEN_PMCON_3, pwr_on ? 0 : 1);
+ printk_info("Set power %s if power fails\n", pwr_on ? "on" : "off");
+
+ /* Set up NMI on errors. */
+ byte = inb(0x61);
+ byte &= ~(1 << 3); /* IOCHK# NMI Enable */
+ byte &= ~(1 << 2); /* PCI SERR# Enable */
+ outb(byte, 0x61);
+ byte = inb(0x70);
+
+ nmi_option = NMI_OFF;
+ get_option(&nmi_option, "nmi");
+ if (nmi_option) {
+ byte &= ~(1 << 7); /* Set NMI. */
+ outb(byte, 0x70);
}
- dword = pci_read_config32(dev, GEN_STS);
- rtc_failed |= dword & (1 << 2);
- rtc_init(rtc_failed);
}
-void i82801dx_1f0_misc(struct device *dev)
+static void gpio_init(device_t dev)
{
- pci_write_config16(dev, PCICMD, 0x014f);
- pci_write_config32(dev, PMBASE, 0x00001001);
- pci_write_config8(dev, ACPI_CNTL, 0x10);
- pci_write_config32(dev, GPIO_BASE, 0x00001181);
+ /* This should be done in romstage.c already */
+ pci_write_config32(dev, GPIO_BASE, (GPIOBASE_ADDR | 1));
pci_write_config8(dev, GPIO_CNTL, 0x10);
- pci_write_config32(dev, PIRQA_ROUT, 0x0A05030B);
- pci_write_config8(dev, PIRQE_ROUT, 0x07);
+}
+
+static void i82801dx_rtc_init(struct device *dev)
+{
+ u8 reg8;
+ u32 reg32;
+ int rtc_failed;
+
+ reg8 = pci_read_config8(dev, GEN_PMCON_3);
+ rtc_failed = reg8 & RTC_BATTERY_DEAD;
+ if (rtc_failed) {
+ reg8 &= ~(1 << 1); /* Preserve the power fail state. */
+ pci_write_config8(dev, GEN_PMCON_3, reg8);
+ }
+ reg32 = pci_read_config32(dev, GEN_STS);
+ rtc_failed |= reg32 & (1 << 2);
+ rtc_init(rtc_failed);
+
+ /* Enable access to the upper 128 byte bank of CMOS RAM. */
pci_write_config8(dev, RTC_CONF, 0x04);
- pci_write_config8(dev, COM_DEC, 0x10); //lyh E0->
- pci_write_config16(dev, LPC_EN, 0x000F); //LYH 000D->
}
-static void enable_hpet(struct device *dev)
+static void i82801dx_lpc_route_dma(struct device *dev, u8 mask)
{
- const unsigned long hpet_address = 0xfed00000;
+ u16 reg16;
+ int i;
- u32 dword;
- u32 code = (0 & 0x3);
+ reg16 = pci_read_config16(dev, PCI_DMA_CFG);
+ reg16 &= 0x300;
+ for (i = 0; i < 8; i++) {
+ if (i == 4)
+ continue;
+ reg16 |= ((mask & (1 << i)) ? 3 : 1) << (i * 2);
+ }
+ pci_write_config16(dev, PCI_DMA_CFG, reg16);
+}
- dword = pci_read_config32(dev, GEN_CNTL);
- dword |= (1 << 17); /* enable hpet */
- /*Bits [16:15]Memory Address Range
- 00 FED0_0000h - FED0_03FFh
- 01 FED0_1000h - FED0_13FFh
- 10 FED0_2000h - FED0_23FFh
- 11 FED0_3000h - FED0_33FFh */
+static void i82801dx_lpc_decode_en(device_t dev)
+{
+ /* Decode 0x3F8-0x3FF (COM1) for COMA port, 0x2F8-0x2FF (COM2) for COMB.
+ * LPT decode defaults to 0x378-0x37F and 0x778-0x77F.
+ * Floppy decode defaults to 0x3F0-0x3F5, 0x3F7.
+ * We also need to set the value for LPC I/F Enables Register.
+ */
+ pci_write_config8(dev, COM_DEC, 0x10);
+ pci_write_config16(dev, LPC_EN, 0x300F);
+}
- dword &= ~(3 << 15); /* clear it */
- dword |= (code << 15);
+static void enable_hpet(struct device *dev)
+{
+ u32 reg32;
+ u32 code = (0 & 0x3);
- printk_debug("enabling HPET @0x%lx\n", hpet_address | (code << 12));
+ reg32 = pci_read_config32(dev, GEN_CNTL);
+ reg32 |= (1 << 17); /* Enable HPET. */
+ /*
+ * Bits [16:15] Memory Address Range
+ * 00 FED0_0000h - FED0_03FFh
+ * 01 FED0_1000h - FED0_13FFh
+ * 10 FED0_2000h - FED0_23FFh
+ * 11 FED0_3000h - FED0_33FFh
+ */
+ reg32 &= ~(3 << 15); /* Clear it */
+ reg32 |= (code << 15);
+ /* TODO: reg32 is never written to anywhere? */
+ printk_debug("Enabling HPET @0x%x\n", HPET_ADDR | (code << 12));
}
static void lpc_init(struct device *dev)
{
- u8 byte;
- int pwr_on = -1;
- int nmi_option;
+ /* Set the value for PCI command register. */
+ pci_write_config16(dev, PCI_COMMAND, 0x000f);
- /* IO APIC initialization */
+ /* IO APIC initialization. */
i82801dx_enable_ioapic(dev);
i82801dx_enable_serial_irqs(dev);
-#ifdef SUSPICIOUS_LOOKING_CODE
- // The ICH-4 datasheet does not mention this configuration register.
- // This code may have been inherited (incorrectly) from code for the AMD 766 southbridge,
- // which *does* support this functionality.
+ /* Setup the PIRQ. */
+ i82801dx_pirq_init(dev);
- /* posted memory write enable */
- byte = pci_read_config8(dev, 0x46);
- pci_write_config8(dev, 0x46, byte | (1 << 0));
-#endif
+ /* Setup power options. */
+ i82801dx_power_options(dev);
- /* power after power fail */
- /* FIXME this doesn't work! */
- /* Which state do we want to goto after g3 (power restored)?
- * 0 == S0 Full On
- * 1 == S5 Soft Off
- */
- pci_write_config8(dev, GEN_PMCON_3, pwr_on ? 0 : 1);
- printk_info("set power %s after power fail\n", pwr_on ? "on" : "off");
-#if 0
- /* Enable Error reporting */
- /* Set up sync flood detected */
- byte = pci_read_config8(dev, 0x47);
- byte |= (1 << 1);
- pci_write_config8(dev, 0x47, byte);
-#endif
-
- /* Set up NMI on errors */
- byte = inb(0x61);
- byte &= ~(1 << 3); /* IOCHK# NMI Enable */
- byte &= ~(1 << 2); /* PCI SERR# Enable */
- outb(byte, 0x61);
- byte = inb(0x70);
- nmi_option = NMI_OFF;
- get_option(&nmi_option, "nmi");
- if (nmi_option) {
- byte &= ~(1 << 7); /* set NMI */
- outb(byte, 0x70);
- }
+ /* Set the state of the GPIO lines. */
+ gpio_init(dev);
- /* Initialize the real time clock */
+ /* Initialize the real time clock. */
i82801dx_rtc_init(dev);
+ /* Route DMA. */
i82801dx_lpc_route_dma(dev, 0xff);
- /* Initialize isa dma */
+ /* Initialize ISA DMA. */
isa_dma_init();
- i82801dx_1f0_misc(dev);
+ /* Setup decode ports and LPC I/F enables. */
+ i82801dx_lpc_decode_en(dev);
+
/* Initialize the High Precision Event Timers */
enable_hpet(dev);
}
@@ -208,15 +244,15 @@ static void i82801dx_lpc_read_resources(device_t dev)
res->base = 0;
res->size = 0x1000;
res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE |
- IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
res = new_resource(dev, IOINDEX_SUBTRACTIVE(1, 0));
res->base = 0xff800000;
- res->size = 0x00800000; /* 8 MB for flash */
+ res->size = 0x00800000; /* 8 MB for flash */
res->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE |
- IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
- res = new_resource(dev, 3); /* IOAPIC */
+ res = new_resource(dev, 3); /* IOAPIC */
res->base = 0xfec00000;
res->size = 0x00001000;
res->flags = IORESOURCE_MEM | IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
@@ -229,12 +265,12 @@ static void i82801dx_lpc_enable_resources(device_t dev)
}
static struct device_operations lpc_ops = {
- .read_resources = i82801dx_lpc_read_resources,
- .set_resources = pci_dev_set_resources,
- .enable_resources = i82801dx_lpc_enable_resources,
- .init = lpc_init,
- .scan_bus = scan_static_bus,
- .enable = i82801dx_enable,
+ .read_resources = i82801dx_lpc_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = i82801dx_lpc_enable_resources,
+ .init = lpc_init,
+ .scan_bus = scan_static_bus,
+ .enable = i82801dx_enable,
};
/* 82801DB/DBL */