diff options
| -rw-r--r-- | src/mainboard/google/hatch/Kconfig | 2 | ||||
| -rw-r--r-- | src/mainboard/google/hatch/variants/baseboard/devicetree.cb | 141 | ||||
| -rw-r--r-- | src/mainboard/google/hatch/variants/hatch/overridetree.cb | 123 | ||||
| -rw-r--r-- | src/mainboard/google/hatch/variants/hatch_whl/overridetree.cb | 126 |
4 files changed, 257 insertions, 135 deletions
diff --git a/src/mainboard/google/hatch/Kconfig b/src/mainboard/google/hatch/Kconfig index f57b41043f..041ac2d95e 100644 --- a/src/mainboard/google/hatch/Kconfig +++ b/src/mainboard/google/hatch/Kconfig @@ -85,7 +85,7 @@ config MAX_CPUS config OVERRIDE_DEVICETREE string - default "variants/$(CONFIG_VARIANT_DIR)/overridetree.cb" if !BOARD_GOOGLE_HATCH_WHL + default "variants/$(CONFIG_VARIANT_DIR)/overridetree.cb" config TPM_TIS_ACPI_INTERRUPT int diff --git a/src/mainboard/google/hatch/variants/baseboard/devicetree.cb b/src/mainboard/google/hatch/variants/baseboard/devicetree.cb index 007f297c39..2f1120a584 100644 --- a/src/mainboard/google/hatch/variants/baseboard/devicetree.cb +++ b/src/mainboard/google/hatch/variants/baseboard/devicetree.cb @@ -17,35 +17,6 @@ chip soc/intel/cannonlake # EC memory map range is 0x900-0x9ff register "gen3_dec" = "0x00fc0901" - # Intel Common SoC Config - #+-------------------+---------------------------+ - #| Field | Value | - #+-------------------+---------------------------+ - #| GSPI0 | cr50 TPM. Early init is | - #| | required to set up a BAR | - #| | for TPM communication | - #| | before memory is up | - #| GSPI1 | FP MCU | - #| I2C0 | Touchpad | - #| I2C1 | Touch screen | - #| I2C4 | Audio | - #+-------------------+---------------------------+ - register "common_soc_config" = "{ - .gspi[0] = { - .speed_mhz = 1, - .early_init = 1, - }, - .i2c[0] = { - .speed = I2C_SPEED_FAST, - }, - .i2c[1] = { - .speed = I2C_SPEED_FAST, - }, - .i2c[4] = { - .speed = I2C_SPEED_FAST, - }, - }" - # FSP configuration register "InternalGfx" = "1" register "SkipExtGfxScan" = "1" @@ -214,87 +185,11 @@ chip soc/intel/cannonlake register "wake" = "GPE0_PME_B0" device pci 14.3 on end # CNVi wifi end - device pci 14.5 on end # SDCard - device pci 15.0 on - chip drivers/i2c/generic - register "hid" = ""ELAN0000"" - register "desc" = ""ELAN Touchpad"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D21_IRQ)" - register "wake" = "GPE0_DW0_21" - device i2c 15 on end - end - end # I2C #0 - device pci 15.1 on - chip drivers/i2c/generic - register "hid" = ""ELAN0001"" - register "desc" = ""ELAN Touchscreen"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)" - register "probed" = "1" - register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" - register "reset_delay_ms" = "100" - register "reset_off_delay_ms" = "5" - register "has_power_resource" = "1" - register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C4)" - register "stop_off_delay_ms" = "5" - device i2c 49 on end - end - chip drivers/i2c/hid - register "generic.hid" = ""GDIX0000"" - register "generic.desc" = ""Goodix Touchscreen"" - register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)" - register "generic.probed" = "1" - register "generic.reset_gpio" = - "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" - register "generic.reset_delay_ms" = "30" - register "generic.reset_off_delay_ms" = "3" - register "generic.has_power_resource" = "1" - register "hid_desc_reg_offset" = "0x01" - device i2c 5d on end - end - end # I2C #1 - device pci 15.2 on - chip drivers/generic/gpio_keys - register "name" = ""PENH"" - register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_HIGH(GPP_A8)" - register "key.dev_name" = ""EJCT"" - register "key.linux_code" = "SW_PEN_INSERTED" - register "key.linux_input_type" = "EV_SW" - register "key.label" = ""pen_eject"" - device generic 0 on end - end - end # I2C #2 - device pci 15.3 on - chip drivers/i2c/sx9310 - register "desc" = ""SAR Proximity Sensor"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A0_IRQ)" - register "speed" = "I2C_SPEED_FAST" - register "uid" = "1" - register "reg_prox_ctrl0" = "0x10" - register "reg_prox_ctrl1" = "0x00" - register "reg_prox_ctrl2" = "0x84" - register "reg_prox_ctrl3" = "0x0e" - register "reg_prox_ctrl4" = "0x07" - register "reg_prox_ctrl5" = "0xc6" - register "reg_prox_ctrl6" = "0x20" - register "reg_prox_ctrl7" = "0x0d" - register "reg_prox_ctrl8" = "0x8d" - register "reg_prox_ctrl9" = "0x43" - register "reg_prox_ctrl10" = "0x1f" - register "reg_prox_ctrl11" = "0x00" - register "reg_prox_ctrl12" = "0x00" - register "reg_prox_ctrl13" = "0x00" - register "reg_prox_ctrl14" = "0x00" - register "reg_prox_ctrl15" = "0x00" - register "reg_prox_ctrl16" = "0x00" - register "reg_prox_ctrl17" = "0x00" - register "reg_prox_ctrl18" = "0x00" - register "reg_prox_ctrl19" = "0x00" - register "reg_sar_ctrl0" = "0x50" - register "reg_sar_ctrl1" = "0x8a" - register "reg_sar_ctrl2" = "0x3c" - device i2c 28 on end - end - end # I2C #3 + device pci 14.5 on end # SDCard + device pci 15.0 on end # I2C #0 + device pci 15.1 on end # I2C #1 + device pci 15.2 on end # I2C #2 + device pci 15.3 on end # I2C #3 device pci 16.0 on end # Management Engine Interface 1 device pci 16.1 off end # Management Engine Interface 2 device pci 16.2 off end # Management Engine IDE-R @@ -302,20 +197,7 @@ chip soc/intel/cannonlake device pci 16.4 off end # Management Engine Interface 3 device pci 16.5 off end # Management Engine Interface 4 device pci 17.0 on end # SATA - device pci 19.0 on - chip drivers/i2c/generic - register "hid" = ""10EC5682"" - register "name" = ""RT58"" - register "desc" = ""Realtek RT5682"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_H0_IRQ)" - register "property_count" = "1" - # Set the jd_src to RT5668_JD1 for jack detection - register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" - register "property_list[0].name" = ""realtek,jd-src"" - register "property_list[0].integer" = "1" - device i2c 1a on end - end - end #I2C #4 + device pci 19.0 on end #I2C #4 device pci 19.1 off end # I2C #5 device pci 19.2 off end # UART #2 device pci 1a.0 off end # eMMC @@ -348,16 +230,7 @@ chip soc/intel/cannonlake device spi 0 on end end end # GSPI #0 - device pci 1e.3 on - chip drivers/spi/acpi - register "name" = ""CRFP"" - register "hid" = "ACPI_DT_NAMESPACE_HID" - register "uid" = "1" - register "compat_string" = ""google,cros-ec-spi"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A23_IRQ)" - device spi 1 on end - end # FPMCU - end # GSPI #1 + device pci 1e.3 on end # GSPI #1 device pci 1f.0 on chip ec/google/chromeec device pnp 0c09.0 on end diff --git a/src/mainboard/google/hatch/variants/hatch/overridetree.cb b/src/mainboard/google/hatch/variants/hatch/overridetree.cb index 6e6414e8a8..28644d14cf 100644 --- a/src/mainboard/google/hatch/variants/hatch/overridetree.cb +++ b/src/mainboard/google/hatch/variants/hatch/overridetree.cb @@ -15,4 +15,127 @@ chip soc/intel/cannonlake [PchSerialIoIndexUART2] = PchSerialIoDisabled, }" + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| GSPI0 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| | before memory is up | + #| GSPI1 | FP MCU | + #| I2C0 | Touchpad | + #| I2C1 | Touch screen | + #| I2C4 | Audio | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .gspi[0] = { + .speed_mhz = 1, + .early_init = 1, + }, + .i2c[0] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[4] = { + .speed = I2C_SPEED_FAST, + }, + }" + + device domain 0 on + device pci 15.0 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D21_IRQ)" + register "wake" = "GPE0_DW0_21" + device i2c 15 on end + end + end # I2C #0 + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)" + register "probed" = "1" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" + register "reset_delay_ms" = "100" + register "reset_off_delay_ms" = "5" + register "has_power_resource" = "1" + register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C4)" + register "stop_off_delay_ms" = "5" + device i2c 49 on end + end + end # I2C #1 + device pci 15.2 on + chip drivers/generic/gpio_keys + register "name" = ""PENH"" + register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_HIGH(GPP_A8)" + register "key.dev_name" = ""EJCT"" + register "key.linux_code" = "SW_PEN_INSERTED" + register "key.linux_input_type" = "EV_SW" + register "key.label" = ""pen_eject"" + device generic 0 on end + end + end # I2C #2 + device pci 15.3 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A0_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "1" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C #3 + device pci 19.0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Realtek RT5682"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_H0_IRQ)" + register "property_count" = "1" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + end #I2C #4 + device pci 1e.3 on + chip drivers/spi/acpi + register "name" = ""CRFP"" + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "uid" = "1" + register "compat_string" = ""google,cros-ec-spi"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A23_IRQ)" + device spi 1 on end + end # FPMCU + end # GSPI #1 + end + end diff --git a/src/mainboard/google/hatch/variants/hatch_whl/overridetree.cb b/src/mainboard/google/hatch/variants/hatch_whl/overridetree.cb new file mode 100644 index 0000000000..9b772c2cd7 --- /dev/null +++ b/src/mainboard/google/hatch/variants/hatch_whl/overridetree.cb @@ -0,0 +1,126 @@ +chip soc/intel/cannonlake + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| GSPI0 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| | before memory is up | + #| GSPI1 | FP MCU | + #| I2C0 | Touchpad | + #| I2C1 | Touch screen | + #| I2C4 | Audio | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .gspi[0] = { + .speed_mhz = 1, + .early_init = 1, + }, + .i2c[0] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[4] = { + .speed = I2C_SPEED_FAST, + }, + }" + + device domain 0 on + device pci 15.0 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D21_IRQ)" + register "wake" = "GPE0_DW0_21" + device i2c 15 on end + end + end # I2C #0 + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D16_IRQ)" + register "probed" = "1" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" + register "reset_delay_ms" = "100" + register "reset_off_delay_ms" = "5" + register "has_power_resource" = "1" + register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C4)" + register "stop_off_delay_ms" = "5" + device i2c 49 on end + end + end # I2C #1 + device pci 15.2 on + chip drivers/generic/gpio_keys + register "name" = ""PENH"" + register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_HIGH(GPP_A8)" + register "key.dev_name" = ""EJCT"" + register "key.linux_code" = "SW_PEN_INSERTED" + register "key.linux_input_type" = "EV_SW" + register "key.label" = ""pen_eject"" + device generic 0 on end + end + end # I2C #2 + device pci 15.3 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A0_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "1" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C #3 + device pci 19.0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Realtek RT5682"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_H0_IRQ)" + register "property_count" = "1" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + end #I2C #4 + device pci 1e.3 on + chip drivers/spi/acpi + register "name" = ""CRFP"" + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "uid" = "1" + register "compat_string" = ""google,cros-ec-spi"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A23_IRQ)" + device spi 1 on end + end # FPMCU + end # GSPI #1 + end + +end |