summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--src/mainboard/msi/ms9185/Config.lb299
-rw-r--r--src/mainboard/msi/ms9185/Options.lb332
-rw-r--r--src/mainboard/msi/ms9185/cache_as_ram_auto.c375
-rw-r--r--src/mainboard/msi/ms9185/chip.h28
-rw-r--r--src/mainboard/msi/ms9185/cmos.layout98
-rw-r--r--src/mainboard/msi/ms9185/get_bus_conf.c144
-rw-r--r--src/mainboard/msi/ms9185/irq_tables.c126
-rw-r--r--src/mainboard/msi/ms9185/mainboard.c33
-rw-r--r--src/mainboard/msi/ms9185/mb_sysconf.h40
-rw-r--r--src/mainboard/msi/ms9185/mptable.c205
-rw-r--r--src/mainboard/msi/ms9185/resourcemap.c291
-rw-r--r--src/southbridge/broadcom/bcm5785/bcm5785_sata.c17
-rw-r--r--targets/msi/ms9185/Config.lb94
13 files changed, 2082 insertions, 0 deletions
diff --git a/src/mainboard/msi/ms9185/Config.lb b/src/mainboard/msi/ms9185/Config.lb
new file mode 100644
index 0000000000..34c48d1f5f
--- /dev/null
+++ b/src/mainboard/msi/ms9185/Config.lb
@@ -0,0 +1,299 @@
+##
+## This file is part of the LinuxBIOS project.
+##
+## Copyright (C) 2006 AMD
+## Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
+##
+## Copyright (C) 2006 MSI
+## Written by bxshi <bingxunshi@gmail.com> for MSI.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+##
+## Compute the location and size of where this firmware image
+## (linuxBIOS plus bootloader) will live in the boot rom chip.
+##
+if USE_FALLBACK_IMAGE
+ default ROM_SECTION_SIZE = FALLBACK_SIZE
+ default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE )
+else
+ default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE )
+ default ROM_SECTION_OFFSET = 0
+end
+
+##
+## Compute the start location and size size of
+## The linuxBIOS bootloader.
+##
+default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+
+##
+## Compute where this copy of linuxBIOS will start in the boot rom
+##
+default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up linuxBIOS,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+default XIP_ROM_SIZE=65536
+default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
+
+arch i386 end
+
+##
+## Build the objects we have code for in this directory.
+##
+
+driver mainboard.o
+
+#dir /drivers/si/3114
+
+#needed by irq_tables and mptable and acpi_tables
+object get_bus_conf.o
+
+if HAVE_MP_TABLE
+ object mptable.o
+end
+
+if HAVE_PIRQ_TABLE
+ object irq_tables.o
+end
+
+if USE_DCACHE_RAM
+
+ if CONFIG_USE_INIT
+ # compile cache_as_ram.c to auto.o
+ makerule ./cache_as_ram_auto.o
+ depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o $@"
+ end
+
+ else
+ #compile cache_as_ram.c to auto.inc
+ makerule ./cache_as_ram_auto.inc
+ depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@"
+ action "perl -e 's/.rodata/.rom.data/g' -pi $@"
+ action "perl -e 's/.text/.section .rom.text/g' -pi $@"
+ end
+
+ end
+end
+##
+## Build our 16 bit and 32 bit linuxBIOS entry code
+##
+
+if USE_FALLBACK_IMAGE
+ mainboardinit cpu/x86/16bit/entry16.inc
+ ldscript /cpu/x86/16bit/entry16.lds
+end
+
+mainboardinit cpu/x86/32bit/entry32.inc
+if USE_DCACHE_RAM
+ if CONFIG_USE_INIT
+ ldscript /cpu/x86/32bit/entry32.lds
+ end
+
+ if CONFIG_USE_INIT
+ ldscript /cpu/amd/car/cache_as_ram.lds
+ end
+end
+
+##
+## Build our reset vector (This is where linuxBIOS is entered)
+##
+if USE_FALLBACK_IMAGE
+ mainboardinit cpu/x86/16bit/reset16.inc
+ ldscript /cpu/x86/16bit/reset16.lds
+else
+ mainboardinit cpu/x86/32bit/reset32.inc
+ ldscript /cpu/x86/32bit/reset32.lds
+end
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+
+if USE_DCACHE_RAM
+ ##
+ ## Setup Cache-As-Ram
+ ##
+ mainboardinit cpu/amd/car/cache_as_ram.inc
+end
+
+###
+### This is the early phase of linuxBIOS startup
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+if USE_FALLBACK_IMAGE
+ if USE_DCACHE_RAM
+ ldscript /arch/i386/lib/failover.lds
+ end
+end
+
+###
+### O.k. We aren't just an intermediary anymore!
+###
+
+##
+## Setup RAM
+##
+if USE_DCACHE_RAM
+
+ if CONFIG_USE_INIT
+ initobject cache_as_ram_auto.o
+ else
+ mainboardinit ./cache_as_ram_auto.inc
+ end
+
+end
+
+##
+## Include the secondary Configuration files
+##
+if CONFIG_CHIP_NAME
+ config chip.h
+end
+
+# sample config for amd/serengeti_cheetah
+chip northbridge/amd/amdk8/root_complex
+ device apic_cluster 0 on
+ chip cpu/amd/socket_F
+ device apic 0 on end
+ end
+ end
+ device pci_domain 0 on
+ chip northbridge/amd/amdk8
+ device pci 18.0 on end
+ device pci 18.0 on end
+ device pci 18.0 on # northbridge
+ # devices on link 0
+ chip southbridge/broadcom/bcm5780 # HT2000
+ device pci 0.0 on end # PXB 1 0x0130
+ device pci 1.0 on # PXB 2 0x0130
+ device pci 4.0 on end # GB E 0x1668 vid = 0x14e4
+ device pci 4.1 on end # GB E 0x1669 vid = 0x14e4
+ end
+ device pci 2.0 on end # PCI E 1 #0x0132
+ device pci 3.0 on end # PCI E 2
+ device pci 4.0 on end # PCI E 3
+ device pci 5.0 on end # PCI E 4
+ end
+ chip southbridge/broadcom/bcm5785 # HT1000
+ device pci 0.0 on # HT PXB 0x0036
+ device pci d.0 on end # PPBX 0x0104
+ device pci e.0 on end # SATA 0x024a
+ device pci e.1 on end # SATA 0x024a bx_a001
+ device pci e.2 on end # SATA 0x024a bx_a001
+ device pci e.3 on end # SATA 0x024a bx_a001
+ end
+ device pci 1.0 on # Legacy pci main 0x0205
+ end
+ device pci 1.1 on end # IDE 0x0214
+ device pci 1.2 on # LPC 0x0234
+ chip superio/nsc/pc87417
+ device pnp 2e.0 off # Floppy
+ io 0x60 = 0x3f0
+ irq 0x70 = 6
+ drq 0x74 = 2
+ end
+ device pnp 2e.1 off # Parallel Port
+ io 0x60 = 0x378
+ irq 0x70 = 7
+ end
+ device pnp 2e.2 off # Com 2
+ io 0x60 = 0x2f8
+ irq 0x70 = 3
+ end
+ device pnp 2e.3 on # Com 1
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ end
+ device pnp 2e.4 off end # SWC
+ device pnp 2e.5 off end # Mouse
+ device pnp 2e.6 on # Keyboard
+ io 0x60 = 0x60
+ io 0x62 = 0x64
+ irq 0x70 = 1
+ end
+ device pnp 2e.7 off end # GPIO
+ device pnp 2e.f off end # XBUS
+ device pnp 2e.10 on #RTC
+ io 0x60 = 0x70
+ io 0x62 = 0x72
+ end
+ end
+ end
+ device pci 1.3 on end # WDTimer 0x0238
+ device pci 1.4 on end # XIOAPIC0 0x0235
+ device pci 1.5 on end # XIOAPIC1
+ device pci 1.6 on end # XIOAPIC2
+ device pci 2.0 on end # USB 0x0223
+ device pci 2.1 on end # USB
+ device pci 2.2 on end # USB
+ #when HT_CHAIN_END_UNITID_BASE (0,1) < HT_CHAIN_UNITID_BASE (6,,,,),
+ chip drivers/pci/onboard
+ device pci 3.0 on end # it is in bcm5785_0 bus, but the device id can not be changed even unitid is changed, fake one to get the rom_address
+ # if HT_CHAIN_END_UNITID_BASE=0, it is 4, if HT_CHAIN_END_UNITID_BASE=1, it is 3
+ register "rom_address" = "0xfff80000"
+ end
+ #bx_a013+ start
+ #chip drivers/pci/onboard #SATA2
+ # device pci 5.0 on end
+ # device pci 5.1 on end
+ # device pci 5.2 on end
+ # device pci 5.3 on end
+ #end
+ #bx_a013+ end
+
+ end
+ #when HT_CHAIN_END_UNITID_BASE > HT_CHAIN_UNITID_BASE (6, ,,,,)
+# chip drivers/pci/onboard
+# device pci 0.0 on end # fake, will be disabled
+# end
+# chip drivers/pci/onboard
+# device pci 4.0 on end # it is in bcm5785_0 bus, but the device id can not be changed even unitid is changed
+# register "rom_address" = "0xfff80000"
+# end
+
+ end # device pci 18.0
+ device pci 18.1 on end
+ device pci 18.2 on end
+ device pci 18.3 on end
+ end # amdk8
+ end #pci_domain
+# chip drivers/generic/debug
+# device pnp 0.0 off end # chip name
+# device pnp 0.1 on end # pci_regs_all
+# device pnp 0.2 off end # mem
+# device pnp 0.3 off end # cpuid
+# device pnp 0.4 off end # smbus_regs_all
+# device pnp 0.5 off end # dual core msr
+# device pnp 0.6 off end # cache size
+# device pnp 0.7 off end # tsc
+# end
+
+end
+
+
diff --git a/src/mainboard/msi/ms9185/Options.lb b/src/mainboard/msi/ms9185/Options.lb
new file mode 100644
index 0000000000..da8eee4f3a
--- /dev/null
+++ b/src/mainboard/msi/ms9185/Options.lb
@@ -0,0 +1,332 @@
+##
+## This file is part of the LinuxBIOS project.
+##
+## Copyright (C) 2006 AMD
+## Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
+##
+## Copyright (C) 2006 MSI
+## Written by bxshi <bingxunshi@gmail.com> for MSI.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses HAVE_ACPI_TABLES
+uses ACPI_SSDTX_NUM
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses IRQ_SLOT_COUNT
+uses HAVE_OPTION_TABLE
+uses CONFIG_MAX_CPUS
+uses CONFIG_MAX_PHYSICAL_CPUS
+uses CONFIG_LOGICAL_CPUS
+uses CONFIG_IOAPIC
+uses CONFIG_SMP
+uses FALLBACK_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM
+uses CONFIG_ROM_STREAM_START
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses USE_OPTION_TABLE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD_PART_NUMBER
+uses MAINBOARD_VENDOR
+uses MAINBOARD
+uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses LINUXBIOS_EXTRA_VERSION
+uses _RAMBASE
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_CONSOLE_SERIAL8250
+uses HAVE_INIT_TIMER
+uses CONFIG_GDB_STUB
+uses CONFIG_GDB_STUB
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses OBJCOPY
+uses CONFIG_CHIP_NAME
+uses CONFIG_CONSOLE_VGA
+uses CONFIG_PCI_ROM_RUN
+uses HW_MEM_HOLE_SIZEK
+uses HW_MEM_HOLE_SIZE_AUTO_INC
+uses K8_HT_FREQ_1G_SUPPORT
+
+uses HT_CHAIN_UNITID_BASE
+uses HT_CHAIN_END_UNITID_BASE
+uses SB_HT_CHAIN_ON_BUS0
+uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses USE_DCACHE_RAM
+uses DCACHE_RAM_BASE
+uses DCACHE_RAM_SIZE
+uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_USE_INIT
+
+uses SERIAL_CPU_INIT
+
+uses ENABLE_APIC_EXT_ID
+uses APIC_ID_OFFSET
+uses LIFT_BSP_APIC_ID
+
+uses CONFIG_PCI_64BIT_PREF_MEM
+
+uses CONFIG_LB_MEM_TOPK
+
+
+###
+### Build options
+###
+
+##
+## ROM_SIZE is the size of boot ROM that this board will use.
+##
+default ROM_SIZE=524288
+
+##
+## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+##
+#default FALLBACK_SIZE=131072
+#256K
+default FALLBACK_SIZE=0x40000
+
+#more 1M for pgtbl
+default CONFIG_LB_MEM_TOPK=2048
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=1
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=11
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+default HAVE_MP_TABLE=1
+
+## ACPI tables will be included
+#default HAVE_ACPI_TABLES=1
+## extra SSDT num
+#default ACPI_SSDTX_NUM=1
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=1
+
+##
+## Move the default LinuxBIOS cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+##
+default CONFIG_SMP=1
+default CONFIG_MAX_CPUS=4
+default CONFIG_MAX_PHYSICAL_CPUS=2
+default CONFIG_LOGICAL_CPUS=1
+
+default SERIAL_CPU_INIT=0
+
+default ENABLE_APIC_EXT_ID=0
+default APIC_ID_OFFSET=0x8
+default LIFT_BSP_APIC_ID=1
+
+#CHIP_NAME ?
+default CONFIG_CHIP_NAME=1
+
+#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
+#2G
+#default HW_MEM_HOLE_SIZEK=0x200000
+#1G
+default HW_MEM_HOLE_SIZEK=0x100000
+#512M
+#default HW_MEM_HOLE_SIZEK=0x80000
+
+#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
+#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+
+#Opteron K8 1G HT Support
+default K8_HT_FREQ_1G_SUPPORT=1
+
+#VGA Console
+default CONFIG_CONSOLE_VGA=1
+default CONFIG_PCI_ROM_RUN=1
+
+#HT Unit ID offset, default is 1, the typical one
+default HT_CHAIN_UNITID_BASE=0x06
+
+#real SB Unit ID, default is 0x20, mean dont touch it at last
+default HT_CHAIN_END_UNITID_BASE=0x01
+
+#make the SB HT chain on bus 0, default is not (0)
+default SB_HT_CHAIN_ON_BUS0=2
+
+#only offset for SB chain?, default is yes(1)
+#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+
+#allow capable device use that above 4G
+#default CONFIG_PCI_64BIT_PREF_MEM=1
+
+##
+## enable CACHE_AS_RAM specifics
+##
+default USE_DCACHE_RAM=1
+default DCACHE_RAM_BASE=0xcc000
+default DCACHE_RAM_SIZE=0x04000
+default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_INIT=0
+
+##
+## Build code to setup a generic IOAPIC
+##
+default CONFIG_IOAPIC=1
+
+##
+## Clean up the motherboard id strings
+##
+default MAINBOARD_PART_NUMBER="MS9185"
+default MAINBOARD_VENDOR="MSI"
+default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022
+default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 65536
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 32K heap
+##
+default HEAP_SIZE=0x8000
+
+##
+## Only use the option table in a normal image
+##
+default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+
+##
+## LinuxBIOS C code runs at this location in RAM
+##
+default _RAMBASE=0x00100000
+
+##
+## Load the payload from the ROM
+##
+default CONFIG_ROM_STREAM = 1
+
+###
+### Defaults of options that you may want to override in the target config file
+###
+
+##
+## The default compiler
+##
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## Disable the gdb stub by default
+##
+default CONFIG_GDB_STUB=0
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG 1 system is unusable
+## ALERT 2 action must be taken immediately
+## CRIT 3 critical conditions
+## ERR 4 error conditions
+## WARNING 5 warning conditions
+## NOTICE 6 normal but significant condition
+## INFO 7 informational
+## DEBUG 8 debug-level messages
+## SPEW 9 Way too many details
+
+## Request this level of debugging output
+default DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+default MAXIMUM_CONSOLE_LOGLEVEL=8
+
+##
+## Select power on after power fail setting
+default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+
+### End Options.lb
+end
diff --git a/src/mainboard/msi/ms9185/cache_as_ram_auto.c b/src/mainboard/msi/ms9185/cache_as_ram_auto.c
new file mode 100644
index 0000000000..bb2212fb2e
--- /dev/null
+++ b/src/mainboard/msi/ms9185/cache_as_ram_auto.c
@@ -0,0 +1,375 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2006 Tyan
+ * Copyright (C) 2006 AMD
+ * Written by Yinghai Lu <yinghailu@gmail.com> for Tyan and AMD.
+ *
+ * Copyright (C) 2006 MSI
+ * Written by bxshi <bingxunshi@gmail.com> for MSI.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define ASSEMBLY 1
+#define __ROMCC__
+
+#define RAMINIT_SYSINFO 1
+#define CACHE_AS_RAM_ADDRESS_DEBUG 0
+
+#define SET_NB_CFG_54 1
+
+//used by raminit
+#define QRANK_DIMM_SUPPORT 1
+
+//used by incoherent_ht
+//#define K8_SCAN_PCI_BUS 1
+//#define K8_ALLOCATE_IO_RANGE 1
+
+
+//used by init_cpus and fidvid
+#define K8_SET_FIDVID 1
+//if we want to wait for core1 done before DQS training, set it to 0
+#define K8_SET_FIDVID_CORE0_ONLY 1
+
+#define DEBUG_SMBUS 1
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <cpu/x86/lapic.h>
+#include "option_table.h"
+#include "pc80/mc146818rtc_early.c"
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+
+#if 0
+static void post_code(uint8_t value) {
+#if 1
+ int i;
+ for(i=0;i<0x80000;i++) {
+ outb(value, 0x80);
+ }
+#endif
+}
+#endif
+
+#include <cpu/amd/model_fxx_rev.h>
+#include "southbridge/broadcom/bcm5785/bcm5785_early_smbus.c"
+#include "northbridge/amd/amdk8/raminit.h"
+#include "cpu/amd/model_fxx/apic_timer.c"
+#include "lib/delay.c"
+
+#if CONFIG_USE_INIT == 0
+ #include "lib/memcpy.c"
+#endif
+
+
+#include "cpu/x86/lapic/boot_cpu.c"
+#include "northbridge/amd/amdk8/reset_test.c"
+#include "northbridge/amd/amdk8/debug.c"
+#include "superio/nsc/pc87417/pc87417_early_serial.c"
+#include "cpu/amd/mtrr/amd_earlymtrr.c"
+#include "cpu/x86/bist.h"
+
+#include "northbridge/amd/amdk8/setup_resource_map.c"
+
+#define SERIAL_DEV PNP_DEV(0x2e, PC87417_SP1)
+#define RTC_DEV PNP_DEV(0x2e, PC87417_RTC)
+#include "southbridge/broadcom/bcm5785/bcm5785_early_setup.c"
+static void memreset_setup(void)
+{
+}
+
+static void memreset(int controllers, const struct mem_controller *ctrl)
+{
+}
+
+static inline void activate_spd_rom(const struct mem_controller *ctrl)
+{
+#define SMBUS_SWITCH1 0x70
+#define SMBUS_SWITCH2 0x72
+ unsigned device = (ctrl->channel0[0]) >> 8;
+ smbus_send_byte(SMBUS_SWITCH1, device & 0x0f);
+ smbus_send_byte(SMBUS_SWITCH2, (device >> 4) & 0x0f );
+}
+
+#if 0
+static inline void change_i2c_mux(unsigned device)
+{
+#define SMBUS_SWITCH1 0x70
+#define SMBUS_SWITCH2 0x72
+ smbus_send_byte(SMBUS_SWITCH1, device & 0x0f);
+ smbus_send_byte(SMBUS_SWITCH2, (device >> 4) & 0x0f );
+}
+#endif
+
+
+
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+ return smbus_read_byte(device, address);
+}
+
+#include "northbridge/amd/amdk8/amdk8_f.h"
+#include "northbridge/amd/amdk8/coherent_ht.c"
+
+#include "northbridge/amd/amdk8/incoherent_ht.c"
+
+#include "northbridge/amd/amdk8/raminit_f.c"
+
+#include "sdram/generic_sdram.c"
+
+ /* msi does not want the default */
+#include "resourcemap.c"
+
+#include "cpu/amd/dualcore/dualcore.c"
+
+#define RC0 (0x10<<8)
+#define RC1 (0x01<<8)
+
+#define DIMM0 0x50
+#define DIMM1 0x51
+#define DIMM2 0x52
+#define DIMM3 0x53
+#define DIMM4 0x54
+#define DIMM5 0x55
+#define DIMM6 0x56
+#define DIMM7 0x57
+
+
+#include "cpu/amd/car/copy_and_run.c"
+#include "cpu/amd/car/post_cache_as_ram.c"
+
+#include "cpu/amd/model_fxx/init_cpus.c"
+
+#include "cpu/amd/model_fxx/fidvid.c"
+
+#if USE_FALLBACK_IMAGE == 1
+
+#include "northbridge/amd/amdk8/early_ht.c"
+
+void failover_process(unsigned long bist, unsigned long cpu_init_detectedx)
+{
+
+ /* Is this a cpu only reset? Is this a secondary cpu? */
+ if ((cpu_init_detectedx) || (!boot_cpu())) {
+ if (last_boot_normal()) { // RTC already inited
+ goto normal_image;
+ } else {
+ goto fallback_image;
+ }
+ }
+ /* Nothing special needs to be done to find bus 0 */
+ /* Allow the HT devices to be found */
+
+ enumerate_ht_chain();
+
+ bcm5785_enable_rom();
+
+ bcm5785_enable_lpc();
+
+ //enable RTC
+ pc87417_enable_dev(RTC_DEV);
+
+ /* Is this a deliberate reset by the bios */
+// post_code(0x22);
+ if (bios_reset_detected() && last_boot_normal()) {
+ goto normal_image;
+ }
+ /* This is the primary cpu how should I boot? */
+ else if (do_normal_boot()) {
+ goto normal_image;
+ }
+ else {
+ goto fallback_image;
+ }
+ normal_image:
+// post_code(0x23);
+ __asm__ volatile ("jmp __normal_image"
+ : /* outputs */
+ : "a" (bist), "b" (cpu_init_detectedx) /* inputs */
+ );
+
+ fallback_image:
+// post_code(0x25);
+ ;
+
+}
+#endif
+
+void real_main(unsigned long bist, unsigned long cpu_init_detectedx);
+
+void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
+{
+
+#if USE_FALLBACK_IMAGE == 1
+ failover_process(bist, cpu_init_detectedx);
+#endif
+ real_main(bist, cpu_init_detectedx);
+
+}
+
+void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
+{
+ static const uint16_t spd_addr[] = {
+ //first node
+ RC0|DIMM0, RC0|DIMM2, RC0|DIMM4, RC0|DIMM6,
+ RC0|DIMM1, RC0|DIMM3, RC0|DIMM5, RC0|DIMM7,
+#if CONFIG_MAX_PHYSICAL_CPUS > 1
+ //second node
+ RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6,
+ RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7,
+#endif
+
+ };
+
+ struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+
+ int needs_reset;
+ unsigned bsp_apicid = 0;
+
+ if (bist == 0) {
+ bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
+ }
+
+// post_code(0x32);
+
+ pc87417_enable_serial(SERIAL_DEV, TTYS0_BASE);
+ uart_init();
+ console_init();
+
+// dump_mem(DCACHE_RAM_BASE+DCACHE_RAM_SIZE-0x200, DCACHE_RAM_BASE+DCACHE_RAM_SIZE);
+
+ /* Halt if there was a built in self test failure */
+ report_bist_failure(bist);
+
+ print_debug("*sysinfo range: ["); print_debug_hex32(sysinfo); print_debug(","); print_debug_hex32((unsigned long)sysinfo+sizeof(struct sys_info)); print_debug(")\r\n");
+
+ setup_ms9185_resource_map();
+#if 0
+ dump_pci_device(PCI_DEV(0, 0x18, 0));
+ dump_pci_device(PCI_DEV(0, 0x19, 0));
+#endif
+
+ print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n");
+
+ setup_coherent_ht_domain();
+
+ wait_all_core0_started();
+#if CONFIG_LOGICAL_CPUS==1
+ // It is said that we should start core1 after all core0 launched
+ /* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
+ * So here need to make sure last core0 is started, esp for two way system,
+ * (there may be apic id conflicts in that case)
+ */
+ start_other_cores();
+//bx_a010- wait_all_other_cores_started(bsp_apicid);
+#endif
+
+ /* it will set up chains and store link pair for optimization later */
+ ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
+
+ bcm5785_early_setup();
+
+
+#if 0
+ //it your CPU min fid is 1G, you can change HT to 1G and FID to max one time.
+ needs_reset = optimize_link_coherent_ht();
+ needs_reset |= optimize_link_incoherent_ht(sysinfo);
+#endif
+
+#if K8_SET_FIDVID == 1
+
+ {
+ msr_t msr;
+ msr=rdmsr(0xc0010042);
+ print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\r\n");
+
+ }
+
+ enable_fid_change();
+
+ enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
+
+ init_fidvid_bsp(bsp_apicid);
+
+ // show final fid and vid
+ {
+ msr_t msr;
+ msr=rdmsr(0xc0010042);
+ print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\r\n");
+
+ }
+#endif
+
+#if 1
+ needs_reset = optimize_link_coherent_ht();
+ needs_reset |= optimize_link_incoherent_ht(sysinfo);
+
+ // fidvid change will issue one LDTSTOP and the HT change will be effective too
+ if (needs_reset) {
+ print_info("ht reset -\r\n");
+ soft_reset();
+ }
+#endif
+ allow_all_aps_stop(bsp_apicid);
+
+ //It's the time to set ctrl in sysinfo now;
+ fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
+
+ enable_smbus();
+
+#if 0
+ int i;
+ for(i=0;i<2;i++) {
+ activate_spd_rom(sysinfo->ctrl+i);
+ dump_smbus_registers();
+ }
+#endif
+
+#if 0
+ int i;
+ for(i=1;i<256;i<<=1) {
+ change_i2c_mux(i);
+ dump_smbus_registers();
+ }
+#endif
+
+ memreset_setup();
+
+ //do we need apci timer, tsc...., only debug need it for better output
+ /* all ap stopped? */
+// init_timer(); // Need to use TMICT to synconize FID/VID
+
+ sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
+
+#if 0
+ print_pci_devices();
+#endif
+
+#if 0
+// dump_pci_devices();
+ dump_pci_device_index_wait(PCI_DEV(0, 0x18, 2), 0x98);
+ dump_pci_device_index_wait(PCI_DEV(0, 0x19, 2), 0x98);
+#endif
+
+ post_cache_as_ram();
+
+
+}
diff --git a/src/mainboard/msi/ms9185/chip.h b/src/mainboard/msi/ms9185/chip.h
new file mode 100644
index 0000000000..6bd0a48912
--- /dev/null
+++ b/src/mainboard/msi/ms9185/chip.h
@@ -0,0 +1,28 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2006 MSI
+ * Written by bxshi <bingxunshi@gmail.com> for MSI.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+extern struct chip_operations mainboard_msi_ms9185_ops;
+
+struct mainboard_msi_ms9185_config {
+// int fixup_scsi;
+// int fixup_vga;
+};
+
diff --git a/src/mainboard/msi/ms9185/cmos.layout b/src/mainboard/msi/ms9185/cmos.layout
new file mode 100644
index 0000000000..3f6d68f41c
--- /dev/null
+++ b/src/mainboard/msi/ms9185/cmos.layout
@@ -0,0 +1,98 @@
+entries
+
+#start-bit length config config-ID name
+#0 8 r 0 seconds
+#8 8 r 0 alarm_seconds
+#16 8 r 0 minutes
+#24 8 r 0 alarm_minutes
+#32 8 r 0 hours
+#40 8 r 0 alarm_hours
+#48 8 r 0 day_of_week
+#56 8 r 0 day_of_month
+#64 8 r 0 month
+#72 8 r 0 year
+#80 4 r 0 rate_select
+#84 3 r 0 REF_Clock
+#87 1 r 0 UIP
+#88 1 r 0 auto_switch_DST
+#89 1 r 0 24_hour_mode
+#90 1 r 0 binary_values_enable
+#91 1 r 0 square-wave_out_enable
+#92 1 r 0 update_finished_enable
+#93 1 r 0 alarm_interrupt_enable
+#94 1 r 0 periodic_interrupt_enable
+#95 1 r 0 disable_clock_updates
+#96 288 r 0 temporary_filler
+0 384 r 0 reserved_memory
+384 1 e 4 boot_option
+385 1 e 4 last_boot
+386 1 e 1 ECC_memory
+388 4 r 0 reboot_bits
+392 3 e 5 baud_rate
+395 1 e 1 hw_scrubber
+396 1 e 1 interleave_chip_selects
+397 2 e 8 max_mem_clock
+399 1 e 2 dual_core
+400 1 e 1 power_on_after_fail
+412 4 e 6 debug_level
+416 4 e 7 boot_first
+420 4 e 7 boot_second
+424 4 e 7 boot_third
+428 4 h 0 boot_index
+432 8 h 0 boot_countdown
+440 4 e 9 slow_cpu
+444 1 e 1 nmi
+445 1 e 1 iommu
+728 256 h 0 user_data
+984 16 h 0 check_sum
+# Reserve the extended AMD configuration registers
+1000 24 r 0 reserved_memory
+
+
+
+enumerations
+
+#ID value text
+1 0 Disable
+1 1 Enable
+2 0 Enable
+2 1 Disable
+4 0 Fallback
+4 1 Normal
+5 0 115200
+5 1 57600
+5 2 38400
+5 3 19200
+5 4 9600
+5 5 4800
+5 6 2400
+5 7 1200
+6 6 Notice
+6 7 Info
+6 8 Debug
+6 9 Spew
+7 0 Network
+7 1 HDD
+7 2 Floppy
+7 8 Fallback_Network
+7 9 Fallback_HDD
+7 10 Fallback_Floppy
+#7 3 ROM
+8 0 400Mhz
+8 1 333Mhz
+8 2 266Mhz
+8 3 200Mhz
+9 0 off
+9 1 87.5%
+9 2 75.0%
+9 3 62.5%
+9 4 50.0%
+9 5 37.5%
+9 6 25.0%
+9 7 12.5%
+
+checksums
+
+checksum 392 983 984
+
+
diff --git a/src/mainboard/msi/ms9185/get_bus_conf.c b/src/mainboard/msi/ms9185/get_bus_conf.c
new file mode 100644
index 0000000000..1620bf870f
--- /dev/null
+++ b/src/mainboard/msi/ms9185/get_bus_conf.c
@@ -0,0 +1,144 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2006 AMD
+ * Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
+ *
+ * Copyright (C) 2006 MSI
+ * Written by bxshi <bingxunshi@gmail.com> for MSI.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include <console/console.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <string.h>
+#include <stdint.h>
+#if CONFIG_LOGICAL_CPUS==1
+#include <cpu/amd/dualcore.h>
+#endif
+
+#include <cpu/amd/amdk8_sysconf.h>
+
+#include "mb_sysconf.h"
+
+// Global variables for MB layouts and these will be shared by irqtable mptable and acpi_tables
+struct mb_sysconf_t mb_sysconf;
+
+static unsigned pci1234x[] =
+{ //Here you only need to set value in pci1234 for HT-IO that could be installed or not
+ //You may need to preset pci1234 for HTIO board, please refer to src/northbridge/amd/amdk8/get_sblk_pci1234.c for detail
+ 0x0000ff0,
+ 0x0000ff0,
+// 0x0000ff0,
+// 0x0000ff0,
+// 0x0000ff0,
+// 0x0000ff0,
+// 0x0000ff0,
+// 0x0000ff0
+};
+static unsigned hcdnx[] =
+{ //HT Chain device num, actually it is unit id base of every ht device in chain, assume every chain only have 4 ht device at most
+ 0x20202020,
+ 0x20202020,
+// 0x20202020,
+// 0x20202020,
+// 0x20202020,
+// 0x20202020,
+// 0x20202020,
+// 0x20202020,
+};
+
+extern void get_sblk_pci1234(void);
+
+static unsigned get_bus_conf_done = 0;
+
+void get_bus_conf(void)
+{
+
+ unsigned apicid_base;
+
+ device_t dev;
+ int i;
+ struct mb_sysconf_t *m;
+
+ if(get_bus_conf_done==1) return; //do it only once
+
+ get_bus_conf_done = 1;
+
+ sysconf.mb = &mb_sysconf;
+
+ m = sysconf.mb;
+
+ sysconf.hc_possible_num = sizeof(pci1234x)/sizeof(pci1234x[0]);
+
+ for(i=0;i<sysconf.hc_possible_num; i++) {
+ sysconf.pci1234[i] = pci1234x[i];
+ sysconf.hcdn[i] = hcdnx[i];
+ }
+
+ get_sblk_pci1234();
+
+ sysconf.sbdn = (sysconf.hcdn[0] >> 8) & 0xff;
+ m->sbdn2 = sysconf.hcdn[0] & 0xff; // bcm5780
+
+ m->bus_bcm5785_0 = (sysconf.pci1234[0] >> 16) & 0xff;
+ m->bus_bcm5780[0] = m->bus_bcm5785_0;
+
+ /* bcm5785 */
+ dev = dev_find_slot(m->bus_bcm5785_0, PCI_DEVFN(sysconf.sbdn,0));
+ if (dev) {
+ m->bus_bcm5785_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
+ dev = dev_find_slot(m->bus_bcm5785_1, PCI_DEVFN(0xd,0));
+ if(dev) {
+ m->bus_bcm5785_1_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
+#if HT_CHAIN_END_UNITID_BASE >= HT_CHAIN_UNITID_BASE
+ m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
+ m->bus_isa++;
+ printk_debug("bus_isa=%d\n",m->bus_isa);
+#endif
+ }
+ }
+ else {
+ printk_debug("ERROR - could not find PCI %02x:%02x.0, using defaults\n", m->bus_bcm5785_0, sysconf.sbdn);
+ }
+
+ /* bcm5780 */
+ for(i = 1; i < 7; i++) {
+ dev = dev_find_slot(m->bus_bcm5780[0], PCI_DEVFN(m->sbdn2 + i - 1,0));
+ if(dev) {
+ m->bus_bcm5780[i] = pci_read_config8(dev, PCI_SECONDARY_BUS);
+#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE
+ m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
+ m->bus_isa++;
+ printk_debug("bus_isa=%d\n",m->bus_isa);
+#endif
+
+ }
+ else {
+ printk_debug("ERROR - could not find PCI %02x:%02x.0, using defaults\n", m->bus_bcm5780[0], m->sbdn2+i-1);
+ }
+ }
+
+
+/*I/O APICs: APIC ID Version State Address*/
+#if CONFIG_LOGICAL_CPUS==1
+ apicid_base = get_apicid_base(3);
+#else
+ apicid_base = CONFIG_MAX_PHYSICAL_CPUS;
+#endif
+ for(i=0;i<3;i++)
+ m->apicid_bcm5785[i] = apicid_base+i;
+}
diff --git a/src/mainboard/msi/ms9185/irq_tables.c b/src/mainboard/msi/ms9185/irq_tables.c
new file mode 100644
index 0000000000..4769b03bac
--- /dev/null
+++ b/src/mainboard/msi/ms9185/irq_tables.c
@@ -0,0 +1,126 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2006 AMD
+ * Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
+ *
+ * Copyright (C) 2006 MSI
+ * Written by bxshi <bingxunshi@gmail.com> for MSI.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+/* This file was generated by getpir.c, do not modify!
+ (but if you do, please run checkpir on it to verify)
+ Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up
+
+ Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+#include <console/console.h>
+#include <device/pci.h>
+#include <string.h>
+#include <stdint.h>
+#include <arch/pirq_routing.h>
+#include <cpu/amd/amdk8_sysconf.h>
+
+#include "mb_sysconf.h"
+
+
+static void write_pirq_info(struct irq_info *pirq_info, uint8_t bus, uint8_t devfn, uint8_t link0, uint16_t bitmap0,
+ uint8_t link1, uint16_t bitmap1, uint8_t link2, uint16_t bitmap2,uint8_t link3, uint16_t bitmap3,
+ uint8_t slot, uint8_t rfu)
+{
+ pirq_info->bus = bus;
+ pirq_info->devfn = devfn;
+
+ pirq_info->irq[0].link = link0;
+ pirq_info->irq[0].bitmap = bitmap0;
+ pirq_info->irq[1].link = link1;
+ pirq_info->irq[1].bitmap = bitmap1;
+ pirq_info->irq[2].link = link2;
+ pirq_info->irq[2].bitmap = bitmap2;
+ pirq_info->irq[3].link = link3;
+ pirq_info->irq[3].bitmap = bitmap3;
+
+ pirq_info->slot = slot;
+ pirq_info->rfu = rfu;
+}
+
+extern void get_bus_conf(void);
+
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+
+ struct irq_routing_table *pirq;
+ struct irq_info *pirq_info;
+ unsigned slot_num;
+ uint8_t *v;
+
+ uint8_t sum=0;
+ int i;
+
+ struct mb_sysconf_t *m;
+
+ get_bus_conf();
+
+ m = sysconf.mb;
+
+ /* Align the table to be 16 byte aligned. */
+ addr += 15;
+ addr &= ~15;
+
+ /* This table must be betweeen 0xf0000 & 0x100000 */
+ printk_info("Writing IRQ routing tables to 0x%x...", addr);
+
+ pirq = (void *)(addr);
+ v = (uint8_t *)(addr);
+
+ pirq->signature = PIRQ_SIGNATURE;
+ pirq->version = PIRQ_VERSION;
+
+ pirq->rtr_bus = m->bus_bcm5785_0;
+ pirq->rtr_devfn = (sysconf.sbdn<<3)|0;
+
+ pirq->exclusive_irqs = 0;
+
+ pirq->rtr_vendor = 0x1166;
+ pirq->rtr_device = 0x0036;
+
+ pirq->miniport_data = 0;
+
+ memset(pirq->rfu, 0, sizeof(pirq->rfu));
+
+ pirq_info = (void *) ( &pirq->checksum + 1);
+ slot_num = 0;
+//pci bridge
+ write_pirq_info(pirq_info, m->bus_bcm5785_0, (sysconf.sbdn<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
+ pirq_info++; slot_num++;
+
+ pirq->size = 32 + 16 * slot_num;
+
+ for (i = 0; i < pirq->size; i++)
+ sum += v[i];
+
+ sum = pirq->checksum - sum;
+
+ if (sum != pirq->checksum) {
+ pirq->checksum = sum;
+ }
+
+ printk_info("done.\n");
+
+ return (unsigned long) pirq_info;
+
+}
diff --git a/src/mainboard/msi/ms9185/mainboard.c b/src/mainboard/msi/ms9185/mainboard.c
new file mode 100644
index 0000000000..366f88e379
--- /dev/null
+++ b/src/mainboard/msi/ms9185/mainboard.c
@@ -0,0 +1,33 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2006 MSI
+ * Written by bxshi <bingxunshi@gmail.com> for MSI.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "chip.h"
+
+#if CONFIG_CHIP_NAME == 1
+struct chip_operations mainboard_msi_ms9185_ops = {
+ CHIP_NAME("MSI MS-9185 mainboard")
+};
+#endif
diff --git a/src/mainboard/msi/ms9185/mb_sysconf.h b/src/mainboard/msi/ms9185/mb_sysconf.h
new file mode 100644
index 0000000000..e52be15982
--- /dev/null
+++ b/src/mainboard/msi/ms9185/mb_sysconf.h
@@ -0,0 +1,40 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2006 AMD
+ * Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
+ *
+ * Copyright (C) 2006 MSI
+ * Written by bxshi <bingxunshi@gmail.com> for MSI.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef MB_SYSCONF_H
+#define MB_SYSCONF_H
+
+struct mb_sysconf_t {
+ unsigned char bus_isa;
+ unsigned char bus_bcm5780[7];
+ unsigned char bus_bcm5785_0;
+ unsigned char bus_bcm5785_1;
+ unsigned char bus_bcm5785_1_1;
+ unsigned apicid_bcm5785[3];
+
+ unsigned sbdn2;
+};
+
+#endif
+
diff --git a/src/mainboard/msi/ms9185/mptable.c b/src/mainboard/msi/ms9185/mptable.c
new file mode 100644
index 0000000000..4045745bcc
--- /dev/null
+++ b/src/mainboard/msi/ms9185/mptable.c
@@ -0,0 +1,205 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2001 Eric W.Biederman<ebiderman@lnxi.com>
+ *
+ * Copyright (C) 2006 AMD
+ * Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
+ *
+ * Copyright (C) 2006 MSI
+ * Written by bxshi <bingxunshi@gmail.com> for MSI.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <arch/smp/mpspec.h>
+#include <arch/io.h>
+#include <device/pci.h>
+#include <string.h>
+#include <stdint.h>
+#if CONFIG_LOGICAL_CPUS==1
+#include <cpu/amd/dualcore.h>
+#endif
+
+#include <cpu/amd/amdk8_sysconf.h>
+
+#include "mb_sysconf.h"
+
+extern void get_bus_conf(void);
+
+void *smp_write_config_table(void *v)
+{
+ static const char sig[4] = "PCMP";
+ static const char oem[3] = "MSI";
+ static const char productid[6] = "MS9185 ";
+ struct mp_config_table *mc;
+
+ unsigned char bus_num;
+ int i;
+ struct mb_sysconf_t *m;
+
+ mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN);
+ memset(mc, 0, sizeof(*mc));
+
+ memcpy(mc->mpc_signature, sig, sizeof(sig));
+ mc->mpc_length = sizeof(*mc); /* initially just the header */
+ mc->mpc_spec = 0x04;
+ mc->mpc_checksum = 0; /* not yet computed */
+ memcpy(mc->mpc_oem, oem, sizeof(oem));
+ memcpy(mc->mpc_productid, productid, sizeof(productid));
+ mc->mpc_oemptr = 0;
+ mc->mpc_oemsize = 0;
+ mc->mpc_entry_count = 0; /* No entries yet... */
+ mc->mpc_lapic = LAPIC_ADDR;
+ mc->mpe_length = 0;
+ mc->mpe_checksum = 0;
+ mc->reserved = 0;
+
+ smp_write_processors(mc);
+
+ get_bus_conf();
+ m = sysconf.mb;
+
+/*Bus: Bus ID Type*/
+ /* define bus and isa numbers */
+ for(bus_num = 0; bus_num < m->bus_isa; bus_num++) {
+ smp_write_bus(mc, bus_num, "PCI ");
+ }
+ smp_write_bus(mc, m->bus_isa, "ISA ");
+
+/*I/O APICs: APIC ID Version State Address*/
+ {
+ device_t dev = 0;
+ int i;
+ struct resource *res;
+ for(i=0; i<3; i++) {
+ dev = dev_find_device(0x1166, 0x0235, dev);
+ if (dev) {
+ res = find_resource(dev, PCI_BASE_ADDRESS_0);
+ if (res) {
+ smp_write_ioapic(mc, m->apicid_bcm5785[i], 0x11, res->base);
+ }
+ }
+ }
+
+ }
+
+/*I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# */
+ smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, m->apicid_bcm5785[0], 0x0);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x1, m->apicid_bcm5785[0], 0x1);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, m->apicid_bcm5785[0], 0x2);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x3, m->apicid_bcm5785[0], 0x3);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x4, m->apicid_bcm5785[0], 0x4);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x5, m->apicid_bcm5785[0], 0x5);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x6, m->apicid_bcm5785[0], 0x6);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x7, m->apicid_bcm5785[0], 0x7);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x8, m->apicid_bcm5785[0], 0x8);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x9, m->apicid_bcm5785[0], 0x9);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0xc, m->apicid_bcm5785[0], 0xc);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0xd, m->apicid_bcm5785[0], 0xd);
+
+//IDE
+ outb(0x02, 0xc00); outb(0x0e, 0xc01);
+
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_bcm5785_0, ((1+sysconf.sbdn)<<2)|1, m->apicid_bcm5785[0], 0xe); // IDE
+
+//SATA
+ outb(0x07, 0xc00); outb(0x0f, 0xc01);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_1, (0x0e<<2)|0, m->apicid_bcm5785[0], 0xf);
+
+//USB
+ outb(0x01, 0xc00); outb(0x0a, 0xc01);
+ for(i=0;i<3;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_0, ((2+sysconf.sbdn)<<2)|i, m->apicid_bcm5785[0], 0xa); //
+ }
+
+
+
+ /* enable int */
+ /* why here? must get the BAR and PCI command bit 1 set before enable it ....*/
+ {
+ device_t dev;
+ dev = dev_find_device(0x1166, 0x0205, 0);
+ if(dev) {
+ uint32_t dword;
+ dword = pci_read_config32(dev, 0x6c);
+ dword |= (1<<4); // enable interrupts
+ pci_write_config32(dev, 0x6c, dword);
+ }
+ }
+
+//First pci-x slot (on bcm5785) under bus_bcm5785_1:d.0
+ // AIC 8130 Galileo Technology...
+ for(i=0;i<4;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_1_1, (6<<2)|i, m->apicid_bcm5785[1], 2 + (1+i)%4); //
+ }
+
+
+//pci slot (on bcm5785)
+ for(i=0;i<4;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_0, (5<<2)|i, m->apicid_bcm5785[1], 8+i%4); //
+ }
+
+
+//onboard ati
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_0, (4<<2)|0, m->apicid_bcm5785[1], 0x1);
+
+//PCI-X on bcm5780
+ for(i=0;i<4;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[1], (4<<2)|i, m->apicid_bcm5785[1], 2 + (0+i)%4); //
+ }
+
+//onboard Broadcom
+ for(i=0;i<2;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[2], (4<<2)|i, m->apicid_bcm5785[1], 0xa + (0+i)%4); //
+ }
+
+
+// First PCI-E x8
+ for(i=0;i<4;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[5], (0<<2)|i, m->apicid_bcm5785[1], 0xe); //
+ }
+
+
+// Second PCI-E x8
+ for(i=0;i<4;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[3], (0<<2)|i, m->apicid_bcm5785[1], 0xc); //
+ }
+
+// Third PCI-E x1
+ for(i=0;i<4;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[4], (0<<2)|i, m->apicid_bcm5785[1], 0xd); //
+ }
+
+/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/
+ smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, MP_APIC_ALL, 0x0);
+ smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, MP_APIC_ALL, 0x1);
+ /* There is no extension information... */
+
+ /* Compute the checksums */
+ mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
+ mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
+ printk_debug("Wrote the mp table end at: %p - %p\n",
+ mc, smp_next_mpe_entry(mc));
+ return smp_next_mpe_entry(mc);
+}
+
+unsigned long write_smp_table(unsigned long addr)
+{
+ void *v;
+ v = smp_write_floating_table(addr);
+ return (unsigned long)smp_write_config_table(v);
+}
diff --git a/src/mainboard/msi/ms9185/resourcemap.c b/src/mainboard/msi/ms9185/resourcemap.c
new file mode 100644
index 0000000000..a093e748d8
--- /dev/null
+++ b/src/mainboard/msi/ms9185/resourcemap.c
@@ -0,0 +1,291 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2003 Stefan Reinauer <stepan@coresystems.de>
+ *
+ * Copyright (C) 2006 AMD
+ * Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
+ *
+ * Copyright (C) 2006 MSI
+ * Written by bxshi <bingxunshi@gmail.com> for MSI.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+/*
+ * ms9185 needs a different resource map
+ *
+ */
+
+static void setup_ms9185_resource_map(void)
+{
+ static const unsigned int register_values[] = {
+ /* Careful set limit registers before base registers which contain the enables */
+ /* DRAM Limit i Registers
+ * F1:0x44 i = 0
+ * F1:0x4C i = 1
+ * F1:0x54 i = 2
+ * F1:0x5C i = 3
+ * F1:0x64 i = 4
+ * F1:0x6C i = 5
+ * F1:0x74 i = 6
+ * F1:0x7C i = 7
+ * [ 2: 0] Destination Node ID
+ * 000 = Node 0
+ * 001 = Node 1
+ * 010 = Node 2
+ * 011 = Node 3
+ * 100 = Node 4
+ * 101 = Node 5
+ * 110 = Node 6
+ * 111 = Node 7
+ * [ 7: 3] Reserved
+ * [10: 8] Interleave select
+ * specifies the values of A[14:12] to use with interleave enable.
+ * [15:11] Reserved
+ * [31:16] DRAM Limit Address i Bits 39-24
+ * This field defines the upper address bits of a 40 bit address
+ * that define the end of the DRAM region.
+ */
+ PCI_ADDR(0, 0x18, 1, 0x44), 0x0000f8f8, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x4C), 0x0000f8f8, 0x00000001,
+ PCI_ADDR(0, 0x18, 1, 0x54), 0x0000f8f8, 0x00000002,
+ PCI_ADDR(0, 0x18, 1, 0x5C), 0x0000f8f8, 0x00000003,
+ PCI_ADDR(0, 0x18, 1, 0x64), 0x0000f8f8, 0x00000004,
+ PCI_ADDR(0, 0x18, 1, 0x6C), 0x0000f8f8, 0x00000005,
+ PCI_ADDR(0, 0x18, 1, 0x74), 0x0000f8f8, 0x00000006,
+ PCI_ADDR(0, 0x18, 1, 0x7C), 0x0000f8f8, 0x00000007,
+ /* DRAM Base i Registers
+ * F1:0x40 i = 0
+ * F1:0x48 i = 1
+ * F1:0x50 i = 2
+ * F1:0x58 i = 3
+ * F1:0x60 i = 4
+ * F1:0x68 i = 5
+ * F1:0x70 i = 6
+ * F1:0x78 i = 7
+ * [ 0: 0] Read Enable
+ * 0 = Reads Disabled
+ * 1 = Reads Enabled
+ * [ 1: 1] Write Enable
+ * 0 = Writes Disabled
+ * 1 = Writes Enabled
+ * [ 7: 2] Reserved
+ * [10: 8] Interleave Enable
+ * 000 = No interleave
+ * 001 = Interleave on A[12] (2 nodes)
+ * 010 = reserved
+ * 011 = Interleave on A[12] and A[14] (4 nodes)
+ * 100 = reserved
+ * 101 = reserved
+ * 110 = reserved
+ * 111 = Interleve on A[12] and A[13] and A[14] (8 nodes)
+ * [15:11] Reserved
+ * [13:16] DRAM Base Address i Bits 39-24
+ * This field defines the upper address bits of a 40-bit address
+ * that define the start of the DRAM region.
+ */
+ PCI_ADDR(0, 0x18, 1, 0x40), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x48), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x50), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x58), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x60), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x68), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x70), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x78), 0x0000f8fc, 0x00000000,
+
+ /* Memory-Mapped I/O Limit i Registers
+ * F1:0x84 i = 0
+ * F1:0x8C i = 1
+ * F1:0x94 i = 2
+ * F1:0x9C i = 3
+ * F1:0xA4 i = 4
+ * F1:0xAC i = 5
+ * F1:0xB4 i = 6
+ * F1:0xBC i = 7
+ * [ 2: 0] Destination Node ID
+ * 000 = Node 0
+ * 001 = Node 1
+ * 010 = Node 2
+ * 011 = Node 3
+ * 100 = Node 4
+ * 101 = Node 5
+ * 110 = Node 6
+ * 111 = Node 7
+ * [ 3: 3] Reserved
+ * [ 5: 4] Destination Link ID
+ * 00 = Link 0
+ * 01 = Link 1
+ * 10 = Link 2
+ * 11 = Reserved
+ * [ 6: 6] Reserved
+ * [ 7: 7] Non-Posted
+ * 0 = CPU writes may be posted
+ * 1 = CPU writes must be non-posted
+ * [31: 8] Memory-Mapped I/O Limit Address i (39-16)
+ * This field defines the upp adddress bits of a 40-bit address that
+ * defines the end of a memory-mapped I/O region n
+ */
+ PCI_ADDR(0, 0x18, 1, 0x84), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x8C), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x94), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x9C), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xA4), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xAC), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xB4), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xBC), 0x00000048, 0x00ffff20,
+
+ /* Memory-Mapped I/O Base i Registers
+ * F1:0x80 i = 0
+ * F1:0x88 i = 1
+ * F1:0x90 i = 2
+ * F1:0x98 i = 3
+ * F1:0xA0 i = 4
+ * F1:0xA8 i = 5
+ * F1:0xB0 i = 6
+ * F1:0xB8 i = 7
+ * [ 0: 0] Read Enable
+ * 0 = Reads disabled
+ * 1 = Reads Enabled
+ * [ 1: 1] Write Enable
+ * 0 = Writes disabled
+ * 1 = Writes Enabled
+ * [ 2: 2] Cpu Disable
+ * 0 = Cpu can use this I/O range
+ * 1 = Cpu requests do not use this I/O range
+ * [ 3: 3] Lock
+ * 0 = base/limit registers i are read/write
+ * 1 = base/limit registers i are read-only
+ * [ 7: 4] Reserved
+ * [31: 8] Memory-Mapped I/O Base Address i (39-16)
+ * This field defines the upper address bits of a 40bit address
+ * that defines the start of memory-mapped I/O region i
+ */
+ PCI_ADDR(0, 0x18, 1, 0x80), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x88), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x90), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x98), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xA0), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xA8), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xB0), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xB8), 0x000000f0, 0x00fc0003,
+
+ /* PCI I/O Limit i Registers
+ * F1:0xC4 i = 0
+ * F1:0xCC i = 1
+ * F1:0xD4 i = 2
+ * F1:0xDC i = 3
+ * [ 2: 0] Destination Node ID
+ * 000 = Node 0
+ * 001 = Node 1
+ * 010 = Node 2
+ * 011 = Node 3
+ * 100 = Node 4
+ * 101 = Node 5
+ * 110 = Node 6
+ * 111 = Node 7
+ * [ 3: 3] Reserved
+ * [ 5: 4] Destination Link ID
+ * 00 = Link 0
+ * 01 = Link 1
+ * 10 = Link 2
+ * 11 = reserved
+ * [11: 6] Reserved
+ * [24:12] PCI I/O Limit Address i
+ * This field defines the end of PCI I/O region n
+ * [31:25] Reserved
+ */
+ PCI_ADDR(0, 0x18, 1, 0xC4), 0xFE000FC8, 0x01fff020,
+ PCI_ADDR(0, 0x18, 1, 0xCC), 0xFE000FC8, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xD4), 0xFE000FC8, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xDC), 0xFE000FC8, 0x00000000,
+
+ /* PCI I/O Base i Registers
+ * F1:0xC0 i = 0
+ * F1:0xC8 i = 1
+ * F1:0xD0 i = 2
+ * F1:0xD8 i = 3
+ * [ 0: 0] Read Enable
+ * 0 = Reads Disabled
+ * 1 = Reads Enabled
+ * [ 1: 1] Write Enable
+ * 0 = Writes Disabled
+ * 1 = Writes Enabled
+ * [ 3: 2] Reserved
+ * [ 4: 4] VGA Enable
+ * 0 = VGA matches Disabled
+ * 1 = matches all address < 64K and where A[9:0] is in the
+ * range 3B0-3BB or 3C0-3DF independen of the base & limit registers
+ * [ 5: 5] ISA Enable
+ * 0 = ISA matches Disabled
+ * 1 = Blocks address < 64K and in the last 768 bytes of eack 1K block
+ * from matching agains this base/limit pair
+ * [11: 6] Reserved
+ * [24:12] PCI I/O Base i
+ * This field defines the start of PCI I/O region n
+ * [31:25] Reserved
+ */
+ PCI_ADDR(0, 0x18, 1, 0xC0), 0xFE000FCC, 0x00000003,
+ PCI_ADDR(0, 0x18, 1, 0xC8), 0xFE000FCC, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xD0), 0xFE000FCC, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xD8), 0xFE000FCC, 0x00000000,
+
+ /* Config Base and Limit i Registers
+ * F1:0xE0 i = 0
+ * F1:0xE4 i = 1
+ * F1:0xE8 i = 2
+ * F1:0xEC i = 3
+ * [ 0: 0] Read Enable
+ * 0 = Reads Disabled
+ * 1 = Reads Enabled
+ * [ 1: 1] Write Enable
+ * 0 = Writes Disabled
+ * 1 = Writes Enabled
+ * [ 2: 2] Device Number Compare Enable
+ * 0 = The ranges are based on bus number
+ * 1 = The ranges are ranges of devices on bus 0
+ * [ 3: 3] Reserved
+ * [ 6: 4] Destination Node
+ * 000 = Node 0
+ * 001 = Node 1
+ * 010 = Node 2
+ * 011 = Node 3
+ * 100 = Node 4
+ * 101 = Node 5
+ * 110 = Node 6
+ * 111 = Node 7
+ * [ 7: 7] Reserved
+ * [ 9: 8] Destination Link
+ * 00 = Link 0
+ * 01 = Link 1
+ * 10 = Link 2
+ * 11 - Reserved
+ * [15:10] Reserved
+ * [23:16] Bus Number Base i
+ * This field defines the lowest bus number in configuration region i
+ * [31:24] Bus Number Limit i
+ * This field defines the highest bus number in configuration regin i
+ */
+ PCI_ADDR(0, 0x18, 1, 0xE0), 0x0000FC88, 0xff000203,
+ PCI_ADDR(0, 0x18, 1, 0xE4), 0x0000FC88, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xE8), 0x0000FC88, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xEC), 0x0000FC88, 0x00000000,
+ };
+
+ int max;
+ max = sizeof(register_values)/sizeof(register_values[0]);
+ setup_resource_map(register_values, max);
+}
+
diff --git a/src/southbridge/broadcom/bcm5785/bcm5785_sata.c b/src/southbridge/broadcom/bcm5785/bcm5785_sata.c
index 470bc47c73..426ee0ff0b 100644
--- a/src/southbridge/broadcom/bcm5785/bcm5785_sata.c
+++ b/src/southbridge/broadcom/bcm5785/bcm5785_sata.c
@@ -21,6 +21,8 @@ static void sata_init(struct device *dev)
uint8_t *base;
uint8_t *mmio;
struct resource *res;
+ unsigned int mmio_base;
+ volatile unsigned int *mmio_reg;
int i;
if(!(dev->path.u.pci.devfn & 7)) { // only set it in Func0
@@ -30,6 +32,21 @@ static void sata_init(struct device *dev)
res = find_resource(dev, 0x24);
base = res->base;
+
+ mmio_base = base;
+ mmio_base &= 0xfffffffc;
+ mmio_reg = (unsigned int *)( mmio_base + 0x10f0 );
+ * mmio_reg = 0x40000001;
+ mmio_reg = ( unsigned int *)( mmio_base + 0x8c );
+ * mmio_reg = 0x00ff2007;
+ mdelay( 10 );
+ * mmio_reg = 0x78592009;
+ mdelay( 10 );
+ * mmio_reg = 0x00082004;
+ mdelay( 10 );
+ * mmio_reg = 0x00002004;
+ mdelay( 10 );
+
//init PHY
printk_debug("init PHY...\n");
diff --git a/targets/msi/ms9185/Config.lb b/targets/msi/ms9185/Config.lb
new file mode 100644
index 0000000000..ef1c8d7113
--- /dev/null
+++ b/targets/msi/ms9185/Config.lb
@@ -0,0 +1,94 @@
+##
+## This file is part of the LinuxBIOS project.
+##
+## Copyright (C) 2006 MSI
+## Written by bxshi <bingxunshi@gmail.com> for MSI.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+# Sample config file for
+# the msi ms9185
+# This will make a target directory of ./ms9185
+
+target ms9185
+mainboard msi/ms9185
+
+# ms9185
+romimage "normal"
+# 36k for ATI option rom
+ option ROM_SIZE = 512*1024-36*1024
+# option ROM_SIZE = 524288
+# option ROM_SIZE = 425984
+# 64K for Etherboot
+# option ROM_SIZE = 458752
+ option USE_FALLBACK_IMAGE=0
+# option ROM_IMAGE_SIZE=0x13800
+# option ROM_IMAGE_SIZE=0x18800
+ option ROM_IMAGE_SIZE=0x20000
+# option ROM_IMAGE_SIZE=0x15800
+ option XIP_ROM_SIZE=0x40000
+ option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
+# payload ../../../payloads/tg3--ide_disk.zelf
+# payload ../../../payloads/filo.elf
+# payload ../../../payloads/filo_mem.elf
+# payload ../../../payloads/filo.zelf
+# payload ../../../payloads/tg3--filo_hda2.zelf
+# payload ../../../payloads/tg3.zelf
+# payload ../../../../payloads/tg3_vga.zelf
+# payload ../../../../payloads/tg3--filo_hda2_vga.zelf
+# payload /filo.elf
+ payload /tg3--filo.elf
+# payload ../../../../payloads/e1000_vga.zelf
+# payload ../../../../payloads/tg3--filo_hda2_vga_5_4.zelf
+# payload ../../../payloads/tg3_com2.zelf
+# payload ../../../payloads/e1000--filo.zelf
+# payload ../../../payloads/tg3--e1000--filo.zelf
+# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
+# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_5.3.zelf
+# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf
+end
+
+romimage "fallback"
+ option USE_FALLBACK_IMAGE=1
+# option ROM_IMAGE_SIZE=0x13800
+# option ROM_IMAGE_SIZE=0x19800
+ option ROM_IMAGE_SIZE=0x20000
+# option ROM_IMAGE_SIZE=0x15800
+ option XIP_ROM_SIZE=0x40000
+ option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
+# payload ../../../payloads/tg3--ide_disk.zelf
+# payload ../../../payloads/filo.elf
+# payload ../../../payloads/filo_mem.elf
+# payload ../../../payloads/filo.zelf
+# payload ../../../payloads/tg3--filo_hda2.zelf
+# payload ../../../payloads/tg3.zelf
+# payload ../../../../payloads/tg3_vga.zelf
+# payload ../../../../payloads/memtest
+# payload ../../../../payloads/e1000_vga.zelf
+# payload ../../../../payloads/filo_hda.zelf
+# payload ../../../../payloads/tg3--filo_hda2_vga.zelf
+# payload /filo.elf
+ payload /tg3--filo.elf
+# payload ../../../../payloads/tg3--filo_hda2_vga_5_4.zelf
+# payload ../../../payloads/tg3_com2.zelf
+# payload ../../../payloads/e1000--filo.zelf
+# payload ../../../payloads/tg3--e1000--filo.zelf
+# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
+# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_5.3.zelf
+# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf
+end
+
+buildrom ./ms9185.lxb ROM_SIZE "normal" "fallback"