diff options
| -rw-r--r-- | src/mainboard/arima/hdama/Config.lb | 385 | ||||
| -rw-r--r-- | src/mainboard/arima/hdama/Options.lb | 124 | ||||
| -rw-r--r-- | targets/arima/hdama/Config.lb | 85 | ||||
| -rw-r--r-- | util/newconfig/config.g | 87 |
4 files changed, 256 insertions, 425 deletions
diff --git a/src/mainboard/arima/hdama/Config.lb b/src/mainboard/arima/hdama/Config.lb index f8091bdbe8..c5ed005f80 100644 --- a/src/mainboard/arima/hdama/Config.lb +++ b/src/mainboard/arima/hdama/Config.lb @@ -1,127 +1,3 @@ -uses HAVE_MP_TABLE -uses HAVE_PIRQ_TABLE -uses USE_FALLBACK_IMAGE -uses HAVE_FALLBACK_BOOT -uses HAVE_HARD_RESET -uses HARD_RESET_BUS -uses HARD_RESET_DEVICE -uses HARD_RESET_FUNCTION -uses IRQ_SLOT_COUNT -uses HAVE_OPTION_TABLE -uses CONFIG_MAX_CPUS -uses CONFIG_IOAPIC -uses CONFIG_SMP -uses FALLBACK_SIZE -uses ROM_SIZE -uses ROM_SECTION_SIZE -uses ROM_IMAGE_SIZE -uses ROM_SECTION_SIZE -uses ROM_SECTION_OFFSET -uses CONFIG_ROM_STREAM -uses CONFIG_ROM_STREAM_START -uses PAYLOAD_SIZE -uses _ROMBASE -uses XIP_ROM_SIZE -uses XIP_ROM_BASE -uses STACK_SIZE -uses HEAP_SIZE -uses USE_OPTION_TABLE -uses LB_CKS_RANGE_START -uses LB_CKS_RANGE_END -uses LB_CKS_LOC -uses MAINBOARD_PART_NUMBER -uses MAINBOARD_VENDOR -uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID -uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID - - -## ROM_SIZE is the size of boot ROM that this board will use. -default ROM_SIZE=524288 - -### -### Build options -### - -## -## Build code for the fallback boot -## -default HAVE_FALLBACK_BOOT=1 - -## -## Build code to reset the motherboard from linuxBIOS -## -default HAVE_HARD_RESET=1 - -default HARD_RESET_BUS=1 -default HARD_RESET_DEVICE=4 -default HARD_RESET_FUNCTION=0 - -## -## Build code to export a programmable irq routing table -## -default HAVE_PIRQ_TABLE=1 -default IRQ_SLOT_COUNT=9 - -## -## Build code to export an x86 MP table -## Useful for specifying IRQ routing values -## -default HAVE_MP_TABLE=1 - -## -## Build code to export a CMOS option table -## -default HAVE_OPTION_TABLE=1 - -## -## Move the default LinuxBIOS cmos range off of AMD RTC registers -## -default LB_CKS_RANGE_START=49 -default LB_CKS_RANGE_END=122 -default LB_CKS_LOC=123 - -## -## Build code for SMP support -## Only worry about 2 micro processors -## -default CONFIG_SMP=1 -default CONFIG_MAX_CPUS=2 - -## -## Build code to setup a generic IOAPIC -## -default CONFIG_IOAPIC=1 - -## -## Clean up the motherboard id strings -## -default MAINBOARD_PART_NUMBER="HDAMA" -default MAINBOARD_VENDOR="ARIMA" -default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f -default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016 - -### -### LinuxBIOS layout values -### - -## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. -default ROM_IMAGE_SIZE = 65536 - -## -## Use a small 8K stack -## -default STACK_SIZE=0x2000 - -## -## Use a small 32K heap -## -default HEAP_SIZE=0x8000 - -## -## Only use the option table in a normal image -## -default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE - ## ## Compute the location and size of where this firmware image ## (linuxBIOS plus bootloader) will live in the boot rom chip. @@ -157,203 +33,72 @@ default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE ) default XIP_ROM_SIZE=65536 default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) -## -## Set all of the defaults for an x86 architecture -## - -arch i386 end - -## -## Build the objects we have code for in this directory. -## - -driver mainboard.o -if HAVE_MP_TABLE object mptable.o end -if HAVE_PIRQ_TABLE object irq_tables.o end - -## -## Romcc output -## -makerule ./failover.E - depends "$(MAINBOARD)/failover.c" - action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E" -end - -makerule ./failover.inc - depends "./failover.E ./romcc" - action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E" -end - -makerule ./auto.E - depends "$(MAINBOARD)/auto.c option_table.h " - action "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E" -end -makerule ./auto.inc - depends "./auto.E ./romcc" - action "./romcc -mcpu=k8 -O2 ./auto.E > auto.inc" -end - -## -## Build our 16 bit and 32 bit linuxBIOS entry code -## -mainboardinit cpu/x86/16bit/entry16.inc -mainboardinit cpu/x86/32bit/entry32.inc -ldscript /cpu/x86/16bit/entry16.lds -ldscript /cpu/x86/32bit/entry32.lds - -## -## Build our reset vector (This is where linuxBIOS is entered) -## -if USE_FALLBACK_IMAGE - mainboardinit cpu/x86/16bit/reset16.inc - ldscript /cpu/x86/16bit/reset16.lds -else - mainboardinit cpu/x86/32bit/reset32.inc - ldscript /cpu/x86/32bit/reset32.lds -end - -### Should this be in the northbridge code? -mainboardinit arch/i386/lib/cpu_reset.inc - -## -## Include an id string (For safe flashing) -## -mainboardinit arch/i386/lib/id.inc -ldscript /arch/i386/lib/id.lds - -### -### This is the early phase of linuxBIOS startup -### Things are delicate and we test to see if we should -### failover to another image. -### -if USE_FALLBACK_IMAGE - ldscript /arch/i386/lib/failover.lds - mainboardinit ./failover.inc -end - -### -### O.k. We aren't just an intermediary anymore! -### - -## -## Setup RAM -## -mainboardinit cpu/x86/fpu/enable_fpu.inc -mainboardinit cpu/x86/mmx/enable_mmx.inc -mainboardinit cpu/x86/sse/enable_sse.inc -mainboardinit ./auto.inc -mainboardinit cpu/x86/sse/disable_sse.inc -mainboardinit cpu/x86/mmx/disable_mmx.inc - -## -## Include the secondary Configuration files -## -dir /pc80 -config chip.h - -northbridge amd/amdk8 "mc0" - pnp cf8.0 - northbridge amd/amdk8 "mc1" link 0 - pci 0:19.0 - pci 0:19.0 - pci 0:19.0 - pci 0:19.1 - pci 0:19.2 - pci 0:19.3 - end - pci 1:18.0 - southbridge amd/amd8131 "amd8131" link 1 - pci 0:0.0 - pci 0:0.1 - pci 0:1.0 - pci 0:1.1 - end - southbridge amd/amd8111 "amd8111" link 1 - pci 0:0.0 - pci 0:1.0 on - superio NSC/pc87360 link 1 - pnp 2e.0 off # Floppy - io 0x60 = 0x3f0 - irq 0x70 = 6 - drq 0x74 = 2 - pnp 2e.1 off # Parallel Port - io 0x60 = 0x378 - irq 0x70 = 7 - pnp 2e.2 off # Com 2 - io 0x60 = 0x2f8 - irq 0x70 = 3 - pnp 2e.3 on # Com 1 - io 0x60 = 0x3f8 - irq 0x70 = 4 - pnp 2e.4 off # SWC - pnp 2e.5 off # Mouse - pnp 2e.6 on # Keyboard - io 0x60 = 0x60 - io 0x62 = 0x64 - irq 0x70 = 1 - pnp 2e.7 off # GPIO - pnp 2e.8 off # ACB - pnp 2e.9 off # FSCM - pnp 2e.a off # WDT - end - pci 0:1.1 on - pci 0:1.2 on - pci 0:1.3 on # ACPI/SMBUS - chip drivers/generic/generic link 4 - #phillips pca9545 smbus mux - i2c 70 - # analog_devices adm1026 - chip drivers/generic/generic link 0 - i2c 2c - end - i2c 70 - i2c 70 - i2c 70 - end - chip drivers/generic/generic link 4 #dimm 0-0-0 - i2c 50 +# sample config for arima/hdama +chip northbridge/amd/amdk8 + print "HI MOM!\n" + device pnp cf8.0 on # cf8 config + print "HI MOM!\n" + device pci 18.0 on # northbridge + print "HI MOM!\n" + # devices on link 0, link 0 == LDT 0 + chip southbridge/amd/amd8131 + print "SOUTH\n" + # the on/off keyword is mandatory + device pci 0.0 on end + print "SOUTH2\n" + device pci 0.1 on end + print "SOUTH3\n" + device pci 1.0 on end + print "SOUTH4\n" + device pci 1.1 on end end - chip drivers/generic/generic link 4 #dimm 0-0-1 - i2c 51 - end - chip drivers/generic/generic link 4 #dimm 0-1-0 - i2c 52 - end - chip drivers/generic/generic link 4 #dimm 0-1-1 - i2c 53 - end - chip drivers/generic/generic link 4 #dimm 1-0-0 - i2c 54 + chip southbridge/amd/amd8111 + print "NEXT SOUTH\n" + # this "device pci 0.0" is the parent the next one + # PCI bridge + device pci 0.0 on + # this "device pci 0.0" is a child of the + # previous one + # devices behind the bridge + device pci 0.0 on end + device pci 0.1 on end + device pci 0.2 on end + # the device statement can span across multiple + # lines too + device pci 1.0 + off + end + end + device pci 1.0 on + chip superio/NSC/pc87360 + device pnp 2e.3 on + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + end + end + device pci 1.1 on end + device pci 1.2 off end + device pci 1.3 off end + device pci 1.5 on end + device pci 1.6 on end end - chip drivers/generic/generic link 4 #dimm 1-0-1 - i2c 55 - end - chip drivers/generic/generic link 4 #dimm 1-1-0 - i2c 56 - end - chip drivers/generic/generic link 4 #dimm 1-1-1 - i2c 57 - end - pci 0:1.5 off - pci 0:1.6 off - pci 1:0.0 on - pci 1:0.1 on - pci 1:0.2 on - pci 1:1.0 off - end - pci 1:18.0 - pci 1:18.0 - pci 1:18.1 - pci 1:18.2 - pci 1:18.3 -end - - -cpu amd/socket_940 "cpu0" link 1 - apic 0 -end - -cpu amd/socket_940 "cpu1" link 1 - apic 1 + end # device pci 18.0 + device pci 18.0 on + # some non-existence devices on link 1 + end + device pci 18.0 on + # some non-existence devices on link 2 + end + device pci 18.1 + # empty + end + device pci 18.2 + # empty + end + device pci 18.3 + # empty + end + end # device pnp end diff --git a/src/mainboard/arima/hdama/Options.lb b/src/mainboard/arima/hdama/Options.lb new file mode 100644 index 0000000000..f2c2dba2bb --- /dev/null +++ b/src/mainboard/arima/hdama/Options.lb @@ -0,0 +1,124 @@ +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses HARD_RESET_BUS +uses HARD_RESET_DEVICE +uses HARD_RESET_FUNCTION +uses IRQ_SLOT_COUNT +uses HAVE_OPTION_TABLE +uses CONFIG_MAX_CPUS +uses CONFIG_IOAPIC +uses CONFIG_SMP +uses FALLBACK_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_STREAM +uses CONFIG_ROM_STREAM_START +uses PAYLOAD_SIZE +uses _ROMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses STACK_SIZE +uses HEAP_SIZE +uses USE_OPTION_TABLE +uses LB_CKS_RANGE_START +uses LB_CKS_RANGE_END +uses LB_CKS_LOC +uses MAINBOARD_PART_NUMBER +uses MAINBOARD_VENDOR +uses MAINBOARD +uses LINUXBIOS_EXTRA_VERSION +uses _RAMBASE + + +## ROM_SIZE is the size of boot ROM that this board will use. +default ROM_SIZE=524288 + +### +### Build options +### + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=1 + +default HARD_RESET_BUS=1 +default HARD_RESET_DEVICE=4 +default HARD_RESET_FUNCTION=0 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=1 +default IRQ_SLOT_COUNT=9 + +## +## Build code to export an x86 MP table +## Useful for specifying IRQ routing values +## +default HAVE_MP_TABLE=1 + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=1 + +## +## Move the default LinuxBIOS cmos range off of AMD RTC registers +## +default LB_CKS_RANGE_START=49 +default LB_CKS_RANGE_END=122 +default LB_CKS_LOC=123 + +## +## Build code for SMP support +## Only worry about 2 micro processors +## +default CONFIG_SMP=1 +default CONFIG_MAX_CPUS=2 + +## +## Build code to setup a generic IOAPIC +## +default CONFIG_IOAPIC=1 + +## +## Clean up the motherboard id strings +## +default MAINBOARD_PART_NUMBER="HDAMA" +default MAINBOARD_VENDOR="ARIMA" + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 65536 + +## +## Use a small 8K stack +## +default STACK_SIZE=0x2000 + +## +## Use a small 16K heap +## +default HEAP_SIZE=0x4000 + +## +## Only use the option table in a normal image +## +default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE +default _RAMBASE=0x00004000 +end diff --git a/targets/arima/hdama/Config.lb b/targets/arima/hdama/Config.lb index 51d00fb3c4..350c2b0857 100644 --- a/targets/arima/hdama/Config.lb +++ b/targets/arima/hdama/Config.lb @@ -2,97 +2,15 @@ # the Arima HDAMA # This will make a target directory of ./hdama -loadoptions target hdama +mainboard arima/hdama -uses ARCH -uses CONFIG_COMPRESS -uses CONFIG_IOAPIC -uses CONFIG_ROM_STREAM -uses CONFIG_ROM_STREAM_START -uses CONFIG_UDELAY_TSC -uses CPU_FIXUP -uses FALLBACK_SIZE -uses HAVE_FALLBACK_BOOT -uses HAVE_MP_TABLE -uses HAVE_PIRQ_TABLE -uses HAVE_HARD_RESET -uses i586 -uses i686 -uses INTEL_PPRO_MTRR -uses HEAP_SIZE -uses IRQ_SLOT_COUNT -uses k7 -uses k8 -uses MAINBOARD_PART_NUMBER -uses MAINBOARD_VENDOR -uses CONFIG_SMP -uses CONFIG_MAX_CPUS -uses MEMORY_HOLE -uses PAYLOAD_SIZE -uses _RAMBASE -uses _ROMBASE -uses ROM_IMAGE_SIZE -uses ROM_SECTION_OFFSET -uses ROM_SECTION_SIZE -uses ROM_SIZE -uses STACK_SIZE -uses USE_FALLBACK_IMAGE -uses USE_OPTION_TABLE -uses HAVE_OPTION_TABLE -uses MAXIMUM_CONSOLE_LOGLEVEL -uses DEFAULT_CONSOLE_LOGLEVEL -uses CONFIG_CONSOLE_SERIAL8250 -uses MAINBOARD -uses CONFIG_CHIP_CONFIGURE -uses XIP_ROM_SIZE -uses XIP_ROM_BASE -uses LINUXBIOS_EXTRA_VERSION - -option CONFIG_CHIP_CONFIGURE=1 - -option MAXIMUM_CONSOLE_LOGLEVEL=8 -option DEFAULT_CONSOLE_LOGLEVEL=8 -option CONFIG_CONSOLE_SERIAL8250=1 - -option CPU_FIXUP=1 -option CONFIG_UDELAY_TSC=0 -option i686=1 -option i586=1 -option INTEL_PPRO_MTRR=1 -option k7=1 -option k8=1 - -option ROM_SIZE=524288 - - -option HAVE_OPTION_TABLE=1 -option CONFIG_ROM_STREAM=1 -option HAVE_FALLBACK_BOOT=1 - -### -### Compute the location and size of where this firmware image -### (linuxBIOS plus bootloader) will live in the boot rom chip. -### -option FALLBACK_SIZE=131072 - -## LinuxBIOS C code runs at this location in RAM -option _RAMBASE=0x00004000 - -# -### -### Compute the start location and size size of -### The linuxBIOS bootloader. -### - -# # Arima hdama romimage "normal" option USE_FALLBACK_IMAGE=0 option ROM_IMAGE_SIZE=0x10000 option LINUXBIOS_EXTRA_VERSION=".0Normal" - mainboard arima/hdama payload /usr/share/etherboot/5.2.1eb1-lnxi-lb/tg3--ide_disk.zelf end @@ -100,7 +18,6 @@ romimage "fallback" option USE_FALLBACK_IMAGE=1 option ROM_IMAGE_SIZE=0x10000 option LINUXBIOS_EXTRA_VERSION=".0Fallback" - mainboard arima/hdama payload /usr/share/etherboot/5.2.1eb1-lnxi-lb/tg3--ide_disk.zelf # use this to test a build if you don't have the etherboot # payload /etc/hosts diff --git a/util/newconfig/config.g b/util/newconfig/config.g index ffe32c3a2f..65cedb6b5c 100644 --- a/util/newconfig/config.g +++ b/util/newconfig/config.g @@ -12,6 +12,7 @@ errors = 0 target_dir = '' target_name = '' treetop = '' +full_mainboard_path = '' global_options = {} global_options_by_order = [] global_option_values = {} @@ -841,6 +842,7 @@ def newoptionvalue(name, image): def getoptionvalue(name, op, image): global global_option_values + #print "getoptionvalue name %s op %s image %s\n" % (name, op,image) if (op == 0): fatal("Option %s undefined (missing use command?)" % name) if (image): @@ -856,12 +858,16 @@ def getoption(name, image): global global_uses_options, alloptions, curimage + #print "getoption: name %s image %s alloptions %s curimage %s\n\n" % (name, image, alloptions, curimage) curpart = partstack.tos() if (alloptions): + #print "ALLOPTIONS\n" o = getdict(global_options, name) elif (curpart): + #print "CURPART\n" o = getdict(curpart.uses_options, name) else: + #print "GLOBAL_USES_OPTIONS\n" o = getdict(global_uses_options, name) v = getoptionvalue(name, o, image) if (v == 0): @@ -1057,12 +1063,12 @@ def validdef(name, defval): if ((defval & 4) != 4): fatal("Must specify comment for option %s" % name) -def loadoptions(): - file = os.path.join('src', 'config', 'Options.lb') +def loadoptions(path, file, rule): + file = os.path.join('src', path, file) optionsfile = os.path.join(treetop, file) fp = safe_open(optionsfile, 'r') loc.push(file) - if (not parse('options', fp.read())): + if (not parse(rule, fp.read())): fatal("Could not parse file") loc.pop() @@ -1112,7 +1118,7 @@ def payload(path): def startromimage(name): global romimages, curimage, target_dir, target_name - print "Configuring ROMIMAGE %s" % name + print "Configuring ROMIMAGE %s Curimage %s" % (name, curimage) o = getdict(romimages, name) if (o): fatal("romimage %s previously defined" % name) @@ -1124,19 +1130,29 @@ def startromimage(name): def endromimage(): global curimage + mainboard() print "End ROMIMAGE" curimage = 0 #curpart = 0 -def mainboard(path): - full_path = os.path.join(treetop, 'src', 'mainboard', path) +def mainboardsetup(path): + global full_mainboard_path + mainboard_path = os.path.join('mainboard', path) + loadoptions(mainboard_path, 'Options.lb', 'mainboardvariables') + full_mainboard_path = os.path.join(treetop, 'src', 'mainboard', path) vendor = re.sub("/.*", "", path) part_number = re.sub("[^/]*/", "", path) - setdefault('MAINBOARD', full_path, 0) + setdefault('MAINBOARD', full_mainboard_path, 0) setdefault('MAINBOARD_VENDOR', vendor, 0) setdefault('MAINBOARD_PART_NUMBER', part_number, 0) - dodir('/config', 'Config.lb') - part('mainboard', path, 'Config.lb', 0, 0) + +def mainboard(): + # a mainboard is no longer really a part as such. + # so just do the config file for the mainboard + #part('mainboard', full_mainboard_path, 'Config.lb', 0, 0) + global full_mainboard_path + mainboard_path = os.path.join(full_mainboard_path) + loadoptions(mainboard_path, 'Config.lb', 'cfgfile') curimage.setroot(partstack.tos()) partpop() @@ -1177,6 +1193,16 @@ def cpudir(path): dodir(srcdir, "Config.lb") cpu_type = path +def simplepart(type): + global curimage, dirstack, partstack + newpart = partobj(curimage, 0, partstack.tos(), type, \ + '', 0, 0) + print "Configuring PART %s" % (type) + partstack.push(newpart) + print " new PART tos is now %s\n" %partstack.tos() + # just push TOS, so that we can pop later. + dirstack.push(dirstack.tos()) + def part(type, path, file, name, link): global curimage, dirstack, partstack partdir = os.path.join(type, path) @@ -1187,6 +1213,7 @@ def part(type, path, file, name, link): type_name, name, link) print "Configuring PART %s, path %s" % (type, path) partstack.push(newpart) + print " new PART tos is now %s\n" %partstack.tos() dirstack.push(fulldir) # special case for 'cpu' parts. # we could add a new function too, but this is rather trivial. @@ -1209,6 +1236,7 @@ def partpop(): notice("Option %s using default value %s" % (op, getformated(op, curpart.image))) partstack.pop() dirstack.pop() + print "partstack.pop, TOS is now %s\n" % partstack.tos() def dodir(path, file): """dodir is like part but there is no new part""" @@ -1334,6 +1362,7 @@ parser Config: token DEFAULT: 'default' token DEFINE: 'define' token DEPENDS: 'depends' + token DEVICE: 'device' token DIR: 'dir' token DRIVER: 'driver' token DRQ: 'drq' @@ -1514,26 +1543,32 @@ parser Config: {{ if (C): partstack.tos().end_resources() }} - rule pci<<C>>: PCI HEX_NUM {{ bus = int(HEX_NUM,16) }} - ':' HEX_NUM {{ slot = int(HEX_NUM,16) }} + rule pci<<C>>: PCI {{ if (C): simplepart('pci') }} + + HEX_NUM {{ slot = int(HEX_NUM,16) }} '.' HEX_NUM {{ function = int(HEX_NUM, 16) }} enable - {{ if (C): partstack.tos().addpcipath(enable, bus, slot, function) }} + {{ if (C): partstack.tos().addpcipath(enable, 0, slot, function) }} resources<<C>> + partend<<C>> - rule pnp<<C>>: PNP HEX_NUM {{ port = int(HEX_NUM,16) }} + rule pnp<<C>>: PNP {{ if (C): simplepart('pnp') }} + HEX_NUM {{ port = int(HEX_NUM,16) }} '.' HEX_NUM {{ device = int(HEX_NUM, 16) }} enable {{ if (C): partstack.tos().addpnppath(enable, port, device) }} resources<<C>> + partend<<C>> - rule i2c<<C>>: I2C HEX_NUM {{ device = int(HEX_NUM, 16) }} + rule i2c<<C>>: I2C {{ if (C): simplepart('i2c') }} + HEX_NUM {{ device = int(HEX_NUM, 16) }} enable {{ if (C): partstack.tos().addi2cpath(enable, device) }} resources<<C>> - rule apic<<C>>: APIC HEX_NUM {{ apic_id = int(HEX_NUM, 16) }} + rule apic<<C>>: APIC {{ if (C): simplepart('apic') }} + HEX_NUM {{ apic_id = int(HEX_NUM, 16) }} enable {{ if (C): partstack.tos().addapicpath(enable, apic_id) }} resources<<C>> @@ -1558,6 +1593,8 @@ parser Config: rule config<<C>>: CONFIG PATH {{ if (C): addconfig(PATH) }} + rule device<<C>>: DEVICE dev_path<<C>> + rule stmt<<C>>: arch<<C>> {{ return arch}} | addaction<<C>> {{ return addaction }} | config<<C>> {{ return config}} @@ -1577,17 +1614,26 @@ parser Config: | partdef<<C>> {{ return partdef }} | prtstmt<<C>> {{ return prtstmt }} | register<<C>> {{ return register }} - | dev_path<<C>> {{ return dev_path }} + | device<<C>> {{ return device }} # ENTRY for parsing Config.lb file rule cfgfile: (uses<<1>>)* (stmt<<1>>)* EOF {{ return 1 }} + rule cfgfile: (uses<<1>>)* + (stmt<<1>>)* + EOF {{ return 1 }} + rule usesid<<C>>: ID {{ if (C): usesoption(ID) }} rule uses<<C>>: USES (usesid<<C>>)+ + rule mainboardvariables: (uses<<1>>)* + (default<<1>>)* + (option<<1>>)* + END {{ return 1}} + rule value: STR {{ return dequote(STR) }} | expr {{ return expr }} | DELEXPR {{ return DELEXPR }} @@ -1605,8 +1651,8 @@ parser Config: rule payload<<C>>: PAYLOAD DIRPATH {{ if (C): payload(DIRPATH) }} - rule mainboard<<C>>: - MAINBOARD PATH {{ if (C): mainboard(PATH) }} + rule mainboard: + MAINBOARD PATH {{ mainboardsetup(PATH) }} rule romif<<C>>: IF ID {{ c = lookup(ID) }} (romstmt<<C and c>>)* @@ -1615,7 +1661,6 @@ parser Config: rule romstmt<<C>>: romif<<C>> | option<<C>> - | mainboard<<C>> | payload<<C>> rule romimage: ROMIMAGE STR {{ startromimage(dequote(STR)) }} @@ -1633,9 +1678,9 @@ parser Config: | opstmt<<1>> # ENTRY for parsing root part - rule board: LOADOPTIONS {{ loadoptions() }} + rule board: {{ loadoptions("config", "Options.lb", "options") }} TARGET DIRPATH {{ target(DIRPATH) }} - (uses<<1>>)* + mainboard (romstmts)* EOF {{ return 1 }} |