diff options
| -rw-r--r-- | src/mainboard/msi/ms9185/Config.lb | 299 | ||||
| -rw-r--r-- | src/mainboard/msi/ms9185/Options.lb | 332 | ||||
| -rw-r--r-- | src/mainboard/msi/ms9185/cache_as_ram_auto.c | 375 | ||||
| -rw-r--r-- | src/mainboard/msi/ms9185/chip.h | 28 | ||||
| -rw-r--r-- | src/mainboard/msi/ms9185/cmos.layout | 98 | ||||
| -rw-r--r-- | src/mainboard/msi/ms9185/get_bus_conf.c | 144 | ||||
| -rw-r--r-- | src/mainboard/msi/ms9185/irq_tables.c | 126 | ||||
| -rw-r--r-- | src/mainboard/msi/ms9185/mainboard.c | 33 | ||||
| -rw-r--r-- | src/mainboard/msi/ms9185/mb_sysconf.h | 40 | ||||
| -rw-r--r-- | src/mainboard/msi/ms9185/mptable.c | 205 | ||||
| -rw-r--r-- | src/mainboard/msi/ms9185/resourcemap.c | 291 | ||||
| -rw-r--r-- | src/southbridge/broadcom/bcm5785/bcm5785_sata.c | 17 | ||||
| -rw-r--r-- | targets/msi/ms9185/Config.lb | 94 |
13 files changed, 2082 insertions, 0 deletions
diff --git a/src/mainboard/msi/ms9185/Config.lb b/src/mainboard/msi/ms9185/Config.lb new file mode 100644 index 0000000000..34c48d1f5f --- /dev/null +++ b/src/mainboard/msi/ms9185/Config.lb @@ -0,0 +1,299 @@ +## +## This file is part of the LinuxBIOS project. +## +## Copyright (C) 2006 AMD +## Written by Yinghai Lu <yinghailu@gmail.com> for AMD. +## +## Copyright (C) 2006 MSI +## Written by bxshi <bingxunshi@gmail.com> for MSI. +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; either version 2 of the License, or +## (at your option) any later version. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +## +## Compute the location and size of where this firmware image +## (linuxBIOS plus bootloader) will live in the boot rom chip. +## +if USE_FALLBACK_IMAGE + default ROM_SECTION_SIZE = FALLBACK_SIZE + default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) +else + default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) + default ROM_SECTION_OFFSET = 0 +end + +## +## Compute the start location and size size of +## The linuxBIOS bootloader. +## +default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) +default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) + +## +## Compute where this copy of linuxBIOS will start in the boot rom +## +default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE ) + +## +## Compute a range of ROM that can cached to speed up linuxBIOS, +## execution speed. +## +## XIP_ROM_SIZE must be a power of 2. +## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE +## +default XIP_ROM_SIZE=65536 +default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) + +arch i386 end + +## +## Build the objects we have code for in this directory. +## + +driver mainboard.o + +#dir /drivers/si/3114 + +#needed by irq_tables and mptable and acpi_tables +object get_bus_conf.o + +if HAVE_MP_TABLE + object mptable.o +end + +if HAVE_PIRQ_TABLE + object irq_tables.o +end + +if USE_DCACHE_RAM + + if CONFIG_USE_INIT + # compile cache_as_ram.c to auto.o + makerule ./cache_as_ram_auto.o + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o $@" + end + + else + #compile cache_as_ram.c to auto.inc + makerule ./cache_as_ram_auto.inc + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@" + action "perl -e 's/.rodata/.rom.data/g' -pi $@" + action "perl -e 's/.text/.section .rom.text/g' -pi $@" + end + + end +end +## +## Build our 16 bit and 32 bit linuxBIOS entry code +## + +if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/entry16.inc + ldscript /cpu/x86/16bit/entry16.lds +end + +mainboardinit cpu/x86/32bit/entry32.inc +if USE_DCACHE_RAM + if CONFIG_USE_INIT + ldscript /cpu/x86/32bit/entry32.lds + end + + if CONFIG_USE_INIT + ldscript /cpu/amd/car/cache_as_ram.lds + end +end + +## +## Build our reset vector (This is where linuxBIOS is entered) +## +if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds +else + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds +end + +## +## Include an id string (For safe flashing) +## +mainboardinit arch/i386/lib/id.inc +ldscript /arch/i386/lib/id.lds + +if USE_DCACHE_RAM + ## + ## Setup Cache-As-Ram + ## + mainboardinit cpu/amd/car/cache_as_ram.inc +end + +### +### This is the early phase of linuxBIOS startup +### Things are delicate and we test to see if we should +### failover to another image. +### +if USE_FALLBACK_IMAGE + if USE_DCACHE_RAM + ldscript /arch/i386/lib/failover.lds + end +end + +### +### O.k. We aren't just an intermediary anymore! +### + +## +## Setup RAM +## +if USE_DCACHE_RAM + + if CONFIG_USE_INIT + initobject cache_as_ram_auto.o + else + mainboardinit ./cache_as_ram_auto.inc + end + +end + +## +## Include the secondary Configuration files +## +if CONFIG_CHIP_NAME + config chip.h +end + +# sample config for amd/serengeti_cheetah +chip northbridge/amd/amdk8/root_complex + device apic_cluster 0 on + chip cpu/amd/socket_F + device apic 0 on end + end + end + device pci_domain 0 on + chip northbridge/amd/amdk8 + device pci 18.0 on end + device pci 18.0 on end + device pci 18.0 on # northbridge + # devices on link 0 + chip southbridge/broadcom/bcm5780 # HT2000 + device pci 0.0 on end # PXB 1 0x0130 + device pci 1.0 on # PXB 2 0x0130 + device pci 4.0 on end # GB E 0x1668 vid = 0x14e4 + device pci 4.1 on end # GB E 0x1669 vid = 0x14e4 + end + device pci 2.0 on end # PCI E 1 #0x0132 + device pci 3.0 on end # PCI E 2 + device pci 4.0 on end # PCI E 3 + device pci 5.0 on end # PCI E 4 + end + chip southbridge/broadcom/bcm5785 # HT1000 + device pci 0.0 on # HT PXB 0x0036 + device pci d.0 on end # PPBX 0x0104 + device pci e.0 on end # SATA 0x024a + device pci e.1 on end # SATA 0x024a bx_a001 + device pci e.2 on end # SATA 0x024a bx_a001 + device pci e.3 on end # SATA 0x024a bx_a001 + end + device pci 1.0 on # Legacy pci main 0x0205 + end + device pci 1.1 on end # IDE 0x0214 + device pci 1.2 on # LPC 0x0234 + chip superio/nsc/pc87417 + device pnp 2e.0 off # Floppy + io 0x60 = 0x3f0 + irq 0x70 = 6 + drq 0x74 = 2 + end + device pnp 2e.1 off # Parallel Port + io 0x60 = 0x378 + irq 0x70 = 7 + end + device pnp 2e.2 off # Com 2 + io 0x60 = 0x2f8 + irq 0x70 = 3 + end + device pnp 2e.3 on # Com 1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + device pnp 2e.4 off end # SWC + device pnp 2e.5 off end # Mouse + device pnp 2e.6 on # Keyboard + io 0x60 = 0x60 + io 0x62 = 0x64 + irq 0x70 = 1 + end + device pnp 2e.7 off end # GPIO + device pnp 2e.f off end # XBUS + device pnp 2e.10 on #RTC + io 0x60 = 0x70 + io 0x62 = 0x72 + end + end + end + device pci 1.3 on end # WDTimer 0x0238 + device pci 1.4 on end # XIOAPIC0 0x0235 + device pci 1.5 on end # XIOAPIC1 + device pci 1.6 on end # XIOAPIC2 + device pci 2.0 on end # USB 0x0223 + device pci 2.1 on end # USB + device pci 2.2 on end # USB + #when HT_CHAIN_END_UNITID_BASE (0,1) < HT_CHAIN_UNITID_BASE (6,,,,), + chip drivers/pci/onboard + device pci 3.0 on end # it is in bcm5785_0 bus, but the device id can not be changed even unitid is changed, fake one to get the rom_address + # if HT_CHAIN_END_UNITID_BASE=0, it is 4, if HT_CHAIN_END_UNITID_BASE=1, it is 3 + register "rom_address" = "0xfff80000" + end + #bx_a013+ start + #chip drivers/pci/onboard #SATA2 + # device pci 5.0 on end + # device pci 5.1 on end + # device pci 5.2 on end + # device pci 5.3 on end + #end + #bx_a013+ end + + end + #when HT_CHAIN_END_UNITID_BASE > HT_CHAIN_UNITID_BASE (6, ,,,,) +# chip drivers/pci/onboard +# device pci 0.0 on end # fake, will be disabled +# end +# chip drivers/pci/onboard +# device pci 4.0 on end # it is in bcm5785_0 bus, but the device id can not be changed even unitid is changed +# register "rom_address" = "0xfff80000" +# end + + end # device pci 18.0 + device pci 18.1 on end + device pci 18.2 on end + device pci 18.3 on end + end # amdk8 + end #pci_domain +# chip drivers/generic/debug +# device pnp 0.0 off end # chip name +# device pnp 0.1 on end # pci_regs_all +# device pnp 0.2 off end # mem +# device pnp 0.3 off end # cpuid +# device pnp 0.4 off end # smbus_regs_all +# device pnp 0.5 off end # dual core msr +# device pnp 0.6 off end # cache size +# device pnp 0.7 off end # tsc +# end + +end + + diff --git a/src/mainboard/msi/ms9185/Options.lb b/src/mainboard/msi/ms9185/Options.lb new file mode 100644 index 0000000000..da8eee4f3a --- /dev/null +++ b/src/mainboard/msi/ms9185/Options.lb @@ -0,0 +1,332 @@ +## +## This file is part of the LinuxBIOS project. +## +## Copyright (C) 2006 AMD +## Written by Yinghai Lu <yinghailu@gmail.com> for AMD. +## +## Copyright (C) 2006 MSI +## Written by bxshi <bingxunshi@gmail.com> for MSI. +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; either version 2 of the License, or +## (at your option) any later version. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses HAVE_ACPI_TABLES +uses ACPI_SSDTX_NUM +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses IRQ_SLOT_COUNT +uses HAVE_OPTION_TABLE +uses CONFIG_MAX_CPUS +uses CONFIG_MAX_PHYSICAL_CPUS +uses CONFIG_LOGICAL_CPUS +uses CONFIG_IOAPIC +uses CONFIG_SMP +uses FALLBACK_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_STREAM +uses CONFIG_ROM_STREAM_START +uses PAYLOAD_SIZE +uses _ROMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses STACK_SIZE +uses HEAP_SIZE +uses USE_OPTION_TABLE +uses LB_CKS_RANGE_START +uses LB_CKS_RANGE_END +uses LB_CKS_LOC +uses MAINBOARD_PART_NUMBER +uses MAINBOARD_VENDOR +uses MAINBOARD +uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID +uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID +uses LINUXBIOS_EXTRA_VERSION +uses _RAMBASE +uses TTYS0_BAUD +uses TTYS0_BASE +uses TTYS0_LCS +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL +uses CONFIG_CONSOLE_SERIAL8250 +uses HAVE_INIT_TIMER +uses CONFIG_GDB_STUB +uses CONFIG_GDB_STUB +uses CROSS_COMPILE +uses CC +uses HOSTCC +uses OBJCOPY +uses CONFIG_CHIP_NAME +uses CONFIG_CONSOLE_VGA +uses CONFIG_PCI_ROM_RUN +uses HW_MEM_HOLE_SIZEK +uses HW_MEM_HOLE_SIZE_AUTO_INC +uses K8_HT_FREQ_1G_SUPPORT + +uses HT_CHAIN_UNITID_BASE +uses HT_CHAIN_END_UNITID_BASE +uses SB_HT_CHAIN_ON_BUS0 +uses SB_HT_CHAIN_UNITID_OFFSET_ONLY + +uses USE_DCACHE_RAM +uses DCACHE_RAM_BASE +uses DCACHE_RAM_SIZE +uses DCACHE_RAM_GLOBAL_VAR_SIZE +uses CONFIG_USE_INIT + +uses SERIAL_CPU_INIT + +uses ENABLE_APIC_EXT_ID +uses APIC_ID_OFFSET +uses LIFT_BSP_APIC_ID + +uses CONFIG_PCI_64BIT_PREF_MEM + +uses CONFIG_LB_MEM_TOPK + + +### +### Build options +### + +## +## ROM_SIZE is the size of boot ROM that this board will use. +## +default ROM_SIZE=524288 + +## +## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use +## +#default FALLBACK_SIZE=131072 +#256K +default FALLBACK_SIZE=0x40000 + +#more 1M for pgtbl +default CONFIG_LB_MEM_TOPK=2048 + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=1 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=1 +default IRQ_SLOT_COUNT=11 + +## +## Build code to export an x86 MP table +## Useful for specifying IRQ routing values +## +default HAVE_MP_TABLE=1 + +## ACPI tables will be included +#default HAVE_ACPI_TABLES=1 +## extra SSDT num +#default ACPI_SSDTX_NUM=1 + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=1 + +## +## Move the default LinuxBIOS cmos range off of AMD RTC registers +## +default LB_CKS_RANGE_START=49 +default LB_CKS_RANGE_END=122 +default LB_CKS_LOC=123 + +## +## Build code for SMP support +## Only worry about 2 micro processors +## +default CONFIG_SMP=1 +default CONFIG_MAX_CPUS=4 +default CONFIG_MAX_PHYSICAL_CPUS=2 +default CONFIG_LOGICAL_CPUS=1 + +default SERIAL_CPU_INIT=0 + +default ENABLE_APIC_EXT_ID=0 +default APIC_ID_OFFSET=0x8 +default LIFT_BSP_APIC_ID=1 + +#CHIP_NAME ? +default CONFIG_CHIP_NAME=1 + +#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead. +#2G +#default HW_MEM_HOLE_SIZEK=0x200000 +#1G +default HW_MEM_HOLE_SIZEK=0x100000 +#512M +#default HW_MEM_HOLE_SIZEK=0x80000 + +#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy +#default HW_MEM_HOLE_SIZE_AUTO_INC=1 + +#Opteron K8 1G HT Support +default K8_HT_FREQ_1G_SUPPORT=1 + +#VGA Console +default CONFIG_CONSOLE_VGA=1 +default CONFIG_PCI_ROM_RUN=1 + +#HT Unit ID offset, default is 1, the typical one +default HT_CHAIN_UNITID_BASE=0x06 + +#real SB Unit ID, default is 0x20, mean dont touch it at last +default HT_CHAIN_END_UNITID_BASE=0x01 + +#make the SB HT chain on bus 0, default is not (0) +default SB_HT_CHAIN_ON_BUS0=2 + +#only offset for SB chain?, default is yes(1) +#default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0 + +#allow capable device use that above 4G +#default CONFIG_PCI_64BIT_PREF_MEM=1 + +## +## enable CACHE_AS_RAM specifics +## +default USE_DCACHE_RAM=1 +default DCACHE_RAM_BASE=0xcc000 +default DCACHE_RAM_SIZE=0x04000 +default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000 +default CONFIG_USE_INIT=0 + +## +## Build code to setup a generic IOAPIC +## +default CONFIG_IOAPIC=1 + +## +## Clean up the motherboard id strings +## +default MAINBOARD_PART_NUMBER="MS9185" +default MAINBOARD_VENDOR="MSI" +default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1022 +default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2b80 + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 65536 + +## +## Use a small 8K stack +## +default STACK_SIZE=0x2000 + +## +## Use a small 32K heap +## +default HEAP_SIZE=0x8000 + +## +## Only use the option table in a normal image +## +default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE + +## +## LinuxBIOS C code runs at this location in RAM +## +default _RAMBASE=0x00100000 + +## +## Load the payload from the ROM +## +default CONFIG_ROM_STREAM = 1 + +### +### Defaults of options that you may want to override in the target config file +### + +## +## The default compiler +## +default CC="$(CROSS_COMPILE)gcc -m32" +default HOSTCC="gcc" + +## +## Disable the gdb stub by default +## +default CONFIG_GDB_STUB=0 + +## +## The Serial Console +## + +# To Enable the Serial Console +default CONFIG_CONSOLE_SERIAL8250=1 + +## Select the serial console baud rate +default TTYS0_BAUD=115200 +#default TTYS0_BAUD=57600 +#default TTYS0_BAUD=38400 +#default TTYS0_BAUD=19200 +#default TTYS0_BAUD=9600 +#default TTYS0_BAUD=4800 +#default TTYS0_BAUD=2400 +#default TTYS0_BAUD=1200 + +# Select the serial console base port +default TTYS0_BASE=0x3f8 + +# Select the serial protocol +# This defaults to 8 data bits, 1 stop bit, and no parity +default TTYS0_LCS=0x3 + +## +### Select the linuxBIOS loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +default DEFAULT_CONSOLE_LOGLEVEL=8 +## At a maximum only compile in this level of debugging +default MAXIMUM_CONSOLE_LOGLEVEL=8 + +## +## Select power on after power fail setting +default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" + +### End Options.lb +end diff --git a/src/mainboard/msi/ms9185/cache_as_ram_auto.c b/src/mainboard/msi/ms9185/cache_as_ram_auto.c new file mode 100644 index 0000000000..bb2212fb2e --- /dev/null +++ b/src/mainboard/msi/ms9185/cache_as_ram_auto.c @@ -0,0 +1,375 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2006 Tyan + * Copyright (C) 2006 AMD + * Written by Yinghai Lu <yinghailu@gmail.com> for Tyan and AMD. + * + * Copyright (C) 2006 MSI + * Written by bxshi <bingxunshi@gmail.com> for MSI. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#define ASSEMBLY 1 +#define __ROMCC__ + +#define RAMINIT_SYSINFO 1 +#define CACHE_AS_RAM_ADDRESS_DEBUG 0 + +#define SET_NB_CFG_54 1 + +//used by raminit +#define QRANK_DIMM_SUPPORT 1 + +//used by incoherent_ht +//#define K8_SCAN_PCI_BUS 1 +//#define K8_ALLOCATE_IO_RANGE 1 + + +//used by init_cpus and fidvid +#define K8_SET_FIDVID 1 +//if we want to wait for core1 done before DQS training, set it to 0 +#define K8_SET_FIDVID_CORE0_ONLY 1 + +#define DEBUG_SMBUS 1 + +#include <stdint.h> +#include <device/pci_def.h> +#include <device/pci_ids.h> +#include <arch/io.h> +#include <device/pnp_def.h> +#include <arch/romcc_io.h> +#include <cpu/x86/lapic.h> +#include "option_table.h" +#include "pc80/mc146818rtc_early.c" +#include "pc80/serial.c" +#include "arch/i386/lib/console.c" + +#if 0 +static void post_code(uint8_t value) { +#if 1 + int i; + for(i=0;i<0x80000;i++) { + outb(value, 0x80); + } +#endif +} +#endif + +#include <cpu/amd/model_fxx_rev.h> +#include "southbridge/broadcom/bcm5785/bcm5785_early_smbus.c" +#include "northbridge/amd/amdk8/raminit.h" +#include "cpu/amd/model_fxx/apic_timer.c" +#include "lib/delay.c" + +#if CONFIG_USE_INIT == 0 + #include "lib/memcpy.c" +#endif + + +#include "cpu/x86/lapic/boot_cpu.c" +#include "northbridge/amd/amdk8/reset_test.c" +#include "northbridge/amd/amdk8/debug.c" +#include "superio/nsc/pc87417/pc87417_early_serial.c" +#include "cpu/amd/mtrr/amd_earlymtrr.c" +#include "cpu/x86/bist.h" + +#include "northbridge/amd/amdk8/setup_resource_map.c" + +#define SERIAL_DEV PNP_DEV(0x2e, PC87417_SP1) +#define RTC_DEV PNP_DEV(0x2e, PC87417_RTC) +#include "southbridge/broadcom/bcm5785/bcm5785_early_setup.c" +static void memreset_setup(void) +{ +} + +static void memreset(int controllers, const struct mem_controller *ctrl) +{ +} + +static inline void activate_spd_rom(const struct mem_controller *ctrl) +{ +#define SMBUS_SWITCH1 0x70 +#define SMBUS_SWITCH2 0x72 + unsigned device = (ctrl->channel0[0]) >> 8; + smbus_send_byte(SMBUS_SWITCH1, device & 0x0f); + smbus_send_byte(SMBUS_SWITCH2, (device >> 4) & 0x0f ); +} + +#if 0 +static inline void change_i2c_mux(unsigned device) +{ +#define SMBUS_SWITCH1 0x70 +#define SMBUS_SWITCH2 0x72 + smbus_send_byte(SMBUS_SWITCH1, device & 0x0f); + smbus_send_byte(SMBUS_SWITCH2, (device >> 4) & 0x0f ); +} +#endif + + + +static inline int spd_read_byte(unsigned device, unsigned address) +{ + return smbus_read_byte(device, address); +} + +#include "northbridge/amd/amdk8/amdk8_f.h" +#include "northbridge/amd/amdk8/coherent_ht.c" + +#include "northbridge/amd/amdk8/incoherent_ht.c" + +#include "northbridge/amd/amdk8/raminit_f.c" + +#include "sdram/generic_sdram.c" + + /* msi does not want the default */ +#include "resourcemap.c" + +#include "cpu/amd/dualcore/dualcore.c" + +#define RC0 (0x10<<8) +#define RC1 (0x01<<8) + +#define DIMM0 0x50 +#define DIMM1 0x51 +#define DIMM2 0x52 +#define DIMM3 0x53 +#define DIMM4 0x54 +#define DIMM5 0x55 +#define DIMM6 0x56 +#define DIMM7 0x57 + + +#include "cpu/amd/car/copy_and_run.c" +#include "cpu/amd/car/post_cache_as_ram.c" + +#include "cpu/amd/model_fxx/init_cpus.c" + +#include "cpu/amd/model_fxx/fidvid.c" + +#if USE_FALLBACK_IMAGE == 1 + +#include "northbridge/amd/amdk8/early_ht.c" + +void failover_process(unsigned long bist, unsigned long cpu_init_detectedx) +{ + + /* Is this a cpu only reset? Is this a secondary cpu? */ + if ((cpu_init_detectedx) || (!boot_cpu())) { + if (last_boot_normal()) { // RTC already inited + goto normal_image; + } else { + goto fallback_image; + } + } + /* Nothing special needs to be done to find bus 0 */ + /* Allow the HT devices to be found */ + + enumerate_ht_chain(); + + bcm5785_enable_rom(); + + bcm5785_enable_lpc(); + + //enable RTC + pc87417_enable_dev(RTC_DEV); + + /* Is this a deliberate reset by the bios */ +// post_code(0x22); + if (bios_reset_detected() && last_boot_normal()) { + goto normal_image; + } + /* This is the primary cpu how should I boot? */ + else if (do_normal_boot()) { + goto normal_image; + } + else { + goto fallback_image; + } + normal_image: +// post_code(0x23); + __asm__ volatile ("jmp __normal_image" + : /* outputs */ + : "a" (bist), "b" (cpu_init_detectedx) /* inputs */ + ); + + fallback_image: +// post_code(0x25); + ; + +} +#endif + +void real_main(unsigned long bist, unsigned long cpu_init_detectedx); + +void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) +{ + +#if USE_FALLBACK_IMAGE == 1 + failover_process(bist, cpu_init_detectedx); +#endif + real_main(bist, cpu_init_detectedx); + +} + +void real_main(unsigned long bist, unsigned long cpu_init_detectedx) +{ + static const uint16_t spd_addr[] = { + //first node + RC0|DIMM0, RC0|DIMM2, RC0|DIMM4, RC0|DIMM6, + RC0|DIMM1, RC0|DIMM3, RC0|DIMM5, RC0|DIMM7, +#if CONFIG_MAX_PHYSICAL_CPUS > 1 + //second node + RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6, + RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7, +#endif + + }; + + struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); + + int needs_reset; + unsigned bsp_apicid = 0; + + if (bist == 0) { + bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); + } + +// post_code(0x32); + + pc87417_enable_serial(SERIAL_DEV, TTYS0_BASE); + uart_init(); + console_init(); + +// dump_mem(DCACHE_RAM_BASE+DCACHE_RAM_SIZE-0x200, DCACHE_RAM_BASE+DCACHE_RAM_SIZE); + + /* Halt if there was a built in self test failure */ + report_bist_failure(bist); + + print_debug("*sysinfo range: ["); print_debug_hex32(sysinfo); print_debug(","); print_debug_hex32((unsigned long)sysinfo+sizeof(struct sys_info)); print_debug(")\r\n"); + + setup_ms9185_resource_map(); +#if 0 + dump_pci_device(PCI_DEV(0, 0x18, 0)); + dump_pci_device(PCI_DEV(0, 0x19, 0)); +#endif + + print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\r\n"); + + setup_coherent_ht_domain(); + + wait_all_core0_started(); +#if CONFIG_LOGICAL_CPUS==1 + // It is said that we should start core1 after all core0 launched + /* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain, + * So here need to make sure last core0 is started, esp for two way system, + * (there may be apic id conflicts in that case) + */ + start_other_cores(); +//bx_a010- wait_all_other_cores_started(bsp_apicid); +#endif + + /* it will set up chains and store link pair for optimization later */ + ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn + + bcm5785_early_setup(); + + +#if 0 + //it your CPU min fid is 1G, you can change HT to 1G and FID to max one time. + needs_reset = optimize_link_coherent_ht(); + needs_reset |= optimize_link_incoherent_ht(sysinfo); +#endif + +#if K8_SET_FIDVID == 1 + + { + msr_t msr; + msr=rdmsr(0xc0010042); + print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\r\n"); + + } + + enable_fid_change(); + + enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn); + + init_fidvid_bsp(bsp_apicid); + + // show final fid and vid + { + msr_t msr; + msr=rdmsr(0xc0010042); + print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\r\n"); + + } +#endif + +#if 1 + needs_reset = optimize_link_coherent_ht(); + needs_reset |= optimize_link_incoherent_ht(sysinfo); + + // fidvid change will issue one LDTSTOP and the HT change will be effective too + if (needs_reset) { + print_info("ht reset -\r\n"); + soft_reset(); + } +#endif + allow_all_aps_stop(bsp_apicid); + + //It's the time to set ctrl in sysinfo now; + fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); + + enable_smbus(); + +#if 0 + int i; + for(i=0;i<2;i++) { + activate_spd_rom(sysinfo->ctrl+i); + dump_smbus_registers(); + } +#endif + +#if 0 + int i; + for(i=1;i<256;i<<=1) { + change_i2c_mux(i); + dump_smbus_registers(); + } +#endif + + memreset_setup(); + + //do we need apci timer, tsc...., only debug need it for better output + /* all ap stopped? */ +// init_timer(); // Need to use TMICT to synconize FID/VID + + sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo); + +#if 0 + print_pci_devices(); +#endif + +#if 0 +// dump_pci_devices(); + dump_pci_device_index_wait(PCI_DEV(0, 0x18, 2), 0x98); + dump_pci_device_index_wait(PCI_DEV(0, 0x19, 2), 0x98); +#endif + + post_cache_as_ram(); + + +} diff --git a/src/mainboard/msi/ms9185/chip.h b/src/mainboard/msi/ms9185/chip.h new file mode 100644 index 0000000000..6bd0a48912 --- /dev/null +++ b/src/mainboard/msi/ms9185/chip.h @@ -0,0 +1,28 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2006 MSI + * Written by bxshi <bingxunshi@gmail.com> for MSI. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +extern struct chip_operations mainboard_msi_ms9185_ops; + +struct mainboard_msi_ms9185_config { +// int fixup_scsi; +// int fixup_vga; +}; + diff --git a/src/mainboard/msi/ms9185/cmos.layout b/src/mainboard/msi/ms9185/cmos.layout new file mode 100644 index 0000000000..3f6d68f41c --- /dev/null +++ b/src/mainboard/msi/ms9185/cmos.layout @@ -0,0 +1,98 @@ +entries + +#start-bit length config config-ID name +#0 8 r 0 seconds +#8 8 r 0 alarm_seconds +#16 8 r 0 minutes +#24 8 r 0 alarm_minutes +#32 8 r 0 hours +#40 8 r 0 alarm_hours +#48 8 r 0 day_of_week +#56 8 r 0 day_of_month +#64 8 r 0 month +#72 8 r 0 year +#80 4 r 0 rate_select +#84 3 r 0 REF_Clock +#87 1 r 0 UIP +#88 1 r 0 auto_switch_DST +#89 1 r 0 24_hour_mode +#90 1 r 0 binary_values_enable +#91 1 r 0 square-wave_out_enable +#92 1 r 0 update_finished_enable +#93 1 r 0 alarm_interrupt_enable +#94 1 r 0 periodic_interrupt_enable +#95 1 r 0 disable_clock_updates +#96 288 r 0 temporary_filler +0 384 r 0 reserved_memory +384 1 e 4 boot_option +385 1 e 4 last_boot +386 1 e 1 ECC_memory +388 4 r 0 reboot_bits +392 3 e 5 baud_rate +395 1 e 1 hw_scrubber +396 1 e 1 interleave_chip_selects +397 2 e 8 max_mem_clock +399 1 e 2 dual_core +400 1 e 1 power_on_after_fail +412 4 e 6 debug_level +416 4 e 7 boot_first +420 4 e 7 boot_second +424 4 e 7 boot_third +428 4 h 0 boot_index +432 8 h 0 boot_countdown +440 4 e 9 slow_cpu +444 1 e 1 nmi +445 1 e 1 iommu +728 256 h 0 user_data +984 16 h 0 check_sum +# Reserve the extended AMD configuration registers +1000 24 r 0 reserved_memory + + + +enumerations + +#ID value text +1 0 Disable +1 1 Enable +2 0 Enable +2 1 Disable +4 0 Fallback +4 1 Normal +5 0 115200 +5 1 57600 +5 2 38400 +5 3 19200 +5 4 9600 +5 5 4800 +5 6 2400 +5 7 1200 +6 6 Notice +6 7 Info +6 8 Debug +6 9 Spew +7 0 Network +7 1 HDD +7 2 Floppy +7 8 Fallback_Network +7 9 Fallback_HDD +7 10 Fallback_Floppy +#7 3 ROM +8 0 400Mhz +8 1 333Mhz +8 2 266Mhz +8 3 200Mhz +9 0 off +9 1 87.5% +9 2 75.0% +9 3 62.5% +9 4 50.0% +9 5 37.5% +9 6 25.0% +9 7 12.5% + +checksums + +checksum 392 983 984 + + diff --git a/src/mainboard/msi/ms9185/get_bus_conf.c b/src/mainboard/msi/ms9185/get_bus_conf.c new file mode 100644 index 0000000000..1620bf870f --- /dev/null +++ b/src/mainboard/msi/ms9185/get_bus_conf.c @@ -0,0 +1,144 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2006 AMD + * Written by Yinghai Lu <yinghailu@gmail.com> for AMD. + * + * Copyright (C) 2006 MSI + * Written by bxshi <bingxunshi@gmail.com> for MSI. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ +#include <console/console.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include <string.h> +#include <stdint.h> +#if CONFIG_LOGICAL_CPUS==1 +#include <cpu/amd/dualcore.h> +#endif + +#include <cpu/amd/amdk8_sysconf.h> + +#include "mb_sysconf.h" + +// Global variables for MB layouts and these will be shared by irqtable mptable and acpi_tables +struct mb_sysconf_t mb_sysconf; + +static unsigned pci1234x[] = +{ //Here you only need to set value in pci1234 for HT-IO that could be installed or not + //You may need to preset pci1234 for HTIO board, please refer to src/northbridge/amd/amdk8/get_sblk_pci1234.c for detail + 0x0000ff0, + 0x0000ff0, +// 0x0000ff0, +// 0x0000ff0, +// 0x0000ff0, +// 0x0000ff0, +// 0x0000ff0, +// 0x0000ff0 +}; +static unsigned hcdnx[] = +{ //HT Chain device num, actually it is unit id base of every ht device in chain, assume every chain only have 4 ht device at most + 0x20202020, + 0x20202020, +// 0x20202020, +// 0x20202020, +// 0x20202020, +// 0x20202020, +// 0x20202020, +// 0x20202020, +}; + +extern void get_sblk_pci1234(void); + +static unsigned get_bus_conf_done = 0; + +void get_bus_conf(void) +{ + + unsigned apicid_base; + + device_t dev; + int i; + struct mb_sysconf_t *m; + + if(get_bus_conf_done==1) return; //do it only once + + get_bus_conf_done = 1; + + sysconf.mb = &mb_sysconf; + + m = sysconf.mb; + + sysconf.hc_possible_num = sizeof(pci1234x)/sizeof(pci1234x[0]); + + for(i=0;i<sysconf.hc_possible_num; i++) { + sysconf.pci1234[i] = pci1234x[i]; + sysconf.hcdn[i] = hcdnx[i]; + } + + get_sblk_pci1234(); + + sysconf.sbdn = (sysconf.hcdn[0] >> 8) & 0xff; + m->sbdn2 = sysconf.hcdn[0] & 0xff; // bcm5780 + + m->bus_bcm5785_0 = (sysconf.pci1234[0] >> 16) & 0xff; + m->bus_bcm5780[0] = m->bus_bcm5785_0; + + /* bcm5785 */ + dev = dev_find_slot(m->bus_bcm5785_0, PCI_DEVFN(sysconf.sbdn,0)); + if (dev) { + m->bus_bcm5785_1 = pci_read_config8(dev, PCI_SECONDARY_BUS); + dev = dev_find_slot(m->bus_bcm5785_1, PCI_DEVFN(0xd,0)); + if(dev) { + m->bus_bcm5785_1_1 = pci_read_config8(dev, PCI_SECONDARY_BUS); +#if HT_CHAIN_END_UNITID_BASE >= HT_CHAIN_UNITID_BASE + m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS); + m->bus_isa++; + printk_debug("bus_isa=%d\n",m->bus_isa); +#endif + } + } + else { + printk_debug("ERROR - could not find PCI %02x:%02x.0, using defaults\n", m->bus_bcm5785_0, sysconf.sbdn); + } + + /* bcm5780 */ + for(i = 1; i < 7; i++) { + dev = dev_find_slot(m->bus_bcm5780[0], PCI_DEVFN(m->sbdn2 + i - 1,0)); + if(dev) { + m->bus_bcm5780[i] = pci_read_config8(dev, PCI_SECONDARY_BUS); +#if HT_CHAIN_END_UNITID_BASE < HT_CHAIN_UNITID_BASE + m->bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS); + m->bus_isa++; + printk_debug("bus_isa=%d\n",m->bus_isa); +#endif + + } + else { + printk_debug("ERROR - could not find PCI %02x:%02x.0, using defaults\n", m->bus_bcm5780[0], m->sbdn2+i-1); + } + } + + +/*I/O APICs: APIC ID Version State Address*/ +#if CONFIG_LOGICAL_CPUS==1 + apicid_base = get_apicid_base(3); +#else + apicid_base = CONFIG_MAX_PHYSICAL_CPUS; +#endif + for(i=0;i<3;i++) + m->apicid_bcm5785[i] = apicid_base+i; +} diff --git a/src/mainboard/msi/ms9185/irq_tables.c b/src/mainboard/msi/ms9185/irq_tables.c new file mode 100644 index 0000000000..4769b03bac --- /dev/null +++ b/src/mainboard/msi/ms9185/irq_tables.c @@ -0,0 +1,126 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2006 AMD + * Written by Yinghai Lu <yinghailu@gmail.com> for AMD. + * + * Copyright (C) 2006 MSI + * Written by bxshi <bingxunshi@gmail.com> for MSI. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +/* This file was generated by getpir.c, do not modify! + (but if you do, please run checkpir on it to verify) + Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up + + Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM +*/ +#include <console/console.h> +#include <device/pci.h> +#include <string.h> +#include <stdint.h> +#include <arch/pirq_routing.h> +#include <cpu/amd/amdk8_sysconf.h> + +#include "mb_sysconf.h" + + +static void write_pirq_info(struct irq_info *pirq_info, uint8_t bus, uint8_t devfn, uint8_t link0, uint16_t bitmap0, + uint8_t link1, uint16_t bitmap1, uint8_t link2, uint16_t bitmap2,uint8_t link3, uint16_t bitmap3, + uint8_t slot, uint8_t rfu) +{ + pirq_info->bus = bus; + pirq_info->devfn = devfn; + + pirq_info->irq[0].link = link0; + pirq_info->irq[0].bitmap = bitmap0; + pirq_info->irq[1].link = link1; + pirq_info->irq[1].bitmap = bitmap1; + pirq_info->irq[2].link = link2; + pirq_info->irq[2].bitmap = bitmap2; + pirq_info->irq[3].link = link3; + pirq_info->irq[3].bitmap = bitmap3; + + pirq_info->slot = slot; + pirq_info->rfu = rfu; +} + +extern void get_bus_conf(void); + +unsigned long write_pirq_routing_table(unsigned long addr) +{ + + struct irq_routing_table *pirq; + struct irq_info *pirq_info; + unsigned slot_num; + uint8_t *v; + + uint8_t sum=0; + int i; + + struct mb_sysconf_t *m; + + get_bus_conf(); + + m = sysconf.mb; + + /* Align the table to be 16 byte aligned. */ + addr += 15; + addr &= ~15; + + /* This table must be betweeen 0xf0000 & 0x100000 */ + printk_info("Writing IRQ routing tables to 0x%x...", addr); + + pirq = (void *)(addr); + v = (uint8_t *)(addr); + + pirq->signature = PIRQ_SIGNATURE; + pirq->version = PIRQ_VERSION; + + pirq->rtr_bus = m->bus_bcm5785_0; + pirq->rtr_devfn = (sysconf.sbdn<<3)|0; + + pirq->exclusive_irqs = 0; + + pirq->rtr_vendor = 0x1166; + pirq->rtr_device = 0x0036; + + pirq->miniport_data = 0; + + memset(pirq->rfu, 0, sizeof(pirq->rfu)); + + pirq_info = (void *) ( &pirq->checksum + 1); + slot_num = 0; +//pci bridge + write_pirq_info(pirq_info, m->bus_bcm5785_0, (sysconf.sbdn<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0); + pirq_info++; slot_num++; + + pirq->size = 32 + 16 * slot_num; + + for (i = 0; i < pirq->size; i++) + sum += v[i]; + + sum = pirq->checksum - sum; + + if (sum != pirq->checksum) { + pirq->checksum = sum; + } + + printk_info("done.\n"); + + return (unsigned long) pirq_info; + +} diff --git a/src/mainboard/msi/ms9185/mainboard.c b/src/mainboard/msi/ms9185/mainboard.c new file mode 100644 index 0000000000..366f88e379 --- /dev/null +++ b/src/mainboard/msi/ms9185/mainboard.c @@ -0,0 +1,33 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2006 MSI + * Written by bxshi <bingxunshi@gmail.com> for MSI. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <device/device.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include <device/pci_ops.h> +#include "chip.h" + +#if CONFIG_CHIP_NAME == 1 +struct chip_operations mainboard_msi_ms9185_ops = { + CHIP_NAME("MSI MS-9185 mainboard") +}; +#endif diff --git a/src/mainboard/msi/ms9185/mb_sysconf.h b/src/mainboard/msi/ms9185/mb_sysconf.h new file mode 100644 index 0000000000..e52be15982 --- /dev/null +++ b/src/mainboard/msi/ms9185/mb_sysconf.h @@ -0,0 +1,40 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2006 AMD + * Written by Yinghai Lu <yinghailu@gmail.com> for AMD. + * + * Copyright (C) 2006 MSI + * Written by bxshi <bingxunshi@gmail.com> for MSI. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef MB_SYSCONF_H +#define MB_SYSCONF_H + +struct mb_sysconf_t { + unsigned char bus_isa; + unsigned char bus_bcm5780[7]; + unsigned char bus_bcm5785_0; + unsigned char bus_bcm5785_1; + unsigned char bus_bcm5785_1_1; + unsigned apicid_bcm5785[3]; + + unsigned sbdn2; +}; + +#endif + diff --git a/src/mainboard/msi/ms9185/mptable.c b/src/mainboard/msi/ms9185/mptable.c new file mode 100644 index 0000000000..4045745bcc --- /dev/null +++ b/src/mainboard/msi/ms9185/mptable.c @@ -0,0 +1,205 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2001 Eric W.Biederman<ebiderman@lnxi.com> + * + * Copyright (C) 2006 AMD + * Written by Yinghai Lu <yinghailu@gmail.com> for AMD. + * + * Copyright (C) 2006 MSI + * Written by bxshi <bingxunshi@gmail.com> for MSI. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <console/console.h> +#include <arch/smp/mpspec.h> +#include <arch/io.h> +#include <device/pci.h> +#include <string.h> +#include <stdint.h> +#if CONFIG_LOGICAL_CPUS==1 +#include <cpu/amd/dualcore.h> +#endif + +#include <cpu/amd/amdk8_sysconf.h> + +#include "mb_sysconf.h" + +extern void get_bus_conf(void); + +void *smp_write_config_table(void *v) +{ + static const char sig[4] = "PCMP"; + static const char oem[3] = "MSI"; + static const char productid[6] = "MS9185 "; + struct mp_config_table *mc; + + unsigned char bus_num; + int i; + struct mb_sysconf_t *m; + + mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN); + memset(mc, 0, sizeof(*mc)); + + memcpy(mc->mpc_signature, sig, sizeof(sig)); + mc->mpc_length = sizeof(*mc); /* initially just the header */ + mc->mpc_spec = 0x04; + mc->mpc_checksum = 0; /* not yet computed */ + memcpy(mc->mpc_oem, oem, sizeof(oem)); + memcpy(mc->mpc_productid, productid, sizeof(productid)); + mc->mpc_oemptr = 0; + mc->mpc_oemsize = 0; + mc->mpc_entry_count = 0; /* No entries yet... */ + mc->mpc_lapic = LAPIC_ADDR; + mc->mpe_length = 0; + mc->mpe_checksum = 0; + mc->reserved = 0; + + smp_write_processors(mc); + + get_bus_conf(); + m = sysconf.mb; + +/*Bus: Bus ID Type*/ + /* define bus and isa numbers */ + for(bus_num = 0; bus_num < m->bus_isa; bus_num++) { + smp_write_bus(mc, bus_num, "PCI "); + } + smp_write_bus(mc, m->bus_isa, "ISA "); + +/*I/O APICs: APIC ID Version State Address*/ + { + device_t dev = 0; + int i; + struct resource *res; + for(i=0; i<3; i++) { + dev = dev_find_device(0x1166, 0x0235, dev); + if (dev) { + res = find_resource(dev, PCI_BASE_ADDRESS_0); + if (res) { + smp_write_ioapic(mc, m->apicid_bcm5785[i], 0x11, res->base); + } + } + } + + } + +/*I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# */ + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, m->apicid_bcm5785[0], 0x0); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x1, m->apicid_bcm5785[0], 0x1); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, m->apicid_bcm5785[0], 0x2); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x3, m->apicid_bcm5785[0], 0x3); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x4, m->apicid_bcm5785[0], 0x4); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x5, m->apicid_bcm5785[0], 0x5); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x6, m->apicid_bcm5785[0], 0x6); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x7, m->apicid_bcm5785[0], 0x7); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x8, m->apicid_bcm5785[0], 0x8); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x9, m->apicid_bcm5785[0], 0x9); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0xc, m->apicid_bcm5785[0], 0xc); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0xd, m->apicid_bcm5785[0], 0xd); + +//IDE + outb(0x02, 0xc00); outb(0x0e, 0xc01); + + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_bcm5785_0, ((1+sysconf.sbdn)<<2)|1, m->apicid_bcm5785[0], 0xe); // IDE + +//SATA + outb(0x07, 0xc00); outb(0x0f, 0xc01); + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_1, (0x0e<<2)|0, m->apicid_bcm5785[0], 0xf); + +//USB + outb(0x01, 0xc00); outb(0x0a, 0xc01); + for(i=0;i<3;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_0, ((2+sysconf.sbdn)<<2)|i, m->apicid_bcm5785[0], 0xa); // + } + + + + /* enable int */ + /* why here? must get the BAR and PCI command bit 1 set before enable it ....*/ + { + device_t dev; + dev = dev_find_device(0x1166, 0x0205, 0); + if(dev) { + uint32_t dword; + dword = pci_read_config32(dev, 0x6c); + dword |= (1<<4); // enable interrupts + pci_write_config32(dev, 0x6c, dword); + } + } + +//First pci-x slot (on bcm5785) under bus_bcm5785_1:d.0 + // AIC 8130 Galileo Technology... + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_1_1, (6<<2)|i, m->apicid_bcm5785[1], 2 + (1+i)%4); // + } + + +//pci slot (on bcm5785) + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_0, (5<<2)|i, m->apicid_bcm5785[1], 8+i%4); // + } + + +//onboard ati + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5785_0, (4<<2)|0, m->apicid_bcm5785[1], 0x1); + +//PCI-X on bcm5780 + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[1], (4<<2)|i, m->apicid_bcm5785[1], 2 + (0+i)%4); // + } + +//onboard Broadcom + for(i=0;i<2;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[2], (4<<2)|i, m->apicid_bcm5785[1], 0xa + (0+i)%4); // + } + + +// First PCI-E x8 + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[5], (0<<2)|i, m->apicid_bcm5785[1], 0xe); // + } + + +// Second PCI-E x8 + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[3], (0<<2)|i, m->apicid_bcm5785[1], 0xc); // + } + +// Third PCI-E x1 + for(i=0;i<4;i++) { + smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_bcm5780[4], (0<<2)|i, m->apicid_bcm5785[1], 0xd); // + } + +/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/ + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, MP_APIC_ALL, 0x0); + smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, MP_APIC_ALL, 0x1); + /* There is no extension information... */ + + /* Compute the checksums */ + mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length); + mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length); + printk_debug("Wrote the mp table end at: %p - %p\n", + mc, smp_next_mpe_entry(mc)); + return smp_next_mpe_entry(mc); +} + +unsigned long write_smp_table(unsigned long addr) +{ + void *v; + v = smp_write_floating_table(addr); + return (unsigned long)smp_write_config_table(v); +} diff --git a/src/mainboard/msi/ms9185/resourcemap.c b/src/mainboard/msi/ms9185/resourcemap.c new file mode 100644 index 0000000000..a093e748d8 --- /dev/null +++ b/src/mainboard/msi/ms9185/resourcemap.c @@ -0,0 +1,291 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2003 Stefan Reinauer <stepan@coresystems.de> + * + * Copyright (C) 2006 AMD + * Written by Yinghai Lu <yinghailu@gmail.com> for AMD. + * + * Copyright (C) 2006 MSI + * Written by bxshi <bingxunshi@gmail.com> for MSI. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +/* + * ms9185 needs a different resource map + * + */ + +static void setup_ms9185_resource_map(void) +{ + static const unsigned int register_values[] = { + /* Careful set limit registers before base registers which contain the enables */ + /* DRAM Limit i Registers + * F1:0x44 i = 0 + * F1:0x4C i = 1 + * F1:0x54 i = 2 + * F1:0x5C i = 3 + * F1:0x64 i = 4 + * F1:0x6C i = 5 + * F1:0x74 i = 6 + * F1:0x7C i = 7 + * [ 2: 0] Destination Node ID + * 000 = Node 0 + * 001 = Node 1 + * 010 = Node 2 + * 011 = Node 3 + * 100 = Node 4 + * 101 = Node 5 + * 110 = Node 6 + * 111 = Node 7 + * [ 7: 3] Reserved + * [10: 8] Interleave select + * specifies the values of A[14:12] to use with interleave enable. + * [15:11] Reserved + * [31:16] DRAM Limit Address i Bits 39-24 + * This field defines the upper address bits of a 40 bit address + * that define the end of the DRAM region. + */ + PCI_ADDR(0, 0x18, 1, 0x44), 0x0000f8f8, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x4C), 0x0000f8f8, 0x00000001, + PCI_ADDR(0, 0x18, 1, 0x54), 0x0000f8f8, 0x00000002, + PCI_ADDR(0, 0x18, 1, 0x5C), 0x0000f8f8, 0x00000003, + PCI_ADDR(0, 0x18, 1, 0x64), 0x0000f8f8, 0x00000004, + PCI_ADDR(0, 0x18, 1, 0x6C), 0x0000f8f8, 0x00000005, + PCI_ADDR(0, 0x18, 1, 0x74), 0x0000f8f8, 0x00000006, + PCI_ADDR(0, 0x18, 1, 0x7C), 0x0000f8f8, 0x00000007, + /* DRAM Base i Registers + * F1:0x40 i = 0 + * F1:0x48 i = 1 + * F1:0x50 i = 2 + * F1:0x58 i = 3 + * F1:0x60 i = 4 + * F1:0x68 i = 5 + * F1:0x70 i = 6 + * F1:0x78 i = 7 + * [ 0: 0] Read Enable + * 0 = Reads Disabled + * 1 = Reads Enabled + * [ 1: 1] Write Enable + * 0 = Writes Disabled + * 1 = Writes Enabled + * [ 7: 2] Reserved + * [10: 8] Interleave Enable + * 000 = No interleave + * 001 = Interleave on A[12] (2 nodes) + * 010 = reserved + * 011 = Interleave on A[12] and A[14] (4 nodes) + * 100 = reserved + * 101 = reserved + * 110 = reserved + * 111 = Interleve on A[12] and A[13] and A[14] (8 nodes) + * [15:11] Reserved + * [13:16] DRAM Base Address i Bits 39-24 + * This field defines the upper address bits of a 40-bit address + * that define the start of the DRAM region. + */ + PCI_ADDR(0, 0x18, 1, 0x40), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x48), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x50), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x58), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x60), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x68), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x70), 0x0000f8fc, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x78), 0x0000f8fc, 0x00000000, + + /* Memory-Mapped I/O Limit i Registers + * F1:0x84 i = 0 + * F1:0x8C i = 1 + * F1:0x94 i = 2 + * F1:0x9C i = 3 + * F1:0xA4 i = 4 + * F1:0xAC i = 5 + * F1:0xB4 i = 6 + * F1:0xBC i = 7 + * [ 2: 0] Destination Node ID + * 000 = Node 0 + * 001 = Node 1 + * 010 = Node 2 + * 011 = Node 3 + * 100 = Node 4 + * 101 = Node 5 + * 110 = Node 6 + * 111 = Node 7 + * [ 3: 3] Reserved + * [ 5: 4] Destination Link ID + * 00 = Link 0 + * 01 = Link 1 + * 10 = Link 2 + * 11 = Reserved + * [ 6: 6] Reserved + * [ 7: 7] Non-Posted + * 0 = CPU writes may be posted + * 1 = CPU writes must be non-posted + * [31: 8] Memory-Mapped I/O Limit Address i (39-16) + * This field defines the upp adddress bits of a 40-bit address that + * defines the end of a memory-mapped I/O region n + */ + PCI_ADDR(0, 0x18, 1, 0x84), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x8C), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x94), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x9C), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xA4), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xAC), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xB4), 0x00000048, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xBC), 0x00000048, 0x00ffff20, + + /* Memory-Mapped I/O Base i Registers + * F1:0x80 i = 0 + * F1:0x88 i = 1 + * F1:0x90 i = 2 + * F1:0x98 i = 3 + * F1:0xA0 i = 4 + * F1:0xA8 i = 5 + * F1:0xB0 i = 6 + * F1:0xB8 i = 7 + * [ 0: 0] Read Enable + * 0 = Reads disabled + * 1 = Reads Enabled + * [ 1: 1] Write Enable + * 0 = Writes disabled + * 1 = Writes Enabled + * [ 2: 2] Cpu Disable + * 0 = Cpu can use this I/O range + * 1 = Cpu requests do not use this I/O range + * [ 3: 3] Lock + * 0 = base/limit registers i are read/write + * 1 = base/limit registers i are read-only + * [ 7: 4] Reserved + * [31: 8] Memory-Mapped I/O Base Address i (39-16) + * This field defines the upper address bits of a 40bit address + * that defines the start of memory-mapped I/O region i + */ + PCI_ADDR(0, 0x18, 1, 0x80), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x88), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x90), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0x98), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xA0), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xA8), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xB0), 0x000000f0, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xB8), 0x000000f0, 0x00fc0003, + + /* PCI I/O Limit i Registers + * F1:0xC4 i = 0 + * F1:0xCC i = 1 + * F1:0xD4 i = 2 + * F1:0xDC i = 3 + * [ 2: 0] Destination Node ID + * 000 = Node 0 + * 001 = Node 1 + * 010 = Node 2 + * 011 = Node 3 + * 100 = Node 4 + * 101 = Node 5 + * 110 = Node 6 + * 111 = Node 7 + * [ 3: 3] Reserved + * [ 5: 4] Destination Link ID + * 00 = Link 0 + * 01 = Link 1 + * 10 = Link 2 + * 11 = reserved + * [11: 6] Reserved + * [24:12] PCI I/O Limit Address i + * This field defines the end of PCI I/O region n + * [31:25] Reserved + */ + PCI_ADDR(0, 0x18, 1, 0xC4), 0xFE000FC8, 0x01fff020, + PCI_ADDR(0, 0x18, 1, 0xCC), 0xFE000FC8, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xD4), 0xFE000FC8, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xDC), 0xFE000FC8, 0x00000000, + + /* PCI I/O Base i Registers + * F1:0xC0 i = 0 + * F1:0xC8 i = 1 + * F1:0xD0 i = 2 + * F1:0xD8 i = 3 + * [ 0: 0] Read Enable + * 0 = Reads Disabled + * 1 = Reads Enabled + * [ 1: 1] Write Enable + * 0 = Writes Disabled + * 1 = Writes Enabled + * [ 3: 2] Reserved + * [ 4: 4] VGA Enable + * 0 = VGA matches Disabled + * 1 = matches all address < 64K and where A[9:0] is in the + * range 3B0-3BB or 3C0-3DF independen of the base & limit registers + * [ 5: 5] ISA Enable + * 0 = ISA matches Disabled + * 1 = Blocks address < 64K and in the last 768 bytes of eack 1K block + * from matching agains this base/limit pair + * [11: 6] Reserved + * [24:12] PCI I/O Base i + * This field defines the start of PCI I/O region n + * [31:25] Reserved + */ + PCI_ADDR(0, 0x18, 1, 0xC0), 0xFE000FCC, 0x00000003, + PCI_ADDR(0, 0x18, 1, 0xC8), 0xFE000FCC, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xD0), 0xFE000FCC, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xD8), 0xFE000FCC, 0x00000000, + + /* Config Base and Limit i Registers + * F1:0xE0 i = 0 + * F1:0xE4 i = 1 + * F1:0xE8 i = 2 + * F1:0xEC i = 3 + * [ 0: 0] Read Enable + * 0 = Reads Disabled + * 1 = Reads Enabled + * [ 1: 1] Write Enable + * 0 = Writes Disabled + * 1 = Writes Enabled + * [ 2: 2] Device Number Compare Enable + * 0 = The ranges are based on bus number + * 1 = The ranges are ranges of devices on bus 0 + * [ 3: 3] Reserved + * [ 6: 4] Destination Node + * 000 = Node 0 + * 001 = Node 1 + * 010 = Node 2 + * 011 = Node 3 + * 100 = Node 4 + * 101 = Node 5 + * 110 = Node 6 + * 111 = Node 7 + * [ 7: 7] Reserved + * [ 9: 8] Destination Link + * 00 = Link 0 + * 01 = Link 1 + * 10 = Link 2 + * 11 - Reserved + * [15:10] Reserved + * [23:16] Bus Number Base i + * This field defines the lowest bus number in configuration region i + * [31:24] Bus Number Limit i + * This field defines the highest bus number in configuration regin i + */ + PCI_ADDR(0, 0x18, 1, 0xE0), 0x0000FC88, 0xff000203, + PCI_ADDR(0, 0x18, 1, 0xE4), 0x0000FC88, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xE8), 0x0000FC88, 0x00000000, + PCI_ADDR(0, 0x18, 1, 0xEC), 0x0000FC88, 0x00000000, + }; + + int max; + max = sizeof(register_values)/sizeof(register_values[0]); + setup_resource_map(register_values, max); +} + diff --git a/src/southbridge/broadcom/bcm5785/bcm5785_sata.c b/src/southbridge/broadcom/bcm5785/bcm5785_sata.c index 470bc47c73..426ee0ff0b 100644 --- a/src/southbridge/broadcom/bcm5785/bcm5785_sata.c +++ b/src/southbridge/broadcom/bcm5785/bcm5785_sata.c @@ -21,6 +21,8 @@ static void sata_init(struct device *dev) uint8_t *base; uint8_t *mmio; struct resource *res; + unsigned int mmio_base; + volatile unsigned int *mmio_reg; int i; if(!(dev->path.u.pci.devfn & 7)) { // only set it in Func0 @@ -30,6 +32,21 @@ static void sata_init(struct device *dev) res = find_resource(dev, 0x24); base = res->base; + + mmio_base = base; + mmio_base &= 0xfffffffc; + mmio_reg = (unsigned int *)( mmio_base + 0x10f0 ); + * mmio_reg = 0x40000001; + mmio_reg = ( unsigned int *)( mmio_base + 0x8c ); + * mmio_reg = 0x00ff2007; + mdelay( 10 ); + * mmio_reg = 0x78592009; + mdelay( 10 ); + * mmio_reg = 0x00082004; + mdelay( 10 ); + * mmio_reg = 0x00002004; + mdelay( 10 ); + //init PHY printk_debug("init PHY...\n"); diff --git a/targets/msi/ms9185/Config.lb b/targets/msi/ms9185/Config.lb new file mode 100644 index 0000000000..ef1c8d7113 --- /dev/null +++ b/targets/msi/ms9185/Config.lb @@ -0,0 +1,94 @@ +## +## This file is part of the LinuxBIOS project. +## +## Copyright (C) 2006 MSI +## Written by bxshi <bingxunshi@gmail.com> for MSI. +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; either version 2 of the License, or +## (at your option) any later version. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +# Sample config file for +# the msi ms9185 +# This will make a target directory of ./ms9185 + +target ms9185 +mainboard msi/ms9185 + +# ms9185 +romimage "normal" +# 36k for ATI option rom + option ROM_SIZE = 512*1024-36*1024 +# option ROM_SIZE = 524288 +# option ROM_SIZE = 425984 +# 64K for Etherboot +# option ROM_SIZE = 458752 + option USE_FALLBACK_IMAGE=0 +# option ROM_IMAGE_SIZE=0x13800 +# option ROM_IMAGE_SIZE=0x18800 + option ROM_IMAGE_SIZE=0x20000 +# option ROM_IMAGE_SIZE=0x15800 + option XIP_ROM_SIZE=0x40000 + option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal" +# payload ../../../payloads/tg3--ide_disk.zelf +# payload ../../../payloads/filo.elf +# payload ../../../payloads/filo_mem.elf +# payload ../../../payloads/filo.zelf +# payload ../../../payloads/tg3--filo_hda2.zelf +# payload ../../../payloads/tg3.zelf +# payload ../../../../payloads/tg3_vga.zelf +# payload ../../../../payloads/tg3--filo_hda2_vga.zelf +# payload /filo.elf + payload /tg3--filo.elf +# payload ../../../../payloads/e1000_vga.zelf +# payload ../../../../payloads/tg3--filo_hda2_vga_5_4.zelf +# payload ../../../payloads/tg3_com2.zelf +# payload ../../../payloads/e1000--filo.zelf +# payload ../../../payloads/tg3--e1000--filo.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_5.3.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf +end + +romimage "fallback" + option USE_FALLBACK_IMAGE=1 +# option ROM_IMAGE_SIZE=0x13800 +# option ROM_IMAGE_SIZE=0x19800 + option ROM_IMAGE_SIZE=0x20000 +# option ROM_IMAGE_SIZE=0x15800 + option XIP_ROM_SIZE=0x40000 + option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback" +# payload ../../../payloads/tg3--ide_disk.zelf +# payload ../../../payloads/filo.elf +# payload ../../../payloads/filo_mem.elf +# payload ../../../payloads/filo.zelf +# payload ../../../payloads/tg3--filo_hda2.zelf +# payload ../../../payloads/tg3.zelf +# payload ../../../../payloads/tg3_vga.zelf +# payload ../../../../payloads/memtest +# payload ../../../../payloads/e1000_vga.zelf +# payload ../../../../payloads/filo_hda.zelf +# payload ../../../../payloads/tg3--filo_hda2_vga.zelf +# payload /filo.elf + payload /tg3--filo.elf +# payload ../../../../payloads/tg3--filo_hda2_vga_5_4.zelf +# payload ../../../payloads/tg3_com2.zelf +# payload ../../../payloads/e1000--filo.zelf +# payload ../../../payloads/tg3--e1000--filo.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_5.3.zelf +# payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf +end + +buildrom ./ms9185.lxb ROM_SIZE "normal" "fallback" |