summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--Documentation/flash_tutorial/ext_power.md28
-rw-r--r--Documentation/flash_tutorial/ext_standalone.md23
-rw-r--r--Documentation/flash_tutorial/flash_ic_diode.svg61
-rw-r--r--Documentation/flash_tutorial/flash_ic_no_diode.svg55
-rw-r--r--Documentation/flash_tutorial/index.md105
-rw-r--r--Documentation/flash_tutorial/int_flashrom.md19
-rw-r--r--Documentation/flash_tutorial/no_ext_power.md22
-rw-r--r--Documentation/index.md1
-rw-r--r--Documentation/mainboard/index.md14
-rw-r--r--Documentation/mainboard/lenovo/flashlayout_xx20.svg52
-rw-r--r--Documentation/mainboard/lenovo/flashlayout_xx30.svg61
-rw-r--r--Documentation/mainboard/lenovo/t420.md16
-rw-r--r--Documentation/mainboard/lenovo/t430.md15
-rw-r--r--Documentation/mainboard/lenovo/t4xx_series.md20
-rw-r--r--Documentation/mainboard/lenovo/xx20_series.md48
-rw-r--r--Documentation/mainboard/lenovo/xx30_series.md76
16 files changed, 616 insertions, 0 deletions
diff --git a/Documentation/flash_tutorial/ext_power.md b/Documentation/flash_tutorial/ext_power.md
new file mode 100644
index 0000000000..542ccfd934
--- /dev/null
+++ b/Documentation/flash_tutorial/ext_power.md
@@ -0,0 +1,28 @@
+# Flashing firmware externally supplying direct power
+
+**WARNING:** Never use a high current rated power supply, like PC ATX power
+ supply. It'll literally melt your PCB traces on short circuit.
+
+On some mainboards the flash IC Vcc pin is connected to a diode, which prevents
+powering the rest of the board.
+
+![][flash_ic_diode]
+
+Please have a look at the mainboard specific documentation for details.
+
+On those boards it's safe to use a programmer and supply power externally.
+
+**WARNING:** Verify that you apply the correct voltage!
+
+## USB programmer
+USB programmers are usually current limited by the host USB hub. On USB 2.0
+ports the limit is 500mA, which is sufficient to power the flash. Those are
+the best choice as they are stateless and have a fast power on reset cycle.
+
+## Single board computers (like BeagleBone Black / RPi)
+Be careful when connecting a flash chip, especially when using a Pomona
+test-clip. A short circuit or overcurrent (250mA) causes a brown-out reset,
+resulting in a reboot of the running operating system (and possible loss of
+remote shell).
+
+[flash_ic_diode]: flash_ic_diode.svg
diff --git a/Documentation/flash_tutorial/ext_standalone.md b/Documentation/flash_tutorial/ext_standalone.md
new file mode 100644
index 0000000000..3a676ce47c
--- /dev/null
+++ b/Documentation/flash_tutorial/ext_standalone.md
@@ -0,0 +1,23 @@
+# Flashing firmware standalone
+
+If none of the other methods work, there are three possibilities:
+
+## Desolder
+You must remove or desolder the flash IC before you can flash it.
+It's recommended to solder a socket in place of the flash IC.
+
+When flashing the IC, always connect all input pins.
+If in doubt, pull /WP, /HOLD, /RESET and alike up towards Vcc.
+
+## SPI flash emulator
+If you are a developer, you might want to use an [EM100Pro] instead, which sets
+the onboard flash on hold, and allows to run custom firmware.
+It provides a very fast development cycle without actually writing to flash.
+
+## SPI flash overwrite
+It is possible to set the onboard flash on hold and use another flash chip.
+Connect all lines one-to-one, except /HOLD. Pull /HOLD of the soldered flash IC
+low, and /HOLD of your replacement flash IC high.
+
+
+[EM100Pro]: https://www.dediprog.com/product/EM100Pro
diff --git a/Documentation/flash_tutorial/flash_ic_diode.svg b/Documentation/flash_tutorial/flash_ic_diode.svg
new file mode 100644
index 0000000000..22cd87277f
--- /dev/null
+++ b/Documentation/flash_tutorial/flash_ic_diode.svg
@@ -0,0 +1,61 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no"?>
+<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.0//EN" "http://www.w3.org/TR/2001/PR-SVG-20010719/DTD/svg10.dtd">
+<svg width="4cm" height="3cm" viewBox="311 435 68 45" xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink">
+ <g>
+ <g>
+ <rect style="fill: #ffffff" x="322.125" y="451.034" width="37.75" height="26.6444"/>
+ <rect style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x="322.125" y="451.034" width="37.75" height="26.6444"/>
+ <text font-size="4.51549" style="fill: #000000;text-anchor:middle;font-family:sans-serif;font-style:normal;font-weight:normal" x="341" y="465.734">
+ <tspan x="341" y="465.734"></tspan>
+ </text>
+ </g>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="359.875" y1="456.784" x2="368.527" y2="456.784"/>
+ <text font-size="4.51549" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="348.75" y="457.909">
+ <tspan x="348.75" y="457.909">VCC</tspan>
+ </text>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="359.763" y1="461.772" x2="368.652" y2="461.784"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="360.138" y1="466.872" x2="368.527" y2="466.909"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="360.277" y1="471.534" x2="368.402" y2="471.534"/>
+ <text font-size="4.51549" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="345.752" y="463.247">
+ <tspan x="345.752" y="463.247">HOLD</tspan>
+ </text>
+ <line style="fill: none; fill-opacity:0; stroke-width: 0.2; stroke: #000000" x1="346.652" y1="459.159" x2="358.402" y2="459.159"/>
+ <text font-size="4.51549" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="349.752" y="468.247">
+ <tspan x="349.752" y="468.247">CLK</tspan>
+ </text>
+ <text font-size="4.51549" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="353.502" y="472.997">
+ <tspan x="353.502" y="472.997">DI</tspan>
+ </text>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="313.49" y1="456.922" x2="322.143" y2="456.922"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="313.378" y1="461.909" x2="322.268" y2="461.922"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="313.753" y1="467.009" x2="322.143" y2="467.047"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="313.893" y1="471.672" x2="322.018" y2="471.672"/>
+ <text font-size="4.51549" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="323.752" y="458.372">
+ <tspan x="323.752" y="458.372">CS</tspan>
+ </text>
+ <text font-size="4.51549" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="324.127" y="468.497">
+ <tspan x="324.127" y="468.497">WP</tspan>
+ </text>
+ <text font-size="4.51549" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="323.752" y="472.997">
+ <tspan x="323.752" y="472.997">GND</tspan>
+ </text>
+ <text font-size="4.51549" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="324.127" y="463.497">
+ <tspan x="324.127" y="463.497">DO</tspan>
+ </text>
+ <line style="fill: none; fill-opacity:0; stroke-width: 0.2; stroke: #000000" x1="330.852" y1="454.397" x2="323.902" y2="454.409"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 0.2; stroke: #000000" x1="330.802" y1="464.397" x2="323.852" y2="464.409"/>
+ </g>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="368.252" y1="456.797" x2="373.902" y2="456.784"/>
+ <g>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="374.027" y1="456.784" x2="374.027" y2="438.895"/>
+ <polyline style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" points="375.027,439.777 374.027,437.777 373.027,439.777 "/>
+ </g>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="314.277" y1="471.784" x2="314.277" y2="479.659"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="317.027" y1="479.659" x2="311.502" y2="479.672"/>
+ <g>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1.2; stroke: #000000" x1="374.027" y1="443.284" x2="374.027" y2="447.434"/>
+ <polygon style="fill: #000000" points="372.027,447.434 374.027,451.434 376.027,447.434 "/>
+ <polygon style="fill: none; fill-opacity:0; stroke-width: 1.2; stroke: #000000" points="372.027,447.434 374.027,451.434 376.027,447.434 "/>
+ </g>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1.2; stroke: #000000" x1="370.402" y1="452.032" x2="377.527" y2="452.032"/>
+</svg>
diff --git a/Documentation/flash_tutorial/flash_ic_no_diode.svg b/Documentation/flash_tutorial/flash_ic_no_diode.svg
new file mode 100644
index 0000000000..543c9262df
--- /dev/null
+++ b/Documentation/flash_tutorial/flash_ic_no_diode.svg
@@ -0,0 +1,55 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no"?>
+<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.0//EN" "http://www.w3.org/TR/2001/PR-SVG-20010719/DTD/svg10.dtd">
+<svg width="4cm" height="3cm" viewBox="311 435 65 45" xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink">
+ <g>
+ <g>
+ <rect style="fill: #ffffff" x="322.124" y="451.034" width="37.75" height="26.6444"/>
+ <rect style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x="322.124" y="451.034" width="37.75" height="26.6444"/>
+ <text font-size="4.51556" style="fill: #000000;text-anchor:middle;font-family:sans-serif;font-style:normal;font-weight:normal" x="340.999" y="465.734">
+ <tspan x="340.999" y="465.734"></tspan>
+ </text>
+ </g>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="359.874" y1="456.784" x2="368.528" y2="456.784"/>
+ <text font-size="4.51556" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="348.75" y="457.91">
+ <tspan x="348.75" y="457.91">VCC</tspan>
+ </text>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="359.762" y1="461.772" x2="368.652" y2="461.784"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="360.138" y1="466.872" x2="368.528" y2="466.91"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="360.278" y1="471.534" x2="368.402" y2="471.534"/>
+ <text font-size="4.51556" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="345.752" y="463.246">
+ <tspan x="345.752" y="463.246">HOLD</tspan>
+ </text>
+ <line style="fill: none; fill-opacity:0; stroke-width: 0.2; stroke: #000000" x1="346.652" y1="459.16" x2="358.402" y2="459.16"/>
+ <text font-size="4.51556" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="349.752" y="468.246">
+ <tspan x="349.752" y="468.246">CLK</tspan>
+ </text>
+ <text font-size="4.51556" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="353.502" y="472.996">
+ <tspan x="353.502" y="472.996">DI</tspan>
+ </text>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="313.49" y1="456.922" x2="322.142" y2="456.922"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="313.378" y1="461.91" x2="322.268" y2="461.922"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="313.752" y1="467.01" x2="322.142" y2="467.046"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="313.892" y1="471.672" x2="322.018" y2="471.672"/>
+ <text font-size="4.51556" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="323.752" y="458.372">
+ <tspan x="323.752" y="458.372">CS</tspan>
+ </text>
+ <text font-size="4.51556" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="324.128" y="468.496">
+ <tspan x="324.128" y="468.496">WP</tspan>
+ </text>
+ <text font-size="4.51556" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="323.752" y="472.996">
+ <tspan x="323.752" y="472.996">GND</tspan>
+ </text>
+ <text font-size="4.51556" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="324.128" y="463.496">
+ <tspan x="324.128" y="463.496">DO</tspan>
+ </text>
+ <line style="fill: none; fill-opacity:0; stroke-width: 0.2; stroke: #000000" x1="330.852" y1="454.396" x2="323.902" y2="454.41"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 0.2; stroke: #000000" x1="330.802" y1="464.396" x2="323.852" y2="464.41"/>
+ </g>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="368.252" y1="456.796" x2="373.902" y2="456.784"/>
+ <g>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="374.028" y1="456.784" x2="374.028" y2="438.896"/>
+ <polyline style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" points="375.028,439.778 374.028,437.778 373.028,439.778 "/>
+ </g>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="314.278" y1="471.784" x2="314.278" y2="479.66"/>
+ <line style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" x1="317.028" y1="479.66" x2="311.502" y2="479.672"/>
+</svg>
diff --git a/Documentation/flash_tutorial/index.md b/Documentation/flash_tutorial/index.md
new file mode 100644
index 0000000000..1a291372a6
--- /dev/null
+++ b/Documentation/flash_tutorial/index.md
@@ -0,0 +1,105 @@
+# Flashing firmware tutorial
+
+Updating the firmware is possible using the **internal method**, where the updates
+happen from a running system, or using the **external method**, where the system
+is in a shut down state and an external programmer is attached to write into the
+flash IC.
+
+## Contents
+
+* [Flashing internaly](int_flashrom.md)
+* [Flashing firmware standalone](ext_standalone.md)
+* [Flashing firmware externally supplying direct power](ext_power.md)
+* [Flashing firmware externally without supplying direct power](no_ext_power.md)
+
+## General advice
+
+* It's recommended to only flash the BIOS region.
+* Always verify the firmware image.
+* If you flash externally and have transmission errors:
+ * Use short wires
+ * Reduce clock frequency
+ * Check power supply
+ * Make sure that there are no other bus masters (EC, ME, SoC, ...)
+
+## Internal method
+
+This method using [flashrom] is available on many platforms, as long as they
+aren't locked down.
+
+There are various protection schemes that make it impossible to modify or
+replace a firmware from a running system. coreboot allows to disable these
+mechanisms, making it possible to overwrite (or update) the firmware from a
+running system.
+
+Usually you must use the **external method** once to install a retrofitted
+coreboot and then you can use the **internal method** for future updates.
+
+There are multiple ways to update the firmware:
+* Using flashrom's *internal* programmer to directly write into the firmware
+ flash IC, running on the target machine itself
+* A proprietary software to update the firmware, running on the target machine
+ itself
+* A UEFI firmware update capsule
+
+More details on flashrom's
+* [internal programmer](int_flashrom.md)
+
+## External method
+
+External flashing is possible on many platforms, but requires disassembling
+the target hardware. You need to buy a flash programmer, that
+exposes the same interface as your flash IC (likely SPI).
+
+Please also have a look at the mainboard-specific documentation for details.
+
+After exposing the firmware flash IC, read the schematics and use one of the
+possible methods:
+
+* [Flashing firmware standalone](ext_standalone.md)
+* [Flashing firmware externally supplying direct power](ext_power.md)
+* [Flashing firmware externally without supplying direct power](no_ext_power.md)
+
+**WARNING:** Using the wrong method or accidentally using the wrong pinout might
+ permanently damage your hardware!
+
+## Using a layout file
+On platforms where the flash IC is shared with other components you might want
+to write only a part of the flash IC. On Intel for example there are IFD, ME and
+GBE which don't need to be updated to install coreboot.
+To make [flashrom] only write the *bios* region, leaving Intel ME and Intel IFD
+untouched, you can use a layout file, which can be created using ifdtool
+
+```bash
+ifdtool -f rom.layout coreboot.rom
+```
+
+and looks similar to:
+
+```
+00000000:00000fff fd
+00500000:00bfffff bios
+00003000:004fffff me
+00001000:00002fff gbe
+```
+
+By specifying *-l* and *-i* [flashrom] writes a single region:
+```bash
+flashrom -l rom.layout -i bios -w coreboot.rom -p <programmer>
+```
+
+## Using an IFD to determine the layout
+flashrom version 1.0 supports reading the layout from the IFD (first 4KiB of
+the ROM). You don't need to manually specify a layout it, but it only works
+under the following conditions:
+
+* Only available on Intel ICH7+
+* There's only one flash IC when flashing externally
+
+```bash
+flashrom --ifd -i bios -w coreboot.rom -p <programmer>
+```
+
+**TODO** explain FMAP regions, normal/fallback mechanism, flash lock mechanisms
+
+[flashrom]: https://www.flashrom.org/Flashrom
diff --git a/Documentation/flash_tutorial/int_flashrom.md b/Documentation/flash_tutorial/int_flashrom.md
new file mode 100644
index 0000000000..28b534b003
--- /dev/null
+++ b/Documentation/flash_tutorial/int_flashrom.md
@@ -0,0 +1,19 @@
+# Flashing firmware internally
+
+**WARNING:** If you flash a broken firmware and have no recovery mechanism, you
+ must use the **external method** to flash a working firmware again.
+
+## Using flashrom
+This method does only work on Linux, if it isn't locked down.
+You may also need to boot with 'iomem=relaxed' in the kernel command
+line if CONFIG_IO_STRICT_DEVMEM is set.
+
+
+For more details please also check [flashrom's wiki].
+Use the programmer *internal* to flash *coreboot.rom* internally:
+
+```bash
+flashrom -p internal -w coreboot.rom
+```
+
+[flashrom's wiki]: https://www.flashrom.org/Flashrom
diff --git a/Documentation/flash_tutorial/no_ext_power.md b/Documentation/flash_tutorial/no_ext_power.md
new file mode 100644
index 0000000000..b97ba4cc7a
--- /dev/null
+++ b/Documentation/flash_tutorial/no_ext_power.md
@@ -0,0 +1,22 @@
+# Flashing firmware externally supplying no power
+
+On some mainboards the flash IC's Vcc pin is connected to the internal
+power-rail, powering the entire board if the flash IC is powered externally.
+Likely it powers other chips which access the flash IC, preventing the external
+programmer from reading/writing the chip. It also violates the components'
+power sequence, bringing the ICs into an undefined state.
+
+![][flash_ic_no_diode]
+
+Please have a look at the mainboard specific documentation for details.
+
+On those boards it's recommended to use a programmer without supplying power
+externally.
+
+The key to read and write the flash IC is to put the machine into *S3* sleep-
+state or *S5* sleep-state *maybe* with Wake-On-LAN enabled.
+Another option that sometimes works is to keep the device in reset. This method requires
+knowledge of the board schematics and might require hardware modifications.
+Use a multimeter to make sure the flash IC is powered in those sleep states.
+
+[flash_ic_no_diode]: flash_ic_no_diode.svg
diff --git a/Documentation/index.md b/Documentation/index.md
index b20eedc10f..e69f2ea7d5 100644
--- a/Documentation/index.md
+++ b/Documentation/index.md
@@ -23,3 +23,4 @@ Contents:
* [Vendorcode-specific documentation](vendorcode/index.md)
* [Utilities](util.md)
* [Release notes for past releases](releases/index.md)
+* [Flashing firmware tutorial](flash_tutorial/index.md)
diff --git a/Documentation/mainboard/index.md b/Documentation/mainboard/index.md
index 45eb217e4d..c346a3b8f0 100644
--- a/Documentation/mainboard/index.md
+++ b/Documentation/mainboard/index.md
@@ -26,6 +26,20 @@ This section contains documentation about coreboot on specific mainboards.
- [Compaq 8200 Elite SFF](hp/compaq_8200_sff.md)
+## Lenovo
+
+- [T4xx common](lenovo/t4xx_series.md)
+
+### Sandy Bridge series
+
+- [T420](lenovo/t420.md)
+- [T420 / T520 / X220 / T420s / W520 common](lenovo/xx20_series.md)
+
+### Ivy Bridge series
+
+- [T430](lenovo/t430.md)
+- [T430 / T530 / X230 / W530 common](lenovo/xx30_series.md)
+
## SiFive
- [SiFive HiFive Unleashed](sifive/hifive-unleashed.md)
diff --git a/Documentation/mainboard/lenovo/flashlayout_xx20.svg b/Documentation/mainboard/lenovo/flashlayout_xx20.svg
new file mode 100644
index 0000000000..8884ac37ad
--- /dev/null
+++ b/Documentation/mainboard/lenovo/flashlayout_xx20.svg
@@ -0,0 +1,52 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no"?>
+<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.0//EN" "http://www.w3.org/TR/2001/PR-SVG-20010719/DTD/svg10.dtd">
+<svg width="10cm" height="8cm" viewBox="265 -156 186 159" xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink">
+ <g>
+ <rect style="fill: #ffffff" x="307.888" y="-152.131" width="49.1438" height="30.4667"/>
+ <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="307.888" y="-152.131" width="49.1438" height="30.4667"/>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:middle;font-family:sans-serif;font-style:normal;font-weight:normal" x="332.46" y="-134.831">
+ <tspan x="332.46" y="-134.831">IFD</tspan>
+ </text>
+ </g>
+ <g>
+ <rect style="fill: #ffffff" x="308" y="-91.1844" width="49.1438" height="59.7756"/>
+ <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="308" y="-91.1844" width="49.1438" height="59.7756"/>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:middle;font-family:sans-serif;font-style:normal;font-weight:normal" x="332.572" y="-59.2299">
+ <tspan x="332.572" y="-59.2299">ME</tspan>
+ </text>
+ </g>
+ <g>
+ <rect style="fill: #ffffff" x="307.934" y="-31.6442" width="49.1438" height="30.8828"/>
+ <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="307.934" y="-31.6442" width="49.1438" height="30.8828"/>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:middle;font-family:sans-serif;font-style:normal;font-weight:normal" x="332.506" y="-14.1361">
+ <tspan x="332.506" y="-14.1361">BIOS</tspan>
+ </text>
+ </g>
+ <g>
+ <rect style="fill: #ffffff" x="308" y="-121.59" width="49.1438" height="30.4667"/>
+ <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="308" y="-121.59" width="49.1438" height="30.4667"/>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:middle;font-family:sans-serif;font-style:normal;font-weight:normal" x="332.572" y="-104.29">
+ <tspan x="332.572" y="-104.29">GBE</tspan>
+ </text>
+ </g>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="265.968" y="-149.208">
+ <tspan x="265.968" y="-149.208">0x000000</tspan>
+ </text>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="266.362" y="-120.102">
+ <tspan x="266.362" y="-120.102">0x001000</tspan>
+ </text>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="266.162" y="-88.8972">
+ <tspan x="266.162" y="-88.8972">0x003000</tspan>
+ </text>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="266.144" y="-29.6656">
+ <tspan x="266.144" y="-29.6656">0x500000</tspan>
+ </text>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="266.326" y="1.87412">
+ <tspan x="266.326" y="1.87412">0x800000</tspan>
+ </text>
+ <path style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" d="M 380.877 -151.013 C 401.876,-151.013 379.377,-73.513 400.627,-72.513"/>
+ <path style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" d="M 381.377 -0.763268 C 395.238,-0.763268 387.016,-72.763 400.877,-72.763"/>
+ <text font-size="10.1598" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="406.127" y="-68.513">
+ <tspan x="406.127" y="-68.513">Flash #0</tspan>
+ </text>
+</svg>
diff --git a/Documentation/mainboard/lenovo/flashlayout_xx30.svg b/Documentation/mainboard/lenovo/flashlayout_xx30.svg
new file mode 100644
index 0000000000..5cc4e4fbaf
--- /dev/null
+++ b/Documentation/mainboard/lenovo/flashlayout_xx30.svg
@@ -0,0 +1,61 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no"?>
+<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.0//EN" "http://www.w3.org/TR/2001/PR-SVG-20010719/DTD/svg10.dtd">
+<svg width="10cm" height="11cm" viewBox="265 -156 187 213" xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink">
+ <g>
+ <rect style="fill: #ffffff" x="307.888" y="-152.131" width="49.1438" height="30.4667"/>
+ <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="307.888" y="-152.131" width="49.1438" height="30.4667"/>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:middle;font-family:sans-serif;font-style:normal;font-weight:normal" x="332.46" y="-134.831">
+ <tspan x="332.46" y="-134.831">IFD</tspan>
+ </text>
+ </g>
+ <g>
+ <rect style="fill: #ffffff" x="308" y="-91.1844" width="49.1438" height="59.7756"/>
+ <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="308" y="-91.1844" width="49.1438" height="59.7756"/>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:middle;font-family:sans-serif;font-style:normal;font-weight:normal" x="332.572" y="-59.2299">
+ <tspan x="332.572" y="-59.2299">ME</tspan>
+ </text>
+ </g>
+ <g>
+ <rect style="fill: #ffffff" x="307.934" y="-31.6442" width="49.1438" height="85.7161"/>
+ <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="307.934" y="-31.6442" width="49.1438" height="85.7161"/>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:middle;font-family:sans-serif;font-style:normal;font-weight:normal" x="332.506" y="13.2805">
+ <tspan x="332.506" y="13.2805">BIOS</tspan>
+ </text>
+ </g>
+ <g>
+ <rect style="fill: #ffffff" x="308" y="-121.59" width="49.1438" height="30.4667"/>
+ <rect style="fill: none; fill-opacity:0; stroke-width: 2; stroke: #000000" x="308" y="-121.59" width="49.1438" height="30.4667"/>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:middle;font-family:sans-serif;font-style:normal;font-weight:normal" x="332.572" y="-104.29">
+ <tspan x="332.572" y="-104.29">GBE</tspan>
+ </text>
+ </g>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="265.968" y="-149.208">
+ <tspan x="265.968" y="-149.208">0x000000</tspan>
+ </text>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="266.362" y="-120.102">
+ <tspan x="266.362" y="-120.102">0x001000</tspan>
+ </text>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="266.162" y="-88.8972">
+ <tspan x="266.162" y="-88.8972">0x003000</tspan>
+ </text>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="266.144" y="-29.6656">
+ <tspan x="266.144" y="-29.6656">0x500000</tspan>
+ </text>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="266.326" y="1.87412">
+ <tspan x="266.326" y="1.87412">0x800000</tspan>
+ </text>
+ <path style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" d="M 380.877 -151.013 C 401.876,-151.013 379.377,-73.513 400.627,-72.513"/>
+ <path style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" d="M 381.377 -0.763268 C 395.238,-0.763268 387.016,-72.763 400.877,-72.763"/>
+ <text font-size="10.1598" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="406.127" y="-68.513">
+ <tspan x="406.127" y="-68.513">Flash #0</tspan>
+ </text>
+ <path style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" d="M 381.223 -0.537117 C 402.222,-0.537117 379.285,28.8102 399.872,27.8376"/>
+ <path style="fill: none; fill-opacity:0; stroke-width: 1; stroke: #000000" d="M 382.176 54.9128 C 396.037,54.9128 385.445,27.9997 399.548,27.8376"/>
+ <text font-size="10.1598" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="407.157" y="30.2529">
+ <tspan x="407.157" y="30.2529">Flash #1</tspan>
+ </text>
+ <text font-size="6.77333" style="fill: #000000;text-anchor:start;font-family:sans-serif;font-style:normal;font-weight:normal" x="266.591" y="54.9733">
+ <tspan x="266.591" y="54.9733">0xc00000</tspan>
+ </text>
+ <line style="fill: none; fill-opacity:0; stroke-width: 2; stroke-dasharray: 4; stroke: #000000" x1="305.271" y1="-1.2113" x2="378.831" y2="-1.17038"/>
+</svg>
diff --git a/Documentation/mainboard/lenovo/t420.md b/Documentation/mainboard/lenovo/t420.md
new file mode 100644
index 0000000000..ff7a0a9238
--- /dev/null
+++ b/Documentation/mainboard/lenovo/t420.md
@@ -0,0 +1,16 @@
+# Lenovo T420
+
+## Flashing instructions
+You have to disassemble the whole device, as the flash IC is on the bottom
+of the mainboard.
+
+For more details have a look at [T420 / T520 / X220 / T420s / W520 common] and
+
+```eval_rst
+:doc:`../../flash_tutorial/ext_power`
+```
+
+Steps to access the flash IC are described here [T4xx series].
+
+[T4xx series]: t4xx_series.md
+[T420 / T520 / X220 / T420s / W520 common]: xx20_series.md
diff --git a/Documentation/mainboard/lenovo/t430.md b/Documentation/mainboard/lenovo/t430.md
new file mode 100644
index 0000000000..787246f4d4
--- /dev/null
+++ b/Documentation/mainboard/lenovo/t430.md
@@ -0,0 +1,15 @@
+# Lenovo T430
+
+## Flashing instructions
+You have to disassemble the whole device, as the flash ICs are on the bottom
+of the mainboard.
+
+For more details have a look at [T430 / T530 / X230 / T430s / W530 common] and
+```eval_rst
+:doc:`../../flash_tutorial/ext_power`
+```
+
+Steps to access the flash IC are described here [T4xx series].
+
+[T4xx series]: t4xx_series.md
+[T430 / T530 / X230 / T430s / W530 common]: xx30_series.md
diff --git a/Documentation/mainboard/lenovo/t4xx_series.md b/Documentation/mainboard/lenovo/t4xx_series.md
new file mode 100644
index 0000000000..23fe0fbe53
--- /dev/null
+++ b/Documentation/mainboard/lenovo/t4xx_series.md
@@ -0,0 +1,20 @@
+# Lenovo T4xx series disassembly instructions
+
+A skilled engineer takes around 40 minutes to disassemble, flash and reassemble
+the whole device.
+
+# Steps to access the flash IC:
+
+* Unplug the main battery
+* Remove the harddisk, CDROM, ExpressCard, SIM-card, SDcard, SmartCard, ...
+* Open the bottom flap and remove the keyboard screw
+* Remove the keyboard
+* Remove the screen
+* Remove the top enclosure
+* Remove the CMOS battery
+* Remove the speakers
+* Remove WWAN and WIFI card
+* Remove the CPU fan
+* Unplug the power cable
+* Remove the bottom enclosure
+* Flip the mainboard and remove the main frame
diff --git a/Documentation/mainboard/lenovo/xx20_series.md b/Documentation/mainboard/lenovo/xx20_series.md
new file mode 100644
index 0000000000..976a29ba9f
--- /dev/null
+++ b/Documentation/mainboard/lenovo/xx20_series.md
@@ -0,0 +1,48 @@
+# Lenovo Sandy Bridge series
+
+## Flashing coreboot
+```eval_rst
++---------------------+--------------------+
+| Type | Value |
++=====================+====================+
+| Socketed flash | no |
++---------------------+--------------------+
+| Size | 8 MiB |
++---------------------+--------------------+
+| In circuit flashing | Yes |
++---------------------+--------------------+
+| Package | SOIC-8 |
++---------------------+--------------------+
+| Write protection | No |
++---------------------+--------------------+
+| Dual BIOS feature | No |
++---------------------+--------------------+
+| Internal flashing | Yes |
++---------------------+--------------------+
+```
+
+## Installation instructions
+* Update the EC firmware, as there's no support for EC updates in coreboot.
+* Do **NOT** accidently swap pins or power on the board while a SPI flasher
+ is connected. It will destroy your device.
+* It's recommended to only flash the BIOS region. In that case you don't
+ need to extract BLOBs from vendor firmware.
+ If you want to flash the whole chip, you need BLOBs when building
+ coreboot.
+* The shipped *Flash layout* allocates 3MiB to the BIOS region, which is the space
+ usable by coreboot.
+* ROM chip size should be set to 8MiB.
+
+```eval_rst
+Please also have a look at :doc:`../../flash_tutorial/index`.
+```
+
+## Flash layout
+There's one 8MiB flash which contains IFD, GBE, ME and BIOS regions.
+On Lenovo's UEFI the EC firmware update is placed at the start of the BIOS
+region. The update is then written into the EC once.
+
+![][fl]
+
+[fl]: flashlayout_xx20.svg
+
diff --git a/Documentation/mainboard/lenovo/xx30_series.md b/Documentation/mainboard/lenovo/xx30_series.md
new file mode 100644
index 0000000000..e65a3f2a6f
--- /dev/null
+++ b/Documentation/mainboard/lenovo/xx30_series.md
@@ -0,0 +1,76 @@
+# Lenovo Ivy Bridge series
+
+## Flashing coreboot
+```eval_rst
++---------------------+--------------------------------+
+| Type | Value |
++=====================+================================+
+| Socketed flash | no |
++---------------------+--------------------------------+
+| Size | 8 MiB + 4MiB |
++---------------------+--------------------------------+
+| In circuit flashing | Yes |
++---------------------+--------------------------------+
+| Package | SOIC-8 |
++---------------------+--------------------------------+
+| Write protection | No |
++---------------------+--------------------------------+
+| Dual BIOS feature | No |
++---------------------+--------------------------------+
+| Internal flashing | Yes |
++---------------------+--------------------------------+
+```
+
+## Installation instructions
+* Update the EC firmware, as there's no support for EC updates in coreboot.
+* Do **NOT** accidently swap pins or power on the board while a SPI flasher
+ is connected. It will permanently brick your device.
+* It's recommended to only flash the BIOS region. In that case you don't
+ need to extract BLOBs from vendor firmware.
+ If you want to flash the whole chip, you need BLOBs when building
+ coreboot.
+* The *Flash layout* shows that by default 7MiB of space are available for
+ the use with coreboot.
+* In that case you only want to use a part of the BIOS region that must not
+ exceed 4MiB in size, which means CONFIG_CBFS_SIZE must be smaller than 4MiB.
+* ROM chip size should be set to 12MiB.
+
+```eval_rst
+Please also have a look at :doc:`../../flash_tutorial/index`.
+```
+
+## Splitting the coreboot.rom
+
+To split the coreboot.rom into two images (one for the 8MiB and one for the
+4 MiB flash IC), run the following commands:
+
+```bash
+dd of=top.rom bs=1M if=build/coreboot.rom skip=8
+dd of=bottom.rom bs=1M if=build/coreboot.rom count=8
+```
+
+That gives one ROM for each flash IC, where *top.rom* is the upper part of the
+flash image, that resides on the 4 MiB flash and *bottom.rom* is the lower part
+of the flash image, that resides on the 8 MiB flash.
+
+## Dumping a full ROM
+
+If you flash externally you need to read both flash chips to get two images
+(one for the 8MiB and one for the 4 MiB flash IC), and then run the following
+command to concatenate the files:
+
+```bash
+cat bottom.rom top.rom > firmware.rom
+```
+
+## Flash layout
+There's one 8MiB and one 4 MiB flash which contains IFD, GBE, ME and
+BIOS region. These two flash ICs appear as a single 12MiB when flashing
+internally.
+On Lenovo's UEFI the EC firmware update is placed at the start of the BIOS
+region. The update is then written into the EC once.
+
+![][fl]
+
+[fl]: flashlayout_xx30.svg
+