summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--src/mainboard/google/trogdor/board.h5
-rw-r--r--src/mainboard/google/trogdor/mainboard.c63
-rw-r--r--src/soc/qualcomm/sc7180/Kconfig4
-rw-r--r--src/soc/qualcomm/sc7180/Makefile.inc1
-rw-r--r--src/soc/qualcomm/sc7180/display/mdss.c191
5 files changed, 262 insertions, 2 deletions
diff --git a/src/mainboard/google/trogdor/board.h b/src/mainboard/google/trogdor/board.h
index bd7222fefa..39661b5f21 100644
--- a/src/mainboard/google/trogdor/board.h
+++ b/src/mainboard/google/trogdor/board.h
@@ -13,6 +13,11 @@
#define GPIO_SD_CD_L GPIO(69)
#define GPIO_AMP_ENABLE GPIO(23)
+/* Display specific GPIOS */
+#define GPIO_BACKLIGHT_ENABLE GPIO(12)
+#define GPIO_EDP_BRIDGE_ENABLE (CONFIG(TROGDOR_REV0) ? GPIO(14) : GPIO(104))
+#define GPIO_EN_PP3300_DX_EDP (CONFIG(TROGDOR_REV0) ? GPIO(106) : GPIO(30))
+
void setup_chromeos_gpios(void);
#endif /* _COREBOOT_SRC_MAINBOARD_GOOGLE_TROGDOR_BOARD_H_ */
diff --git a/src/mainboard/google/trogdor/mainboard.c b/src/mainboard/google/trogdor/mainboard.c
index 349c3064c3..57f3a3ba0f 100644
--- a/src/mainboard/google/trogdor/mainboard.c
+++ b/src/mainboard/google/trogdor/mainboard.c
@@ -1,9 +1,21 @@
/* SPDX-License-Identifier: GPL-2.0-only */
+#include <bootmode.h>
+#include <delay.h>
#include <device/device.h>
+#include <device/i2c_simple.h>
+#include <drivers/ti/sn65dsi86bridge/sn65dsi86bridge.h>
+#include <soc/display/mipi_dsi.h>
+#include <soc/display/mdssreg.h>
#include <soc/qupv3_config.h>
+#include <soc/qupv3_i2c.h>
#include <soc/usb.h>
+#include "board.h"
+
+#define BRIDGE_BUS 0x2
+#define BRIDGE_CHIP 0x2d
+
static struct usb_board_data usb0_board_data = {
.pll_bias_control_2 = 0x22,
.imp_ctrl1 = 0x08,
@@ -20,7 +32,6 @@ static void setup_usb(void)
static void qi2s_configure_gpios(void)
{
-
gpio_configure(GPIO(49), GPIO49_FUNC_MI2S_1_SCK,
GPIO_NO_PULL, GPIO_8MA, GPIO_OUTPUT);
@@ -34,7 +45,6 @@ static void qi2s_configure_gpios(void)
static void load_qup_fw(void)
{
qupv3_se_fw_load_and_init(QUPV3_0_SE1, SE_PROTOCOL_SPI, MIXED); /* ESIM SPI */
- qupv3_se_fw_load_and_init(QUPV3_0_SE2, SE_PROTOCOL_I2C, MIXED); /* EDP Bridge I2C */
qupv3_se_fw_load_and_init(QUPV3_0_SE3, SE_PROTOCOL_UART, FIFO); /* BT UART */
qupv3_se_fw_load_and_init(QUPV3_0_SE4, SE_PROTOCOL_I2C, MIXED); /* Pen Detect I2C */
qupv3_se_fw_load_and_init(QUPV3_0_SE5, SE_PROTOCOL_I2C, MIXED); /* SAR I2C */
@@ -51,11 +61,60 @@ static void load_qup_fw(void)
qupv3_se_fw_load_and_init(QUPV3_1_SE5, SE_PROTOCOL_I2C, MIXED); /* Codec I2C */
}
+static void configure_display(void)
+{
+ printk(BIOS_INFO, "%s: Bridge gpio init\n", __func__);
+
+ /* Bridge Enable GPIO */
+ gpio_output(GPIO_EDP_BRIDGE_ENABLE, 1);
+
+ /* PP3300 EDP power supply */
+ gpio_output(GPIO_EN_PP3300_DX_EDP, 1);
+}
+
+static void display_init(struct edid *edid)
+{
+ uint32_t dsi_bpp = 24;
+ uint32_t lanes = 4;
+
+ if (mdss_dsi_config(edid, lanes, dsi_bpp))
+ return;
+
+ sn65dsi86_bridge_configure(BRIDGE_BUS, BRIDGE_CHIP, edid, lanes, dsi_bpp);
+ mdp_dsi_video_config(edid);
+ mdss_dsi_video_mode_config(edid, dsi_bpp);
+ mdp_dsi_video_on();
+}
+
+static void display_startup(void)
+{
+ static struct edid ed;
+ enum dp_pll_clk_src ref_clk = SN65_SEL_19MHZ;
+
+ i2c_init(QUPV3_0_SE2, I2C_SPEED_FAST); /* EDP Bridge I2C */
+ if (display_init_required()) {
+ configure_display();
+ mdelay(250); /* Delay for the panel to be up */
+ sn65dsi86_bridge_init(BRIDGE_BUS, BRIDGE_CHIP, ref_clk);
+ if (sn65dsi86_bridge_read_edid(BRIDGE_BUS, BRIDGE_CHIP, &ed) < 0)
+ return;
+
+ printk(BIOS_INFO, "display init!\n");
+
+ /* Configure backlight */
+ gpio_output(GPIO_BACKLIGHT_ENABLE, 1);
+ display_init(&ed);
+ set_vbe_mode_info_valid(&ed, (uintptr_t)0);
+ } else
+ printk(BIOS_INFO, "Skipping display init.\n");
+}
+
static void mainboard_init(struct device *dev)
{
setup_usb();
qi2s_configure_gpios();
load_qup_fw();
+ display_startup();
}
static void mainboard_enable(struct device *dev)
diff --git a/src/soc/qualcomm/sc7180/Kconfig b/src/soc/qualcomm/sc7180/Kconfig
index 17df0d036f..d543ef5134 100644
--- a/src/soc/qualcomm/sc7180/Kconfig
+++ b/src/soc/qualcomm/sc7180/Kconfig
@@ -13,6 +13,10 @@ config SOC_QUALCOMM_SC7180
select ARM64_USE_ARCH_TIMER
select SOC_QUALCOMM_COMMON
select HAVE_UART_SPECIAL
+ select BOOTBLOCK_CONSOLE
+ select MAINBOARD_HAS_NATIVE_VGA_INIT
+ select MAINBOARD_FORCE_NATIVE_VGA_INIT
+ select HAVE_LINEAR_FRAMEBUFFER
if SOC_QUALCOMM_SC7180
diff --git a/src/soc/qualcomm/sc7180/Makefile.inc b/src/soc/qualcomm/sc7180/Makefile.inc
index ec6ab6c162..eea38d9766 100644
--- a/src/soc/qualcomm/sc7180/Makefile.inc
+++ b/src/soc/qualcomm/sc7180/Makefile.inc
@@ -62,6 +62,7 @@ ramstage-$(CONFIG_DRIVERS_UART) += qupv3_uart.c
ramstage-$(CONFIG_MAINBOARD_DO_NATIVE_VGA_INIT) += display/dsi_phy_pll.c
ramstage-$(CONFIG_MAINBOARD_DO_NATIVE_VGA_INIT) += display/dsi_phy.c
ramstage-$(CONFIG_MAINBOARD_DO_NATIVE_VGA_INIT) += display/dsi.c
+ramstage-$(CONFIG_MAINBOARD_DO_NATIVE_VGA_INIT) += display/mdss.c
################################################################################
diff --git a/src/soc/qualcomm/sc7180/display/mdss.c b/src/soc/qualcomm/sc7180/display/mdss.c
new file mode 100644
index 0000000000..2d6bf6fcd3
--- /dev/null
+++ b/src/soc/qualcomm/sc7180/display/mdss.c
@@ -0,0 +1,191 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#include <device/mmio.h>
+#include <console/console.h>
+#include <delay.h>
+#include <edid.h>
+#include <soc/display/mdssreg.h>
+
+#define MDSS_MDP_MAX_PREFILL_FETCH 25
+
+static void mdss_source_pipe_config(struct edid *edid)
+{
+ uint32_t img_size, out_size, stride;
+ uint32_t fb_off = 0;
+ uint32_t flip_bits = 0;
+ uint32_t src_xy = 0;
+ uint32_t dst_xy = 0;
+
+ /* write active region size*/
+ img_size = (edid->mode.va << 16) | edid->mode.ha;
+ out_size = img_size;
+ stride = (edid->mode.ha * edid->framebuffer_bits_per_pixel/8);
+
+ if (!fb_off) { /* left */
+ dst_xy = (edid->mode.vborder << 16) | edid->mode.hborder;
+ src_xy = dst_xy;
+ } else { /* right */
+ dst_xy = (edid->mode.vborder << 16);
+ src_xy = (edid->mode.vborder << 16) | fb_off;
+ }
+
+ printk(BIOS_INFO, "%s: src=%x fb_off=%x src_xy=%x dst_xy=%x\n",
+ __func__, out_size, fb_off, src_xy, dst_xy);
+
+ write32(&mdp_sspp->sspp_src_ystride0, stride);
+ write32(&mdp_sspp->sspp_src_size, out_size);
+ write32(&mdp_sspp->sspp_out_size, out_size);
+ write32(&mdp_sspp->sspp_src_xy, src_xy);
+ write32(&mdp_sspp->sspp_out_xy, dst_xy);
+
+ /* Tight Packing 4bpp Alpha 8-bit A R B G */
+ write32(&mdp_sspp->sspp_src_format, 0x000236ff);
+ write32(&mdp_sspp->sspp_src_unpack_pattern, 0x03020001);
+
+ flip_bits |= BIT(31);
+ write32(&mdp_sspp->sspp_sw_pic_ext_c0_req_pixels, out_size);
+ write32(&mdp_sspp->sspp_sw_pic_ext_c1c2_req_pixels, out_size);
+ write32(&mdp_sspp->sspp_sw_pic_ext_c3_req_pixels, out_size);
+ write32(&mdp_sspp->sspp_src_op_mode, flip_bits);
+}
+
+static void mdss_vbif_setup(void)
+{
+ write32(&vbif_rt->vbif_out_axi_amemtype_conf0, 0x33333333);
+ write32(&vbif_rt->vbif_out_axi_amemtype_conf1, 0x00333333);
+}
+
+static void mdss_intf_tg_setup(struct edid *edid)
+{
+ uint32_t hsync_period, vsync_period;
+ uint32_t hsync_start_x, hsync_end_x;
+ uint32_t display_hctl, hsync_ctl, display_vstart, display_vend;
+
+ hsync_period = edid->mode.ha + edid->mode.hbl;
+ vsync_period = edid->mode.va + edid->mode.vbl;
+ hsync_start_x = edid->mode.hbl - edid->mode.hso;
+ hsync_end_x = hsync_period - edid->mode.hso - 1;
+ display_vstart = (edid->mode.vbl - edid->mode.vso) * hsync_period;
+ display_vend = ((vsync_period - edid->mode.vso) * hsync_period) - 1;
+ hsync_ctl = (hsync_period << 16) | edid->mode.hspw;
+ display_hctl = (hsync_end_x << 16) | hsync_start_x;
+
+ write32(&mdp_intf->intf_hsync_ctl, hsync_ctl);
+ write32(&mdp_intf->intf_vysnc_period_f0,
+ vsync_period * hsync_period);
+ write32(&mdp_intf->intf_vysnc_pulse_width_f0,
+ edid->mode.vspw * hsync_period);
+ write32(&mdp_intf->intf_disp_hctl, display_hctl);
+ write32(&mdp_intf->intf_disp_v_start_f0, display_vstart);
+ write32(&mdp_intf->intf_disp_v_end_f0, display_vend);
+ write32(&mdp_intf->intf_underflow_color, 0x00);
+ write32(&mdp_intf->intf_panel_format, 0x2100);
+}
+
+static void mdss_intf_fetch_start_config(struct edid *edid)
+{
+ uint32_t v_total, h_total, fetch_start, vfp_start;
+ uint32_t prefetch_avail, prefetch_needed;
+ uint32_t fetch_enable = BIT(31);
+
+ /*
+ * MDP programmable fetch is for MDP with rev >= 1.05.
+ * Programmable fetch is not needed if vertical back porch
+ * plus vertical puls width is >= 25.
+ */
+ if ((edid->mode.vbl - edid->mode.vso) >= MDSS_MDP_MAX_PREFILL_FETCH)
+ return;
+
+ /*
+ * Fetch should always be outside the active lines. If the fetching
+ * is programmed within active region, hardware behavior is unknown.
+ */
+ v_total = edid->mode.va + edid->mode.vbl;
+ h_total = edid->mode.ha + edid->mode.hbl;
+ vfp_start = edid->mode.va + edid->mode.vbl - edid->mode.vso;
+ prefetch_avail = v_total - vfp_start;
+ prefetch_needed = MDSS_MDP_MAX_PREFILL_FETCH - edid->mode.vbl + edid->mode.vso;
+
+ /*
+ * In some cases, vertical front porch is too high. In such cases limit
+ * the mdp fetch lines as the last (25 - vbp - vpw) lines of
+ * vertical front porch.
+ */
+ if (prefetch_avail > prefetch_needed)
+ prefetch_avail = prefetch_needed;
+
+ fetch_start = (v_total - prefetch_avail) * h_total + h_total + 1;
+ write32(&mdp_intf->intf_prof_fetch_start, fetch_start);
+ write32(&mdp_intf->intf_config, fetch_enable);
+}
+
+static void mdss_layer_mixer_setup(struct edid *edid)
+{
+ uint32_t mdp_rgb_size;
+ uint32_t left_staging_level;
+
+ /* write active region size*/
+ mdp_rgb_size = (edid->mode.va << 16) | edid->mode.ha;
+
+ write32(&mdp_layer_mixer->layer_out_size, mdp_rgb_size);
+ write32(&mdp_layer_mixer->layer_op_mode, 0x0);
+ for (int i = 0; i < 6; i++) {
+ write32(&mdp_layer_mixer->layer_blend[i].layer_blend_op, 0x100);
+ write32(&mdp_layer_mixer->layer_blend[i].layer_blend_const_alpha, 0x00ff0000);
+ }
+
+ /* Enable border fill */
+ left_staging_level = BIT(24);
+ left_staging_level |= BIT(1);
+
+ /* Base layer for layer mixer 0 */
+ write32(&mdp_ctl->ctl_layer0, left_staging_level);
+}
+
+static void mdss_vbif_qos_remapper_setup(void)
+{
+ /*
+ * VBIF remapper registers are used for translating internal display hardware
+ * priority level (from 0 to 7) into system fabric priority level.
+ * These remapper settings are defined for all the clients which corresponds
+ * to the xin clients connected to SSPP on VBIF.
+ */
+ write32(&vbif_rt->qos_rp_remap[0].vbif_xinl_qos_rp_remap, 0x00000003);
+ write32(&vbif_rt->qos_rp_remap[1].vbif_xinl_qos_rp_remap, 0x11111113);
+ write32(&vbif_rt->qos_rp_remap[2].vbif_xinl_qos_rp_remap, 0x22222224);
+ write32(&vbif_rt->qos_rp_remap[3].vbif_xinl_qos_rp_remap, 0x33333334);
+ write32(&vbif_rt->qos_rp_remap[4].vbif_xinl_qos_rp_remap, 0x44444445);
+ write32(&vbif_rt->qos_rp_remap[7].vbif_xinl_qos_rp_remap, 0x77777776);
+ write32(&vbif_rt->qos_lvl_remap[0].vbif_xinl_qos_lvl_remap, 0x00000003);
+ write32(&vbif_rt->qos_lvl_remap[1].vbif_xinl_qos_lvl_remap, 0x11111113);
+ write32(&vbif_rt->qos_lvl_remap[2].vbif_xinl_qos_lvl_remap, 0x22222224);
+ write32(&vbif_rt->qos_lvl_remap[3].vbif_xinl_qos_lvl_remap, 0x33333334);
+ write32(&vbif_rt->qos_lvl_remap[4].vbif_xinl_qos_lvl_remap, 0x44444445);
+ write32(&vbif_rt->qos_lvl_remap[5].vbif_xinl_qos_lvl_remap, 0x77777776);
+}
+
+void mdp_dsi_video_config(struct edid *edid)
+{
+ mdss_intf_tg_setup(edid);
+ mdss_intf_fetch_start_config(edid);
+ mdss_vbif_setup();
+ mdss_vbif_qos_remapper_setup();
+ mdss_source_pipe_config(edid);
+ mdss_layer_mixer_setup(edid);
+
+ /* Select Video Mode Interface */
+ write32(&mdp_ctl->ctl_top, 0x0);
+
+ /* PPB0 to INTF1 */
+ write32(&mdp_ctl->ctl_intf_active, BIT(1));
+ write32(&mdp_intf->intf_mux, 0x0F0000);
+}
+
+void mdp_dsi_video_on(void)
+{
+ uint32_t ctl0_reg_val;
+
+ ctl0_reg_val = VIG_0 | LAYER_MIXER_0 | CTL | INTF;
+ write32(&mdp_ctl->ctl_intf_flush, 0x2);
+ write32(&mdp_ctl->ctl_flush, ctl0_reg_val);
+}