summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--src/mainboard/google/gru/bootblock.c71
-rw-r--r--src/mainboard/google/gru/mainboard.c37
-rw-r--r--src/mainboard/google/gru/pwm_regulator.c5
3 files changed, 78 insertions, 35 deletions
diff --git a/src/mainboard/google/gru/bootblock.c b/src/mainboard/google/gru/bootblock.c
index 26af58cd81..0e916d298d 100644
--- a/src/mainboard/google/gru/bootblock.c
+++ b/src/mainboard/google/gru/bootblock.c
@@ -63,42 +63,73 @@ void bootblock_mainboard_early_init(void)
#endif
}
-static void speed_up_boot_cpu(void)
+static void configure_spi_flash(void)
{
- pwm_regulator_configure(PWM_REGULATOR_LIT, 1150);
+ gpio_input(GPIO(1, A, 7)); /* SPI1_MISO remove pull-up */
+ gpio_input(GPIO(1, B, 0)); /* SPI1_MOSI remove pull-up */
+ gpio_input(GPIO(1, B, 1)); /* SPI1_CLK remove pull-up */
+ gpio_input(GPIO(1, B, 2)); /* SPI1_CS remove pull-up */
- udelay(200);
+ rockchip_spi_init(CONFIG_BOOT_DEVICE_SPI_FLASH_BUS, 33*MHz);
+ rockchip_spi_set_sample_delay(CONFIG_BOOT_DEVICE_SPI_FLASH_BUS, 5);
- rkclk_configure_cpu(APLL_1512_MHZ, false);
+ write32(&rk3399_pmugrf->spi1_rxd, IOMUX_SPI1_RX);
+ write32(&rk3399_pmugrf->spi1_csclktx, IOMUX_SPI1_CSCLKTX);
}
-void bootblock_mainboard_init(void)
+static void configure_ec(void)
{
- speed_up_boot_cpu();
-
- if (rkclk_was_watchdog_reset())
- reboot_from_watchdog();
+ gpio_input(GPIO(2, C, 4)); /* SPI5_MISO remove pull-up */
+ gpio_input(GPIO(2, C, 5)); /* SPI5_MOSI remove pull-up */
+ gpio_input(GPIO(2, C, 6)); /* SPI5_CLK remove pull-up */
+ gpio_input_pullup(GPIO(2, C, 7)); /* SPI5_CS confirm pull-up */
- /* Set pinmux and configure spi flashrom. */
- write32(&rk3399_pmugrf->spi1_rxd, IOMUX_SPI1_RX);
- write32(&rk3399_pmugrf->spi1_csclktx, IOMUX_SPI1_CSCLKTX);
- rockchip_spi_init(CONFIG_BOOT_DEVICE_SPI_FLASH_BUS, 33000*KHz);
- rockchip_spi_set_sample_delay(CONFIG_BOOT_DEVICE_SPI_FLASH_BUS, 5);
+ rockchip_spi_init(CONFIG_EC_GOOGLE_CHROMEEC_SPI_BUS, 3093750);
- /* Set pinmux and configure EC SPI. */
write32(&rk3399_grf->iomux_spi5, IOMUX_SPI5);
- rockchip_spi_init(CONFIG_EC_GOOGLE_CHROMEEC_SPI_BUS, 3093750);
+}
+static void configure_tpm(void)
+{
if (IS_ENABLED(CONFIG_GRU_HAS_TPM2)) {
- /* Set pinmux and configure TPM SPI, which is not very fast. */
- write32(&rk3399_grf->iomux_spi0, IOMUX_SPI0);
+ gpio_input(GPIO(3, A, 4)); /* SPI0_MISO remove pull-up */
+ gpio_input(GPIO(3, A, 5)); /* SPI0_MOSI remove pull-up */
+ gpio_input(GPIO(3, A, 6)); /* SPI0_CLK remove pull-up */
+ gpio_input_pullup(GPIO(3, A, 7)); /* SPI0_CS confirm */
+
rockchip_spi_init(CONFIG_DRIVER_TPM_SPI_BUS, 1500*KHz);
+
+ write32(&rk3399_grf->iomux_spi0, IOMUX_SPI0);
} else {
- /* Set pinmux and configure TPM I2C */
+ gpio_input(GPIO(1, B, 7)); /* I2C0_SDA remove pull-up */
+ gpio_input(GPIO(1, C, 0)); /* I2C0_SCL remove pull-up */
+
+ i2c_init(0, 400*KHz);
+
write32(&rk3399_pmugrf->iomux_i2c0_scl, IOMUX_I2C0_SCL);
write32(&rk3399_pmugrf->iomux_i2c0_sda, IOMUX_I2C0_SDA);
- i2c_init(0, 400*KHz);
}
+}
+
+static void speed_up_boot_cpu(void)
+{
+ pwm_regulator_configure(PWM_REGULATOR_LIT, 1150);
+
+ udelay(200);
+
+ rkclk_configure_cpu(APLL_1512_MHZ, false);
+}
+
+void bootblock_mainboard_init(void)
+{
+ speed_up_boot_cpu();
+
+ if (rkclk_was_watchdog_reset())
+ reboot_from_watchdog();
+
+ configure_spi_flash();
+ configure_ec();
+ configure_tpm();
setup_chromeos_gpios();
}
diff --git a/src/mainboard/google/gru/mainboard.c b/src/mainboard/google/gru/mainboard.c
index a2b74badf2..8359ca49dc 100644
--- a/src/mainboard/google/gru/mainboard.c
+++ b/src/mainboard/google/gru/mainboard.c
@@ -94,19 +94,13 @@ static void configure_sdmmc(void)
gpio_output(GPIO(2, D, 4), 0); /* Keep the max voltage */
- /*
- * The SD card on this board is connected to port SDMMC0, which is
- * multiplexed with GPIO4B pins 0..5.
- *
- * Disable all pullups on these pins. For pullup configuration
- * register layout stacks banks 2 through 4 together, hence [2] means
- * group 4, [1] means bank B. This register is described on page 342
- * of section 1 of the TRM.
- *
- * Each GPIO pin's pull config takes two bits, writing zero to the
- * field disables pull ups/downs, as described on page 342 of rk3399
- * TRM Version 0.3 Part 1.
- */
+ gpio_input(GPIO(4, B, 0)); /* SDMMC0_D0 remove pull-up */
+ gpio_input(GPIO(4, B, 1)); /* SDMMC0_D1 remove pull-up */
+ gpio_input(GPIO(4, B, 2)); /* SDMMC0_D2 remove pull-up */
+ gpio_input(GPIO(4, B, 3)); /* SDMMC0_D3 remove pull-up */
+ gpio_input(GPIO(4, B, 4)); /* SDMMC0_CLK remove pull-down */
+ gpio_input(GPIO(4, B, 5)); /* SDMMC0_CMD remove pull-up */
+
write32(&rk3399_grf->gpio2_p[2][1], RK_CLRSETBITS(0xfff, 0));
/*
@@ -132,6 +126,16 @@ static void configure_sdmmc(void)
static void configure_codec(void)
{
+ gpio_input(GPIO(3, D, 0)); /* I2S0_SCLK remove pull-up */
+ gpio_input(GPIO(3, D, 1)); /* I2S0_RX remove pull-up */
+ gpio_input(GPIO(3, D, 2)); /* I2S0_TX remove pull-up */
+ gpio_input(GPIO(3, D, 3)); /* I2S0_SDI0 remove pull-up */
+ gpio_input(GPIO(3, D, 4)); /* I2S0_SDI1 remove pull-up */
+ /* GPIO3_D5 (I2S0_SDI2SDO2) not connected */
+ gpio_input(GPIO(3, D, 6)); /* I2S0_SDO1 remove pull-up */
+ gpio_input(GPIO(3, D, 7)); /* I2S0_SDO0 remove pull-up */
+ gpio_input(GPIO(4, A, 0)); /* I2S0_MCLK remove pull-up */
+
write32(&rk3399_grf->iomux_i2s0, IOMUX_I2S0);
write32(&rk3399_grf->iomux_i2sclk, IOMUX_I2SCLK);
@@ -206,10 +210,13 @@ static void enable_backlight_booster(void)
*/
udelay(1000);
- /* Select pinmux for i2c0, which is the display backlight booster. */
+ gpio_input(GPIO(1, B, 7)); /* I2C0_SDA remove pull_up */
+ gpio_input(GPIO(1, C, 0)); /* I2C0_SCL remove pull_up */
+
+ i2c_init(0, 100*KHz);
+
write32(&rk3399_pmugrf->iomux_i2c0_sda, IOMUX_I2C0_SDA);
write32(&rk3399_pmugrf->iomux_i2c0_scl, IOMUX_I2C0_SCL);
- i2c_init(0, 100*KHz);
for (i = 0; i < ARRAY_SIZE(i2c_writes); i++) {
i2c_buf[0] = i2c_writes[i].reg;
diff --git a/src/mainboard/google/gru/pwm_regulator.c b/src/mainboard/google/gru/pwm_regulator.c
index d6d2eecfb9..a81480a64d 100644
--- a/src/mainboard/google/gru/pwm_regulator.c
+++ b/src/mainboard/google/gru/pwm_regulator.c
@@ -17,6 +17,7 @@
#include <assert.h>
#include <boardid.h>
#include <console/console.h>
+#include <gpio.h>
#include <soc/grf.h>
#include <soc/pwm.h>
@@ -68,15 +69,19 @@ void pwm_regulator_configure(enum pwm_regulator pwm, int millivolt)
switch (pwm) {
case PWM_REGULATOR_GPU:
+ gpio_input(GPIO(4, C, 2)); /* PWM0 remove pull-down */
write32(&rk3399_grf->iomux_pwm_0, IOMUX_PWM_0);
break;
case PWM_REGULATOR_BIG:
+ gpio_input(GPIO(4, C, 6)); /* PWM1 remove pull-down */
write32(&rk3399_grf->iomux_pwm_1, IOMUX_PWM_1);
break;
case PWM_REGULATOR_LIT:
+ gpio_input(GPIO(1, C, 3)); /* PWM2 remove pull-down */
write32(&rk3399_pmugrf->iomux_pwm_2, IOMUX_PWM_2);
break;
case PWM_REGULATOR_CENTERLOG:
+ gpio_input(GPIO(0, A, 6)); /* PWM3 remove pull-down */
write32(&rk3399_pmugrf->iomux_pwm_3a, IOMUX_PWM_3_A);
break;
}