diff options
| -rw-r--r-- | src/mainboard/lippert/spacerunner-lx/Config.lb | 232 | ||||
| -rw-r--r-- | src/mainboard/lippert/spacerunner-lx/Options.lb | 209 | ||||
| -rw-r--r-- | src/mainboard/lippert/spacerunner-lx/cache_as_ram_auto.c | 235 | ||||
| -rw-r--r-- | src/mainboard/lippert/spacerunner-lx/chip.h | 28 | ||||
| -rw-r--r-- | src/mainboard/lippert/spacerunner-lx/irq_tables.c | 73 | ||||
| -rw-r--r-- | src/mainboard/lippert/spacerunner-lx/mainboard.c | 78 | ||||
| -rw-r--r-- | targets/lippert/spacerunner-lx/Config.lb | 60 |
7 files changed, 915 insertions, 0 deletions
diff --git a/src/mainboard/lippert/spacerunner-lx/Config.lb b/src/mainboard/lippert/spacerunner-lx/Config.lb new file mode 100644 index 0000000000..3175aaf86d --- /dev/null +++ b/src/mainboard/lippert/spacerunner-lx/Config.lb @@ -0,0 +1,232 @@ +## +## This file is part of the coreboot project. +## +## Copyright (C) 2008 LiPPERT Embedded Computers GmbH +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; either version 2 of the License, or +## (at your option) any later version. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +## +## Compute the location and size of where this firmware image +## (coreboot plus bootloader) will live in the boot rom chip. +## +if USE_FALLBACK_IMAGE + default ROM_SECTION_SIZE = FALLBACK_SIZE + default ROM_SECTION_OFFSET = (ROM_SIZE - FALLBACK_SIZE) +else + default ROM_SECTION_SIZE = (ROM_SIZE - FALLBACK_SIZE) + default ROM_SECTION_OFFSET = 0 +end + +## +## Compute the start location and size size of +## The coreboot bootloader. +## + +default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) +default PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE) + +## +## Compute where this copy of coreboot will start in the boot rom +## +default _ROMBASE = (CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE) + +## +## Compute a range of ROM that can cached to speed up coreboot, +## execution speed. +## +## XIP_ROM_SIZE must be a power of 2. +## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE +## +default XIP_ROM_SIZE = 64 * 1024 +default XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE) + +## +## Set all of the defaults for an x86 architecture +## +arch i386 end + +## +## Build the objects we have code for in this directory. +## + +driver mainboard.o + +if HAVE_PIRQ_TABLE + object irq_tables.o +end + +if USE_DCACHE_RAM + # compile cache_as_ram.c to auto.inc + makerule ./cache_as_ram_auto.inc + depends "$(MAINBOARD)/cache_as_ram_auto.c" + action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@" + action "perl -e 's/.rodata/.rom.data/g' -pi $@" + action "perl -e 's/.text/.section .rom.text/g' -pi $@" + end +end + +## +## Build our 16 bit and 32 bit coreboot entry code +## +mainboardinit cpu/x86/16bit/entry16.inc +mainboardinit cpu/x86/32bit/entry32.inc +ldscript /cpu/x86/16bit/entry16.lds +ldscript /cpu/x86/32bit/entry32.lds + +## +## Build our reset vector (This is where coreboot is entered) +## +if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds +else + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds +end + +### Should this be in the northbridge code? +#not in serengeti_cheetah mainboardinit arch/i386/lib/cpu_reset.inc + +## +## Include an ID string (For safe flashing) +## +mainboardinit arch/i386/lib/id.inc +ldscript /arch/i386/lib/id.lds + +### +### This is the early phase of coreboot startup. +### Things are delicate and we test to see if we should +### failover to another image. +### +if USE_FALLBACK_IMAGE + ldscript /arch/i386/lib/failover.lds +# mainboardinit ./failover.inc +end + +### +### O.k. We aren't just an intermediary anymore! +### + +## +## Setup RAM +## +mainboardinit cpu/x86/fpu/enable_fpu.inc + +if USE_DCACHE_RAM + mainboardinit cpu/amd/model_lx/cache_as_ram.inc + mainboardinit ./cache_as_ram_auto.inc +end + +## +## Include the secondary configuration files +## +dir /pc80 +config chip.h + +# See also SMC_CONFIG in cache_as_ram_auto.c. +# Bit0 turns off Live LED, bit1 switches Com1 to RS485, bit2 same for Com2. +register "sio_gp1x_config" = "0x01" + +chip northbridge/amd/lx + device pci_domain 0 on + device pci 1.0 on end # Northbridge + device pci 1.1 on end # Graphics + device pci 1.2 on end # AES + chip southbridge/amd/cs5536 + # IRQ 12 and 1 unmasked, keyboard and mouse IRQs. OK + # SIRQ Mode = Active(Quiet) mode. Save power.... + # Invert mask = IRQ 12 and 1 are active high. Keyboard and mouse, + # UARTs, etc IRQs. OK + register "lpc_serirq_enable" = "0x000012DA" # 00010010 11011010 + register "lpc_serirq_polarity" = "0x0000ED25" # inverse of above + register "lpc_serirq_mode" = "1" + register "enable_gpio_int_route" = "0x0D0C0700" + register "enable_ide_nand_flash" = "0" # 0:ide mode, 1:flash + register "enable_USBP4_device" = "0" # 0:host, 1:device + register "enable_USBP4_overcurrent" = "0" # 0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381) + register "com1_enable" = "0" + register "com1_address" = "0x3E8" + register "com1_irq" = "6" + register "com2_enable" = "0" + register "com2_address" = "0x2E8" + register "com2_irq" = "6" + register "unwanted_vpci[0]" = "0x80007B00" # Audio: 1<<31 + Device 0x0F<<11 + Function 3<<8 + register "unwanted_vpci[1]" = "0" # End of list has a zero + device pci 8.0 on end # Slot4 + device pci 9.0 on end # Slot3 + device pci a.0 on end # Slot2 + device pci b.0 on end # Slot1 + device pci c.0 on end # IT8888 + device pci e.0 on end # Ethernet + device pci f.0 on # ISA Bridge + chip superio/ite/it8712f + device pnp 2e.0 off # Floppy + io 0x60 = 0x3f0 + irq 0x70 = 6 + drq 0x74 = 2 + end + device pnp 2e.1 on # Com1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + device pnp 2e.2 on # Com2 + io 0x60 = 0x2f8 + irq 0x70 = 3 + end + device pnp 2e.3 on # Parallel port + io 0x60 = 0x378 + irq 0x70 = 7 + end + device pnp 2e.4 on # EC + io 0x60 = 0x290 + io 0x62 = 0x230 + irq 0x70 = 9 + end + device pnp 2e.5 on # PS/2 keyboard + io 0x60 = 0x60 + io 0x62 = 0x64 + irq 0x70 = 1 + end + device pnp 2e.6 on # PS/2 mouse + irq 0x70 = 12 + end + device pnp 2e.7 on # GPIO + io 0x62 = 0x1220 + io 0x64 = 0x1200 + end + device pnp 2e.8 off # MIDI + io 0x60 = 0x300 + irq 0x70 = 9 + end + device pnp 2e.9 off # Game port + io 0x60 = 0x220 + end + device pnp 2e.a off end # CIR + end + end + device pci f.2 on end # IDE + device pci f.3 off end # Audio + device pci f.4 on end # OHCI + device pci f.5 on end # EHCI + end + end + # APIC cluster is late CPU init. + device apic_cluster 0 on + chip cpu/amd/model_lx + device apic 0 on end + end + end +end diff --git a/src/mainboard/lippert/spacerunner-lx/Options.lb b/src/mainboard/lippert/spacerunner-lx/Options.lb new file mode 100644 index 0000000000..4b524c2023 --- /dev/null +++ b/src/mainboard/lippert/spacerunner-lx/Options.lb @@ -0,0 +1,209 @@ +## +## This file is part of the coreboot project. +## +## Copyright (C) 2008 LiPPERT Embedded Computers GmbH +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; either version 2 of the License, or +## (at your option) any later version. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses HAVE_OPTION_TABLE +uses USE_OPTION_TABLE +uses CONFIG_ROM_PAYLOAD +uses CONFIG_IDE +uses CONFIG_FS_PAYLOAD +uses CONFIG_FS_EXT2 +uses AUTOBOOT_DELAY +uses AUTOBOOT_CMDLINE +uses IRQ_SLOT_COUNT +uses MAINBOARD +uses MAINBOARD_VENDOR +uses MAINBOARD_PART_NUMBER +uses COREBOOT_EXTRA_VERSION +uses ARCH +uses FALLBACK_SIZE +uses STACK_SIZE +uses HEAP_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_PAYLOAD_START +uses CONFIG_COMPRESS +uses CONFIG_COMPRESSED_PAYLOAD_NRV2B +uses CONFIG_COMPRESSED_PAYLOAD_LZMA +uses CONFIG_PRECOMPRESSED_PAYLOAD +uses PAYLOAD_SIZE +uses _ROMBASE +uses _RAMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses HAVE_MP_TABLE +uses CROSS_COMPILE +uses CC +uses HOSTCC +uses OBJCOPY +uses DEBUG +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses CONFIG_CONSOLE_SERIAL8250 +uses TTYS0_BAUD +uses TTYS0_BASE +uses TTYS0_LCS +uses CONFIG_UDELAY_TSC +uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 +uses CONFIG_CONSOLE_VGA +uses CONFIG_PCI_ROM_RUN +uses CONFIG_VIDEO_MB +uses USE_DCACHE_RAM +uses DCACHE_RAM_BASE +uses DCACHE_RAM_SIZE +uses PIRQ_ROUTE + +## ROM_SIZE is the size of boot ROM that this board will use. +default ROM_SIZE = 512*1024 + +### +### Build options +### +default CONFIG_CONSOLE_VGA = 0 +default CONFIG_VIDEO_MB = 8 +default CONFIG_PCI_ROM_RUN = 0 + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT = 1 + +## +## no MP table +## +default HAVE_MP_TABLE = 0 + +## +## Build code to reset the motherboard from coreboot +## +default HAVE_HARD_RESET = 0 + +## Delay timer options +## +default CONFIG_UDELAY_TSC = 1 +default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE = 1 +default IRQ_SLOT_COUNT = 7 +default PIRQ_ROUTE = 1 + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE = 0 + +### +### coreboot layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy. +default ROM_IMAGE_SIZE = 64 * 1024 +default FALLBACK_SIZE = 128 * 1024 + +## +## enable CACHE_AS_RAM specifics +## +default USE_DCACHE_RAM = 1 +default DCACHE_RAM_BASE = 0xc8000 +default DCACHE_RAM_SIZE = 0x08000 + +## +## Use a small 8K stack +## +default STACK_SIZE = 0x2000 + +## +## Use a small 16K heap +## +default HEAP_SIZE = 0x4000 + +## +## Only use the option table in a normal image +## +#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE +default USE_OPTION_TABLE = 0 + +default _RAMBASE = 0x00004000 + +default CONFIG_ROM_PAYLOAD = 1 + +## +## The default compiler +## +default CROSS_COMPILE = "" +default CC = "$(CROSS_COMPILE)gcc -m32" +default HOSTCC = "gcc" + +## +## The Serial Console +## + +# To Enable the Serial Console +default CONFIG_CONSOLE_SERIAL8250 = 1 + +## Select the serial console baud rate +default TTYS0_BAUD = 115200 +#default TTYS0_BAUD = 57600 +#default TTYS0_BAUD = 38400 +#default TTYS0_BAUD = 19200 +#default TTYS0_BAUD = 9600 +#default TTYS0_BAUD = 4800 +#default TTYS0_BAUD = 2400 +#default TTYS0_BAUD = 1200 + +# Select the serial console base port +default TTYS0_BASE = 0x3f8 + +# Select the serial protocol +# This defaults to 8 data bits, 1 stop bit, and no parity +default TTYS0_LCS = 0x3 + +# Compile extra debugging code +default DEBUG = 1 + +## +### Select the coreboot loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +default DEFAULT_CONSOLE_LOGLEVEL = 8 +## At a maximum only compile in this level of debugging +default MAXIMUM_CONSOLE_LOGLEVEL = 8 + +end diff --git a/src/mainboard/lippert/spacerunner-lx/cache_as_ram_auto.c b/src/mainboard/lippert/spacerunner-lx/cache_as_ram_auto.c new file mode 100644 index 0000000000..701e32fa6d --- /dev/null +++ b/src/mainboard/lippert/spacerunner-lx/cache_as_ram_auto.c @@ -0,0 +1,235 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2007 Advanced Micro Devices, Inc. + * Copyright (C) 2008 LiPPERT Embedded Computers GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#define ASSEMBLY 1 + +#include <stdlib.h> +#include <stdint.h> +#include <spd.h> +#include <device/pci_def.h> +#include <arch/io.h> +#include <device/pnp_def.h> +#include <arch/hlt.h> +#include "pc80/serial.c" +#include "arch/i386/lib/console.c" +#include "ram/ramtest.c" +#include "cpu/x86/bist.h" +#include "cpu/x86/msr.h" +#include <cpu/amd/lxdef.h> +#include <cpu/amd/geode_post_code.h> +#include "southbridge/amd/cs5536/cs5536.h" + +#define POST_CODE(x) outb(x, 0x80) + +#include "southbridge/amd/cs5536/cs5536_early_smbus.c" +#include "southbridge/amd/cs5536/cs5536_early_setup.c" +#include "superio/ite/it8712f/it8712f_early_serial.c" + +/* Bit0 enables Spread Spectrum, bit1 makes on-board SSD act as IDE slave. */ +#define SMC_CONFIG 0x01 + +#define ManualConf 1 /* No automatic strapped PLL config */ +#define PLLMSRhi 0x0000059C /* Manual settings for the PLL */ +#define PLLMSRlo 0x00DE6001 +#define DIMM0 0xA0 +#define DIMM1 0xA2 + +static const unsigned char spdbytes[] = { // 4x Promos V58C2512164SA-J5I + 0xFF, 0xFF, // only values used by Geode-LX raminit.c are set + [SPD_MEMORY_TYPE] = SPD_MEMORY_TYPE_SDRAM_DDR, // (Fundamental) memory type + [SPD_NUM_ROWS] = 0x0D, // Number of row address bits [13] + [SPD_NUM_COLUMNS] = 0x0A, // Number of column address bits [10] + [SPD_NUM_DIMM_BANKS] = 1, // Number of module rows (banks) + 0xFF, 0xFF, 0xFF, + [SPD_MIN_CYCLE_TIME_AT_CAS_MAX] = 0x50, // SDRAM cycle time (highest CAS latency), RAS access time (tRAC) [5.0 ns in BCD] + 0xFF, 0xFF, + [SPD_REFRESH] = 0x82, // Refresh rate/type [Self Refresh, 7.8 us] + [SPD_PRIMARY_SDRAM_WIDTH] = 64, // SDRAM width (primary SDRAM) [64 bits] + 0xFF, 0xFF, 0xFF, + [SPD_NUM_BANKS_PER_SDRAM] = 4, // SDRAM device attributes, number of banks on SDRAM device + [SPD_ACCEPTABLE_CAS_LATENCIES] = 0x1C, // SDRAM device attributes, CAS latency [3, 2.5, 2] + 0xFF, 0xFF, + [SPD_MODULE_ATTRIBUTES] = 0x20, // SDRAM module attributes [differential clk] + [SPD_DEVICE_ATTRIBUTES_GENERAL] = 0x40, // SDRAM device attributes, general [Concurrent AP] + [SPD_SDRAM_CYCLE_TIME_2ND] = 0x60, // SDRAM cycle time (2nd highest CAS latency) [6.0 ns in BCD] + 0xFF, + [SPD_SDRAM_CYCLE_TIME_3RD] = 0x75, // SDRAM cycle time (3rd highest CAS latency) [7.5 ns in BCD] + 0xFF, + [SPD_tRP] = 60, // Min. row precharge time [15 ns in units of 0.25 ns] + [SPD_tRRD] = 40, // Min. row active to row active [10 ns in units of 0.25 ns] + [SPD_tRCD] = 60, // Min. RAS to CAS delay [15 ns in units of 0.25 ns] + [SPD_tRAS] = 40, // Min. RAS pulse width = active to precharge delay [40 ns] + [SPD_BANK_DENSITY] = 0x40, // Density of each row on module [256 MB] + 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, + [SPD_tRFC] = 70 // SDRAM Device Minimum Auto Refresh to Active/Auto Refresh [70 ns] +}; + +static inline int spd_read_byte(unsigned int device, unsigned int address) +{ + if (device != DIMM0) + return 0xFF; /* No DIMM1, don't even try. */ + +#if DEBUG + if (address >= sizeof(spdbytes) || spdbytes[address] == 0xFF) { + print_err("ERROR: spd_read_byte(DIMM0, 0x"); + print_err_hex8(address); + print_err(") returns 0xff\r\n"); + } +#endif + + /* Fake SPD ROM value */ + return (address < sizeof(spdbytes)) ? spdbytes[address] : 0xFF; +} + +/* Send config data to System Management Controller via SMB. */ +static int smc_send_config(unsigned char config_data) +{ + if (smbus_check_stop_condition(SMBUS_IO_BASE)) + return 1; + if (smbus_start_condition(SMBUS_IO_BASE)) + return 2; + if (smbus_send_slave_address(SMBUS_IO_BASE, 0x50)) // SMC address + return 3; + if (smbus_send_command(SMBUS_IO_BASE, 0x28)) // set config data + return 4; + if (smbus_send_command(SMBUS_IO_BASE, 0x01)) // data length + return 5; + if (smbus_send_command(SMBUS_IO_BASE, config_data)) + return 6; + smbus_stop_condition(SMBUS_IO_BASE); + return 0; +} + +#include "northbridge/amd/lx/raminit.h" +#include "northbridge/amd/lx/pll_reset.c" +#include "northbridge/amd/lx/raminit.c" +#include "sdram/generic_sdram.c" +#include "cpu/amd/model_lx/cpureginit.c" +#include "cpu/amd/model_lx/syspreinit.c" + +static void msr_init(void) +{ + msr_t msr; + + /* Setup access to the cache for under 1MB. */ + msr.hi = 0x24fffc02; + msr.lo = 0x1000A000; /* 0-A0000 write back */ + wrmsr(CPU_RCONF_DEFAULT, msr); + + msr.hi = 0x0; /* Write back */ + msr.lo = 0x0; + wrmsr(CPU_RCONF_A0_BF, msr); + wrmsr(CPU_RCONF_C0_DF, msr); + wrmsr(CPU_RCONF_E0_FF, msr); + + /* Setup access to the cache for under 640K. Note MC not setup yet. */ + msr.hi = 0x20000000; + msr.lo = 0xfff80; + wrmsr(MSR_GLIU0 + 0x20, msr); + + msr.hi = 0x20000000; + msr.lo = 0x80fffe0; + wrmsr(MSR_GLIU0 + 0x21, msr); + + msr.hi = 0x20000000; + msr.lo = 0xfff80; + wrmsr(MSR_GLIU1 + 0x20, msr); + + msr.hi = 0x20000000; + msr.lo = 0x80fffe0; + wrmsr(MSR_GLIU1 + 0x21, msr); +} + +static const u16 sio_init_table[] = { // hi=data, lo=index + 0x0707, // select LDN 7 (GPIO, SPI, watchdog, ...) + 0x1E2C, // disable ATXPowerGood + 0x0423, // don't delay POWerOK1/2 + 0x9072, // watchdog triggers POWOK, counts seconds +#if !USE_WATCHDOG_ON_BOOT + 0x0073, 0x0074, // disable watchdog by setting timeout to 0 +#endif + 0xBF25, 0x172A, 0xF326, // select GPIO function for most pins + 0xFF27, 0xDF28, 0x2729, // (GP45=SUSB, GP23,22,16,15=SPI, GP13=PWROK1) + 0x072C, // VIN6=enabled?, FAN4/5 disabled, VIN7=internal, VIN3=internal + 0x66B8, 0x0CB9, // enable pullups + 0x07C0, // enable Simple-I/O for GP12-10= RS485_EN2,1, LIVE_LED + 0x07C8, // config GP12-10 as output + 0x2DF5, // map Hw Monitor Thermal Output to GP55 + 0x08F8, // map GP LED Blinking 1 to GP10=LIVE_LED (deactivate Simple I/O to use) +}; + +/* Early mainboard specific GPIO setup. */ +static void mb_gpio_init(void) +{ + int i; + + /* Init Super I/O WDT, GPIOs. Done early, WDT init may trigger reset! */ + it8712f_enter_conf(); + for (i = 0; i < ARRAY_SIZE(sio_init_table); i++) { + u16 val = sio_init_table[i]; + outb((u8)val, SIO_INDEX); + outb(val >> 8, SIO_DATA); + } + it8712f_exit_conf(); +} + +void cache_as_ram_main(void) +{ + int err; + POST_CODE(0x01); + + static const struct mem_controller memctrl[] = { + {.channel0 = {(0xa << 3) | 0, (0xa << 3) | 1}} + }; + + SystemPreInit(); + msr_init(); + + cs5536_early_setup(); + + /* + * Note: Must do this AFTER the early_setup! It is counting on some + * early MSR setup for CS5536. + */ + it8712f_enable_serial(0, TTYS0_BASE); // Does not use its 1st parameter + mb_gpio_init(); + uart_init(); + console_init(); + + pll_reset(ManualConf); + + cpuRegInit(); + + /* bit1 = on-board IDE is slave, bit0 = Spread Spectrum */ + if ((err = smc_send_config(SMC_CONFIG))) { + print_err("ERROR "); + print_err_char('0'+err); + print_err(" sending config data to SMC\r\n"); + } + + sdram_initialize(1, memctrl); + + /* Check memory. */ + /* ram_check(0, 640 * 1024); */ + + /* Memory is setup. Return to cache_as_ram.inc and continue to boot. */ + return; +} diff --git a/src/mainboard/lippert/spacerunner-lx/chip.h b/src/mainboard/lippert/spacerunner-lx/chip.h new file mode 100644 index 0000000000..ba7edb0a1d --- /dev/null +++ b/src/mainboard/lippert/spacerunner-lx/chip.h @@ -0,0 +1,28 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 LiPPERT Embedded Computers GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <stdint.h> + +extern struct chip_operations mainboard_lippert_spacerunner_lx_ops; + +struct mainboard_lippert_spacerunner_lx_config { + /* bit2 = RS485_EN2, bit1 = RS485_EN1, bit0 = Live LED */ + u8 sio_gp1x_config; +}; diff --git a/src/mainboard/lippert/spacerunner-lx/irq_tables.c b/src/mainboard/lippert/spacerunner-lx/irq_tables.c new file mode 100644 index 0000000000..1bf04eb7de --- /dev/null +++ b/src/mainboard/lippert/spacerunner-lx/irq_tables.c @@ -0,0 +1,73 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 LiPPERT Embedded Computers GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <arch/pirq_routing.h> +#include <console/console.h> +#include <arch/io.h> +#include <arch/pirq_routing.h> +#include "../../../southbridge/amd/cs5536/cs5536.h" + +/* Platform IRQs */ +#define PIRQA 10 +#define PIRQB 11 +#define PIRQC 5 +#define PIRQD 15 + +/* Map */ +#define M_PIRQA (1 << PIRQA) /* Bitmap of supported IRQs */ +#define M_PIRQB (1 << PIRQB) /* Bitmap of supported IRQs */ +#define M_PIRQC (1 << PIRQC) /* Bitmap of supported IRQs */ +#define M_PIRQD (1 << PIRQD) /* Bitmap of supported IRQs */ + +/* Link */ +#define L_PIRQA 1 /* Means Slot INTx# Connects To Chipset INTA# */ +#define L_PIRQB 2 /* Means Slot INTx# Connects To Chipset INTB# */ +#define L_PIRQC 3 /* Means Slot INTx# Connects To Chipset INTC# */ +#define L_PIRQD 4 /* Means Slot INTx# Connects To Chipset INTD# */ + +const struct irq_routing_table intel_irq_routing_table = { + PIRQ_SIGNATURE, /* u32 signature */ + PIRQ_VERSION, /* u16 version */ + 32 + 16 * IRQ_SLOT_COUNT,/* There can be total 7 devices on the bus */ + 0x00, /* Where the interrupt router lies (bus) */ + (0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */ + 0x00, /* IRQs devoted exclusively to PCI usage */ + 0x100B, /* Vendor */ + 0x002B, /* Device */ + 0, /* Crap (miniport) */ + {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */ + 0xE0, /* u8 checksum, this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */ + { + /* If you change the number of entries, change the IRQ_SLOT_COUNT above! */ + /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */ + {0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* CPU */ + {0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */ + {0x00, (0x0E << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* ethernet */ + {0x00, (0x0B << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x1, 0x0}, /* slot1 */ + {0x00, (0x0A << 3) | 0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}}, 0x2, 0x0}, /* slot2 */ + {0x00, (0x09 << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}}, 0x3, 0x0}, /* slot3 */ + {0x00, (0x08 << 3) | 0x0, {{L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}}, 0x4, 0x0}, /* slot4 */ + } +}; + +unsigned long write_pirq_routing_table(unsigned long addr) +{ + return copy_pirq_routing_table(addr); +} diff --git a/src/mainboard/lippert/spacerunner-lx/mainboard.c b/src/mainboard/lippert/spacerunner-lx/mainboard.c new file mode 100644 index 0000000000..010f561516 --- /dev/null +++ b/src/mainboard/lippert/spacerunner-lx/mainboard.c @@ -0,0 +1,78 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 LiPPERT Embedded Computers GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <stdlib.h> +#include <stdint.h> +#include <console/console.h> +#include <device/device.h> +#include <arch/io.h> +#include <device/pci.h> +#include <device/pci_ids.h> +#include "chip.h" + +static const u16 ec_init_table[] = { /* hi=data, lo=index */ + 0x1900, /* Enable monitoring */ + 0x3050, /* VIN4,5 enabled */ + 0x0351, /* TMPIN1,2 diode mode, TMPIN3 off */ + 0x805C, /* Unlock zero adjust */ + 0x7056, 0x3C57, /* Zero adjust TMPIN1,2 */ + 0x005C, /* Lock zero adjust */ + 0xD014 /* Also set FAN_CTL polarity to Active High */ +}; + +static void init(struct device *dev) +{ + struct mainboard_lippert_spacerunner_lx_config *mb = dev->chip_info; + unsigned int gpio_base, i; + printk_debug("LiPPERT SpaceRunner-LX ENTER %s\n", __FUNCTION__); + + /* Init CS5536 GPIOs */ + gpio_base = pci_read_config32(dev_find_device(PCI_VENDOR_ID_AMD, + PCI_DEVICE_ID_AMD_CS5536_ISA, 0), PCI_BASE_ADDRESS_1) - 1; + + outl(0x00000040, gpio_base + 0x00); // GPIO6 value 1 - LAN_PD# + outl(0x00000040, gpio_base + 0x04); // GPIO6 output 1 - LAN_PD# + outl(0x04000000, gpio_base + 0x18); // GPIO10 pull up 0 - THRM_ALRM# + outl(0x00000400, gpio_base + 0x34); // GPIO10 in aux1 1 - THRM_ALRM# + outl(0x00000400, gpio_base + 0x20); // GPIO10 input 1 - THRM_ALRM# + outl(0x00000800, gpio_base + 0x94); // GPIO27 out aux2 1 - 32kHz + outl(0x00000800, gpio_base + 0x84); // GPIO27 output 1 - 32kHz + outl(0x08000000, gpio_base + 0x98); // GPIO27 pull up 0 - 32kHz + + /* Init Environment Controller. */ + for (i = 0; i < ARRAY_SIZE(ec_init_table); i++) { + u16 val = ec_init_table[i]; + outb((u8)val, 0x0295); + outb(val >> 8, 0x0296); + } + + outb(mb->sio_gp1x_config, 0x1220); /* Simple-I/O GP17-10 */ + printk_debug("LiPPERT SpaceRunner-LX EXIT %s\n", __FUNCTION__); +} + +static void enable_dev(struct device *dev) +{ + dev->ops->init = init; +} + +struct chip_operations mainboard_lippert_spacerunner_lx_ops = { + CHIP_NAME("LiPPERT SpaceRunner-LX Mainboard") + .enable_dev = enable_dev, +}; diff --git a/targets/lippert/spacerunner-lx/Config.lb b/targets/lippert/spacerunner-lx/Config.lb new file mode 100644 index 0000000000..cc57b00150 --- /dev/null +++ b/targets/lippert/spacerunner-lx/Config.lb @@ -0,0 +1,60 @@ +## +## This file is part of the coreboot project. +## +## Copyright (C) 2008 LiPPERT Embedded Computers GmbH +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; either version 2 of the License, or +## (at your option) any later version. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +# Config file for the LiPPERT Cool SpaceRunner-LX. --JR 10/2008 + +target spacerunner-lx +mainboard lippert/spacerunner-lx + +# HACK to get the right TSC support. +option CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 = 1 + +option CONFIG_COMPRESSED_PAYLOAD_NRV2B = 0 +option CONFIG_COMPRESSED_PAYLOAD_LZMA = 0 + +## Load payload (e.g. Linux) from IDE. +#option CONFIG_ROM_PAYLOAD = 0 +#option CONFIG_IDE = 1 +#option CONFIG_FS_PAYLOAD = 1 +#option CONFIG_FS_EXT2 = 1 +#option AUTOBOOT_DELAY = 0 +#option AUTOBOOT_CMDLINE = "hda1:/payload.elf" + +# Leave 36k for VSA. Board is equipped with a 1 MB SPI flash, however, due to +# limitations of the IT8712F Super I/O, only the top 512 KB are directly mapped. +option ROM_SIZE = (512 * 1024) - (36 * 1024) +option FALLBACK_SIZE = ROM_SIZE + +#option DEFAULT_CONSOLE_LOGLEVEL = 4 +#option MAXIMUM_CONSOLE_LOGLEVEL = 4 + +# Saves space on ROM_IMAGE_SIZE, but decompression costs a second on boot. +option CONFIG_COMPRESS = 1 + +romimage "image" + option USE_FALLBACK_IMAGE = 1 + option ROM_IMAGE_SIZE = 64 * 1024 + option COREBOOT_EXTRA_VERSION = ".0" + payload ../payload.elf + # If getting payload from IDE + # payload /dev/null +end + +buildrom ./coreboot.rom ROM_SIZE "image" |