diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/mainboard/asrock/h110m-dvs.md | 162 | ||||
| -rw-r--r-- | Documentation/mainboard/index.md | 1 |
2 files changed, 163 insertions, 0 deletions
diff --git a/Documentation/mainboard/asrock/h110m-dvs.md b/Documentation/mainboard/asrock/h110m-dvs.md new file mode 100644 index 0000000000..614669b154 --- /dev/null +++ b/Documentation/mainboard/asrock/h110m-dvs.md @@ -0,0 +1,162 @@ +# ASRock H110M-DVS + +This page describes how to run coreboot on the [ASRock H110M-DVS]. + +## Required proprietary blobs + +Mainboard is based on Intel Skylake/Kaby Lake processor and H110 Chipset. +Intel company provides [Firmware Support Package (2.0)](../../Documentation/soc/intel/fsp/index.md) +(intel FSP 2.0) to initialize this generation silicon. Please see this +[document](../../Documentation/soc/intel/code_development_model/code_development_model.md). + +FSP Information: + +```eval_rst ++-----------------------------+-------------------+-------------------+ +| FSP Project Name | Directory | Specification | ++-----------------------------+-------------------+-------------------+ +| 7th Generation Intel® Core™ | KabylakeFspBinPkg | 2.0 | +| processors and chipsets | | | +| (formerly Kaby Lake) | | | ++-----------------------------+-------------------+-------------------+ +``` + +Please take FSP from the directory `3rdparty/fsp/KabylakeFspBinPkg/` in +the coreboot or download the latest version from [github][FSP github]. + +You must use [Intel Binary Configuration Tool] BCT to set the following +parameters in FSP.fd to initialize the PEG x16 port: + +``` +Peg0Enable = Enable +Peg0MaxLinkSpeed = Gen3 +Peg0MaxLinkWidth = Auto +``` + +BCT creates Fsp_M.fd, Fsp_S.fd and Fsp_T.fd. These files are integrated +into the coreboot image. If PEG port is not used, you can get these files +without BTC: + +```bash +# split FSP.fd +python 3rdparty/fsp/Tools/SplitFspBin.py split -f 3rdparty/fsp/KabylakeFspBinPkg/Fsp.fd +``` + +## Building coreboot + +The following steps set the default parameters for this board to build a +fully working image: + +```bash +make distclean +touch .config +./util/scripts/config --enable VENDOR_ASROCK +./util/scripts/config --enable BOARD_ASROCK_H110M_DVS +./util/scripts/config --enable CONFIG_ADD_FSP_BINARIES +./util/scripts/config --set-str CONFIG_FSP_M_FILE "/path/to/Fsp_M.fd" +./util/scripts/config --set-str CONFIG_FSP_S_FILE "/path/to/Fsp_S.fd" +./util/scripts/config --set-str REALTEK_8168_MACADDRESS "xx:xx:xx:xx:xx:xx" +make olddefconfig +``` + +However, it is strongly advised to use `make menuconfig` afterwards +(or instead), so that you can see all of the settings. + +Use the following command to disable the serial console if debugging +output is not required: + +```bash +./util/scripts/config --disable CONSOLE_SERIAL +``` + +However, a more flexible method is to change the console log level from +within an OS using `util/nvramtool`, or with the `nvramcui` payload. + +Now, run `make` to build the coreboot image. + +## Flashing coreboot + +### Internal programming + +The main SPI flash can be accessed using [flashrom]. By default, only +the BIOS region of the flash is writable. If you wish to change any +other region, such as the Management Engine or firmware descriptor, then +an external programmer is required (unless you find a clever way around +the flash protection). More information about this [here](../../Documentation/flash_tutorial/index.md). + +### External programming + +The flash chip is a 8 MiB socketed DIP-8 chip. Specifically, it's a +Macronix MX25L6473E, whose datasheet can be found [here][MX25L6473E]. +The chip is located to the bottom right-hand side of the board. For +a precise location, refer to section 1.3 (Motherboard Layout) of the +[H110M-DVS manual], where the chip is labelled "64Mb BIOS". Take note of +the chip's orientation, remove it from its socket, and flash it with +an external programmer. For reference, the notch in the chip should be +facing towards the bottom of the board. + +## Known issues + +- The VGA port doesn't work. + +- PEG x16 port training correctly runs only at link speed of 2.5GT/s(gen1). + It takes more time to research the schematic of this board. + +- SuperIO GPIO pin is used to reset Realtek chip. However, since the + Logical Device 7 (GPIO6, GPIO7, GPIO8) is not initialized, the network + chip is in a reset state all the time. + +## Untested + +- parallel port +- PS/2 keyboard +- PS/2 mouse +- EHCI debug +- TPM +- infrared module +- chassis intrusion header +- chassis speaker header + +## Working + +- integrated graphics init with libgfxinit (see [Known issues](#known-issues)) +- PCIe x1 +- PEG x16 Gen1 (see [Known issues](#known-issues)) +- SATA +- USB +- serial port +- onboard audio +- using `me_cleaner` +- using `flashrom` + +## TODO + +- PEG x16 Gen3 +- NCT6791D GPIOs +- onboard network (see [Known issues](#known-issues)) +- S3 suspend/resume +- Wake-on-LAN +- hardware monitor + +## Technology + +```eval_rst ++------------------+--------------------------------------------------+ +| CPU | Intel Skylake/Kaby Lake (LGA1151) | ++------------------+--------------------------------------------------+ +| PCH | Intel Sunrise Point H110 | ++------------------+--------------------------------------------------+ +| Super I/O | Nuvoton NCT6791D | ++------------------+--------------------------------------------------+ +| EC | None | ++------------------+--------------------------------------------------+ +| Coprocessor | Intel Management Engine | ++------------------+--------------------------------------------------+ +``` + +[ASRock H110M-DVS]: https://www.asrock.com/mb/Intel/H110M-DVS%20R2.0/ +[FSP github]: https://github.com/IntelFsp/FSP +[Intel Binary Configuration Tool]: https://github.com/IntelFsp/BCT +[MX25L6473E]: http://www.macronix.com/Lists/Datasheet/Attachments/7380/MX25L6473E,%203V,%2064Mb,%20v1.4.pdf +[flashrom]: https://flashrom.org/Flashrom +[H110M-DVS manual]: http://asrock.pc.cdn.bitgravity.com/Manual/H110M-DVS%20R2.0.pdf diff --git a/Documentation/mainboard/index.md b/Documentation/mainboard/index.md index 56adb25477..d94c23e2f7 100644 --- a/Documentation/mainboard/index.md +++ b/Documentation/mainboard/index.md @@ -10,6 +10,7 @@ This section contains documentation about coreboot on specific mainboards. ## ASRock - [H81M-HDS](asrock/h81m-hds.md) +- [H110M-DVS](asrock/h110m-dvs.md) ## Cavium |