diff options
Diffstat (limited to 'src/cpu/samsung/exynos5250/dmc.h')
| -rw-r--r-- | src/cpu/samsung/exynos5250/dmc.h | 98 |
1 files changed, 98 insertions, 0 deletions
diff --git a/src/cpu/samsung/exynos5250/dmc.h b/src/cpu/samsung/exynos5250/dmc.h index 9b1f29305d..0814c07afb 100644 --- a/src/cpu/samsung/exynos5250/dmc.h +++ b/src/cpu/samsung/exynos5250/dmc.h @@ -175,6 +175,10 @@ enum mem_manuf { MEM_MANUF_COUNT = 2, // fancy that. }; +enum { + MEM_TIMINGS_MSR_COUNT = 4, +}; + #define DMC_INTERLEAVE_SIZE 0x1f /* CONCONTROL register fields */ @@ -224,5 +228,99 @@ enum mem_manuf { #define PHY_CON42_CTRL_RDLAT_SHIFT 0 #define PHY_CON42_CTRL_RDLAT_MASK (0x1f << PHY_CON42_CTRL_RDLAT_SHIFT) +/* These are the memory timings for a particular memory type and speed */ +struct mem_timings { + enum mem_manuf mem_manuf; /* Memory manufacturer */ + enum ddr_mode mem_type; /* Memory type */ + unsigned int frequency_mhz; /* Frequency of memory in MHz */ + + /* Here follow the timing parameters for the selected memory */ + uint8_t apll_mdiv; + uint8_t apll_pdiv; + uint8_t apll_sdiv; + uint8_t mpll_mdiv; + uint8_t mpll_pdiv; + uint8_t mpll_sdiv; + uint8_t cpll_mdiv; + uint8_t cpll_pdiv; + uint8_t cpll_sdiv; + uint8_t gpll_pdiv; + uint16_t gpll_mdiv; + uint8_t gpll_sdiv; + uint8_t epll_mdiv; + uint8_t epll_pdiv; + uint8_t epll_sdiv; + uint8_t vpll_mdiv; + uint8_t vpll_pdiv; + uint8_t vpll_sdiv; + uint8_t bpll_mdiv; + uint8_t bpll_pdiv; + uint8_t bpll_sdiv; + uint8_t use_bpll; /* 1 to use BPLL for cdrex, 0 to use MPLL */ + uint8_t pclk_cdrex_ratio; + unsigned int direct_cmd_msr[MEM_TIMINGS_MSR_COUNT]; + + unsigned int timing_ref; + unsigned int timing_row; + unsigned int timing_data; + unsigned int timing_power; + + /* DQS, DQ, DEBUG offsets */ + unsigned int phy0_dqs; + unsigned int phy1_dqs; + unsigned int phy0_dq; + unsigned int phy1_dq; + uint8_t phy0_tFS; + uint8_t phy1_tFS; + uint8_t phy0_pulld_dqs; + uint8_t phy1_pulld_dqs; + + uint8_t lpddr3_ctrl_phy_reset; + uint8_t ctrl_start_point; + uint8_t ctrl_inc; + uint8_t ctrl_start; + uint8_t ctrl_dll_on; + uint8_t ctrl_ref; + + uint8_t ctrl_force; + uint8_t ctrl_rdlat; + uint8_t ctrl_bstlen; + + uint8_t fp_resync; + uint8_t iv_size; + uint8_t dfi_init_start; + uint8_t aref_en; + + uint8_t rd_fetch; + + uint8_t zq_mode_dds; + uint8_t zq_mode_term; + uint8_t zq_mode_noterm; /* 1 to allow termination disable */ + + unsigned int memcontrol; + unsigned int memconfig; + + unsigned int membaseconfig0; + unsigned int membaseconfig1; + unsigned int prechconfig_tp_cnt; + unsigned int dpwrdn_cyc; + unsigned int dsref_cyc; + unsigned int concontrol; + /* Channel and Chip Selection */ + uint8_t dmc_channels; /* number of memory channels */ + uint8_t chips_per_channel; /* number of chips per channel */ + uint8_t chips_to_configure; /* number of chips to configure */ + uint8_t send_zq_init; /* 1 to send this command */ + unsigned int impedance; /* drive strength impedeance */ + uint8_t gate_leveling_enable; /* check gate leveling is enabled */ +}; + +/** + * Get the correct memory timings for our selected memory type and speed. + * + * @return pointer to the memory timings that we should use + */ +struct mem_timings *get_mem_timings(void); + #endif #endif |