summaryrefslogtreecommitdiff
path: root/src/drivers/parade/ps8625/ps8625.c
diff options
context:
space:
mode:
Diffstat (limited to 'src/drivers/parade/ps8625/ps8625.c')
-rw-r--r--src/drivers/parade/ps8625/ps8625.c134
1 files changed, 5 insertions, 129 deletions
diff --git a/src/drivers/parade/ps8625/ps8625.c b/src/drivers/parade/ps8625/ps8625.c
index 6cbe3b71d6..05219b0333 100644
--- a/src/drivers/parade/ps8625/ps8625.c
+++ b/src/drivers/parade/ps8625/ps8625.c
@@ -17,143 +17,19 @@
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#include "ps8625.h"
-
#include <device/i2c.h>
#include <stdint.h>
#include <stdlib.h>
-struct parade_write {
- uint8_t offset;
- uint8_t reg;
- uint8_t val;
-};
-
-static const struct parade_write parade_writes[] = {
- { 0x02, 0xa1, 0x01 }, /* HPD low */
- /*
- * SW setting
- * [1:0] SW output 1.2V voltage is lower to 96%
- */
- { 0x04, 0x14, 0x01 },
- /*
- * RCO SS setting
- * [5:4] = b01 0.5%, b10 1%, b11 1.5%
- */
- { 0x04, 0xe3, 0x20 },
- { 0x04, 0xe2, 0x80 }, /* [7] RCO SS enable */
- /*
- * RPHY Setting
- * [3:2] CDR tune wait cycle before
- * measure for fine tune b00: 1us,
- * 01: 0.5us, 10:2us, 11:4us.
- */
- { 0x04, 0x8a, 0x0c },
- { 0x04, 0x89, 0x08 }, /* [3] RFD always on */
- /*
- * CTN lock in/out:
- * 20000ppm/80000ppm. Lock out 2
- * times.
- */
- { 0x04, 0x71, 0x2d },
- /*
- * 2.7G CDR settings
- * NOF=40LSB for HBR CDR setting
- */
- { 0x04, 0x7d, 0x07 },
- { 0x04, 0x7b, 0x00 }, /* [1:0] Fmin=+4bands */
- { 0x04, 0x7a, 0xfd }, /* [7:5] DCO_FTRNG=+-40% */
- /*
- * 1.62G CDR settings
- * [5:2]NOF=64LSB [1:0]DCO scale is 2/5
- */
- { 0x04, 0xc0, 0x12 },
- { 0x04, 0xc1, 0x92 }, /* Gitune=-37% */
- { 0x04, 0xc2, 0x1c }, /* Fbstep=100% */
- { 0x04, 0x32, 0x80 }, /* [7] LOS signal disable */
- /*
- * RPIO Setting
- * [7:4] LVDS driver bias current :
- * 75% (250mV swing)
- */
- { 0x04, 0x00, 0xb0 },
- /*
- * [7:6] Right-bar GPIO output strength is 8mA
- */
- { 0x04, 0x15, 0x40 },
- /* EQ Training State Machine Setting */
- { 0x04, 0x54, 0x10 }, /* RCO calibration start */
- /* [4:0] MAX_LANE_COUNT set to one lane */
- { 0x01, 0x02, 0x81 },
- /* [4:0] LANE_COUNT_SET set to one lane */
- { 0x01, 0x21, 0x81 },
- { 0x00, 0x52, 0x20 },
- { 0x00, 0xf1, 0x03 }, /* HPD CP toggle enable */
- { 0x00, 0x62, 0x41 },
- /* Counter number, add 1ms counter delay */
- { 0x00, 0xf6, 0x01 },
- /*
- * [6]PWM function control by
- * DPCD0040f[7], default is PWM
- * block always works.
- */
- { 0x00, 0x77, 0x06 },
- /*
- * 04h Adjust VTotal tolerance to
- * fix the 30Hz no display issue
- */
- { 0x00, 0x4c, 0x04 },
- /* DPCD00400='h00, Parade OUI = 'h001cf8 */
- { 0x01, 0xc0, 0x00 },
- { 0x01, 0xc1, 0x1c }, /* DPCD00401='h1c */
- { 0x01, 0xc2, 0xf8 }, /* DPCD00402='hf8 */
- /*
- * DPCD403~408 = ASCII code
- * D2SLV5='h4432534c5635
- */
- { 0x01, 0xc3, 0x44 },
- { 0x01, 0xc4, 0x32 }, /* DPCD404 */
- { 0x01, 0xc5, 0x53 }, /* DPCD405 */
- { 0x01, 0xc6, 0x4c }, /* DPCD406 */
- { 0x01, 0xc7, 0x56 }, /* DPCD407 */
- { 0x01, 0xc8, 0x35 }, /* DPCD408 */
- /*
- * DPCD40A, Initial Code major revision
- * '01'
- */
- { 0x01, 0xca, 0x01 },
- /* DPCD40B, Initial Code minor revision '05' */
- { 0x01, 0xcb, 0x05 },
- /* DPCD720, Select internal PWM */
- { 0x01, 0xa5, 0xa0 },
- /*
- * FFh for 100% PWM of brightness, 0h for 0%
- * brightness
- */
- { 0x01, 0xa7, 0xff },
- /*
- * Set LVDS output as 6bit-VESA mapping,
- * single LVDS channel
- */
- { 0x01, 0xcc, 0x13 },
- /* Enable SSC set by register */
- { 0x02, 0xb1, 0x20 },
- /*
- * Set SSC enabled and +/-1% central
- * spreading
- */
- { 0x04, 0x10, 0x16 },
- /* MPU Clock source: LC => RCO */
- { 0x04, 0x59, 0x60 },
- { 0x04, 0x54, 0x14 }, /* LC -> RCO */
- { 0x02, 0xa1, 0x91 } /* HPD high */
-};
+#include "ps8625.h"
-void parade_ps8625_bridge_setup(unsigned bus, unsigned chip_base)
+void parade_ps8625_bridge_setup(unsigned bus, unsigned chip_base,
+ const struct parade_write *parade_writes,
+ int parade_write_count)
{
int i;
- for (i = 0; i < ARRAY_SIZE(parade_writes); i++) {
+ for (i = 0; i < parade_write_count; i++) {
const struct parade_write *w = &parade_writes[i];
i2c_write(bus, chip_base + w->offset, w->reg, sizeof(w->reg),
&w->val, sizeof(w->val));