diff options
Diffstat (limited to 'src/drivers/uart/uart8250reg.h')
| -rw-r--r-- | src/drivers/uart/uart8250reg.h | 108 |
1 files changed, 108 insertions, 0 deletions
diff --git a/src/drivers/uart/uart8250reg.h b/src/drivers/uart/uart8250reg.h new file mode 100644 index 0000000000..cdfbb1bc20 --- /dev/null +++ b/src/drivers/uart/uart8250reg.h @@ -0,0 +1,108 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2003 Eric Biederman + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef UART8250REG_H +#define UART8250REG_H + +/* Data */ +#define UART_RBR 0x00 +#define UART_TBR 0x00 + +/* Control */ +#define UART_IER 0x01 +#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ +#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ +#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ +#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ + +#define UART_IIR 0x02 +#define UART_IIR_NO_INT 0x01 /* No interrupts pending */ +#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ + +#define UART_IIR_MSI 0x00 /* Modem status interrupt */ +#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ +#define UART_IIR_RDI 0x04 /* Receiver data interrupt */ +#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ + +#define UART_FCR 0x02 +#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */ +#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ +#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ +#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ +#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ +#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ +#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ +#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ +#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ + +#define UART_FCR_RXSR 0x02 /* Receiver soft reset */ +#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */ + +#define UART_LCR 0x03 +#define UART_LCR_WLS_MSK 0x03 /* character length select mask */ +#define UART_LCR_WLS_5 0x00 /* 5 bit character length */ +#define UART_LCR_WLS_6 0x01 /* 6 bit character length */ +#define UART_LCR_WLS_7 0x02 /* 7 bit character length */ +#define UART_LCR_WLS_8 0x03 /* 8 bit character length */ +#define UART_LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */ +#define UART_LCR_PEN 0x08 /* Parity enable */ +#define UART_LCR_EPS 0x10 /* Even Parity Select */ +#define UART_LCR_STKP 0x20 /* Stick Parity */ +#define UART_LCR_SBRK 0x40 /* Set Break */ +#define UART_LCR_BKSE 0x80 /* Bank select enable */ +#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ + +#define UART_MCR 0x04 +#define UART_MCR_DTR 0x01 /* DTR */ +#define UART_MCR_RTS 0x02 /* RTS */ +#define UART_MCR_OUT1 0x04 /* Out 1 */ +#define UART_MCR_OUT2 0x08 /* Out 2 */ +#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ + +#define UART_MCR_DMA_EN 0x04 +#define UART_MCR_TX_DFR 0x08 + +#define UART_DLL 0x00 +#define UART_DLM 0x01 + +/* Status */ +#define UART_LSR 0x05 +#define UART_LSR_DR 0x01 /* Data ready */ +#define UART_LSR_OE 0x02 /* Overrun */ +#define UART_LSR_PE 0x04 /* Parity error */ +#define UART_LSR_FE 0x08 /* Framing error */ +#define UART_LSR_BI 0x10 /* Break */ +#define UART_LSR_THRE 0x20 /* Xmit holding register empty */ +#define UART_LSR_TEMT 0x40 /* Xmitter empty */ +#define UART_LSR_ERR 0x80 /* Error */ + +#define UART_MSR 0x06 +#define UART_MSR_DCD 0x80 /* Data Carrier Detect */ +#define UART_MSR_RI 0x40 /* Ring Indicator */ +#define UART_MSR_DSR 0x20 /* Data Set Ready */ +#define UART_MSR_CTS 0x10 /* Clear to Send */ +#define UART_MSR_DDCD 0x08 /* Delta DCD */ +#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ +#define UART_MSR_DDSR 0x02 /* Delta DSR */ +#define UART_MSR_DCTS 0x01 /* Delta CTS */ + +#define UART_SCR 0x07 +#define UART_SPR 0x07 + +#endif /* UART8250REG_H */ |