summaryrefslogtreecommitdiff
path: root/src/mainboard/Iwill/DK8S2/Config.lb
diff options
context:
space:
mode:
Diffstat (limited to 'src/mainboard/Iwill/DK8S2/Config.lb')
-rw-r--r--src/mainboard/Iwill/DK8S2/Config.lb162
1 files changed, 22 insertions, 140 deletions
diff --git a/src/mainboard/Iwill/DK8S2/Config.lb b/src/mainboard/Iwill/DK8S2/Config.lb
index 47400f8559..c28b8d3ca7 100644
--- a/src/mainboard/Iwill/DK8S2/Config.lb
+++ b/src/mainboard/Iwill/DK8S2/Config.lb
@@ -1,110 +1,3 @@
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HARD_RESET_BUS
-uses HARD_RESET_DEVICE
-uses HARD_RESET_FUNCTION
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
-uses CONFIG_MAX_CPUS
-uses CONFIG_IOAPIC
-uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
-uses CONFIG_ROM_STREAM
-uses CONFIG_ROM_STREAM_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE=524288
-
-###
-### Build options
-###
-
-##
-## Build code for the fallback boot
-##
-default HAVE_FALLBACK_BOOT=1
-
-##
-## Build code to reset the motherboard from linuxBIOS
-##
-default HAVE_HARD_RESET=1
-
-default HARD_RESET_BUS=1
-default HARD_RESET_DEVICE=4
-default HARD_RESET_FUNCTION=0
-
-##
-## Build code to export a programmable irq routing table
-##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
-
-##
-## Build code to export an x86 MP table
-## Useful for specifying IRQ routing values
-##
-default HAVE_MP_TABLE=1
-
-##
-## Build code to export a CMOS option table
-##
-default HAVE_OPTION_TABLE=1
-
-##
-## Build code for SMP support
-## Only worry about 2 micro processors
-##
-default CONFIG_SMP=1
-default CONFIG_MAX_CPUS=2
-
-##
-## Build code to setup a generic IOAPIC
-##
-default CONFIG_IOAPIC=1
-
-##
-## Clean up the motherboard id strings
-##
-#default MAINBOARD_PART_NUMBER="HDAMA"
-#default MAINBOARD_VENDOR="ARIMA"
-
-###
-### LinuxBIOS layout values
-###
-
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
-default ROM_IMAGE_SIZE = 65536
-
-##
-## Use a small 8K stack
-##
-default STACK_SIZE=0x2000
-
-##
-## Use a small 16K heap
-##
-default HEAP_SIZE=0x4000
-
-##
-## Only use the option table in a normal image
-##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-
##
## Compute the location and size of where this firmware image
## (linuxBIOS plus bootloader) will live in the boot rom chip.
@@ -123,7 +16,6 @@ end
##
default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
-default CONFIG_ROM_STREAM = 1
##
## Compute where this copy of linuxBIOS will start in the boot rom
@@ -145,15 +37,12 @@ default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
##
arch i386 end
-#cpu k8 end
##
## Build the objects we have code for in this directory.
##
-#object mainboard.o
driver mainboard.o
-#object static_devices.o
if HAVE_MP_TABLE object mptable.o end
if HAVE_PIRQ_TABLE object irq_tables.o end
@@ -164,41 +53,41 @@ dir /drivers/ati/ragexl
## Romcc output
##
makerule ./failover.E
- depends "$(MAINBOARD)/failover.c"
- action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E"
+ depends "$(MAINBOARD)/failover.c ./romcc"
+ action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
end
makerule ./failover.inc
- depends "./failover.E ./romcc"
- action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"
+ depends "$(MAINBOARD)/failover.c ./romcc"
+ action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
end
makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h"
- action "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
+ depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ action "./romcc -E -mcpu=k8 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
end
makerule ./auto.inc
- depends "./auto.E ./romcc"
- action "./romcc -mcpu=k8 -O2 ./auto.E > auto.inc"
+ depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
+ action "./romcc -mcpu=k8 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
end
##
## Build our 16 bit and 32 bit linuxBIOS entry code
##
-mainboardinit cpu/i386/entry16.inc
-mainboardinit cpu/i386/entry32.inc
-ldscript /cpu/i386/entry16.lds
-ldscript /cpu/i386/entry32.lds
+mainboardinit cpu/x86/16bit/entry16.inc
+mainboardinit cpu/x86/32bit/entry32.inc
+ldscript /cpu/x86/16bit/entry16.lds
+ldscript /cpu/x86/32bit/entry32.lds
##
## Build our reset vector (This is where linuxBIOS is entered)
##
if USE_FALLBACK_IMAGE
- mainboardinit cpu/i386/reset16.inc
- ldscript /cpu/i386/reset16.lds
+ mainboardinit cpu/x86/16bit/reset16.inc
+ ldscript /cpu/x86/16bit/reset16.lds
else
- mainboardinit cpu/i386/reset32.inc
- ldscript /cpu/i386/reset32.lds
+ mainboardinit cpu/x86/32bit/reset32.inc
+ ldscript /cpu/x86/32bit/reset32.lds
end
### Should this be in the northbridge code?
@@ -210,11 +99,6 @@ mainboardinit arch/i386/lib/cpu_reset.inc
mainboardinit arch/i386/lib/id.inc
ldscript /arch/i386/lib/id.lds
-##
-## Setup our mtrrs
-##
-mainboardinit cpu/k8/earlymtrr.inc
-
###
### This is the early phase of linuxBIOS startup
### Things are delicate and we test to see if we should
@@ -232,9 +116,12 @@ end
##
## Setup RAM
##
-mainboardinit cpu/k8/enable_mmx_sse.inc
+mainboardinit cpu/x86/fpu/enable_fpu.inc
+mainboardinit cpu/x86/mmx/enable_mmx.inc
+mainboardinit cpu/x86/sse/enable_sse.inc
mainboardinit ./auto.inc
-mainboardinit cpu/k8/disable_mmx_sse.inc
+mainboardinit cpu/x86/sse/disable_sse.inc
+mainboardinit cpu/x86/mmx/disable_mmx.inc
##
## Include the secondary Configuration files
@@ -242,6 +129,7 @@ mainboardinit cpu/k8/disable_mmx_sse.inc
dir /pc80
config chip.h
+# config for arima/hdama
chip northbridge/amd/amdk8
device pci_domain 0 on
device pci 18.0 on # LDT 0
@@ -330,9 +218,3 @@ chip northbridge/amd/amdk8
end
end
-##
-## Include the old serial code for those few places that still need it.
-##
-mainboardinit pc80/serial.inc
-mainboardinit arch/i386/lib/console.inc
-