diff options
Diffstat (limited to 'src/mainboard/Iwill/DK8X/Config.lb')
| -rw-r--r-- | src/mainboard/Iwill/DK8X/Config.lb | 300 |
1 files changed, 300 insertions, 0 deletions
diff --git a/src/mainboard/Iwill/DK8X/Config.lb b/src/mainboard/Iwill/DK8X/Config.lb new file mode 100644 index 0000000000..cc57d6397b --- /dev/null +++ b/src/mainboard/Iwill/DK8X/Config.lb @@ -0,0 +1,300 @@ +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses IRQ_SLOT_COUNT +uses HAVE_OPTION_TABLE +uses CONFIG_MAX_CPUS +uses CONFIG_IOAPIC +uses CONFIG_SMP +uses FALLBACK_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_STREAM +uses CONFIG_ROM_STREAM_START +uses PAYLOAD_SIZE +uses _ROMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses STACK_SIZE +uses HEAP_SIZE +uses USE_OPTION_TABLE + +## ROM_SIZE is the size of boot ROM that this board will use. +default ROM_SIZE=524288 + +### +### Build options +### + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=1 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=1 +default IRQ_SLOT_COUNT=9 + +## +## Build code to export an x86 MP table +## Useful for specifying IRQ routing values +## +default HAVE_MP_TABLE=1 + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=1 + +## +## Build code for SMP support +## Only worry about 2 micro processors +## +default CONFIG_SMP=1 +default CONFIG_MAX_CPUS=2 + +## +## Build code to setup a generic IOAPIC +## +default CONFIG_IOAPIC=1 + +## +## Clean up the motherboard id strings +## +#default MAINBOARD_PART_NUMBER="HDAMA" +#default MAINBOARD_VENDOR="ARIMA" + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 65536 + +## +## Use a small 8K stack +## +default STACK_SIZE=0x2000 + +## +## Use a small 16K heap +## +default HEAP_SIZE=0x4000 + +## +## Only use the option table in a normal image +## +default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE + +## +## Compute the location and size of where this firmware image +## (linuxBIOS plus bootloader) will live in the boot rom chip. +## +if USE_FALLBACK_IMAGE + default ROM_SECTION_SIZE = FALLBACK_SIZE + default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) +else + default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) + default ROM_SECTION_OFFSET = 0 +end + +## +## Compute the start location and size size of +## The linuxBIOS bootloader. +## +default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) +default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) +default CONFIG_ROM_STREAM = 1 + +## +## Compute where this copy of linuxBIOS will start in the boot rom +## +default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE ) + +## +## Compute a range of ROM that can cached to speed up linuxBIOS, +## execution speed. +## +## XIP_ROM_SIZE must be a power of 2. +## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE +## +default XIP_ROM_SIZE=65536 +default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) + +## +## Set all of the defaults for an x86 architecture +## + +arch i386 end +#cpu k8 end + +## +## Build the objects we have code for in this directory. +## + +#object mainboard.o +driver mainboard.o +#object static_devices.o +if HAVE_MP_TABLE object mptable.o end +if HAVE_PIRQ_TABLE object irq_tables.o end +object reset.o + +## +## Romcc output +## +makerule ./failover.E + depends "$(MAINBOARD)/failover.c" + action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E" +end + +makerule ./failover.inc + depends "./failover.E ./romcc" + action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E" +end + +makerule ./auto.E + depends "$(MAINBOARD)/auto.c" + action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E" +end +makerule ./auto.inc + depends "./auto.E ./romcc" + action "./romcc -mcpu=k8 -O2 ./auto.E > auto.inc" +end + +## +## Build our 16 bit and 32 bit linuxBIOS entry code +## +mainboardinit cpu/i386/entry16.inc +mainboardinit cpu/i386/entry32.inc +ldscript /cpu/i386/entry16.lds +ldscript /cpu/i386/entry32.lds + +## +## Build our reset vector (This is where linuxBIOS is entered) +## +if USE_FALLBACK_IMAGE + mainboardinit cpu/i386/reset16.inc + ldscript /cpu/i386/reset16.lds +else + mainboardinit cpu/i386/reset32.inc + ldscript /cpu/i386/reset32.lds +end + +### Should this be in the northbridge code? +mainboardinit arch/i386/lib/cpu_reset.inc + +## +## Include an id string (For safe flashing) +## +mainboardinit arch/i386/lib/id.inc +ldscript /arch/i386/lib/id.lds + +## +## Setup our mtrrs +## +mainboardinit cpu/k8/earlymtrr.inc + +### +### This is the early phase of linuxBIOS startup +### Things are delicate and we test to see if we should +### failover to another image. +### +if USE_FALLBACK_IMAGE + ldscript /arch/i386/lib/failover.lds + mainboardinit ./failover.inc +end + +### +### O.k. We aren't just an intermediary anymore! +### + +## +## Setup RAM +## +mainboardinit cpu/k8/enable_mmx_sse.inc +mainboardinit ./auto.inc +mainboardinit cpu/k8/disable_mmx_sse.inc + +## +## Include the secondary Configuration files +## +dir /pc80 +config chip.h + +northbridge amd/amdk8 "mc0" + pci 0:18.0 + pci 0:18.0 + pci 0:18.0 + pci 0:18.1 + pci 0:18.2 + pci 0:18.3 + southbridge amd/amd8131 "amd8131" link 0 + pci 0:0.0 + pci 0:0.1 + pci 0:1.0 + pci 0:1.1 + end + southbridge amd/amd8111 "amd8111" link 0 + pci 0:0.0 + pci 0:1.0 on + pci 0:1.1 on + pci 0:1.2 on + pci 0:1.3 on + pci 0:1.5 off + pci 0:1.6 off + pci 1:0.0 on + pci 1:0.1 on + pci 1:0.2 on + pci 1:1.0 off + superio winbond/w83627thf link 1 + pnp 2e.0 + pnp 2e.1 + pnp 2e.2 + pnp 2e.3 + pnp 2e.4 + pnp 2e.5 + pnp 2e.6 + pnp 2e.7 + pnp 2e.8 + pnp 2e.9 + pnp 2e.a + register "com1" = "{1, 0, 0x3f8, 4}" + register "lpt" = "{1}" + end + end +end + +northbridge amd/amdk8 "mc1" + pci 0:19.0 + pci 0:19.0 + pci 0:19.0 + pci 0:19.1 + pci 0:19.2 + pci 0:19.3 +end + +cpu k8 "cpu0" + register "up" = "{ .chip = &amd8131, .ht_width=16, .ht_speed=600 }" +end + +cpu k8 "cpu1" +end + +## +## Include the old serial code for those few places that still need it. +## +mainboardinit pc80/serial.inc +mainboardinit arch/i386/lib/console.inc + |