diff options
Diffstat (limited to 'src/mainboard/Iwill/DK8X')
| -rw-r--r-- | src/mainboard/Iwill/DK8X/Config.lb | 161 | ||||
| -rw-r--r-- | src/mainboard/Iwill/DK8X/auto.c | 138 | ||||
| -rw-r--r-- | src/mainboard/Iwill/DK8X/chip.h | 4 | ||||
| -rw-r--r-- | src/mainboard/Iwill/DK8X/cmos.layout | 29 | ||||
| -rw-r--r-- | src/mainboard/Iwill/DK8X/mainboard.c | 7 | ||||
| -rw-r--r-- | src/mainboard/Iwill/DK8X/mptable.c | 30 |
6 files changed, 127 insertions, 242 deletions
diff --git a/src/mainboard/Iwill/DK8X/Config.lb b/src/mainboard/Iwill/DK8X/Config.lb index f95725ecbb..903f5c6c62 100644 --- a/src/mainboard/Iwill/DK8X/Config.lb +++ b/src/mainboard/Iwill/DK8X/Config.lb @@ -1,110 +1,3 @@ -uses HAVE_MP_TABLE -uses HAVE_PIRQ_TABLE -uses USE_FALLBACK_IMAGE -uses HAVE_FALLBACK_BOOT -uses HAVE_HARD_RESET -uses HARD_RESET_BUS -uses HARD_RESET_DEVICE -uses HARD_RESET_FUNCTION -uses IRQ_SLOT_COUNT -uses HAVE_OPTION_TABLE -uses CONFIG_MAX_CPUS -uses CONFIG_IOAPIC -uses CONFIG_SMP -uses FALLBACK_SIZE -uses ROM_SIZE -uses ROM_SECTION_SIZE -uses ROM_IMAGE_SIZE -uses ROM_SECTION_SIZE -uses ROM_SECTION_OFFSET -uses CONFIG_ROM_STREAM -uses CONFIG_ROM_STREAM_START -uses PAYLOAD_SIZE -uses _ROMBASE -uses XIP_ROM_SIZE -uses XIP_ROM_BASE -uses STACK_SIZE -uses HEAP_SIZE -uses USE_OPTION_TABLE - -## ROM_SIZE is the size of boot ROM that this board will use. -default ROM_SIZE=524288 - -### -### Build options -### - -## -## Build code for the fallback boot -## -default HAVE_FALLBACK_BOOT=1 - -## -## Build code to reset the motherboard from linuxBIOS -## -default HAVE_HARD_RESET=1 - -default HARD_RESET_BUS=1 -default HARD_RESET_DEVICE=4 -default HARD_RESET_FUNCTION=0 - -## -## Build code to export a programmable irq routing table -## -default HAVE_PIRQ_TABLE=1 -default IRQ_SLOT_COUNT=9 - -## -## Build code to export an x86 MP table -## Useful for specifying IRQ routing values -## -default HAVE_MP_TABLE=1 - -## -## Build code to export a CMOS option table -## -default HAVE_OPTION_TABLE=1 - -## -## Build code for SMP support -## Only worry about 2 micro processors -## -default CONFIG_SMP=1 -default CONFIG_MAX_CPUS=2 - -## -## Build code to setup a generic IOAPIC -## -default CONFIG_IOAPIC=1 - -## -## Clean up the motherboard id strings -## -#default MAINBOARD_PART_NUMBER="HDAMA" -#default MAINBOARD_VENDOR="ARIMA" - -### -### LinuxBIOS layout values -### - -## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. -default ROM_IMAGE_SIZE = 65536 - -## -## Use a small 8K stack -## -default STACK_SIZE=0x2000 - -## -## Use a small 16K heap -## -default HEAP_SIZE=0x4000 - -## -## Only use the option table in a normal image -## -default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE - ## ## Compute the location and size of where this firmware image ## (linuxBIOS plus bootloader) will live in the boot rom chip. @@ -123,7 +16,6 @@ end ## default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) default CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) -default CONFIG_ROM_STREAM = 1 ## ## Compute where this copy of linuxBIOS will start in the boot rom @@ -145,15 +37,12 @@ default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) ## arch i386 end -#cpu k8 end ## ## Build the objects we have code for in this directory. ## -#object mainboard.o driver mainboard.o -#object static_devices.o if HAVE_MP_TABLE object mptable.o end if HAVE_PIRQ_TABLE object irq_tables.o end @@ -161,41 +50,41 @@ if HAVE_PIRQ_TABLE object irq_tables.o end ## Romcc output ## makerule ./failover.E - depends "$(MAINBOARD)/failover.c" - action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E" + depends "$(MAINBOARD)/failover.c ./romcc" + action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" end makerule ./failover.inc - depends "./failover.E ./romcc" - action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E" + depends "$(MAINBOARD)/failover.c ./romcc" + action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@" end makerule ./auto.E - depends "$(MAINBOARD)/auto.c" - action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E" + depends "$(MAINBOARD)/auto.c option_table.h ./romcc" + action "./romcc -E -mcpu=k8 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" end makerule ./auto.inc - depends "./auto.E ./romcc" - action "./romcc -mcpu=k8 -O2 ./auto.E > auto.inc" + depends "$(MAINBOARD)/auto.c option_table.h ./romcc" + action "./romcc -mcpu=k8 -O2 -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@" end ## ## Build our 16 bit and 32 bit linuxBIOS entry code ## -mainboardinit cpu/i386/entry16.inc -mainboardinit cpu/i386/entry32.inc -ldscript /cpu/i386/entry16.lds -ldscript /cpu/i386/entry32.lds +mainboardinit cpu/x86/16bit/entry16.inc +mainboardinit cpu/x86/32bit/entry32.inc +ldscript /cpu/x86/16bit/entry16.lds +ldscript /cpu/x86/32bit/entry32.lds ## ## Build our reset vector (This is where linuxBIOS is entered) ## if USE_FALLBACK_IMAGE - mainboardinit cpu/i386/reset16.inc - ldscript /cpu/i386/reset16.lds + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds else - mainboardinit cpu/i386/reset32.inc - ldscript /cpu/i386/reset32.lds + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds end ### Should this be in the northbridge code? @@ -207,11 +96,6 @@ mainboardinit arch/i386/lib/cpu_reset.inc mainboardinit arch/i386/lib/id.inc ldscript /arch/i386/lib/id.lds -## -## Setup our mtrrs -## -mainboardinit cpu/k8/earlymtrr.inc - ### ### This is the early phase of linuxBIOS startup ### Things are delicate and we test to see if we should @@ -229,9 +113,12 @@ end ## ## Setup RAM ## -mainboardinit cpu/k8/enable_mmx_sse.inc +mainboardinit cpu/x86/fpu/enable_fpu.inc +mainboardinit cpu/x86/mmx/enable_mmx.inc +mainboardinit cpu/x86/sse/enable_sse.inc mainboardinit ./auto.inc -mainboardinit cpu/k8/disable_mmx_sse.inc +mainboardinit cpu/x86/sse/disable_sse.inc +mainboardinit cpu/x86/mmx/disable_mmx.inc ## ## Include the secondary Configuration files @@ -306,9 +193,3 @@ chip northbridge/amd/amdk8 end end -## -## Include the old serial code for those few places that still need it. -## -mainboardinit pc80/serial.inc -mainboardinit arch/i386/lib/console.inc - diff --git a/src/mainboard/Iwill/DK8X/auto.c b/src/mainboard/Iwill/DK8X/auto.c index 9889f23229..b8ca3c82ba 100644 --- a/src/mainboard/Iwill/DK8X/auto.c +++ b/src/mainboard/Iwill/DK8X/auto.c @@ -1,25 +1,51 @@ #define ASSEMBLY 1 #include <stdint.h> #include <device/pci_def.h> -#include <cpu/p6/apic.h> #include <arch/io.h> -#include <device/pnp.h> +#include <device/pnp_def.h> #include <arch/romcc_io.h> +#include <cpu/x86/lapic.h> +#include <arch/cpu.h> +#include "option_table.h" +#include "pc80/mc146818rtc_early.c" #include "pc80/serial.c" #include "arch/i386/lib/console.c" #include "ram/ramtest.c" -#include "northbridge/amd/amdk8/early_ht.c" +#include "northbridge/amd/amdk8/incoherent_ht.c" #include "southbridge/amd/amd8111/amd8111_early_smbus.c" #include "northbridge/amd/amdk8/raminit.h" -#include "cpu/k8/apic_timer.c" +#include "cpu/amd/model_fxx/apic_timer.c" #include "lib/delay.c" -#include "cpu/p6/boot_cpu.c" +#include "cpu/x86/lapic/boot_cpu.c" #include "northbridge/amd/amdk8/reset_test.c" #include "northbridge/amd/amdk8/debug.c" #include "northbridge/amd/amdk8/cpu_rev.c" +#include "superio/NSC/pc87360/pc87360_early_serial.c" +#include "cpu/amd/mtrr/amd_earlymtrr.c" +#include "cpu/x86/bist.h" -#define SIO_BASE 0x2e +#define SERIAL_DEV PNP_DEV(0x2e, PC87360_SP1) +static void hard_reset(void) +{ + set_bios_reset(); + + /* enable cf9 */ + pci_write_config8(PCI_DEV(0, 0x04, 3), 0x41, 0xf1); + /* reset */ + outb(0x0e, 0x0cf9); +} + +static void soft_reset(void) +{ + set_bios_reset(); + pci_write_config8(PCI_DEV(0, 0x04, 0), 0x47, 1); +} + +/* + * GPIO28 of 8111 will control H0_MEMRESET_L + * GPIO29 of 8111 will control H1_MEMRESET_L + */ static void memreset_setup(void) { if (is_cpu_pre_c0()) { @@ -103,68 +129,11 @@ static inline int spd_read_byte(unsigned device, unsigned address) #include "sdram/generic_sdram.c" #include "northbridge/amd/amdk8/resourcemap.c" -static void enable_lapic(void) -{ - - msr_t msr; - msr = rdmsr(0x1b); - msr.hi &= 0xffffff00; - msr.lo &= 0x000007ff; - msr.lo |= APIC_DEFAULT_BASE | (1 << 11); - wrmsr(0x1b, msr); -} - -static void stop_this_cpu(void) -{ - unsigned apicid; - apicid = apic_read(APIC_ID) >> 24; - - /* Send an APIC INIT to myself */ - apic_write(APIC_ICR2, SET_APIC_DEST_FIELD(apicid)); - apic_write(APIC_ICR, APIC_INT_LEVELTRIG | APIC_INT_ASSERT | APIC_DM_INIT); - /* Wait for the ipi send to finish */ - apic_wait_icr_idle(); - - /* Deassert the APIC INIT */ - apic_write(APIC_ICR2, SET_APIC_DEST_FIELD(apicid)); - apic_write(APIC_ICR, APIC_INT_LEVELTRIG | APIC_DM_INIT); - /* Wait for the ipi send to finish */ - apic_wait_icr_idle(); - - /* If I haven't halted spin forever */ - for(;;) { - hlt(); - } -} - -#define PC87360_FDC 0x00 -#define PC87360_PP 0x01 -#define PC87360_SP2 0x02 -#define PC87360_SP1 0x03 -#define PC87360_SWC 0x04 -#define PC87360_KBCM 0x05 -#define PC87360_KBCK 0x06 -#define PC87360_GPIO 0x07 -#define PC87360_ACB 0x08 -#define PC87360_FSCM 0x09 -#define PC87360_WDT 0x0A - -static void pc87360_enable_serial(void) -{ - pnp_set_logical_device(SIO_BASE, PC87360_SP1); - pnp_set_enable(SIO_BASE, 1); - pnp_set_iobase0(SIO_BASE, 0x3f8); -} - #define FIRST_CPU 1 #define SECOND_CPU 1 #define TOTAL_CPUS (FIRST_CPU + SECOND_CPU) -static void main(void) +static void main(unsigned long bist) { - /* - * GPIO28 of 8111 will control H0_MEMRESET_L - * GPIO29 of 8111 will control H1_MEMRESET_L - */ static const struct mem_controller cpu[] = { #if FIRST_CPU { @@ -189,22 +158,38 @@ static void main(void) }, #endif }; - if (cpu_init_detected()) { - asm("jmp __cpu_reset"); - } - enable_lapic(); - init_timer(); - if (!boot_cpu()) { - stop_this_cpu(); + + int needs_reset; + if (bist == 0) { + /* Skip this if there was a built in self test failure */ + amd_early_mtrr_init(); + enable_lapic(); + init_timer(); + /* Has this cpu already booted? */ + if (cpu_init_detected()) { + asm volatile ("jmp __cpu_reset"); + } + distinguish_cpu_resets(); + if (!boot_cpu()) { + stop_this_cpu(); + } } - pc87360_enable_serial(); + /* Setup the console */ + pc87360_enable_serial(SERIAL_DEV, TTYS0_BASE); uart_init(); console_init(); + + /* Halt if there was a built in self test failure */ + report_bist_failure(bist); + setup_default_resource_map(); - setup_coherent_ht_domain(); - enumerate_ht_chain(0); - distinguish_cpu_resets(0); - + needs_reset = setup_coherent_ht_domain(); + needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0x80); + if (needs_reset) { + print_info("ht reset -\r\n"); + soft_reset(); + } + #if 0 print_pci_devices(); #endif @@ -212,6 +197,7 @@ static void main(void) #if 0 dump_spd_registers(&cpu[0]); #endif + memreset_setup(); sdram_initialize(sizeof(cpu)/sizeof(cpu[0]), cpu); diff --git a/src/mainboard/Iwill/DK8X/chip.h b/src/mainboard/Iwill/DK8X/chip.h index c0f74846ef..7710024cca 100644 --- a/src/mainboard/Iwill/DK8X/chip.h +++ b/src/mainboard/Iwill/DK8X/chip.h @@ -1,5 +1,5 @@ -extern struct chip_operations mainboard_arima_hdama_control; +extern struct chip_operations mainboard_Iwill_DK8X_ops; -struct mainboard_arima_hdama_config { +struct mainboard_Iwill_DK8X_config { int nothing; }; diff --git a/src/mainboard/Iwill/DK8X/cmos.layout b/src/mainboard/Iwill/DK8X/cmos.layout index 5ba4c032c1..1ab6187288 100644 --- a/src/mainboard/Iwill/DK8X/cmos.layout +++ b/src/mainboard/Iwill/DK8X/cmos.layout @@ -29,6 +29,9 @@ entries 386 1 e 1 ECC_memory 388 4 r 0 reboot_bits 392 3 e 5 baud_rate +395 1 e 1 hw_scrubber +396 1 e 1 interleave_chip_selects +397 2 e 8 max_mem_clock 400 1 e 1 power_on_after_fail 412 4 e 6 debug_level 416 4 e 7 boot_first @@ -36,7 +39,15 @@ entries 424 4 e 7 boot_third 428 4 h 0 boot_index 432 8 h 0 boot_countdown -1008 16 h 0 check_sum +440 4 e 9 slow_cpu +444 1 e 1 nmi +445 1 e 1 iommu +728 256 h 0 user_data +984 16 h 0 check_sum +# Reserve the extended AMD configuration registers +1000 24 r 0 reserved_memory + + enumerations @@ -66,9 +77,19 @@ enumerations 7 9 Fallback_HDD 7 10 Fallback_Floppy #7 3 ROM +8 0 200Mhz +8 1 166Mhz +8 2 133Mhz +8 3 100Mhz +9 0 off +9 1 87.5% +9 2 75.0% +9 3 62.5% +9 4 50.0% +9 5 37.5% +9 6 25.0% +9 7 12.5% checksums -checksum 392 1007 1008 - - +checksum 392 983 984 diff --git a/src/mainboard/Iwill/DK8X/mainboard.c b/src/mainboard/Iwill/DK8X/mainboard.c index 845285c881..a1b05d0943 100644 --- a/src/mainboard/Iwill/DK8X/mainboard.c +++ b/src/mainboard/Iwill/DK8X/mainboard.c @@ -3,12 +3,9 @@ #include <device/pci.h> #include <device/pci_ids.h> #include <device/pci_ops.h> - -#include <arch/io.h> -#include "../../../northbridge/amd/amdk8/northbridge.h" #include "chip.h" -struct chip_operations mainboard_arima_hdama_control = { - .name = "Arima HDAMA mainboard ", +struct chip_operations mainboard_Iwill_DK8X_ops = { + CHIP_NAME("Iwill DK8X mainboard") }; diff --git a/src/mainboard/Iwill/DK8X/mptable.c b/src/mainboard/Iwill/DK8X/mptable.c index bd9df2e3ac..34e6037c21 100644 --- a/src/mainboard/Iwill/DK8X/mptable.c +++ b/src/mainboard/Iwill/DK8X/mptable.c @@ -4,11 +4,11 @@ #include <string.h> #include <stdint.h> -void *smp_write_config_table(void *v, unsigned long * processor_map) +void *smp_write_config_table(void *v) { static const char sig[4] = "PCMP"; - static const char oem[8] = "LNXI "; - static const char productid[12] = "HDAMA "; + static const char oem[8] = "IWILL "; + static const char productid[12] = "DK8X "; struct mp_config_table *mc; unsigned char bus_num; unsigned char bus_isa; @@ -33,7 +33,7 @@ void *smp_write_config_table(void *v, unsigned long * processor_map) mc->mpe_checksum = 0; mc->reserved = 0; - smp_write_processors(mc, processor_map); + smp_write_processors(mc); { device_t dev; @@ -82,24 +82,25 @@ void *smp_write_config_table(void *v, unsigned long * processor_map) smp_write_bus(mc, bus_isa, "ISA "); /* IOAPIC handling */ - smp_write_ioapic(mc, 2, 0x11, 0xfec00000); { device_t dev; - uint32_t base; + struct resource *res; /* 8131 apic 3 */ dev = dev_find_slot(1, PCI_DEVFN(0x01,1)); if (dev) { - base = pci_read_config32(dev, PCI_BASE_ADDRESS_0); - base &= PCI_BASE_ADDRESS_MEM_MASK; - smp_write_ioapic(mc, 0x03, 0x11, base); + res = find_resource(dev, PCI_BASE_ADDRESS_0); + if (res) { + smp_write_ioapic(mc, 0x03, 0x11, res->base); + } } /* 8131 apic 4 */ dev = dev_find_slot(1, PCI_DEVFN(0x02,1)); if (dev) { - base = pci_read_config32(dev, PCI_BASE_ADDRESS_0); - base &= PCI_BASE_ADDRESS_MEM_MASK; - smp_write_ioapic(mc, 0x04, 0x11, base); + res = find_resource(dev, PCI_BASE_ADDRESS_0); + if (res) { + smp_write_ioapic(mc, 0x04, 0x11, res->base); + } } } @@ -216,17 +217,16 @@ void *smp_write_config_table(void *v, unsigned long * processor_map) /* Compute the checksums */ mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length); - mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length); printk_debug("Wrote the mp table end at: %p - %p\n", mc, smp_next_mpe_entry(mc)); return smp_next_mpe_entry(mc); } -unsigned long write_smp_table(unsigned long addr, unsigned long *processor_map) +unsigned long write_smp_table(unsigned long addr) { void *v; v = smp_write_floating_table(addr); - return (unsigned long)smp_write_config_table(v, processor_map); + return (unsigned long)smp_write_config_table(v); } |