summaryrefslogtreecommitdiff
path: root/src/mainboard/artecgroup
diff options
context:
space:
mode:
Diffstat (limited to 'src/mainboard/artecgroup')
-rw-r--r--src/mainboard/artecgroup/dbe61/Config.lb128
-rw-r--r--src/mainboard/artecgroup/dbe61/Options.lb19
-rw-r--r--src/mainboard/artecgroup/dbe61/auto.c134
-rw-r--r--src/mainboard/artecgroup/dbe61/cache_as_ram_auto.c215
-rw-r--r--src/mainboard/artecgroup/dbe61/irq_tables.c141
-rw-r--r--src/mainboard/artecgroup/dbe61/mainboard.c30
-rw-r--r--src/mainboard/artecgroup/dbe61/spd_table.h53
7 files changed, 446 insertions, 274 deletions
diff --git a/src/mainboard/artecgroup/dbe61/Config.lb b/src/mainboard/artecgroup/dbe61/Config.lb
index 97975e7c36..40f157f6e9 100644
--- a/src/mainboard/artecgroup/dbe61/Config.lb
+++ b/src/mainboard/artecgroup/dbe61/Config.lb
@@ -47,27 +47,17 @@ driver mainboard.o
if HAVE_PIRQ_TABLE object irq_tables.o end
#object reset.o
-##
-## Romcc output
-##
-makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ./romcc"
- action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
-end
-makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ./romcc"
- action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+if USE_DCACHE_RAM
+ #compile cache_as_ram.c to auto.inc
+ makerule ./cache_as_ram_auto.inc
+ depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@"
+ action "perl -e 's/.rodata/.rom.data/g' -pi $@"
+ action "perl -e 's/.text/.section .rom.text/g' -pi $@"
+ end
end
-makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
- action "./romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
-end
-makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
- action "./romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
-end
##
## Build our 16 bit and 32 bit linuxBIOS entry code
@@ -104,7 +94,7 @@ ldscript /arch/i386/lib/id.lds
###
if USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
- mainboardinit ./failover.inc
+# mainboardinit ./failover.inc
end
###
@@ -115,7 +105,11 @@ end
## Setup RAM
##
mainboardinit cpu/x86/fpu/enable_fpu.inc
-mainboardinit ./auto.inc
+
+if USE_DCACHE_RAM
+ mainboardinit cpu/amd/model_lx/cache_as_ram.inc
+ mainboardinit ./cache_as_ram_auto.inc
+end
##
## Include the secondary Configuration files
@@ -124,70 +118,44 @@ dir /pc80
config chip.h
chip northbridge/amd/lx
- register "irqmap" = "0xcba5"
+ device pci_domain 0 on
+ device pci 1.0 on end # Northbridge
+ device pci 1.1 on end # Graphics
+ chip southbridge/amd/cs5536
+ # IRQ 12 and 1 unmasked, Keyboard and Mouse IRQs. OK
+ # SIRQ Mode = Active(Quiet) mode. Save power....
+ # Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse IRQs. OK
+ register "lpc_serirq_enable" = "0x00001002"
+ register "lpc_serirq_polarity" = "0x0000EFFD"
+ register "lpc_serirq_mode" = "1"
+ register "enable_gpio_int_route" = "0x0D0C0700"
+ register "enable_ide_nand_flash" = "0" # 0:ide mode, 1:flash
+ register "enable_USBP4_device" = "0" #0: host, 1:device
+ register "enable_USBP4_overcurrent" = "0" #0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381)
+ register "com1_enable" = "0"
+ register "com1_address" = "0x2F8"
+ register "com1_irq" = "3"
+ register "com2_enable" = "1"
+ register "com2_address" = "0x3F8"
+ register "com2_irq" = "4"
+ register "unwanted_vpci[0]" = "0" # End of list has a zero
+ device pci b.0 on end # Slot 3
+ device pci c.0 on end # Slot 4
+ device pci d.0 on end # Slot 1
+ device pci e.0 on end # Slot 2
+ device pci f.0 on end # ISA Bridge
+ device pci f.2 on end # IDE Controller
+ device pci f.3 on end # Audio
+ device pci f.4 on end # OHCI
+ device pci f.5 on end # EHCI
+ end
+ end
+ # APIC cluster is late CPU init.
device apic_cluster 0 on
chip cpu/amd/model_lx
device apic 0 on end
end
end
- device pci_domain 0 on
-
- device pci 1.0 on end # Host Bridge
-
-# chip drivers/pci/realmode
-# device pci 1.1 on end # VGA
-# register "rom_address" = "0xfffc0000" # at the beginning of 256k
-# end
-
- device pci 1.2 off end # AES
- chip southbridge/amd/cs5536_lx
- register "enable_ide_nand_flash" = "0"
-
- register "isa_irq" = "0"
- #register "flash_irq" = "14"
-
- ## IDE IRQ
- register "enable_ide_irq" = "0"
-
- register "audio_irq" = "5"
- register "usb_irq" = "7"
-
- register "uart0_irq" = "0"
- register "uart1_irq" = "4"
-
- ## PCI INTA ... INTD and their GPIO pins
- ## int==0: disable
- register "pci_int[0]" = "0"
- register "pci_int[1]" = "10"
- register "pci_int[2]" = "0"
- register "pci_int[3]" = "0"
- register "pci_int_pin[0]" = "0"
- register "pci_int_pin[1]" = "7"
- register "pci_int_pin[2]" = "0"
- register "pci_int_pin[3]" = "0"
-
-
- # Keyboard Emulation Logic IRQs
- # Enable keyboard IRQ2
- register "enable_kel_keyb_irq" = "0"
- # Enable mouse IRQ12
- register "enable_kel_mouse_irq" = "0"
- # Configure KEL Emulation IRQ, 0 to disable
- register "kel_emul_irq" = "0"
-
- device pci f.0 on end # ISA Bridge
- device pci f.1 on end # Flash controller
- device pci f.2 off end # IDE controller
- device pci f.3 on end # Audio
- device pci f.4 on end # OHCI
- device pci f.5 on end # EHCI
- device pci f.6 off end # UDC controller
- device pci f.7 off end # OTG controller
- end
-# chip drivers/pci/rtl8139
-## device pci d.0 on end # Realtek LAN
-# register "nic_irq" = "10"
-# end
- end
+
end
diff --git a/src/mainboard/artecgroup/dbe61/Options.lb b/src/mainboard/artecgroup/dbe61/Options.lb
index 382f3bdda7..3f773af79c 100644
--- a/src/mainboard/artecgroup/dbe61/Options.lb
+++ b/src/mainboard/artecgroup/dbe61/Options.lb
@@ -23,6 +23,7 @@ uses ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
+uses CONFIG_PRECOMPRESSED_PAYLOAD
uses PAYLOAD_SIZE
uses _ROMBASE
uses _RAMBASE
@@ -44,6 +45,9 @@ uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
+uses USE_DCACHE_RAM
+uses DCACHE_RAM_BASE
+uses DCACHE_RAM_SIZE
## ROM_SIZE is the size of boot ROM that this board will use.
default ROM_SIZE = 256*1024
@@ -51,8 +55,8 @@ default ROM_SIZE = 256*1024
###
### Build options
###
-default CONFIG_CONSOLE_VGA=1
-default CONFIG_PCI_ROM_RUN=1
+default CONFIG_CONSOLE_VGA=0
+default CONFIG_PCI_ROM_RUN=0
default CONFIG_VIDEO_MB=8
##
@@ -78,8 +82,8 @@ default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=0
-default IRQ_SLOT_COUNT=6
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=3
#object irq_tables.o
@@ -97,6 +101,13 @@ default ROM_IMAGE_SIZE = 65536
default FALLBACK_SIZE = 131072
##
+## enable CACHE_AS_RAM specifics
+##
+default USE_DCACHE_RAM=1
+default DCACHE_RAM_BASE=0xc8000
+default DCACHE_RAM_SIZE=0x08000
+
+##
## Use a small 8K stack
##
default STACK_SIZE=0x2000
diff --git a/src/mainboard/artecgroup/dbe61/auto.c b/src/mainboard/artecgroup/dbe61/auto.c
deleted file mode 100644
index 1dba629381..0000000000
--- a/src/mainboard/artecgroup/dbe61/auto.c
+++ /dev/null
@@ -1,134 +0,0 @@
-#define ASSEMBLY 1
-
-#include <stdint.h>
-#include <device/pci_def.h>
-#include <arch/io.h>
-#include <device/pnp_def.h>
-#include <arch/romcc_io.h>
-#include <arch/hlt.h>
-#include "pc80/serial.c"
-#include "arch/i386/lib/console.c"
-#include "ram/ramtest.c"
-//#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
-#include "cpu/x86/bist.h"
-#include "cpu/x86/msr.h"
-#include <cpu/amd/lxdef.h>
-
-//#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
-
-#include "southbridge/amd/cs5536/cs5536_early_smbus.c"
-#include "southbridge/amd/cs5536/cs5536_early_setup.c"
-
-static inline int spd_read_byte(unsigned device, unsigned address)
-{
- return smbus_read_byte(device, address);
-}
-
-#include "northbridge/amd/lx/raminit.h"
-
-static inline unsigned int fls(unsigned int x)
-{
- int r;
-
- __asm__("bsfl %1,%0\n\t"
- "jnz 1f\n\t"
- "movl $32,%0\n"
- "1:" : "=r" (r) : "g" (x));
- return r;
-}
-
-static void sdram_set_spd_registers(const struct mem_controller *ctrl)
-{
- /* Total size of DIMM = 2^row address (byte 3) * 2^col address (byte 4) *
- * component Banks (byte 17) * module banks, side (byte 5) *
- * width in bits (byte 6,7)
- * = Density per side (byte 31) * number of sides (byte 5) */
- /* 1. Initialize GLMC registers base on SPD values, do one DIMM for now */
- msr_t msr;
- unsigned char module_banks, val;
-
- msr.hi = 0x10075012;
- msr.lo = 0x00000040;
-
- wrmsr(MC_CF07_DATA, msr); //GX3
-
- /* timing and mode ... */
-
- //msr = rdmsr(0x20000019);
-
- /* per standard bios settings */
-/*
- msr.hi = 0x18000108;
- msr.lo =
- (6<<28) | // cas_lat
- (10<<24)| // ref2act
- (7<<20)| // act2pre
- (3<<16)| // pre2act
- (3<<12)| // act2cmd
- (2<<8)| // act2act
- (2<<6)| // dplwr
- (2<<4)| // dplrd
- (3); // dal
- * the msr value reported by quanta is very, very different.
- * we will go with that value for now.
- *
- //msr.lo = 0x286332a3;
-*/
- //wrmsr(0x20000019, msr); //GX3
-
-}
-
-#include "northbridge/amd/lx/raminit.c"
-#include "sdram/generic_sdram.c"
-
-/* CPU and GLIU mult/div */
-#define PLLMSRhi 0x0000039C
-/* Hold Count - how long we will sit in reset */
-#define PLLMSRlo 0x00DE0000
-
-#include "northbridge/amd/lx/pll_reset.c"
-#include "cpu/amd/model_lx/cpureginit.c"
-#include "cpu/amd/model_lx/syspreinit.c"
-
-static void msr_init(void)
-{
- __builtin_wrmsr(0x10000020, 0xfff80, 0x20000000);
- __builtin_wrmsr(0x10000021, 0x80fffe0, 0x20000000);
-
- __builtin_wrmsr(0x40000020, 0xfff80, 0x20000000);
- __builtin_wrmsr(0x40000021, 0x80fffe0, 0x20000000);
-}
-
-
-static void main(unsigned long bist)
-{
- static const struct mem_controller memctrl [] = {
- {.channel0 = {(0xa<<3)|0, (0xa<<3)|1}}
- };
-
- SystemPreInit(); //GX3 OK
-
- msr_init(); //GX3 OK
-
- cs5536_early_setup(); //GX3 OK
-
- /* NOTE: must do this AFTER the early_setup!
- * it is counting on some early MSR setup
- * for cs5536
- */
- cs5536_setup_onchipuart(); //GX3 OK
-
- uart_init(); //GX3 OK
- console_init(); //GX3 OK
-
- pll_reset(); //GX3 OK
-
- cpuRegInit(); //GX3 OK
-
- print_err("done cpuRegInit\n");
-
- sdram_initialize(1, memctrl); //GX3 OK almost
-
- /* Check all of memory */
- //ram_check(0x00000000, 640*1024);
-}
diff --git a/src/mainboard/artecgroup/dbe61/cache_as_ram_auto.c b/src/mainboard/artecgroup/dbe61/cache_as_ram_auto.c
new file mode 100644
index 0000000000..e0b51b1770
--- /dev/null
+++ b/src/mainboard/artecgroup/dbe61/cache_as_ram_auto.c
@@ -0,0 +1,215 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define ASSEMBLY 1
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/hlt.h>
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "cpu/x86/bist.h"
+#include "cpu/x86/msr.h"
+#include <cpu/amd/lxdef.h>
+#include <cpu/amd/geode_post_code.h>
+#include "southbridge/amd/cs5536/cs5536.h"
+#include "spd_table.h"
+
+
+#define POST_CODE(x) outb(x, 0x80)
+
+#include "southbridge/amd/cs5536/cs5536_early_smbus.c"
+#include "southbridge/amd/cs5536/cs5536_early_setup.c"
+
+#define DIMM0 0xA0
+#define DIMM1 0xA2
+
+
+static int spd_read_byte(unsigned device, unsigned address)
+{
+ int i;
+
+ if (device == DIMM0){
+ for (i=0; i < (sizeof spd_table/sizeof spd_table[0]); i++){
+ if (spd_table[i].address == address){
+ return spd_table[i].data;
+ }
+ }
+ }
+
+ /* returns 0xFF on any failures */
+ return 0xFF;
+}
+
+#define ManualConf 0 /* Do automatic strapped PLL config */
+/* CPU and GLIU mult/div 500/266*/
+#define PLLMSRhi 0x0000039C /* 33MHz PCI, 0x000003DD for 66MHz PCI */
+/* Hold Count - how long we will sit in reset */
+#define PLLMSRlo 0x00DE6000
+
+#include "northbridge/amd/lx/raminit.h"
+#include "northbridge/amd/lx/pll_reset.c"
+#include "northbridge/amd/lx/raminit.c"
+#include "sdram/generic_sdram.c"
+#include "cpu/amd/model_lx/cpureginit.c"
+#include "cpu/amd/model_lx/syspreinit.c"
+
+static void msr_init(void)
+{
+ msr_t msr;
+ /* Setup access to the cache for under 1MB. */
+ msr.hi = 0x24fffc02;
+ msr.lo = 0x1000A000; /* 0-A0000 write back */
+ wrmsr(CPU_RCONF_DEFAULT, msr);
+
+ msr.hi = 0x0; /* write back */
+ msr.lo = 0x0;
+ wrmsr(CPU_RCONF_A0_BF, msr);
+ wrmsr(CPU_RCONF_C0_DF, msr);
+ wrmsr(CPU_RCONF_E0_FF, msr);
+
+ /* Setup access to the cache for under 640K. Note MC not setup yet. */
+ msr.hi = 0x20000000;
+ msr.lo = 0xfff80;
+ wrmsr(MSR_GLIU0 + 0x20, msr);
+
+ msr.hi = 0x20000000;
+ msr.lo = 0x80fffe0;
+ wrmsr(MSR_GLIU0 + 0x21, msr);
+
+ msr.hi = 0x20000000;
+ msr.lo = 0xfff80;
+ wrmsr(MSR_GLIU1 + 0x20, msr);
+
+ msr.hi = 0x20000000;
+ msr.lo = 0x80fffe0;
+ wrmsr(MSR_GLIU1 + 0x21, msr);
+
+}
+
+static void mb_gpio_init(void)
+{
+ /* Early mainboard specific GPIO setup */
+}
+
+static void cs5536_setup_onchipuart2(void)
+{
+ msr_t msr;
+
+ /* GPIO4 - UART2_TX */
+ /* Set: Output Enable (0x4) */
+ outl(GPIOL_4_SET, GPIO_IO_BASE + GPIOL_OUTPUT_ENABLE);
+ /* Set: OUTAUX1 Select (0x10) */
+ outl(GPIOL_4_SET, GPIO_IO_BASE + GPIOL_OUT_AUX1_SELECT);
+ /* GPIO4 - UART2_RX */
+ /* Set: Input Enable (0x20) */
+ outl(GPIOL_3_SET, GPIO_IO_BASE + GPIOL_INPUT_ENABLE);
+ /* Set: INAUX1 Select (0x34) */
+ outl(GPIOL_3_SET, GPIO_IO_BASE + GPIOL_IN_AUX1_SELECT);
+
+ /* Set: GPIO 3 + 3 Pull Up (0x18) */
+ outl(GPIOL_3_SET | GPIOL_4_SET, GPIO_IO_BASE + GPIOL_PULLUP_ENABLE);
+
+ /* set address to 3F8 */
+ msr = rdmsr(MDD_LEG_IO);
+ msr.lo |= 0x7 << 20;
+ wrmsr(MDD_LEG_IO, msr);
+
+ /* Bit 1 = DEVEN (device enable)
+ * Bit 4 = EN_BANKS (allow access to the upper banks
+ */
+ msr.lo = (1 << 4) | (1 << 1);
+ msr.hi = 0;
+
+ /* enable COM2 */
+ wrmsr(MDD_UART2_CONF, msr);
+}
+
+void cache_as_ram_main(void)
+{
+ POST_CODE(0x01);
+
+ static const struct mem_controller memctrl[] = {
+ {.channel0 = {(0xa << 3) | 0, (0xa << 3) | 1}}
+ };
+
+ SystemPreInit();
+ msr_init();
+
+ cs5536_early_setup();
+
+ /* NOTE: must do this AFTER the early_setup!
+ * it is counting on some early MSR setup
+ * for cs5536
+ */
+ /* cs5536_disable_internal_uart disable them. Set them up now... */
+ cs5536_setup_onchipuart2(); /* dbe61 uses UART2 as COM1 */
+ mb_gpio_init();
+ uart_init();
+ console_init();
+
+ pll_reset(ManualConf);
+
+ cpuRegInit();
+
+ sdram_initialize(1, memctrl);
+
+ /* Dump memory configuratation */
+ /*{
+ msr_t msr;
+ msr = rdmsr(MC_CF07_DATA);
+ print_debug("MC_CF07_DATA: ");
+ print_debug_hex32(MC_CF07_DATA);
+ print_debug(" value is: ");
+ print_debug_hex32(msr.hi);
+ print_debug(":");
+ print_debug_hex32(msr.lo);
+ print_debug(" \n");
+
+ msr = rdmsr(MC_CF1017_DATA);
+ print_debug("MC_CF1017_DATA: ");
+ print_debug_hex32(MC_CF1017_DATA);
+ print_debug(" value is: ");
+ print_debug_hex32(msr.hi);
+ print_debug(":");
+ print_debug_hex32(msr.lo);
+ print_debug(" \n");
+
+ msr = rdmsr(MC_CF8F_DATA);
+ print_debug("MC_CF8F_DATA: ");
+ print_debug_hex32(MC_CF8F_DATA);
+ print_debug(" value is: ");
+ print_debug_hex32(msr.hi);
+ print_debug(":");
+ print_debug_hex32(msr.lo);
+ msr = rdmsr(MC_CF8F_DATA);
+ print_debug(" \n");
+ }*/
+
+ /* Check memory. */
+ /* ram_check(0x00000000, 640 * 1024); */
+
+ /* Memory is setup. Return to cache_as_ram.inc and continue to boot */
+ return;
+}
diff --git a/src/mainboard/artecgroup/dbe61/irq_tables.c b/src/mainboard/artecgroup/dbe61/irq_tables.c
index 4322e20e9b..07ded9d386 100644
--- a/src/mainboard/artecgroup/dbe61/irq_tables.c
+++ b/src/mainboard/artecgroup/dbe61/irq_tables.c
@@ -1,60 +1,105 @@
-/* This file was generated by getpir.c, do not modify!
- (but if you do, please run checkpir on it to verify)
- * Contains the IRQ Routing Table dumped directly from your memory, which BIOS sets up
+/*
+ * This file is part of the LinuxBIOS project.
*
- * Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
-*/
+ * Copyright (C) 2007 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
#include <arch/pirq_routing.h>
+#include <console/console.h>
+#include <arch/io.h>
+#include <arch/pirq_routing.h>
+#include "../../../southbridge/amd/cs5536/cs5536.h"
-#define ID_SLOT_PCI_NET 1 // ThinCan ethernet
-#define ID_SLOT_PCI_RSVD1 2 // reserved entry 1
-#define ID_SLOT_PCI_RSVD3 3 // reserved entry 2
-#define ID_SLOT_PCI_RSVD2 4 // reserved entry 3
-#define ID_EMBED_PCI 0xff // onboard PCI device
+/* Platform IRQs */
+#define PIRQA 10
+#define PIRQB 11
+#define PIRQC 10
+#define PIRQD 11
-// CS5535 PCI INT[A-D] Interrupt Routing lines.
-#define NO_CONNECT 0 // not used
-#define CS_PCI_INTA 1 // PCI INTA
-#define CS_PCI_INTB 2 // PCI INTB
-#define CS_PCI_INTC 3 // PCI INTC
-#define CS_PCI_INTD 4 // PCI INTD
+/* Map */
+#define M_PIRQA (1 << PIRQA) /* Bitmap of supported IRQs */
+#define M_PIRQB (1 << PIRQB) /* Bitmap of supported IRQs */
+#define M_PIRQC (1 << PIRQC) /* Bitmap of supported IRQs */
+#define M_PIRQD (1 << PIRQD) /* Bitmap of supported IRQs */
-// IRQ bitmap reference line FEDCBA9876543210
-// 0000110000100000b
-#define PCI_IRQ 0xc20 // PCI allowed IRQs here
+/* Link */
+#define L_PIRQA 1 /* Means Slot INTx# Connects To Chipset INTA# */
+#define L_PIRQB 2 /* Means Slot INTx# Connects To Chipset INTB# */
+#define L_PIRQC 3 /* Means Slot INTx# Connects To Chipset INTC# */
+#define L_PIRQD 4 /* Means Slot INTx# Connects To Chipset INTD# */
-const struct irq_routing_table intel_irq_routing_table =
-{
- PIRQ_SIGNATURE, /* u32 signature */
- PIRQ_VERSION, /* u16 version */
- 32+16*6, /* there can be total 2 devices on the bus */
- 0x00, /* Where the interrupt router lies (bus) */
- (0x12<<3)|0x0, /* Where the interrupt router lies (dev) */
- 0x0800, /* IRQs devoted exclusively to PCI usage */
- 0x1022, /* Vendor */
- 0x208f, /* Device */
- 0x00000000, /* Crap (miniport) */
- { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
- 0xdf, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+const struct irq_routing_table intel_irq_routing_table = {
+ PIRQ_SIGNATURE, /* u32 signature */
+ PIRQ_VERSION, /* u16 version */
+ 32 + 16 * IRQ_SLOT_COUNT, /* there can be total 6 devices on the bus */
+ 0x00, /* Where the interrupt router lies (bus) */
+ (0x0F << 3) | 0x0, /* Where the interrupt router lies (dev) */
+ 0x00, /* IRQs devoted exclusively to PCI usage */
+ 0x100B, /* Vendor */
+ 0x002B, /* Device */
+ 0, /* Crap (miniport) */
+ {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, /* u8 rfu[11] */
+ 0x00, /* u8 checksum , this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
{
- /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
- // Geode GX3 Host Bridge and VGA Graphics
- {0, 0x01<<3, {{CS_PCI_INTA, PCI_IRQ}, {NO_CONNECT, PCI_IRQ}, {NO_CONNECT, PCI_IRQ}, {NO_CONNECT, PCI_IRQ}}, ID_EMBED_PCI, 0x0},
- // Realtek RTL8100/8139 Network Controller
- {0, 0x0d<<3, {{CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}, {CS_PCI_INTA, PCI_IRQ}}, ID_SLOT_PCI_NET, 0x0},
- // Reserved for future extensions
- {0, 0x0c<<3, {{CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}}, ID_SLOT_PCI_RSVD1, 0x0},
- // Geode CS5535/CS5536 IO Companion: USB controllers, IDE, Audio.
- {0, 0x0f<<3, {{CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}}, ID_EMBED_PCI, 0x0},
- // Reserved for future extensions
- {0, 0x0e<<3, {{CS_PCI_INTC, PCI_IRQ}, {CS_PCI_INTD, PCI_IRQ}, {CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}}, ID_SLOT_PCI_RSVD2, 0x0},
- // Reserved for future extensions
- {0, 0x0b<<3, {{CS_PCI_INTD, PCI_IRQ}, {CS_PCI_INTA, PCI_IRQ}, {CS_PCI_INTB, PCI_IRQ}, {CS_PCI_INTC, PCI_IRQ}}, ID_SLOT_PCI_RSVD3, 0x0}
- }
+ /* If you change the number of entries, change the IRQ_SLOT_COUNT above! */
+ /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
+ {0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* cpu */
+ {0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */
+ {0x00, (0x0D << 3) | 0x0, {{L_PIRQC, M_PIRQC}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* ethernet */
+ }
};
unsigned long write_pirq_routing_table(unsigned long addr)
{
- return copy_pirq_routing_table(addr);
-}
+ int i, j, k, num_entries;
+ unsigned char pirq[4];
+ uint16_t chipset_irq_map;
+ uint32_t pciAddr, pirtable_end;
+ struct irq_routing_table *pirq_tbl;
+
+ pirtable_end = copy_pirq_routing_table(addr);
+
+ /* Set up chipset IRQ steering. */
+ pciAddr = 0x80000000 | (CHIPSET_DEV_NUM << 11) | 0x5C;
+ chipset_irq_map = (PIRQD << 12 | PIRQC << 8 | PIRQB << 4 | PIRQA);
+ printk_debug("%s(%08X, %04X)\n", __FUNCTION__, pciAddr,
+ chipset_irq_map);
+ outl(pciAddr & ~3, 0xCF8);
+ outl(chipset_irq_map, 0xCFC);
+
+ pirq_tbl = (struct irq_routing_table *)(addr);
+ num_entries = (pirq_tbl->size - 32) / 16;
+
+ /* Set PCI IRQs. */
+ for (i = 0; i < num_entries; i++) {
+ printk_debug("PIR Entry %d Dev/Fn: %X Slot: %d\n", i,
+ pirq_tbl->slots[i].devfn, pirq_tbl->slots[i].slot);
+ for (j = 0; j < 4; j++) {
+ printk_debug("INT: %c bitmap: %x ", 'A' + j,
+ pirq_tbl->slots[i].irq[j].bitmap);
+ for (k = 0; (!((pirq_tbl->slots[i].irq[j].bitmap >> k) & 1)) && (pirq_tbl->slots[i].irq[j].bitmap != 0); k++) ; /* Finds lsb in bitmap to IRQ#. */
+ pirq[j] = k;
+ printk_debug("PIRQ: %d\n", k);
+ }
+
+ /* Bus, device, slots IRQs for {A,B,C,D}. */
+ pci_assign_irqs(pirq_tbl->slots[i].bus,
+ pirq_tbl->slots[i].devfn >> 3, pirq);
+ }
+
+ /* Put the PIR table in memory and checksum. */
+ return pirtable_end;
+} \ No newline at end of file
diff --git a/src/mainboard/artecgroup/dbe61/mainboard.c b/src/mainboard/artecgroup/dbe61/mainboard.c
index 0476400de0..ba60b53f64 100644
--- a/src/mainboard/artecgroup/dbe61/mainboard.c
+++ b/src/mainboard/artecgroup/dbe61/mainboard.c
@@ -1,3 +1,22 @@
+/*
+* This file is part of the LinuxBIOS project.
+*
+* Copyright (C) 2007 Advanced Micro Devices
+*
+* This program is free software; you can redistribute it and/or modify
+* it under the terms of the GNU General Public License version 2 as
+* published by the Free Software Foundation.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+* GNU General Public License for more details.
+*
+* You should have received a copy of the GNU General Public License
+* along with this program; if not, write to the Free Software
+* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+*/
+
#include <console/console.h>
#include <device/device.h>
#include <device/pci.h>
@@ -6,20 +25,15 @@
#include <arch/io.h>
#include <cpu/x86/msr.h>
#include <cpu/amd/lxdef.h>
+#include "../../../southbridge/amd/cs5536/cs5536.h"
#include "chip.h"
-#define DIVIL_LBAR_GPIO 0x5140000c
-
static void init_gpio()
{
msr_t msr;
- printk_debug("Initializing GPIO module...\n");
+ printk_debug("Checking GPIO module...\n");
- // initialize the GPIO LBAR
- msr.lo = GPIO_BASE;
- msr.hi = 0x0000f001;
- wrmsr(DIVIL_LBAR_GPIO, msr);
- msr = rdmsr(DIVIL_LBAR_GPIO);
+ msr = rdmsr(MDD_LBAR_GPIO);
printk_debug("DIVIL_LBAR_GPIO set to 0x%08x 0x%08x\n", msr.hi, msr.lo);
}
diff --git a/src/mainboard/artecgroup/dbe61/spd_table.h b/src/mainboard/artecgroup/dbe61/spd_table.h
new file mode 100644
index 0000000000..00b6e7da10
--- /dev/null
+++ b/src/mainboard/artecgroup/dbe61/spd_table.h
@@ -0,0 +1,53 @@
+/*
+ * This file is part of the LinuxBIOS project.
+ *
+ * Copyright (C) 2007 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <spd.h>
+
+struct spd_entry {
+ unsigned int address;
+ unsigned int data;
+ };
+
+/* Save space by using a short list of SPD values used by Geode LX Memory init */
+/* 128MB */
+const struct spd_entry spd_table [] =
+{
+{SPD_MEMORY_TYPE, 0x07}, /* (Fundamental) memory type */
+{SPD_NUM_ROWS, 0x0D}, /* Number of row address bits */
+{SPD_NUM_COLUMNS, 0x09}, /* Number of column address bits */
+{SPD_NUM_DIMM_BANKS, 0x01}, /* Number of module rows (banks) */
+{SPD_MIN_CYCLE_TIME_AT_CAS_MAX, 0x50}, /* SDRAM cycle time (highest CAS latency), RAS access time (tRAC) */
+{SPD_REFRESH, 0x82}, /* Refresh rate/type */
+{SPD_PRIMARY_SDRAM_WIDTH, 0x08}, /* SDRAM width (primary SDRAM) */
+{SPD_NUM_BANKS_PER_SDRAM, 0x04}, /* SDRAM device attributes, number of banks on SDRAM device */
+{SPD_ACCEPTABLE_CAS_LATENCIES, 0x1C}, /* SDRAM device attributes, CAS latency */
+{SPD_MODULE_ATTRIBUTES, 0x20}, /* SDRAM module attributes */
+{SPD_DEVICE_ATTRIBUTES_GENERAL, 0xC0}, /* SDRAM device attributes, general */
+{SPD_SDRAM_CYCLE_TIME_2ND, 0x60}, /* SDRAM cycle time (2nd highest CAS latency) */
+{SPD_SDRAM_CYCLE_TIME_3RD, 0x75}, /* SDRAM cycle time (3rd highest CAS latency) */
+{SPD_MIN_ROW_PRECHARGE_TIME, 0x3C}, /* Minimum row precharge time (Trp) */
+{SPD_MIN_ROWACTIVE_TO_ROWACTIVE, 0x28}, /* Minimum row active to row active (Trrd) */
+{SPD_MIN_RAS_TO_CAS_DELAY, 0x3C}, /* Minimum RAS to CAS delay (Trcd) */
+{SPD_MIN_ACTIVE_TO_PRECHARGE_DELAY, 0x28}, /* Minimum RAS pulse width (Tras) */
+{SPD_DENSITY_OF_EACH_ROW_ON_MODULE, 0x20}, /* Density of each row on module */
+{SPD_CMD_SIGNAL_INPUT_HOLD_TIME, 0x60}, /* Command and address signal input hold time */
+{SPD_tRC, 0x37}, /* SDRAM Device Minimum Active to Active/Auto Refresh Time (tRC) */
+{SPD_tRFC, 0x46} /* SDRAM Device Minimum Auto Refresh to Active/Auto Refresh (tRFC) */
+};