diff options
Diffstat (limited to 'src/mainboard/asus/a8v-e_se/Options.lb')
-rw-r--r-- | src/mainboard/asus/a8v-e_se/Options.lb | 313 |
1 files changed, 313 insertions, 0 deletions
diff --git a/src/mainboard/asus/a8v-e_se/Options.lb b/src/mainboard/asus/a8v-e_se/Options.lb new file mode 100644 index 0000000000..e6b8fbfe6b --- /dev/null +++ b/src/mainboard/asus/a8v-e_se/Options.lb @@ -0,0 +1,313 @@ +## +## This file is part of the LinuxBIOS project. +## +## Copyright (C) 2007 Rudolf Marek <r.marek@assembler.cz> +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License v2 as published by +## the Free Software Foundation. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +## + +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses IRQ_SLOT_COUNT +uses HAVE_OPTION_TABLE +uses CONFIG_MAX_CPUS +uses CONFIG_MAX_PHYSICAL_CPUS +uses CONFIG_LOGICAL_CPUS +uses CONFIG_IOAPIC +uses CONFIG_SMP +uses FALLBACK_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_PAYLOAD +uses CONFIG_ROM_PAYLOAD_START +uses PAYLOAD_SIZE +uses _ROMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses STACK_SIZE +uses HEAP_SIZE +##uses USE_OPTION_TABLE +##uses CONFIG_LB_MEM_TOPK + +uses HAVE_ACPI_TABLES + +uses LB_CKS_RANGE_START +uses LB_CKS_RANGE_END +uses LB_CKS_LOC +uses MAINBOARD +uses MAINBOARD_PART_NUMBER +uses MAINBOARD_VENDOR +uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID +uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID +uses LINUXBIOS_EXTRA_VERSION +uses _RAMBASE +uses CONFIG_GDB_STUB +uses CROSS_COMPILE +uses CC +uses HOSTCC +uses OBJCOPY +uses TTYS0_BAUD +uses TTYS0_BASE +uses TTYS0_LCS +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL +uses CONFIG_CONSOLE_SERIAL8250 +uses HAVE_INIT_TIMER +uses CONFIG_GDB_STUB +uses CONFIG_CHIP_NAME +uses CONFIG_CONSOLE_VGA +uses CONFIG_PCI_ROM_RUN +#bx_b001- uses K8_HW_MEM_HOLE_SIZEK +uses K8_HT_FREQ_1G_SUPPORT + +uses USE_DCACHE_RAM +uses DCACHE_RAM_BASE +uses DCACHE_RAM_SIZE +uses DCACHE_RAM_GLOBAL_VAR_SIZE +uses CONFIG_USE_INIT + +uses ENABLE_APIC_EXT_ID +uses APIC_ID_OFFSET +uses LIFT_BSP_APIC_ID + +uses HT_CHAIN_UNITID_BASE +uses HT_CHAIN_END_UNITID_BASE +#bx_b001- uses K8_SB_HT_CHAIN_ON_BUS0 +uses SB_HT_CHAIN_UNITID_OFFSET_ONLY +#bx_b005+ +uses SB_HT_CHAIN_ON_BUS0 + +## ROM_SIZE is the size of boot ROM that this board will use. +#512K bytes +default ROM_SIZE=512 * 1024 + +#1M bytes +#bx- default ROM_SIZE=1024 * 1024 + +## +## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use +## +#256K +default FALLBACK_SIZE=256 * 1024 + +### +### Build options +### + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=0 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=0 +default IRQ_SLOT_COUNT=11 + +## +## Build code to export an x86 MP table +## Useful for specifying IRQ routing values +## +default HAVE_MP_TABLE=1 + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=0 + +## +## Move the default LinuxBIOS cmos range off of AMD RTC registers +## +default LB_CKS_RANGE_START=49 +default LB_CKS_RANGE_END=122 +default LB_CKS_LOC=123 + +## +## Build code for SMP support +## Only worry about 2 micro processors +## +default CONFIG_SMP=1 +default CONFIG_MAX_CPUS=2 +default CONFIG_MAX_PHYSICAL_CPUS=1 +default CONFIG_LOGICAL_CPUS=1 + +#acpi +default HAVE_ACPI_TABLES=1 + +#CHIP_NAME ? +#default CONFIG_CHIP_NAME=1 + +#1G memory hole +#bx_b001- default K8_HW_MEM_HOLE_SIZEK=0x100000 + +#Opteron K8 1G HT Support +default K8_HT_FREQ_1G_SUPPORT=1 + +##HT Unit ID offset, default is 1, the typical one +default HT_CHAIN_UNITID_BASE=0x0 + +##real SB Unit ID, default is 0x20, mean dont touch it at last +#default HT_CHAIN_END_UNITID_BASE=0x0 + +#make the SB HT chain on bus 0, default is not (0) +#bx_b001- default K8_SB_HT_CHAIN_ON_BUS0=2 + +##bx_b005+ make the SB HT chain on bus 0 +default SB_HT_CHAIN_ON_BUS0=1 + +##only offset for SB chain?, default is yes(1) +default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0 + +#VGA +default CONFIG_CONSOLE_VGA=1 +default CONFIG_PCI_ROM_RUN=1 + +## +## enable CACHE_AS_RAM specifics +## +default USE_DCACHE_RAM=1 +default DCACHE_RAM_BASE=0xcc000 +default DCACHE_RAM_SIZE=0x4000 +default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000 +default CONFIG_USE_INIT=0 + +default ENABLE_APIC_EXT_ID=0 +default APIC_ID_OFFSET=0x10 +default LIFT_BSP_APIC_ID=0 + + +## +## Build code to setup a generic IOAPIC +## +default CONFIG_IOAPIC=1 + +## +## Clean up the motherboard id strings +## +default MAINBOARD_PART_NUMBER="A8V-E SE" +default MAINBOARD_VENDOR="ASUS" +default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1043 +#default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1234 + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 64 * 1024 + +## +## Use a small 8K stack +## +default STACK_SIZE= 8 * 1024 + +## +## Use a small 256K heap +## +default HEAP_SIZE=256 * 1024 + +#more 1M for pgtbl +##default CONFIG_LB_MEM_TOPK=2048 + +## +## Only use the option table in a normal image +## +##default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE + +## +## LinuxBIOS C code runs at this location in RAM +## +default _RAMBASE=0x00004000 + +## +## Load the payload from the ROM +## +default CONFIG_ROM_PAYLOAD = 1 + +### +### Defaults of options that you may want to override in the target config file +### + +## +## The default compiler +## +default CC="$(CROSS_COMPILE)gcc -m32" +default HOSTCC="gcc" + +## +## Disable the gdb stub by default +## +default CONFIG_GDB_STUB=0 + +## +## The Serial Console +## + +# To Enable the Serial Console +default CONFIG_CONSOLE_SERIAL8250=1 + +## Select the serial console baud rate +default TTYS0_BAUD=115200 +#default TTYS0_BAUD=57600 +#default TTYS0_BAUD=38400 +#default TTYS0_BAUD=19200 +#default TTYS0_BAUD=9600 +#default TTYS0_BAUD=4800 +#default TTYS0_BAUD=2400 +#default TTYS0_BAUD=1200 + +# Select the serial console base port +default TTYS0_BASE=0x3f8 + +# Select the serial protocol +# This defaults to 8 data bits, 1 stop bit, and no parity +default TTYS0_LCS=0x3 + +## +### Select the linuxBIOS loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +default DEFAULT_CONSOLE_LOGLEVEL=8 +## At a maximum only compile in this level of debugging +default MAXIMUM_CONSOLE_LOGLEVEL=8 + +## +## Select power on after power fail setting +default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" + +### End Options.lb +end |