diff options
Diffstat (limited to 'src/mainboard/asus/a8v-e_se')
| -rw-r--r-- | src/mainboard/asus/a8v-e_se/Config.lb | 378 | ||||
| -rw-r--r-- | src/mainboard/asus/a8v-e_se/Options.lb | 300 | ||||
| -rw-r--r-- | src/mainboard/asus/a8v-e_se/acpi_tables.c | 52 | ||||
| -rw-r--r-- | src/mainboard/asus/a8v-e_se/cache_as_ram_auto.c | 141 | ||||
| -rw-r--r-- | src/mainboard/asus/a8v-e_se/chip.h | 1 | ||||
| -rw-r--r-- | src/mainboard/asus/a8v-e_se/dsdt.asl | 366 | ||||
| -rw-r--r-- | src/mainboard/asus/a8v-e_se/fadt.c | 18 | ||||
| -rw-r--r-- | src/mainboard/asus/a8v-e_se/mainboard.c | 1 | ||||
| -rw-r--r-- | src/mainboard/asus/a8v-e_se/mptable.c | 60 |
9 files changed, 522 insertions, 795 deletions
diff --git a/src/mainboard/asus/a8v-e_se/Config.lb b/src/mainboard/asus/a8v-e_se/Config.lb index e8841adf6e..aa5ca70703 100644 --- a/src/mainboard/asus/a8v-e_se/Config.lb +++ b/src/mainboard/asus/a8v-e_se/Config.lb @@ -2,8 +2,7 @@ ## This file is part of the coreboot project. ## ## Copyright (C) 2007 AMD -## Written by Yinghai Lu <yinghailu@amd.com> for AMD. -## +## (Written by Yinghai Lu <yinghailu@amd.com> for AMD) ## Copyright (C) 2007 Rudolf Marek <r.marek@assembler.cz> ## ## This program is free software; you can redistribute it and/or modify @@ -21,260 +20,195 @@ ## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA ## -## -## Compute the location and size of where this firmware image -## (coreboot plus bootloader) will live in the boot rom chip. -## - if USE_FALLBACK_IMAGE - default ROM_SECTION_SIZE = FALLBACK_SIZE - default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) - else - default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) - default ROM_SECTION_OFFSET = 0 - end +if USE_FALLBACK_IMAGE + default ROM_SECTION_SIZE = FALLBACK_SIZE + default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE ) +else + default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE ) + default ROM_SECTION_OFFSET = 0 +end -## -## Compute the start location and size size of -## The coreboot bootloader. -## -default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) +default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE ) default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) -default CONFIG_ROM_PAYLOAD = 1 - -## -## Compute where this copy of coreboot will start in the boot rom -## -default _ROMBASE = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE ) - -## -## Compute a range of ROM that can cached to speed up coreboot, -## execution speed. -## -## XIP_ROM_SIZE must be a power of 2. -## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE -## -default XIP_ROM_SIZE=65536 -default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE ) +default CONFIG_ROM_PAYLOAD = 1 +default _ROMBASE = (CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE) +default XIP_ROM_SIZE = 65536 +default XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE) arch i386 end -## -## Build the objects we have code for in this directory. -## - driver mainboard.o - if HAVE_ACPI_TABLES - object acpi_tables.o - object fadt.o - makerule dsdt.c - depends "$(MAINBOARD)/dsdt.asl" - action "iasl -p $(PWD)/dsdt -tc $(MAINBOARD)/dsdt.asl" - action "mv dsdt.hex dsdt.c" - end - object ./dsdt.o + object acpi_tables.o + object fadt.o + makerule dsdt.c + depends "$(MAINBOARD)/dsdt.asl" + action "iasl -p $(PWD)/dsdt -tc $(MAINBOARD)/dsdt.asl" + action "mv dsdt.hex dsdt.c" + end + object ./dsdt.o end - if HAVE_MP_TABLE object mptable.o end if HAVE_PIRQ_TABLE object irq_tables.o end -#object reset.o -if USE_DCACHE_RAM - - if CONFIG_USE_INIT - makerule ./cache_as_ram_auto.o - depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" - action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o $@" - end - else - makerule ./cache_as_ram_auto.inc - depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" - action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@" - action "perl -e 's/.rodata/.rom.data/g' -pi $@" - action "perl -e 's/.text/.section .rom.text/g' -pi $@" - end - end +# object reset.o +if USE_DCACHE_RAM + if CONFIG_USE_INIT + makerule ./cache_as_ram_auto.o + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o $@" + end + else + makerule ./cache_as_ram_auto.inc + depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h" + action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@" + action "perl -e 's/.rodata/.rom.data/g' -pi $@" + action "perl -e 's/.text/.section .rom.text/g' -pi $@" + end + end end -## -## Build our 16 bit and 32 bit coreboot entry code -## - if USE_FALLBACK_IMAGE - mainboardinit cpu/x86/16bit/entry16.inc - ldscript /cpu/x86/16bit/entry16.lds - mainboardinit southbridge/via/k8t890/romstrap.inc - ldscript /southbridge/via/k8t890/romstrap.lds - + mainboardinit cpu/x86/16bit/entry16.inc + ldscript /cpu/x86/16bit/entry16.lds + mainboardinit southbridge/via/k8t890/romstrap.inc + ldscript /southbridge/via/k8t890/romstrap.lds end mainboardinit cpu/x86/32bit/entry32.inc if USE_DCACHE_RAM - if CONFIG_USE_INIT - ldscript /cpu/x86/32bit/entry32.lds - end - - if CONFIG_USE_INIT - ldscript /cpu/amd/car/cache_as_ram.lds - end + if CONFIG_USE_INIT + ldscript /cpu/x86/32bit/entry32.lds + end + if CONFIG_USE_INIT + ldscript /cpu/amd/car/cache_as_ram.lds + end end - -## -## Build our reset vector (This is where coreboot is entered) -## - -if USE_FALLBACK_IMAGE - mainboardinit cpu/x86/16bit/reset16.inc - ldscript /cpu/x86/16bit/reset16.lds +if USE_FALLBACK_IMAGE + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds else - mainboardinit cpu/x86/32bit/reset32.inc - ldscript /cpu/x86/32bit/reset32.lds + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds end if USE_DCACHE_RAM - ## - ## Setup Cache-As-Ram - ## - mainboardinit cpu/amd/car/cache_as_ram.inc + mainboardinit cpu/amd/car/cache_as_ram.inc end -### -### This is the early phase of coreboot startup -### Things are delicate and we test to see if we should -### failover to another image. -### - if USE_FALLBACK_IMAGE - if USE_DCACHE_RAM - ldscript /arch/i386/lib/failover.lds - end + if USE_DCACHE_RAM + ldscript /arch/i386/lib/failover.lds + end end - -## -## Setup RAM -## if USE_DCACHE_RAM - - if CONFIG_USE_INIT - initobject cache_as_ram_auto.o - else - mainboardinit ./cache_as_ram_auto.inc - end + if CONFIG_USE_INIT + initobject cache_as_ram_auto.o + else + mainboardinit ./cache_as_ram_auto.inc + end end -## -## Include the secondary Configuration files -## if CONFIG_CHIP_NAME - config chip.h + config chip.h end -chip northbridge/amd/amdk8/root_complex - device apic_cluster 0 on - chip cpu/amd/socket_939 - device apic 0 on end - end +chip northbridge/amd/amdk8/root_complex # Root complex + device apic_cluster 0 on # APIC cluster + chip cpu/amd/socket_939 # CPU + device apic 0 on end # APIC + end + end + device pci_domain 0 on # PCI domain + chip northbridge/amd/amdk8 # mc0 + device pci 18.0 on # Northbridge + # Devices on link 0, link 0 == LDT 0 + chip southbridge/via/vt8237r # Southbridge + register "ide0_enable" = "1" # Enable IDE channel 0 + register "ide1_enable" = "1" # Enable IDE channel 1 + register "ide0_80pin_cable" = "1" # 80pin cable on IDE channel 0 + register "ide1_80pin_cable" = "1" # 80pin cable on IDE channel 1 + register "fn_ctrl_lo" = "0" # Enable SB functions + register "fn_ctrl_hi" = "0xad" # Enable SB functions + device pci 0.0 on end # HT + device pci f.1 on end # IDE + device pci 11.0 on # LPC + chip drivers/generic/generic # DIMM 0-0-0 + device i2c 50 on end + end + chip drivers/generic/generic # DIMM 0-0-1 + device i2c 51 on end + end + chip drivers/generic/generic # DIMM 0-1-0 + device i2c 52 on end + end + chip drivers/generic/generic # DIMM 0-1-1 + device i2c 53 on end + end + chip superio/winbond/w83627ehg # Super I/O + device pnp 2e.0 on # Floppy + io 0x60 = 0x3f0 + irq 0x70 = 6 + drq 0x74 = 2 + end + device pnp 2e.1 on # Parallel port + io 0x60 = 0x378 + irq 0x70 = 7 + drq 0x74 = 3 + end + device pnp 2e.2 on # Com1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + device pnp 2e.3 off # Com2 (N/A on this board) + io 0x60 = 0x2f8 + irq 0x70 = 3 + end + device pnp 2e.5 off # PS/2 keyboard (off) + end + device pnp 2e.106 off # Serial flash + io 0x60 = 0x100 + end + device pnp 2e.007 off # GPIO 1 + end + device pnp 2e.107 on # Game port + io 0x60 = 0x201 + end + device pnp 2e.207 on # MIDI + io 0x62 = 0x330 + irq 0x70 = 0xa + end + device pnp 2e.307 off # GPIO 6 + end + device pnp 2e.8 off # WDTO_PLED + end + device pnp 2e.009 on # GPIO 2 on LDN 9 is in sio_setup + end + device pnp 2e.109 off # GPIO 3 + end + device pnp 2e.209 off # GPIO 4 + end + device pnp 2e.309 on # GPIO5 + end + device pnp 2e.a off # ACPI + end + device pnp 2e.b on # Hardware monitor + io 0x60 = 0x290 + irq 0x70 = 0 + end + end + end + device pci 12.0 off end # VIA LAN (off, other chip used) end - - device pci_domain 0 on - chip northbridge/amd/amdk8 #mc0 - device pci 18.0 on # northbridge - # devices on link 0, link 0 == LDT 0 - chip southbridge/via/vt8237r - #both IDE channels - register "ide0_enable" = "1" - register "ide1_enable" = "1" - #both cables are 80pin - register "ide0_80pin_cable" = "1" - register "ide1_80pin_cable" = "1" - #enables the functions of SB - register "fn_ctrl_lo" = "0" - register "fn_ctrl_hi" = "0xad" - - device pci 0.0 on end # HT - device pci f.1 on end # IDE - device pci 11.0 on # LPC - chip drivers/generic/generic #dimm 0-0-0 - device i2c 50 on end - end - chip drivers/generic/generic #dimm 0-0-1 - device i2c 51 on end - end - chip drivers/generic/generic #dimm 0-1-0 - device i2c 52 on end - end - chip drivers/generic/generic #dimm 0-1-1 - device i2c 53 on end - end - - chip superio/winbond/w83627ehg - device pnp 2e.0 on # Floppy - io 0x60 = 0x3f0 - irq 0x70 = 6 - drq 0x74 = 2 - end - device pnp 2e.1 on # Parallel Port - io 0x60 = 0x378 - irq 0x70 = 7 - drq 0x74 = 3 - end - device pnp 2e.2 on # Com1 - io 0x60 = 0x3f8 - irq 0x70 = 4 - end - device pnp 2e.3 off # Com2 - io 0x60 = 0x2f8 - irq 0x70 = 3 - end - device pnp 2e.5 off #keyb OFF - end - device pnp 2e.106 off # SERIAL_FLASH - io 0x60 = 0x100 - end - - device pnp 2e.007 off #GPIO1 off - end - device pnp 2e.107 on #GAME on - io 0x60 = 0x201 - end - device pnp 2e.207 on #MIDI on - io 0x62 = 0x330 - irq 0x70 = 0xa - end - device pnp 2e.307 off #GPIO6 off - end - device pnp 2e.8 off end # WDTO_PLED - device pnp 2e.009 on #GPIO2 on Logical device 9 is in sio_setup - end - device pnp 2e.109 off #GPIO3 off - end - device pnp 2e.209 off #GPIO4 off - end - device pnp 2e.309 on #GPIO5 on - end - device pnp 2e.a off end # ACPI - device pnp 2e.b on # HW Monitor - io 0x60 = 0x290 - irq 0x70 = 0 - end - end #end SIO - end #end 11 - - device pci 12.0 off end # VIA LAN is disabled, Asus used other chip - end - - chip southbridge/via/k8t890 - end - - end # device pci 18.0 - device pci 18.1 on end - device pci 18.2 on end - device pci 18.3 on end - end #mc0 - - end # pci_domain - -end # root_complex + chip southbridge/via/k8t890 # "Southbridge" K8T890 + end + end + device pci 18.1 on end + device pci 18.2 on end + device pci 18.3 on end + end + end +end diff --git a/src/mainboard/asus/a8v-e_se/Options.lb b/src/mainboard/asus/a8v-e_se/Options.lb index b6c5cea799..e9a623acf1 100644 --- a/src/mainboard/asus/a8v-e_se/Options.lb +++ b/src/mainboard/asus/a8v-e_se/Options.lb @@ -43,11 +43,9 @@ uses XIP_ROM_SIZE uses XIP_ROM_BASE uses STACK_SIZE uses HEAP_SIZE -##uses USE_OPTION_TABLE -##uses CONFIG_LB_MEM_TOPK - +# uses USE_OPTION_TABLE +# uses CONFIG_LB_MEM_TOPK uses HAVE_ACPI_TABLES - uses LB_CKS_RANGE_START uses LB_CKS_RANGE_END uses LB_CKS_LOC @@ -75,242 +73,96 @@ uses CONFIG_GDB_STUB uses CONFIG_CHIP_NAME uses CONFIG_CONSOLE_VGA uses CONFIG_PCI_ROM_RUN -#bx_b001- uses K8_HW_MEM_HOLE_SIZEK +# bx_b001- uses K8_HW_MEM_HOLE_SIZEK uses K8_HT_FREQ_1G_SUPPORT - uses USE_DCACHE_RAM uses DCACHE_RAM_BASE uses DCACHE_RAM_SIZE uses DCACHE_RAM_GLOBAL_VAR_SIZE uses CONFIG_USE_INIT - uses ENABLE_APIC_EXT_ID uses APIC_ID_OFFSET uses LIFT_BSP_APIC_ID - uses HT_CHAIN_UNITID_BASE uses HT_CHAIN_END_UNITID_BASE -#bx_b001- uses K8_SB_HT_CHAIN_ON_BUS0 +# bx_b001- uses K8_SB_HT_CHAIN_ON_BUS0 uses SB_HT_CHAIN_UNITID_OFFSET_ONLY -#bx_b005+ +# bx_b005+ uses SB_HT_CHAIN_ON_BUS0 - uses CONFIG_COMPRESSED_PAYLOAD_NRV2B uses CONFIG_COMPRESSED_PAYLOAD_LZMA -## ROM_SIZE is the size of boot ROM that this board will use. -#512K bytes -default ROM_SIZE=512 * 1024 - -#1M bytes -#bx- default ROM_SIZE=1024 * 1024 - -## -## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use -## -#256K -default FALLBACK_SIZE=256 * 1024 - -### -### Build options -### - -## -## Build code for the fallback boot -## -default HAVE_FALLBACK_BOOT=1 - -## -## Build code to reset the motherboard from coreboot -## -default HAVE_HARD_RESET=0 - -## -## Build code to export a programmable irq routing table -## -default HAVE_PIRQ_TABLE=0 -default IRQ_SLOT_COUNT=11 - -## -## Build code to export an x86 MP table -## Useful for specifying IRQ routing values -## -default HAVE_MP_TABLE=1 - -## -## Build code to export a CMOS option table -## -default HAVE_OPTION_TABLE=0 - -## -## Move the default coreboot cmos range off of AMD RTC registers -## -default LB_CKS_RANGE_START=49 -default LB_CKS_RANGE_END=122 -default LB_CKS_LOC=123 - -## -## Build code for SMP support -## Only worry about 2 micro processors -## -default CONFIG_SMP=1 -default CONFIG_MAX_CPUS=2 -default CONFIG_MAX_PHYSICAL_CPUS=1 -default CONFIG_LOGICAL_CPUS=1 - -#acpi -default HAVE_ACPI_TABLES=1 - -#CHIP_NAME ? -#default CONFIG_CHIP_NAME=1 - -#1G memory hole -#bx_b001- default K8_HW_MEM_HOLE_SIZEK=0x100000 - -#Opteron K8 1G HT Support -default K8_HT_FREQ_1G_SUPPORT=1 - -##HT Unit ID offset, default is 1, the typical one -default HT_CHAIN_UNITID_BASE=0x0 - -##real SB Unit ID, default is 0x20, mean dont touch it at last -#default HT_CHAIN_END_UNITID_BASE=0x0 - -#make the SB HT chain on bus 0, default is not (0) -#bx_b001- default K8_SB_HT_CHAIN_ON_BUS0=2 - -##bx_b005+ make the SB HT chain on bus 0 -default SB_HT_CHAIN_ON_BUS0=1 - -##only offset for SB chain?, default is yes(1) -default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0 - -#VGA -default CONFIG_CONSOLE_VGA=1 -default CONFIG_PCI_ROM_RUN=1 - -## -## enable CACHE_AS_RAM specifics -## -default USE_DCACHE_RAM=1 -default DCACHE_RAM_BASE=0xcc000 -default DCACHE_RAM_SIZE=0x4000 -default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000 -default CONFIG_USE_INIT=0 - -default ENABLE_APIC_EXT_ID=0 -default APIC_ID_OFFSET=0x10 -default LIFT_BSP_APIC_ID=0 - - -## -## Build code to setup a generic IOAPIC -## -default CONFIG_IOAPIC=1 - -## -## Clean up the motherboard id strings -## -default MAINBOARD_PART_NUMBER="A8V-E SE" -default MAINBOARD_VENDOR="ASUS" -default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x1043 -#default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1234 - -### -### coreboot layout values -### - -## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy. +default ROM_SIZE = 512 * 1024 +default FALLBACK_SIZE = 256 * 1024 +default HAVE_FALLBACK_BOOT = 1 +default HAVE_HARD_RESET = 0 +default HAVE_PIRQ_TABLE = 0 +default IRQ_SLOT_COUNT = 11 # FIXME? +default HAVE_MP_TABLE = 1 +default HAVE_OPTION_TABLE = 0 # FIXME +# Move the default coreboot CMOS range off of AMD RTC registers. +default LB_CKS_RANGE_START = 49 +default LB_CKS_RANGE_END = 122 +default LB_CKS_LOC = 123 +default CONFIG_SMP = 1 +default CONFIG_MAX_CPUS = 2 +default CONFIG_MAX_PHYSICAL_CPUS = 1 +default CONFIG_LOGICAL_CPUS = 1 +default HAVE_ACPI_TABLES = 1 +# default CONFIG_CHIP_NAME = 1 + +# 1G memory hole +# bx_b001- default K8_HW_MEM_HOLE_SIZEK = 0x100000 + +# Opteron K8 1G HT support +default K8_HT_FREQ_1G_SUPPORT = 1 + +# HT Unit ID offset, default is 1, the typical one. +default HT_CHAIN_UNITID_BASE = 0x0 + +# Real SB Unit ID, default is 0x20, mean don't touch it at last. +# default HT_CHAIN_END_UNITID_BASE = 0x0 + +# Make the SB HT chain on bus 0, default is not (0). +# bx_b001- default K8_SB_HT_CHAIN_ON_BUS0 = 2 + +# bx_b005+ make the SB HT chain on bus 0. +default SB_HT_CHAIN_ON_BUS0 = 1 + +# Only offset for SB chain?, default is yes(1). +default SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0 + +default CONFIG_CONSOLE_VGA = 1 # Needed for VGA. +default CONFIG_PCI_ROM_RUN = 1 # Needed for VGA. +default USE_DCACHE_RAM = 1 +default DCACHE_RAM_BASE = 0xcc000 +default DCACHE_RAM_SIZE = 0x4000 +default DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000 +default CONFIG_USE_INIT = 0 +default ENABLE_APIC_EXT_ID = 0 +default APIC_ID_OFFSET = 0x10 +default LIFT_BSP_APIC_ID = 0 +default CONFIG_IOAPIC = 1 +default MAINBOARD_VENDOR = "ASUS" +default MAINBOARD_PART_NUMBER = "A8V-E SE" +default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1043 +# default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x1234 # FIXME default ROM_IMAGE_SIZE = 64 * 1024 - -## -## Use a small 8K stack -## -default STACK_SIZE= 8 * 1024 - -## -## Use a small 256K heap -## -default HEAP_SIZE=256 * 1024 - -#more 1M for pgtbl -##default CONFIG_LB_MEM_TOPK=2048 - -## -## Only use the option table in a normal image -## -##default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE - -## -## Coreboot C code runs at this location in RAM -## -default _RAMBASE=0x00004000 - -## -## Load the payload from the ROM -## +default STACK_SIZE = 8 * 1024 +default HEAP_SIZE = 256 * 1024 +# More 1M for pgtbl. +# default CONFIG_LB_MEM_TOPK = 2048 +default _RAMBASE = 0x00004000 +# default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE default CONFIG_ROM_PAYLOAD = 1 - -### -### Defaults of options that you may want to override in the target config file -### - -## -## The default compiler -## -default CC="$(CROSS_COMPILE)gcc -m32" -default HOSTCC="gcc" - -## -## Disable the gdb stub by default -## -default CONFIG_GDB_STUB=0 - -## -## The Serial Console -## - -# To Enable the Serial Console -default CONFIG_CONSOLE_SERIAL8250=1 - -## Select the serial console baud rate -default TTYS0_BAUD=115200 -#default TTYS0_BAUD=57600 -#default TTYS0_BAUD=38400 -#default TTYS0_BAUD=19200 -#default TTYS0_BAUD=9600 -#default TTYS0_BAUD=4800 -#default TTYS0_BAUD=2400 -#default TTYS0_BAUD=1200 - -# Select the serial console base port -default TTYS0_BASE=0x3f8 - -# Select the serial protocol -# This defaults to 8 data bits, 1 stop bit, and no parity -default TTYS0_LCS=0x3 - -## -### Select the coreboot loglevel -## -## EMERG 1 system is unusable -## ALERT 2 action must be taken immediately -## CRIT 3 critical conditions -## ERR 4 error conditions -## WARNING 5 warning conditions -## NOTICE 6 normal but significant condition -## INFO 7 informational -## DEBUG 8 debug-level messages -## SPEW 9 Way too many details - -## Request this level of debugging output -default DEFAULT_CONSOLE_LOGLEVEL=8 -## At a maximum only compile in this level of debugging -default MAXIMUM_CONSOLE_LOGLEVEL=8 - -## -## Select power on after power fail setting -default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" - -### End Options.lb +default CC = "$(CROSS_COMPILE)gcc -m32" +default HOSTCC = "gcc" +default CONFIG_GDB_STUB = 0 +default CONFIG_CONSOLE_SERIAL8250 = 1 +default TTYS0_BAUD = 115200 +default TTYS0_BASE = 0x3f8 +default TTYS0_LCS = 0x3 # 8n1 +default DEFAULT_CONSOLE_LOGLEVEL = 8 +default MAXIMUM_CONSOLE_LOGLEVEL = 8 +default MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON" end diff --git a/src/mainboard/asus/a8v-e_se/acpi_tables.c b/src/mainboard/asus/a8v-e_se/acpi_tables.c index fa76d401f6..86fee0c99a 100644 --- a/src/mainboard/asus/a8v-e_se/acpi_tables.c +++ b/src/mainboard/asus/a8v-e_se/acpi_tables.c @@ -1,6 +1,7 @@ /* * This file is part of the coreboot project. - * written by Stefan Reinauer <stepan@openbios.org> + * + * Written by Stefan Reinauer <stepan@openbios.org>. * ACPI FADT, FACS, and DSDT table support added by * * Copyright (C) 2004 Stefan Reinauer <stepan@openbios.org> @@ -27,7 +28,6 @@ #include <arch/smp/mpspec.h> #include <device/device.h> #include <device/pci_ids.h> - #include <../../../southbridge/via/vt8237r/vt8237r.h> #include <../../../southbridge/via/k8t890/k8t890.h> @@ -37,6 +37,7 @@ unsigned long acpi_fill_mcfg(unsigned long current) { device_t dev; struct resource *res; + dev = dev_find_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_K8T890CE_5, 0); if (!dev) return current; @@ -53,36 +54,32 @@ unsigned long acpi_fill_madt(unsigned long current) { unsigned int gsi_base = 0x18; - /* create all subtables for processors */ + /* Create all subtables for processors. */ current = acpi_create_madt_lapics(current); - /* Write SB IOAPIC */ - current += - acpi_create_madt_ioapic((acpi_madt_ioapic_t *) current, VT8237R_APIC_ID, - VT8237R_APIC_BASE, 0); + /* Write SB IOAPIC. */ + current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *) current, + VT8237R_APIC_ID, VT8237R_APIC_BASE, 0); - /* Write NB IOAPIC */ - current += - acpi_create_madt_ioapic((acpi_madt_ioapic_t *) current, K8T890_APIC_ID, - K8T890_APIC_BASE, gsi_base); - /* IRQ9 ACPI active low */ + /* Write NB IOAPIC. */ + current += acpi_create_madt_ioapic((acpi_madt_ioapic_t *) current, + K8T890_APIC_ID, K8T890_APIC_BASE, gsi_base); + + /* IRQ9 ACPI active low. */ current += acpi_create_madt_irqoverride((acpi_madt_irqoverride_t *) - current, 0, 9, 9, MP_IRQ_TRIGGER_LEVEL | MP_IRQ_POLARITY_LOW); + current, 0, 9, 9, MP_IRQ_TRIGGER_LEVEL | MP_IRQ_POLARITY_LOW); - /* IRQ0 -> APIC IRQ2 */ + /* IRQ0 -> APIC IRQ2. */ current += acpi_create_madt_irqoverride((acpi_madt_irqoverride_t *) current, 0, 0, 2, 0x0); - /* create all subtables for processors */ - current = - acpi_create_madt_lapic_nmis(current, - MP_IRQ_TRIGGER_EDGE | - MP_IRQ_POLARITY_HIGH, 1); + /* Create all subtables for processors. */ + current = acpi_create_madt_lapic_nmis(current, + MP_IRQ_TRIGGER_EDGE | MP_IRQ_POLARITY_HIGH, 1); return current; } - unsigned long write_acpi_tables(unsigned long start) { unsigned long current; @@ -96,27 +93,25 @@ unsigned long write_acpi_tables(unsigned long start) acpi_facs_t *facs; acpi_header_t *dsdt; - /* Align ACPI tables to 16byte */ + /* Align ACPI tables to 16 byte. */ start = (start + 0x0f) & -0x10; current = start; printk_info("ACPI: Writing ACPI tables at %lx...\n", start); - /* We need at least an RSDP and an RSDT Table */ + /* We need at least an RSDP and an RSDT table. */ rsdp = (acpi_rsdp_t *) current; current += sizeof(acpi_rsdp_t); rsdt = (acpi_rsdt_t *) current; current += sizeof(acpi_rsdt_t); - /* clear all table memory */ + /* Clear all table memory. */ memset((void *) start, 0, current - start); acpi_write_rsdp(rsdp, rsdt); acpi_write_rsdt(rsdt); - /* - * We explicitly add these tables later on: - */ + /* We explicitly add these tables later on: */ printk_debug("ACPI: * FACS\n"); facs = (acpi_facs_t *) current; current += sizeof(acpi_facs_t); @@ -126,7 +121,7 @@ unsigned long write_acpi_tables(unsigned long start) current += ((acpi_header_t *) AmlCode)->length; memcpy((void *) dsdt, (void *) AmlCode, ((acpi_header_t *) AmlCode)->length); - dsdt->checksum = 0; // don't trust intel iasl compiler to get this right + dsdt->checksum = 0; /* Don't trust iasl to get this right. */ dsdt->checksum = acpi_checksum(dsdt, dsdt->length); printk_debug("ACPI: * DSDT @ %08x Length %x\n", dsdt, dsdt->length); @@ -144,7 +139,7 @@ unsigned long write_acpi_tables(unsigned long start) acpi_create_hpet(hpet); acpi_add_table(rsdt, hpet); - /* If we want to use HPET Timers Linux wants an MADT */ + /* If we want to use HPET timers Linux wants an MADT. */ printk_debug("ACPI: * MADT\n"); madt = (acpi_madt_t *) current; acpi_create_madt(madt); @@ -157,7 +152,6 @@ unsigned long write_acpi_tables(unsigned long start) current += mcfg->header.length; acpi_add_table(rsdt, mcfg); - /* SRAT */ printk_debug("ACPI: * SRAT\n"); srat = (acpi_srat_t *) current; acpi_create_srat(srat); diff --git a/src/mainboard/asus/a8v-e_se/cache_as_ram_auto.c b/src/mainboard/asus/a8v-e_se/cache_as_ram_auto.c index ca0fbd9197..796b87f581 100644 --- a/src/mainboard/asus/a8v-e_se/cache_as_ram_auto.c +++ b/src/mainboard/asus/a8v-e_se/cache_as_ram_auto.c @@ -2,10 +2,9 @@ * This file is part of the coreboot project. * * Copyright (C) 2006 AMD - * Written by Yinghai Lu <yinghailu@amd.com> for AMD. + * (Written by Yinghai Lu <yinghailu@amd.com> for AMD) * Copyright (C) 2006 MSI - * Written by Bingxun Shi <bingxunshi@gmail.com> for MSI. - * + * (Written by Bingxun Shi <bingxunshi@gmail.com> for MSI) * Copyright (C) 2007 Rudolf Marek <r.marek@assembler.cz> * * This program is free software; you can redistribute it and/or modify @@ -32,15 +31,16 @@ unsigned int get_sbdn(unsigned bus); -//used by raminit +/* Used by raminit. */ #define QRANK_DIMM_SUPPORT 1 -//used by init_cpus and fidvid +/* Used by init_cpus and fidvid */ #define K8_SET_FIDVID 1 -//if we want to wait for core1 done before DQS training, set it to 0 + +/* If we want to wait for core1 done before DQS training, set it to 0. */ #define K8_SET_FIDVID_CORE0_ONLY 1 -//#define DEBUG_SMBUS 1 +/* #define DEBUG_SMBUS 1 */ #include <stdint.h> #include <device/pci_def.h> @@ -50,31 +50,23 @@ unsigned int get_sbdn(unsigned bus); #include <cpu/x86/lapic.h> #include "option_table.h" #include "pc80/mc146818rtc_early.c" - #include "pc80/serial.c" #include "arch/i386/lib/console.c" - #include <cpu/amd/model_fxx_rev.h> #include "northbridge/amd/amdk8/raminit.h" #include "cpu/amd/model_fxx/apic_timer.c" #include "lib/delay.c" - #if CONFIG_USE_INIT == 0 #include "lib/memcpy.c" #endif - #include "cpu/x86/lapic/boot_cpu.c" #include "northbridge/amd/amdk8/reset_test.c" #include "northbridge/amd/amdk8/debug.c" #include "northbridge/amd/amdk8/early_ht.c" - - #include "superio/winbond/w83627ehg/w83627ehg_early_serial.c" #include "southbridge/via/vt8237r/vt8237r_early_smbus.c" - #include "cpu/amd/mtrr/amd_earlymtrr.c" #include "cpu/x86/bist.h" - #include "northbridge/amd/amdk8/setup_resource_map.c" #define SERIAL_DEV PNP_DEV(0x2e, W83627EHG_SP1) @@ -90,7 +82,6 @@ static void memreset(int controllers, const struct mem_controller *ctrl) { } - static inline int spd_read_byte(unsigned device, unsigned address) { return smbus_read_byte(device, address); @@ -103,34 +94,27 @@ static inline int spd_read_byte(unsigned device, unsigned address) #include "northbridge/amd/amdk8/coherent_ht.c" #include "northbridge/amd/amdk8/incoherent_ht.c" #include "sdram/generic_sdram.c" - #include "cpu/amd/dualcore/dualcore.c" - #include "southbridge/via/k8t890/k8t890_early_car.c" - #include "cpu/amd/car/copy_and_run.c" - #include "cpu/amd/car/post_cache_as_ram.c" - #include "cpu/amd/model_fxx/init_cpus.c" #include "cpu/amd/model_fxx/fidvid.c" - #include "northbridge/amd/amdk8/resourcemap.c" - void activate_spd_rom(const struct mem_controller *ctrl) { - } void hard_reset(void) { - print_info("NO HARD RESET FIX ME!\n"); + print_info("NO HARD RESET. FIX ME!\n"); } void soft_reset(void) { uint8_t tmp; + set_bios_reset(); print_debug("soft reset \r\n"); @@ -154,26 +138,29 @@ unsigned int get_sbdn(unsigned bus) return (dev >> 15) & 0x1f; } - -void sio_init(void) { +void sio_init(void) +{ u8 reg; pnp_enter_ext_func_mode(SERIAL_DEV); + /* We have 24MHz input. */ reg = pnp_read_config(SERIAL_DEV, 0x24); - pnp_write_config(SERIAL_DEV, 0x24, (reg & ~0x40)); /* we have 24MHz input */ - - reg = pnp_read_config(SERIAL_DEV, 0x2A); - pnp_write_config(SERIAL_DEV, 0x2A, (reg | 1)); /* we have GPIO for KB/MS PIN */ - - reg = pnp_read_config(SERIAL_DEV, 0x2C); - pnp_write_config(SERIAL_DEV, 0x2C, (reg | 0xf0)); /* we have all RESTOUT and even some reserved bits too */ - + pnp_write_config(SERIAL_DEV, 0x24, (reg & ~0x40)); + /* We have GPIO for KB/MS pin. */ + reg = pnp_read_config(SERIAL_DEV, 0x2a); + pnp_write_config(SERIAL_DEV, 0x2a, (reg | 1)); + /* We have all RESTOUT and even some reserved bits, too. */ + reg = pnp_read_config(SERIAL_DEV, 0x2c); + pnp_write_config(SERIAL_DEV, 0x2c, (reg | 0xf0)); pnp_exit_ext_func_mode(SERIAL_DEV); pnp_enter_ext_func_mode(ACPI_DEV); pnp_set_logical_device(ACPI_DEV); + /* + * Set the delay rising time from PWROK_LP to PWROK_ST to + * 300 - 600ms, and 0 to vice versa. + */ reg = pnp_read_config(ACPI_DEV, 0xe6); - /* Set the delay rising time from PWROK_LP to PWROK_ST to 300 - 600ms, and 0 to vice versa */ pnp_write_config(ACPI_DEV, 0xe6, (reg & 0xf0)); /* 1 Use external suspend clock source 32.768KHz. Undocumented?? */ reg = pnp_read_config(ACPI_DEV, 0xe4); @@ -182,15 +169,14 @@ void sio_init(void) { pnp_enter_ext_func_mode(GPIO_DEV); pnp_set_logical_device(GPIO_DEV); - - /* set memory voltage to 2.75V, vcore offset + 100mV, 1.5V Chipset voltage */ - pnp_write_config(GPIO_DEV, 0x30, 0x9); /* Enable GPIO 2 & GPIO 5 */ - pnp_write_config(GPIO_DEV, 0xe2, 0x0); /* no inversion */ - pnp_write_config(GPIO_DEV, 0xe5, 0x0); /* no inversion */ - pnp_write_config(GPIO_DEV, 0xe3, 0x3); /* 0000 0011 0=output 1=input */ - pnp_write_config(GPIO_DEV, 0xe0, 0xde); /* 1101110 0=output 1=input */ - pnp_write_config(GPIO_DEV, 0xe1, 0x1); /* set output val */ - pnp_write_config(GPIO_DEV, 0xe4, 0xb4); /* set output val 1011 0100 */ + /* Set memory voltage to 2.75V, vcore offset + 100mV, 1.5V chipset voltage. */ + pnp_write_config(GPIO_DEV, 0x30, 0x09); /* Enable GPIO 2 & GPIO 5. */ + pnp_write_config(GPIO_DEV, 0xe2, 0x00); /* No inversion */ + pnp_write_config(GPIO_DEV, 0xe5, 0x00); /* No inversion */ + pnp_write_config(GPIO_DEV, 0xe3, 0x03); /* 0000 0011, 0=output 1=input */ + pnp_write_config(GPIO_DEV, 0xe0, 0xde); /* 1101 1110, 0=output 1=input */ + pnp_write_config(GPIO_DEV, 0xe1, 0x01); /* Set output val. */ + pnp_write_config(GPIO_DEV, 0xe4, 0xb4); /* Set output val (1011 0100). */ pnp_exit_ext_func_mode(GPIO_DEV); } @@ -198,8 +184,8 @@ void sio_init(void) { void failover_process(unsigned long bist, unsigned long cpu_init_detectedx) { -// unsigned last_boot_normal_x = last_boot_normal(); -//FIXME + /* unsigned last_boot_normal_x = last_boot_normal(); */ + /* FIXME */ unsigned last_boot_normal_x = 1; sio_init(); @@ -209,56 +195,50 @@ void failover_process(unsigned long bist, unsigned long cpu_init_detectedx) print_info("now booting... fallback\r\n"); - /* Is this a cpu only reset? or Is this a secondary cpu? */ + /* Is this a CPU only reset? Or is this a secondary CPU? */ if ((cpu_init_detectedx) || (!boot_cpu())) { - if (last_boot_normal_x) { + if (last_boot_normal_x) goto normal_image; - } else { + else goto fallback_image; - } } - /* Nothing special needs to be done to find bus 0 */ - /* Allow the HT devices to be found */ - + /* Nothing special needs to be done to find bus 0. */ + /* Allow the HT devices to be found. */ enumerate_ht_chain(); - /* Is this a deliberate reset by the bios */ + /* Is this a deliberate reset by the BIOS? */ if (bios_reset_detected() && last_boot_normal_x) { goto normal_image; } - /* This is the primary cpu how should I boot? */ + /* This is the primary CPU, how should I boot? */ else if (do_normal_boot()) { goto normal_image; } else { goto fallback_image; } - normal_image: - //print_info("JMP normal image\r\n"); - __asm__ volatile ("jmp __normal_image": /* outputs */ - :"a" (bist), "b"(cpu_init_detectedx) /* inputs */ - ); +normal_image: + /* print_info("JMP normal image\r\n"); */ + + __asm__ __volatile__("jmp __normal_image": + :"a" (bist), "b" (cpu_init_detectedx)); - fallback_image: +fallback_image: ; } #endif void real_main(unsigned long bist, unsigned long cpu_init_detectedx); -void cache_as_ram_main(unsigned long bist, - unsigned long cpu_init_detectedx) +void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) { - #if USE_FALLBACK_IMAGE == 1 failover_process(bist, cpu_init_detectedx); #endif real_main(bist, cpu_init_detectedx); - } - void real_main(unsigned long bist, unsigned long cpu_init_detectedx) { static const uint16_t spd_addr[] = { @@ -272,8 +252,7 @@ void real_main(unsigned long bist, unsigned long cpu_init_detectedx) unsigned bsp_apicid = 0; int needs_reset = 0; struct sys_info *sysinfo = - (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - - DCACHE_RAM_GLOBAL_VAR_SIZE); + (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); char *p; sio_init(); @@ -283,23 +262,25 @@ void real_main(unsigned long bist, unsigned long cpu_init_detectedx) print_info("now booting... real_main\r\n"); - if (bist == 0) { + if (bist == 0) bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); - } - /* Halt if there was a built in self test failure */ + + /* Halt if there was a built in self test failure. */ report_bist_failure(bist); + setup_default_resource_map(); setup_coherent_ht_domain(); wait_all_core0_started(); + print_info("now booting... Core0 started\r\n"); #if CONFIG_LOGICAL_CPUS==1 - // It is said that we should start core1 after all core0 launched + /* It is said that we should start core1 after all core0 launched. */ start_other_cores(); wait_all_other_cores_started(bsp_apicid); #endif init_timer(); - ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn + ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */ enable_fid_change(); init_fidvid_bsp(bsp_apicid); @@ -307,20 +288,22 @@ void real_main(unsigned long bist, unsigned long cpu_init_detectedx) needs_reset = optimize_link_coherent_ht(); needs_reset |= optimize_link_incoherent_ht(sysinfo); - /* Fixme it assumes that 1000MHz LDT is selected. */ + /* FIXME: Assumes that 1000MHz LDT is selected. */ needs_reset |= k8t890_early_setup_car(16, 0x6); if (needs_reset) { print_debug("ht reset -\r\n"); soft_reset(); } - /* stop the APs so we can start them later in init */ - allow_all_aps_stop(bsp_apicid); - /* It's the time to set ctrl now; */ + + /* Stop the APs so we can start them later in init. */ + allow_all_aps_stop(bsp_apicid); + + /* It's the time to set ctrl now. */ fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); + enable_smbus(); memreset_setup(); sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo); post_cache_as_ram(); } - diff --git a/src/mainboard/asus/a8v-e_se/chip.h b/src/mainboard/asus/a8v-e_se/chip.h index 77f099cd95..101113437d 100644 --- a/src/mainboard/asus/a8v-e_se/chip.h +++ b/src/mainboard/asus/a8v-e_se/chip.h @@ -20,5 +20,4 @@ extern struct chip_operations mainboard_asus_a8v_e_se_ops; struct mainboard_asus_a8v_e_se_config { - }; diff --git a/src/mainboard/asus/a8v-e_se/dsdt.asl b/src/mainboard/asus/a8v-e_se/dsdt.asl index 220e6c81e4..144fcf2459 100644 --- a/src/mainboard/asus/a8v-e_se/dsdt.asl +++ b/src/mainboard/asus/a8v-e_se/dsdt.asl @@ -1,12 +1,11 @@ /* * This file is part of the coreboot project. * - * Minimalist ACPI DSDT table for EPIA-M / MII * (C) Copyright 2004 Nick Barker <Nick.Barker9@btinternet.com> - * * (C) Copyright 2007 Rudolf Marek <r.marek@assembler.cz> * - * ISA portions taken from QEMU acpi-dsdt.dsl + * ISA portions taken from QEMU acpi-dsdt.dsl. + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License v2 as published by * the Free Software Foundation. @@ -21,16 +20,9 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ - DefinitionBlock ("DSDT.aml", "DSDT", 1, "LXBIOS", "LXB-DSDT", 1) { - - - - - /* - * Define the main processor - */ + /* Define the main processor.*/ Scope (\_PR) { Processor (\_PR.CPU0, 0x00, 0x000000, 0x00) {} @@ -40,206 +32,178 @@ DefinitionBlock ("DSDT.aml", "DSDT", 1, "LXBIOS", "LXB-DSDT", 1) /* For now only define 2 power states: * - S0 which is fully on * - S5 which is soft off - * any others would involve declaring the wake up methods + * Any others would involve declaring the wake up methods. */ - Name (\_S0, Package () {0x00, 0x00, 0x00, 0x00 }) - Name (\_S5, Package () {0x02, 0x02, 0x00, 0x00 }) + Name (\_S0, Package () { 0x00, 0x00, 0x00, 0x00 }) + Name (\_S5, Package () { 0x02, 0x02, 0x00, 0x00 }) /* Root of the bus hierarchy */ Scope (\_SB) - { - /* top PCI device */ + { + /* Top PCI device */ Device (PCI0) { Name (_HID, EisaId ("PNP0A03")) Name (_ADR, 0x00) Name (_UID, 0x00) Name (_BBN, 0x00) - - /* PCI Routing Table */ - //aaa - Name (_PRT, Package () { - Package (0x04) { 0x000BFFFF, 0x00, 0x00, 0x10 }, //slot 0xB - Package (0x04) { 0x000BFFFF, 0x01, 0x00, 0x11 }, - Package (0x04) { 0x000BFFFF, 0x02, 0x00, 0x12 }, - Package (0x04) { 0x000BFFFF, 0x03, 0x00, 0x13 }, - Package (0x04) { 0x000CFFFF, 0x00, 0x00, 0x11 }, //Slot 0xC - Package (0x04) { 0x000CFFFF, 0x01, 0x00, 0x12 }, - Package (0x04) { 0x000CFFFF, 0x02, 0x00, 0x13 }, - Package (0x04) { 0x000CFFFF, 0x03, 0x00, 0x10 }, - Package (0x04) { 0x000DFFFF, 0x00, 0x00, 0x12 }, //Slot 0xD - Package (0x04) { 0x000DFFFF, 0x01, 0x00, 0x13 }, - Package (0x04) { 0x000DFFFF, 0x02, 0x00, 0x10 }, - Package (0x04) { 0x000DFFFF, 0x03, 0x00, 0x11 }, - Package (0x04) { 0x000F0000, 0x01, 0x00, 0x14 }, //0xf SATA IRQ 20 - Package (0x04) { 0x000F0001, 0x00, 0x00, 0x14 }, //0xf NAtive IDE IRQ 20 - Package (0x04) { 0x0010FFFF, 0x00, 0x00, 0x15 }, //USB routing - Package (0x04) { 0x0010FFFF, 0x01, 0x00, 0x15 }, - Package (0x04) { 0x0010FFFF, 0x02, 0x00, 0x15 }, - Package (0x04) { 0x0010FFFF, 0x03, 0x00, 0x15 }, - Package (0x04) { 0x0011FFFF, 0x02, 0x00, 0x16 }, //AC97 MC97 - Package (0x04) { 0x0002FFFF, 0x00, 0x00, 0x1B }, //PCIE16 bridge IRQ27 - Package (0x04) { 0x0002FFFF, 0x01, 0x00, 0x1B }, - Package (0x04) { 0x0002FFFF, 0x02, 0x00, 0x1B }, - Package (0x04) { 0x0002FFFF, 0x03, 0x00, 0x1B }, - Package (0x04) { 0x0003FFFF, 0x00, 0x00, 0x1F }, //PCIE bridge IRQ31 - Package (0x04) { 0x0003FFFF, 0x01, 0x00, 0x23 }, //IRQ36 - Package (0x04) { 0x0003FFFF, 0x02, 0x00, 0x27 }, //IRQ39 - Package (0x04) { 0x0003FFFF, 0x03, 0x00, 0x2B } //IRQ43 - }) - - Device (PEGG) - { - Name (_ADR, 0x00020000) - Name (_UID, 0x00) - Name (_BBN, 0x02) - - Name (_PRT, Package () { - Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x18 }, //PCIE IRQ24-IRQ27 - Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x19 }, - Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x1A }, - Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x1B }, - }) - } //end of PCIEG - - Device (PEX0) - { - Name (_ADR, 0x00030000) - Name (_UID, 0x00) - Name (_BBN, 0x03) - - Name (_PRT, Package () { - Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x1C }, //PCIE IRQ28-IRQ31 - Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x1D }, - Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x1E }, - Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x1F }, - }) - } //end of PEX0 - - Device (PEX1) - { - Name (_ADR, 0x00030001) - Name (_UID, 0x00) - Name (_BBN, 0x04) - - Name (_PRT, Package () { - Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x20 }, //PCIE IRQ32-IRQ35 - Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x21 }, - Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x22 }, - Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x23 }, - }) - } //end f PEX1 - - Device (PEX2) - { - Name (_ADR, 0x00030002) - Name (_UID, 0x00) - Name (_BBN, 0x05) - - Name (_PRT, Package () { - Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x24 }, //PCIE IRQ36-IRQ39 - Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x25 }, - Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x26 }, - Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x27 }, - }) - } //end f PEX2 - - Device (PEX3) - { - Name (_ADR, 0x00030003) - Name (_UID, 0x00) - Name (_BBN, 0x06) - + /* PCI Routing Table */ + /* aaa */ Name (_PRT, Package () { - Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x28 }, //PCIE IRQ40-IRQ43 - Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x29 }, - Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x2A }, - Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x2B }, - }) - } //end f PEX3 - - Device (ISA) { - Name (_ADR, 0x00110000) - - /* Keyboard seems to be important for WinXP install */ - Device (KBD) - { - Name (_HID, EisaId ("PNP0303")) - Method (_STA, 0, NotSerialized) - { - Return (0x0f) - } - - Method (_CRS, 0, NotSerialized) - { - Name (TMP, ResourceTemplate () - { - IO (Decode16, - 0x0060, // Address Range Minimum - 0x0060, // Address Range Maximum - 0x01, // Address Alignment - 0x01, // Address Length - ) - IO (Decode16, - 0x0064, // Address Range Minimum - 0x0064, // Address Range Maximum - 0x01, // Address Alignment - 0x01, // Address Length - ) - IRQNoFlags () - {1} - }) - Return (TMP) - } - } - - /* PS/2 mouse */ - Device (MOU) - { - Name (_HID, EisaId ("PNP0F13")) - Method (_STA, 0, NotSerialized) - { - Return (0x0f) - } - - Method (_CRS, 0, NotSerialized) - { - Name (TMP, ResourceTemplate () - { - IRQNoFlags () {12} - }) - Return (TMP) - } - } - - /* PS/2 floppy controller */ - Device (FDC0) - { - Name (_HID, EisaId ("PNP0700")) - Method (_STA, 0, NotSerialized) - { - Return (0x0F) - } - Method (_CRS, 0, NotSerialized) - { - Name (BUF0, ResourceTemplate () - { - IO (Decode16, 0x03F2, 0x03F2, 0x00, 0x04) - IO (Decode16, 0x03F7, 0x03F7, 0x00, 0x01) - IRQNoFlags () {6} - DMA (Compatibility, NotBusMaster, Transfer8) {2} - }) - Return (BUF0) + Package (0x04) { 0x000BFFFF, 0x00, 0x00, 0x10 }, /* Slot 0xB */ + Package (0x04) { 0x000BFFFF, 0x01, 0x00, 0x11 }, + Package (0x04) { 0x000BFFFF, 0x02, 0x00, 0x12 }, + Package (0x04) { 0x000BFFFF, 0x03, 0x00, 0x13 }, + Package (0x04) { 0x000CFFFF, 0x00, 0x00, 0x11 }, /* Slot 0xC */ + Package (0x04) { 0x000CFFFF, 0x01, 0x00, 0x12 }, + Package (0x04) { 0x000CFFFF, 0x02, 0x00, 0x13 }, + Package (0x04) { 0x000CFFFF, 0x03, 0x00, 0x10 }, + Package (0x04) { 0x000DFFFF, 0x00, 0x00, 0x12 }, /* Slot 0xD */ + Package (0x04) { 0x000DFFFF, 0x01, 0x00, 0x13 }, + Package (0x04) { 0x000DFFFF, 0x02, 0x00, 0x10 }, + Package (0x04) { 0x000DFFFF, 0x03, 0x00, 0x11 }, + Package (0x04) { 0x000F0000, 0x01, 0x00, 0x14 }, /* 0xf SATA IRQ 20 */ + Package (0x04) { 0x000F0001, 0x00, 0x00, 0x14 }, /* 0xf Native IDE IRQ 20 */ + Package (0x04) { 0x0010FFFF, 0x00, 0x00, 0x15 }, /* USB routing */ + Package (0x04) { 0x0010FFFF, 0x01, 0x00, 0x15 }, + Package (0x04) { 0x0010FFFF, 0x02, 0x00, 0x15 }, + Package (0x04) { 0x0010FFFF, 0x03, 0x00, 0x15 }, + Package (0x04) { 0x0011FFFF, 0x02, 0x00, 0x16 }, /* AC97, MC97 */ + Package (0x04) { 0x0002FFFF, 0x00, 0x00, 0x1B }, /* PCIE16 bridge IRQ27 */ + Package (0x04) { 0x0002FFFF, 0x01, 0x00, 0x1B }, + Package (0x04) { 0x0002FFFF, 0x02, 0x00, 0x1B }, + Package (0x04) { 0x0002FFFF, 0x03, 0x00, 0x1B }, + Package (0x04) { 0x0003FFFF, 0x00, 0x00, 0x1F }, /* PCIE bridge IRQ31 */ + Package (0x04) { 0x0003FFFF, 0x01, 0x00, 0x23 }, /* IRQ36 */ + Package (0x04) { 0x0003FFFF, 0x02, 0x00, 0x27 }, /* IRQ39 */ + Package (0x04) { 0x0003FFFF, 0x03, 0x00, 0x2B } /* IRQ43 */ + }) + + Device (PEGG) + { + Name (_ADR, 0x00020000) + Name (_UID, 0x00) + Name (_BBN, 0x02) + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x18 }, /* PCIE IRQ24-IRQ27 */ + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x19 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x1A }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x1B }, + }) + } + + Device (PEX0) + { + Name (_ADR, 0x00030000) + Name (_UID, 0x00) + Name (_BBN, 0x03) + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x1C }, /* PCIE IRQ28-IRQ31 */ + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x1D }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x1E }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x1F }, + }) + } + + Device (PEX1) + { + Name (_ADR, 0x00030001) + Name (_UID, 0x00) + Name (_BBN, 0x04) + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x20 }, /* PCIE IRQ32-IRQ35 */ + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x21 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x22 }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x23 }, + }) + } + + Device (PEX2) + { + Name (_ADR, 0x00030002) + Name (_UID, 0x00) + Name (_BBN, 0x05) + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x24 }, /* PCIE IRQ36-IRQ39 */ + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x25 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x26 }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x27 }, + }) + } + + Device (PEX3) + { + Name (_ADR, 0x00030003) + Name (_UID, 0x00) + Name (_BBN, 0x06) + Name (_PRT, Package () { + Package (0x04) { 0x0000FFFF, 0x00, 0x00, 0x28 }, /* PCIE IRQ40-IRQ43 */ + Package (0x04) { 0x0000FFFF, 0x01, 0x00, 0x29 }, + Package (0x04) { 0x0000FFFF, 0x02, 0x00, 0x2A }, + Package (0x04) { 0x0000FFFF, 0x03, 0x00, 0x2B }, + }) + } + + Device (ISA) { + Name (_ADR, 0x00110000) + + /* PS/2 keyboard (seems to be important for WinXP install) */ + Device (KBD) + { + Name (_HID, EisaId ("PNP0303")) + Method (_STA, 0, NotSerialized) + { + Return (0x0f) + } + Method (_CRS, 0, NotSerialized) + { + Name (TMP, ResourceTemplate () { + IO (Decode16, 0x0060, 0x0060, 0x01, 0x01) + IO (Decode16, 0x0064, 0x0064, 0x01, 0x01) + IRQNoFlags () {1} + }) + Return (TMP) + } + } + + /* PS/2 mouse */ + Device (MOU) + { + Name (_HID, EisaId ("PNP0F13")) + Method (_STA, 0, NotSerialized) + { + Return (0x0f) + } + Method (_CRS, 0, NotSerialized) + { + Name (TMP, ResourceTemplate () { + IRQNoFlags () {12} + }) + Return (TMP) + } + } + + /* PS/2 floppy controller */ + Device (FDC0) + { + Name (_HID, EisaId ("PNP0700")) + Method (_STA, 0, NotSerialized) + { + Return (0x0f) + } + Method (_CRS, 0, NotSerialized) + { + Name (BUF0, ResourceTemplate () { + IO (Decode16, 0x03F2, 0x03F2, 0x00, 0x04) + IO (Decode16, 0x03F7, 0x03F7, 0x00, 0x01) + IRQNoFlags () {6} + DMA (Compatibility, NotBusMaster, Transfer8) {2} + }) + Return (BUF0) + } + } + } } - } //FD END - - } //ISA END - - } // End of PCI0 - - - } // End of _SB - -} // End of Definition Block - + } +} diff --git a/src/mainboard/asus/a8v-e_se/fadt.c b/src/mainboard/asus/a8v-e_se/fadt.c index d4e3003512..a5386d7880 100644 --- a/src/mainboard/asus/a8v-e_se/fadt.c +++ b/src/mainboard/asus/a8v-e_se/fadt.c @@ -1,7 +1,8 @@ /* - * ACPI - create the Fixed ACPI Description Tables (FADT) - * (C) Copyright 2004 Nick Barker <nick.barker9@btinternet.com> - * (C) Copyright 2007 Rudolf Marek <r.marek@assembler.cz> + * This file is part of the coreboot project. + * + * Copyright (C) 2004 Nick Barker <nick.barker9@btinternet.com> + * Copyright (C) 2007 Rudolf Marek <r.marek@assembler.cz> * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -15,15 +16,17 @@ * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, - * MA 02110-1301 USA + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ #include <string.h> #include <arch/acpi.h> #include <../../../southbridge/via/vt8237r/vt8237r.h> -void acpi_create_fadt(acpi_fadt_t * fadt, acpi_facs_t * facs, void *dsdt) +/** + * Create the Fixed ACPI Description Tables (FADT) for this board. + */ +void acpi_create_fadt(acpi_fadt_t *fadt, acpi_facs_t *facs, void *dsdt) { acpi_header_t *header = &(fadt->header); @@ -146,6 +149,5 @@ void acpi_create_fadt(acpi_fadt_t * fadt, acpi_facs_t * facs, void *dsdt) fadt->x_gpe1_blk.addrl = 0x0; fadt->x_gpe1_blk.addrh = 0x0; - header->checksum = - acpi_checksum((void *) fadt, sizeof(acpi_fadt_t)); + header->checksum = acpi_checksum((void *) fadt, sizeof(acpi_fadt_t)); } diff --git a/src/mainboard/asus/a8v-e_se/mainboard.c b/src/mainboard/asus/a8v-e_se/mainboard.c index 79ea4f0e3b..c06fbffd60 100644 --- a/src/mainboard/asus/a8v-e_se/mainboard.c +++ b/src/mainboard/asus/a8v-e_se/mainboard.c @@ -21,7 +21,6 @@ #include <device/device.h> #include <device/pci.h> #include <device/pci_ids.h> -#include <device/pci_ops.h> #include "chip.h" #if CONFIG_CHIP_NAME == 1 diff --git a/src/mainboard/asus/a8v-e_se/mptable.c b/src/mainboard/asus/a8v-e_se/mptable.c index 1cb7739cf9..bdf1d7cc50 100644 --- a/src/mainboard/asus/a8v-e_se/mptable.c +++ b/src/mainboard/asus/a8v-e_se/mptable.c @@ -17,43 +17,42 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ -#include <arch/smp/mpspec.h> #include <string.h> #include <stdint.h> - +#include <arch/smp/mpspec.h> #include <../../../southbridge/via/vt8237r/vt8237r.h> #include <../../../southbridge/via/k8t890/k8t890.h> void *smp_write_config_table(void *v) { - static const char sig[4] = "PCMP"; - static const char oem[8] = "LNXB "; - static const char productid[12] = "A8V-E SE "; - struct mp_config_table *mc; + static const char sig[4] = "PCMP"; + static const char oem[8] = "LNXB "; + static const char productid[12] = "A8V-E SE "; + struct mp_config_table *mc; unsigned int conforms = 0; int bus_isa = 42; - mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN); - memset(mc, 0, sizeof(*mc)); + mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN); + memset(mc, 0, sizeof(*mc)); - memcpy(mc->mpc_signature, sig, sizeof(sig)); - mc->mpc_length = sizeof(*mc); /* initially just the header */ - mc->mpc_spec = 0x04; - mc->mpc_checksum = 0; /* not yet computed */ - memcpy(mc->mpc_oem, oem, sizeof(oem)); - memcpy(mc->mpc_productid, productid, sizeof(productid)); - mc->mpc_oemptr = 0; - mc->mpc_oemsize = 0; - mc->mpc_entry_count = 0; /* No entries yet... */ - mc->mpc_lapic = LAPIC_ADDR; - mc->mpe_length = 0; - mc->mpe_checksum = 0; - mc->reserved = 0; + memcpy(mc->mpc_signature, sig, sizeof(sig)); + mc->mpc_length = sizeof(*mc); /* Initially just the header. */ + mc->mpc_spec = 0x04; + mc->mpc_checksum = 0; /* Not yet computed. */ + memcpy(mc->mpc_oem, oem, sizeof(oem)); + memcpy(mc->mpc_productid, productid, sizeof(productid)); + mc->mpc_oemptr = 0; + mc->mpc_oemsize = 0; + mc->mpc_entry_count = 0; /* No entries yet. */ + mc->mpc_lapic = LAPIC_ADDR; + mc->mpe_length = 0; + mc->mpe_checksum = 0; + mc->reserved = 0; - smp_write_processors(mc); + smp_write_processors(mc); -/*Bus: Bus ID Type*/ + /* Bus: Bus ID Type */ smp_write_bus(mc, 0, "PCI "); smp_write_bus(mc, 1, "PCI "); smp_write_bus(mc, 2, "PCI "); @@ -62,12 +61,11 @@ void *smp_write_config_table(void *v) smp_write_bus(mc, 5, "PCI "); smp_write_bus(mc, 6, "PCI "); smp_write_bus(mc, bus_isa, "ISA "); -/*I/O APICs: APIC ID Version State Address*/ + /* I/O APICs: APIC ID Version State Address */ smp_write_ioapic(mc, VT8237R_APIC_ID, 0x20, VT8237R_APIC_BASE); smp_write_ioapic(mc, K8T890_APIC_ID, 0x20, K8T890_APIC_BASE); - smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, VT8237R_APIC_ID, 0x0); smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x1, VT8237R_APIC_ID, 0x1); smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, VT8237R_APIC_ID, 0x2); @@ -142,14 +140,16 @@ void *smp_write_config_table(void *v) smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x6, (0x00 << 2) | 2, K8T890_APIC_ID, 0x12); smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x6, (0x00 << 2) | 3, K8T890_APIC_ID, 0x13); -/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/ - smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x0); - smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x1); + /* Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# */ + smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x0); + smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x1); /* There is no extension information... */ - /* Compute the checksums */ - mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length); + /* Compute the checksums. */ + mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), + mc->mpe_length); mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length); + return smp_next_mpe_entry(mc); } |