diff options
Diffstat (limited to 'src/mainboard/digitallogic/msm800sev/Options.lb')
| -rw-r--r-- | src/mainboard/digitallogic/msm800sev/Options.lb | 162 |
1 files changed, 162 insertions, 0 deletions
diff --git a/src/mainboard/digitallogic/msm800sev/Options.lb b/src/mainboard/digitallogic/msm800sev/Options.lb new file mode 100644 index 0000000000..ec4c78c330 --- /dev/null +++ b/src/mainboard/digitallogic/msm800sev/Options.lb @@ -0,0 +1,162 @@ +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses HAVE_OPTION_TABLE +uses USE_OPTION_TABLE +uses CONFIG_ROM_STREAM +uses IRQ_SLOT_COUNT +uses MAINBOARD +uses MAINBOARD_VENDOR +uses MAINBOARD_PART_NUMBER +uses LINUXBIOS_EXTRA_VERSION +uses ARCH +uses FALLBACK_SIZE +uses STACK_SIZE +uses HEAP_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_STREAM_START +uses CONFIG_COMPRESSED_ROM_STREAM_NRV2B +uses PAYLOAD_SIZE +uses _ROMBASE +uses _RAMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses HAVE_MP_TABLE +uses CROSS_COMPILE +uses CC +uses HOSTCC +uses OBJCOPY +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses CONFIG_CONSOLE_SERIAL8250 +uses TTYS0_BAUD +uses TTYS0_BASE +uses TTYS0_LCS +uses CONFIG_UDELAY_TSC +uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 + +## ROM_SIZE is the size of boot ROM that this board will use. +default ROM_SIZE = 256*1024 + +### +### Build options +### + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 + +## +## no MP table +## +default HAVE_MP_TABLE=0 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=0 + +## Delay timer options +## +default CONFIG_UDELAY_TSC=1 +default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=0 +default IRQ_SLOT_COUNT=6 + +#object irq_tables.o + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=0 + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 65536 +default FALLBACK_SIZE = 131072 + +## +## Use a small 8K stack +## +default STACK_SIZE=0x2000 + +## +## Use a small 16K heap +## +default HEAP_SIZE=0x4000 + +## +## Only use the option table in a normal image +## +#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE +default USE_OPTION_TABLE = 0 + +default _RAMBASE = 0x00004000 + +default CONFIG_ROM_STREAM = 1 + +## +## The default compiler +## +default CROSS_COMPILE="" +default CC="$(CROSS_COMPILE)gcc -m32" +default HOSTCC="gcc" + +## +## The Serial Console +## + +# To Enable the Serial Console +default CONFIG_CONSOLE_SERIAL8250=1 + +## Select the serial console baud rate +default TTYS0_BAUD=115200 +#default TTYS0_BAUD=57600 +#default TTYS0_BAUD=38400 +#default TTYS0_BAUD=19200 +#default TTYS0_BAUD=9600 +#default TTYS0_BAUD=4800 +#default TTYS0_BAUD=2400 +#default TTYS0_BAUD=1200 + +# Select the serial console base port +default TTYS0_BASE=0x3f8 + +# Select the serial protocol +# This defaults to 8 data bits, 1 stop bit, and no parity +default TTYS0_LCS=0x3 + +## +### Select the linuxBIOS loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +default DEFAULT_CONSOLE_LOGLEVEL=8 +## At a maximum only compile in this level of debugging +default MAXIMUM_CONSOLE_LOGLEVEL=8 + +end + |