diff options
Diffstat (limited to 'src/mainboard/google/glados/variants/asuka/devicetree.cb')
| -rw-r--r-- | src/mainboard/google/glados/variants/asuka/devicetree.cb | 288 |
1 files changed, 288 insertions, 0 deletions
diff --git a/src/mainboard/google/glados/variants/asuka/devicetree.cb b/src/mainboard/google/glados/variants/asuka/devicetree.cb new file mode 100644 index 0000000000..cbd8b01821 --- /dev/null +++ b/src/mainboard/google/glados/variants/asuka/devicetree.cb @@ -0,0 +1,288 @@ +chip soc/intel/skylake + + # Enable deep Sx states + register "deep_s3_enable_ac" = "0" + register "deep_s3_enable_dc" = "0" + register "deep_s5_enable_ac" = "1" + register "deep_s5_enable_dc" = "1" + register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN" + + # GPE configuration + # Note that GPE events called out in ASL code rely on this + # route. i.e. If this route changes then the affected GPE + # offset bits also need to be changed. + register "gpe0_dw0" = "GPP_B" + register "gpe0_dw1" = "GPP_D" + register "gpe0_dw2" = "GPP_E" + + # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f + register "gen1_dec" = "0x00fc0801" + register "gen2_dec" = "0x000c0201" + + # Enable "Intel Speed Shift Technology" + register "speed_shift_enable" = "1" + + # Enable DPTF + register "dptf_enable" = "1" + + # FSP Configuration + register "EnableAzalia" = "1" + register "DspEnable" = "1" + register "IoBufferOwnership" = "3" + register "SmbusEnable" = "1" + register "ScsEmmcEnabled" = "1" + register "ScsEmmcHs400Enabled" = "1" + register "ScsSdCardEnabled" = "0" + register "InternalGfx" = "1" + register "SkipExtGfxScan" = "1" + register "Device4Enable" = "1" + register "HeciEnabled" = "0" + register "SaGv" = "3" + register "SerialIrqConfigSirqEnable" = "1" + register "PmConfigSlpS3MinAssert" = "2" # 50ms + register "PmConfigSlpS4MinAssert" = "4" # 4s + register "PmConfigSlpSusMinAssert" = "3" # 4s + register "PmConfigSlpAMinAssert" = "3" # 2s + register "PmTimerDisabled" = "1" + + register "pirqa_routing" = "PCH_IRQ11" + register "pirqb_routing" = "PCH_IRQ10" + register "pirqc_routing" = "PCH_IRQ11" + register "pirqd_routing" = "PCH_IRQ11" + register "pirqe_routing" = "PCH_IRQ11" + register "pirqf_routing" = "PCH_IRQ11" + register "pirqg_routing" = "PCH_IRQ11" + register "pirqh_routing" = "PCH_IRQ11" + + # VR Settings Configuration for 5 Domains + #+----------------+-------+-------+-------------+-------------+-------+ + #| Domain/Setting | SA | IA | Ring Sliced | GT Unsliced | GT | + #+----------------+-------+-------+-------------+-------------+-------+ + #| Psi1Threshold | 20A | 20A | 20A | 20A | 20A | + #| Psi2Threshold | 4A | 5A | 5A | 5A | 5A | + #| Psi3Threshold | 1A | 1A | 1A | 1A | 1A | + #| Psi3Enable | 1 | 1 | 1 | 1 | 1 | + #| Psi4Enable | 1 | 1 | 1 | 1 | 1 | + #| ImonSlope | 0 | 0 | 0 | 0 | 0 | + #| ImonOffset | 0 | 0 | 0 | 0 | 0 | + #| IccMax | 7A | 34A | 34A | 35A | 35A | + #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | 1.52V | + #+----------------+-------+-------+-------------+-------------+-------+ + register "domain_vr_config[VR_SYSTEM_AGENT]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(4), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = VR_CFG_AMP(7), + .voltage_limit = 1520, + }" + + register "domain_vr_config[VR_IA_CORE]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = VR_CFG_AMP(34), + .voltage_limit = 1520, + }" + + register "domain_vr_config[VR_RING]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = VR_CFG_AMP(34), + .voltage_limit = 1520, + }" + + register "domain_vr_config[VR_GT_UNSLICED]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = VR_CFG_AMP(35), + .voltage_limit = 1520, + }" + + register "domain_vr_config[VR_GT_SLICED]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = VR_CFG_AMP(35), + .voltage_limit = 1520, + }" + + # Enable Root port 1 + register "PcieRpEnable[0]" = "1" + # Enable CLKREQ# + register "PcieRpClkReqSupport[0]" = "1" + # RP 1 uses SRCCLKREQ1# + register "PcieRpClkReqNumber[0]" = "1" + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)" # Type-C Port 1 + register "usb2_ports[1]" = "USB2_PORT_MID(OC2)" # Card Reader + register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth + register "usb2_ports[4]" = "USB2_PORT_MID(OC2)" # Type-A Port (board) + register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # PIC MCU + register "usb2_ports[8]" = "USB2_PORT_LONG(OC3)" # Type-A Port (board) + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-C Port 1 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Card Reader + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port (board) + register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port (board) + + register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" # I2C4 is 1.8V + + # Must leave UART0 enabled or SD/eMMC will not work as PCI + register "SerialIoDevMode" = "{ + [PchSerialIoIndexI2C0] = PchSerialIoPci, + [PchSerialIoIndexI2C1] = PchSerialIoPci, + [PchSerialIoIndexI2C2] = PchSerialIoDisabled, + [PchSerialIoIndexI2C3] = PchSerialIoDisabled, + [PchSerialIoIndexI2C4] = PchSerialIoPci, + [PchSerialIoIndexI2C5] = PchSerialIoDisabled, + [PchSerialIoIndexSpi0] = PchSerialIoDisabled, + [PchSerialIoIndexSpi1] = PchSerialIoDisabled, + [PchSerialIoIndexUart0] = PchSerialIoPci, + [PchSerialIoIndexUart1] = PchSerialIoDisabled, + [PchSerialIoIndexUart2] = PchSerialIoSkipInit, + }" + + # PL2 override 25W + register "tdp_pl2_override" = "25" + + # Send an extra VR mailbox command for the PS4 exit issue + register "SendVrMbxCmd" = "2" + + # Lock Down + register "common_soc_config" = "{ + .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, + }" + + device cpu_cluster 0 on + device lapic 0 on end + end + device domain 0 on + device pci 00.0 on end # Host Bridge + device pci 02.0 on end # Integrated Graphics Device + device pci 14.0 on end # USB xHCI + device pci 14.1 off end # USB xDCI (OTG) + device pci 14.2 on end # Thermal Subsystem + device pci 15.0 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + device i2c 10 on end + end + end # I2C #0 + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_B3_IRQ)" + register "wake" = "GPE0_DW0_05" + device i2c 15 on end + end + end # I2C #1 + device pci 15.2 off end # I2C #2 + device pci 15.3 off end # I2C #3 + device pci 16.0 on end # Management Engine Interface 1 + device pci 16.1 off end # Management Engine Interface 2 + device pci 16.2 off end # Management Engine IDE-R + device pci 16.3 off end # Management Engine KT Redirection + device pci 16.4 off end # Management Engine Interface 3 + device pci 17.0 off end # SATA + device pci 19.0 on end # UART #2 + device pci 19.1 off end # I2C #5 + device pci 19.2 on + chip drivers/i2c/nau8825 + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "0" # R389 + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x08" + register "sar_threshold[1]" = "0x12" + register "sar_threshold[2]" = "0x26" + register "sar_threshold[3]" = "0x73" + register "sar_hysteresis" = "0" + register "sar_voltage" = "6" + register "sar_compare_time" = "1" # 1us + register "sar_sampling_time" = "1" # 4us + register "short_key_debounce" = "3" # 30ms + register "jack_insert_debounce" = "7" # 512ms + register "jack_eject_debounce" = "0" + device i2c 1a on end + end + end # I2C #4 + device pci 1c.0 on + chip drivers/intel/wifi + register "wake" = "GPE0_DW0_16" + device pci 00.0 on end + end + end # PCI Express Port 1 + device pci 1c.1 off end # PCI Express Port 2 + device pci 1c.2 off end # PCI Express Port 3 + device pci 1c.3 off end # PCI Express Port 4 + device pci 1c.4 off end # PCI Express Port 5 + device pci 1c.5 off end # PCI Express Port 6 + device pci 1c.6 off end # PCI Express Port 7 + device pci 1c.7 off end # PCI Express Port 8 + device pci 1d.0 off end # PCI Express Port 9 + device pci 1d.1 off end # PCI Express Port 10 + device pci 1d.2 off end # PCI Express Port 11 + device pci 1d.3 off end # PCI Express Port 12 + device pci 1e.0 on end # UART #0 + device pci 1e.1 off end # UART #1 + device pci 1e.2 off end # GSPI #0 + device pci 1e.3 off end # GSPI #1 + device pci 1e.4 on end # eMMC + device pci 1e.5 off end # SDIO + device pci 1e.6 off end # SDCard + device pci 1f.0 on + chip drivers/pc80/tpm + device pnp 0c31.0 on end + end + chip ec/google/chromeec + device pnp 0c09.0 on end + end + end # LPC Interface + device pci 1f.1 on end # P2SB + device pci 1f.2 on end # Power Management Controller + device pci 1f.3 on + chip drivers/generic/max98357a + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)" + register "sdmode_delay" = "5" + device generic 0 on end + end + end # Intel HDA + device pci 1f.4 on end # SMBus + device pci 1f.5 on end # PCH SPI + device pci 1f.6 off end # GbE + end +end |