summaryrefslogtreecommitdiff
path: root/src/mainboard/intel/jarrell/Options.lb
diff options
context:
space:
mode:
Diffstat (limited to 'src/mainboard/intel/jarrell/Options.lb')
-rw-r--r--src/mainboard/intel/jarrell/Options.lb242
1 files changed, 0 insertions, 242 deletions
diff --git a/src/mainboard/intel/jarrell/Options.lb b/src/mainboard/intel/jarrell/Options.lb
deleted file mode 100644
index 91927eee0d..0000000000
--- a/src/mainboard/intel/jarrell/Options.lb
+++ /dev/null
@@ -1,242 +0,0 @@
-uses CONFIG_GENERATE_MP_TABLE
-uses CONFIG_GENERATE_PIRQ_TABLE
-uses CONFIG_USE_FALLBACK_IMAGE
-uses CONFIG_HAVE_FALLBACK_BOOT
-uses CONFIG_HAVE_HARD_RESET
-uses CONFIG_IRQ_SLOT_COUNT
-uses CONFIG_HAVE_OPTION_TABLE
-uses CONFIG_LOGICAL_CPUS
-uses CONFIG_MAX_CPUS
-uses CONFIG_IOAPIC
-uses CONFIG_SMP
-uses CONFIG_FALLBACK_SIZE
-uses CONFIG_ROM_SIZE
-uses CONFIG_ROM_SECTION_SIZE
-uses CONFIG_ROM_IMAGE_SIZE
-uses CONFIG_ROM_SECTION_SIZE
-uses CONFIG_ROM_SECTION_OFFSET
-uses CONFIG_ROM_PAYLOAD
-uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses CONFIG_ROMBASE
-uses CONFIG_XIP_ROM_SIZE
-uses CONFIG_XIP_ROM_BASE
-uses CONFIG_STACK_SIZE
-uses CONFIG_HEAP_SIZE
-uses CONFIG_USE_OPTION_TABLE
-uses CONFIG_LB_CKS_RANGE_START
-uses CONFIG_LB_CKS_RANGE_END
-uses CONFIG_LB_CKS_LOC
-uses CONFIG_MAINBOARD
-uses CONFIG_MAINBOARD_PART_NUMBER
-uses CONFIG_MAINBOARD_VENDOR
-uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
-uses COREBOOT_EXTRA_VERSION
-uses CONFIG_UDELAY_TSC
-uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
-uses CONFIG_RAMBASE
-uses CONFIG_GDB_STUB
-uses CONFIG_CONSOLE_SERIAL8250
-uses CONFIG_TTYS0_BAUD
-uses CONFIG_TTYS0_BASE
-uses CONFIG_TTYS0_LCS
-uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
-uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
-uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-uses CONFIG_CONSOLE_BTEXT
-uses CC
-uses HOSTCC
-uses CONFIG_CROSS_COMPILE
-uses CONFIG_OBJCOPY
-uses CONFIG_MAX_REBOOT_CNT
-uses CONFIG_USE_WATCHDOG_ON_BOOT
-
-
-###
-### Build options
-###
-
-##
-## Because we do the stutter start we need more attempts
-##
-default CONFIG_MAX_REBOOT_CNT=8
-
-##
-## Use the watchdog to break out of a lockup condition
-##
-default CONFIG_USE_WATCHDOG_ON_BOOT=1
-
-##
-## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
-##
-default CONFIG_ROM_SIZE=2097152
-
-
-##
-## Build code for the fallback boot
-##
-default CONFIG_HAVE_FALLBACK_BOOT=1
-
-##
-## Delay timer options
-## Use timer2
-##
-default CONFIG_UDELAY_TSC=1
-default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
-
-##
-## Build code to reset the motherboard from coreboot
-##
-default CONFIG_HAVE_HARD_RESET=1
-
-##
-## Build code to export a programmable irq routing table
-##
-default CONFIG_GENERATE_PIRQ_TABLE=1
-default CONFIG_IRQ_SLOT_COUNT=18
-
-##
-## Build code to export an x86 MP table
-## Useful for specifying IRQ routing values
-##
-default CONFIG_GENERATE_MP_TABLE=1
-
-##
-## Build code to export a CMOS option table
-##
-default CONFIG_HAVE_OPTION_TABLE=1
-
-##
-## Move the default coreboot cmos range off of AMD RTC registers
-##
-default CONFIG_LB_CKS_RANGE_START=49
-default CONFIG_LB_CKS_RANGE_END=122
-default CONFIG_LB_CKS_LOC=123
-
-##
-## Build code for SMP support
-## Only worry about 2 micro processors
-##
-default CONFIG_SMP=1
-default CONFIG_MAX_CPUS=4
-default CONFIG_LOGICAL_CPUS=0
-
-##
-## Build code to setup a generic IOAPIC
-##
-default CONFIG_IOAPIC=1
-
-##
-## Clean up the motherboard id strings
-##
-default CONFIG_MAINBOARD_PART_NUMBER="SE7520JR22D"
-default CONFIG_MAINBOARD_VENDOR= "Intel"
-default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
-default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1079
-#default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3437
-
-###
-### coreboot layout values
-###
-
-## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
-default CONFIG_ROM_IMAGE_SIZE = 65536
-
-##
-## Use a small 8K stack
-##
-default CONFIG_STACK_SIZE=0x2000
-
-##
-## Use a small 32K heap
-##
-default CONFIG_HEAP_SIZE=0x8000
-
-
-###
-### Compute the location and size of where this firmware image
-### (coreboot plus bootloader) will live in the boot rom chip.
-###
-default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE
-
-##
-## Coreboot C code runs at this location in RAM
-##
-default CONFIG_RAMBASE=0x00004000
-
-##
-## Load the payload from the ROM
-##
-default CONFIG_ROM_PAYLOAD=1
-
-
-###
-### Defaults of options that you may want to override in the target config file
-###
-
-##
-## The default compiler
-##
-default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
-default HOSTCC="gcc"
-
-##
-## Disable the gdb stub by default
-##
-default CONFIG_GDB_STUB=0
-
-##
-## The Serial Console
-##
-
-# To Enable the Serial Console
-default CONFIG_CONSOLE_SERIAL8250=1
-
-## Select the serial console baud rate
-default CONFIG_TTYS0_BAUD=115200
-#default CONFIG_TTYS0_BAUD=57600
-#default CONFIG_TTYS0_BAUD=38400
-#default CONFIG_TTYS0_BAUD=19200
-#default CONFIG_TTYS0_BAUD=9600
-#default CONFIG_TTYS0_BAUD=4800
-#default CONFIG_TTYS0_BAUD=2400
-#default CONFIG_TTYS0_BAUD=1200
-
-# Select the serial console base port
-default CONFIG_TTYS0_BASE=0x3f8
-
-# Select the serial protocol
-# This defaults to 8 data bits, 1 stop bit, and no parity
-default CONFIG_TTYS0_LCS=0x3
-
-##
-### Select the coreboot loglevel
-##
-## EMERG 1 system is unusable
-## ALERT 2 action must be taken immediately
-## CRIT 3 critical conditions
-## ERR 4 error conditions
-## WARNING 5 warning conditions
-## NOTICE 6 normal but significant condition
-## INFO 7 informational
-## CONFIG_DEBUG 8 debug-level messages
-## SPEW 9 Way too many details
-
-## Request this level of debugging output
-default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
-## At a maximum only compile in this level of debugging
-default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8
-
-##
-## Select power on after power fail setting
-default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
-
-##
-## Don't enable the btext console
-##
-default CONFIG_CONSOLE_BTEXT=0
-
-
-### End Options.lb
-end