diff options
Diffstat (limited to 'src/mainboard/intel/xe7501devkit/Options.lb')
| -rw-r--r-- | src/mainboard/intel/xe7501devkit/Options.lb | 234 |
1 files changed, 234 insertions, 0 deletions
diff --git a/src/mainboard/intel/xe7501devkit/Options.lb b/src/mainboard/intel/xe7501devkit/Options.lb new file mode 100644 index 0000000000..b034ed6158 --- /dev/null +++ b/src/mainboard/intel/xe7501devkit/Options.lb @@ -0,0 +1,234 @@ +uses HAVE_MP_TABLE
+uses HAVE_ACPI_TABLES
+uses HAVE_PIRQ_TABLE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_OPTION_TABLE
+uses IRQ_SLOT_COUNT
+uses CONFIG_MAX_CPUS
+uses CONFIG_LOGICAL_CPUS
+uses CONFIG_MAX_PHYSICAL_CPUS
+uses CONFIG_IOAPIC
+uses CONFIG_SMP
+uses CONFIG_ROM_STREAM
+uses STACK_SIZE
+uses HEAP_SIZE
+uses USE_OPTION_TABLE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD_PART_NUMBER
+uses MAINBOARD_VENDOR
+uses MAINBOARD
+uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses _RAMBASE
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_CONSOLE_SERIAL8250
+uses CONFIG_UDELAY_TSC
+uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
+uses HAVE_INIT_TIMER
+uses CONFIG_GDB_STUB
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses OBJCOPY
+uses CONFIG_CHIP_NAME
+uses CONFIG_CONSOLE_VGA
+uses CONFIG_PCI_ROM_RUN
+uses DEBUG
+uses CPU_OPT
+uses CONFIG_IDE
+
+## The default definitions are used for these
+uses CONFIG_ROM_STREAM_START
+uses PAYLOAD_SIZE
+
+## These are defined in target Config.lb, don't add here
+uses USE_FALLBACK_IMAGE
+uses ROM_SIZE
+uses ROM_IMAGE_SIZE
+uses FALLBACK_SIZE
+uses LINUXBIOS_EXTRA_VERSION
+
+## These are defined in mainboard Config.lb, don't add here
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses _ROMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+
+###
+### Build options
+###
+
+##
+## Build code for the fallback boot?
+##
+default HAVE_FALLBACK_BOOT=0
+
+
+## Delay timer options
+##
+default CONFIG_UDELAY_TSC=1
+default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=12
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+default HAVE_MP_TABLE=1
+
+## Build code to export ACPI tables?
+default HAVE_ACPI_TABLES=1
+
+##
+## Build code to export a CMOS option table?
+##
+default HAVE_OPTION_TABLE=0
+
+## CMOS checksum definitions (units == bytes)
+## These must match the checksum record in cmos.layout
+default LB_CKS_RANGE_START=128
+default LB_CKS_RANGE_END=130
+default LB_CKS_LOC=131
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+## NOTE: CONFIG_MAX_CPUS is the number of LOGICAL CPUs,
+## so if CONFIG_LOGICAL_CPUS is 1, CONFIG_MAX_CPUS should be 4.
+##
+default CONFIG_SMP=1
+default CONFIG_MAX_CPUS=2
+default CONFIG_LOGICAL_CPUS=0
+default CONFIG_MAX_PHYSICAL_CPUS=2
+
+# VGA Console
+# NOTE: to initialize VGA, need to copy the VGA option ROM from the factory BIOS
+# to VGA.rom
+default CONFIG_CONSOLE_VGA=0
+default CONFIG_PCI_ROM_RUN=0
+
+##
+## Build code to setup a generic IOAPIC
+##
+default CONFIG_IOAPIC=1
+
+##
+## Motherboard identification
+##
+default MAINBOARD_PART_NUMBER="EIDXE7501DEVKIT"
+default MAINBOARD_VENDOR="Intel"
+default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x8086
+default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x2480
+
+###
+### LinuxBIOS layout values
+###
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## CMOS settings not currently supported due to conflicts with factory BIOS
+##
+default USE_OPTION_TABLE = 0
+
+##
+## LinuxBIOS C code runs at this location in RAM
+##
+default _RAMBASE=0x00004000
+
+##
+## Load the payload from the ROM
+##
+default CONFIG_ROM_STREAM = 1
+
+###
+### Defaults of options that you may want to override in the target config file
+###
+
+##
+## The default compiler
+##
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## Disable the gdb stub by default
+##
+default CONFIG_GDB_STUB=0
+
+##
+## The Serial Console
+##
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the linuxBIOS loglevel
+##
+## EMERG 1 system is unusable
+## ALERT 2 action must be taken immediately
+## CRIT 3 critical conditions
+## ERR 4 error conditions
+## WARNING 5 warning conditions
+## NOTICE 6 normal but significant condition
+## INFO 7 informational
+## DEBUG 8 debug-level messages
+## SPEW 9 Way too many details
+
+## Request this level of debugging output
+default DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+default MAXIMUM_CONSOLE_LOGLEVEL=8
+
+##
+## Select power on after power fail setting
+default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+
+## Things we may not have
+default CONFIG_IDE=1
+
+default DEBUG=1
+default CPU_OPT="-g"
+default CONFIG_CHIP_NAME=1
+
+### End Options.lb
+end
|