summaryrefslogtreecommitdiff
path: root/src/mainboard/lippert/toucan-af/mainboard.c
diff options
context:
space:
mode:
Diffstat (limited to 'src/mainboard/lippert/toucan-af/mainboard.c')
-rw-r--r--src/mainboard/lippert/toucan-af/mainboard.c34
1 files changed, 6 insertions, 28 deletions
diff --git a/src/mainboard/lippert/toucan-af/mainboard.c b/src/mainboard/lippert/toucan-af/mainboard.c
index 7647ebee4f..fa5eb41874 100644
--- a/src/mainboard/lippert/toucan-af/mainboard.c
+++ b/src/mainboard/lippert/toucan-af/mainboard.c
@@ -27,33 +27,11 @@
#include "SBPLATFORM.h"
#include "OEM.h" /* SMBUS0_BASE_ADDRESS */
#include <southbridge/amd/cimx/sb800/gpio_oem.h>
-
-/* Write data block to slave on SMBUS0. */
-#define SMB0_STATUS ((SMBUS0_BASE_ADDRESS) + 0)
-#define SMB0_CONTROL ((SMBUS0_BASE_ADDRESS) + 2)
-#define SMB0_HOSTCMD ((SMBUS0_BASE_ADDRESS) + 3)
-#define SMB0_ADDRESS ((SMBUS0_BASE_ADDRESS) + 4)
-#define SMB0_DATA0 ((SMBUS0_BASE_ADDRESS) + 5)
-#define SMB0_BLOCKDATA ((SMBUS0_BASE_ADDRESS) + 7)
-static int smb_write_blk(u8 slave, u8 command, u8 length, const u8 *data)
-{
- __outbyte(SMB0_STATUS, 0x1E); // clear error status
- __outbyte(SMB0_ADDRESS, slave & ~1); // slave addr + direction = out
- __outbyte(SMB0_HOSTCMD, command); // or destination offset
- __outbyte(SMB0_DATA0, length); // sent before data
- __inbyte(SMB0_CONTROL); // reset block data array
- while (length--)
- __outbyte(SMB0_BLOCKDATA, *(data++));
- __outbyte(SMB0_CONTROL, 0x54); // execute block write, no IRQ
-
- while (__inbyte(SMB0_STATUS) == 0x01); // busy, no errors
- return __inbyte(SMB0_STATUS) ^ 0x02; // 0x02 = completed, no errors
-}
+#include "mainboard/lippert/frontrunner-af/sema.h"
static void init(struct device *dev)
{
volatile u8 *spi_base; // base addr of Hudson's SPI host controller
- int i;
printk(BIOS_DEBUG, CONFIG_MAINBOARD_PART_NUMBER " ENTER %s\n", __func__);
/* Init Hudson GPIOs. */
@@ -93,11 +71,11 @@ static void init(struct device *dev)
/* Notify the SMC we're alive and kicking, or after a while it will
* effect a power cycle and switch to the alternate BIOS chip.
- * Should be done as late as possible. */
- printk(BIOS_INFO, "Sending BIOS alive message\n");
- const u8 i_am_alive[] = { 0x03 }; //bit2 = SEL_DP0: 0 = DDI2, 1 = LVDS
- if ((i = smb_write_blk(0x50, 0x25, sizeof(i_am_alive), i_am_alive)))
- printk(BIOS_ERR, "smb_write_blk failed: %d\n", i);
+ * Should be done as late as possible.
+ * Failure here does not matter if watchdog was already disabled,
+ * by configuration or previous boot, so ignore return value.
+ */
+ sema_send_alive();
printk(BIOS_DEBUG, CONFIG_MAINBOARD_PART_NUMBER " EXIT %s\n", __func__);
}