diff options
Diffstat (limited to 'src/mainboard/msi/ms7260/Options.lb')
| -rw-r--r-- | src/mainboard/msi/ms7260/Options.lb | 216 |
1 files changed, 108 insertions, 108 deletions
diff --git a/src/mainboard/msi/ms7260/Options.lb b/src/mainboard/msi/ms7260/Options.lb index b16ebcaf61..9c657d4d0b 100644 --- a/src/mainboard/msi/ms7260/Options.lb +++ b/src/mainboard/msi/ms7260/Options.lb @@ -18,137 +18,137 @@ ## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA ## -uses HAVE_MP_TABLE +uses CONFIG_HAVE_MP_TABLE uses CONFIG_CBFS -uses HAVE_PIRQ_TABLE -uses USE_FALLBACK_IMAGE -uses USE_FAILOVER_IMAGE -uses HAVE_FALLBACK_BOOT -uses HAVE_FAILOVER_BOOT -uses HAVE_HARD_RESET -uses IRQ_SLOT_COUNT -uses HAVE_OPTION_TABLE +uses CONFIG_HAVE_PIRQ_TABLE +uses CONFIG_USE_FALLBACK_IMAGE +uses CONFIG_USE_FAILOVER_IMAGE +uses CONFIG_HAVE_FALLBACK_BOOT +uses CONFIG_HAVE_FAILOVER_BOOT +uses CONFIG_HAVE_HARD_RESET +uses CONFIG_IRQ_SLOT_COUNT +uses CONFIG_HAVE_OPTION_TABLE uses CONFIG_MAX_CPUS uses CONFIG_MAX_PHYSICAL_CPUS uses CONFIG_LOGICAL_CPUS uses CONFIG_IOAPIC uses CONFIG_SMP -uses FALLBACK_SIZE -uses FAILOVER_SIZE -uses ROM_SIZE -uses ROM_SECTION_SIZE -uses ROM_IMAGE_SIZE -uses ROM_SECTION_SIZE -uses ROM_SECTION_OFFSET +uses CONFIG_FALLBACK_SIZE +uses CONFIG_FAILOVER_SIZE +uses CONFIG_ROM_SIZE +uses CONFIG_ROM_SECTION_SIZE +uses CONFIG_ROM_IMAGE_SIZE +uses CONFIG_ROM_SECTION_SIZE +uses CONFIG_ROM_SECTION_OFFSET uses CONFIG_ROM_PAYLOAD uses CONFIG_ROM_PAYLOAD_START uses CONFIG_COMPRESSED_PAYLOAD_NRV2B uses CONFIG_COMPRESSED_PAYLOAD_LZMA uses CONFIG_PRECOMPRESSED_PAYLOAD -uses PAYLOAD_SIZE -uses _ROMBASE -uses XIP_ROM_SIZE -uses XIP_ROM_BASE -uses STACK_SIZE -uses HEAP_SIZE -uses USE_OPTION_TABLE -uses LB_CKS_RANGE_START -uses LB_CKS_RANGE_END -uses LB_CKS_LOC -uses MAINBOARD_PART_NUMBER -uses MAINBOARD_VENDOR -uses MAINBOARD -uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID -uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID +uses CONFIG_PAYLOAD_SIZE +uses CONFIG_ROMBASE +uses CONFIG_XIP_ROM_SIZE +uses CONFIG_XIP_ROM_BASE +uses CONFIG_STACK_SIZE +uses CONFIG_HEAP_SIZE +uses CONFIG_USE_OPTION_TABLE +uses CONFIG_LB_CKS_RANGE_START +uses CONFIG_LB_CKS_RANGE_END +uses CONFIG_LB_CKS_LOC +uses CONFIG_MAINBOARD_PART_NUMBER +uses CONFIG_MAINBOARD_VENDOR +uses CONFIG_MAINBOARD +uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID +uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID uses COREBOOT_EXTRA_VERSION -uses _RAMBASE -uses TTYS0_BAUD -uses TTYS0_BASE -uses TTYS0_LCS -uses DEFAULT_CONSOLE_LOGLEVEL -uses MAXIMUM_CONSOLE_LOGLEVEL -uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL +uses CONFIG_RAMBASE +uses CONFIG_TTYS0_BAUD +uses CONFIG_TTYS0_BASE +uses CONFIG_TTYS0_LCS +uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL +uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL +uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL uses CONFIG_CONSOLE_SERIAL8250 -uses HAVE_INIT_TIMER # ? -uses CROSS_COMPILE +uses CONFIG_HAVE_INIT_TIMER # ? +uses CONFIG_CROSS_COMPILE uses CC -uses HOSTCC -uses OBJCOPY +uses CONFIG_HOSTCC +uses CONFIG_OBJCOPY uses CONFIG_CONSOLE_VGA uses CONFIG_PCI_ROM_RUN uses CONFIG_USBDEBUG_DIRECT -uses HW_MEM_HOLE_SIZEK -uses HW_MEM_HOLE_SIZE_AUTO_INC -uses K8_HT_FREQ_1G_SUPPORT -uses HT_CHAIN_UNITID_BASE -uses HT_CHAIN_END_UNITID_BASE -uses SB_HT_CHAIN_ON_BUS0 -uses SB_HT_CHAIN_UNITID_OFFSET_ONLY -uses USE_DCACHE_RAM -uses DCACHE_RAM_BASE -uses DCACHE_RAM_SIZE -uses DCACHE_RAM_GLOBAL_VAR_SIZE +uses CONFIG_HW_MEM_HOLE_SIZEK +uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC +uses CONFIG_K8_HT_FREQ_1G_SUPPORT +uses CONFIG_HT_CHAIN_UNITID_BASE +uses CONFIG_HT_CHAIN_END_UNITID_BASE +uses CONFIG_SB_HT_CHAIN_ON_BUS0 +uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY +uses CONFIG_USE_DCACHE_RAM +uses CONFIG_DCACHE_RAM_BASE +uses CONFIG_DCACHE_RAM_SIZE +uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE uses CONFIG_USE_INIT -uses SERIAL_CPU_INIT -uses ENABLE_APIC_EXT_ID -uses APIC_ID_OFFSET -uses LIFT_BSP_APIC_ID +uses CONFIG_SERIAL_CPU_INIT +uses CONFIG_ENABLE_APIC_EXT_ID +uses CONFIG_APIC_ID_OFFSET +uses CONFIG_LIFT_BSP_APIC_ID uses CONFIG_PCI_64BIT_PREF_MEM uses CONFIG_LB_MEM_TOPK uses CONFIG_AP_CODE_IN_CAR -uses MEM_TRAIN_SEQ -uses WAIT_BEFORE_CPUS_INIT +uses CONFIG_MEM_TRAIN_SEQ +uses CONFIG_WAIT_BEFORE_CPUS_INIT uses CONFIG_USE_PRINTK_IN_CAR -default ROM_SIZE = 512 * 1024 -default FALLBACK_SIZE = (256 * 1024) - (4 * 1024) -default FAILOVER_SIZE = 4 * 1024 +default CONFIG_ROM_SIZE = 512 * 1024 +default CONFIG_FALLBACK_SIZE = (256 * 1024) - (4 * 1024) +default CONFIG_FAILOVER_SIZE = 4 * 1024 default CONFIG_LB_MEM_TOPK = 2048 # 1MB more for pgtbl. -default HAVE_FALLBACK_BOOT = 1 -default HAVE_FAILOVER_BOOT = 1 -default HAVE_HARD_RESET = 1 -default HAVE_PIRQ_TABLE = 1 -default IRQ_SLOT_COUNT = 11 # TODO: Check if correct. -default HAVE_MP_TABLE = 1 # TODO: Check if correct. -default HAVE_OPTION_TABLE = 1 +default CONFIG_HAVE_FALLBACK_BOOT = 1 +default CONFIG_HAVE_FAILOVER_BOOT = 1 +default CONFIG_HAVE_HARD_RESET = 1 +default CONFIG_HAVE_PIRQ_TABLE = 1 +default CONFIG_IRQ_SLOT_COUNT = 11 # TODO: Check if correct. +default CONFIG_HAVE_MP_TABLE = 1 # TODO: Check if correct. +default CONFIG_HAVE_OPTION_TABLE = 1 default CONFIG_SMP = 1 default CONFIG_MAX_CPUS = 2 default CONFIG_MAX_PHYSICAL_CPUS = 1 default CONFIG_LOGICAL_CPUS = 1 -# default SERIAL_CPU_INIT = 0 -default ENABLE_APIC_EXT_ID = 0 -default APIC_ID_OFFSET = 0x10 -default LIFT_BSP_APIC_ID = 1 +# default CONFIG_SERIAL_CPU_INIT = 0 +default CONFIG_ENABLE_APIC_EXT_ID = 0 +default CONFIG_APIC_ID_OFFSET = 0x10 +default CONFIG_LIFT_BSP_APIC_ID = 1 # Move the default coreboot CMOS range off of AMD RTC registers. -default LB_CKS_RANGE_START = 49 -default LB_CKS_RANGE_END = 122 -default LB_CKS_LOC = 123 +default CONFIG_LB_CKS_RANGE_START = 49 +default CONFIG_LB_CKS_RANGE_END = 122 +default CONFIG_LB_CKS_LOC = 123 # Memory hole size. 0 means disable, others will enable the hole. In that # case, if it is smaller than mmio_basek, it will use mmio_basek instead. -# default HW_MEM_HOLE_SIZEK = 0x200000 # 2GB -default HW_MEM_HOLE_SIZEK = 0x100000 # 1GB -# default HW_MEM_HOLE_SIZEK = 0x80000 # 512MB +# default CONFIG_HW_MEM_HOLE_SIZEK = 0x200000 # 2GB +default CONFIG_HW_MEM_HOLE_SIZEK = 0x100000 # 1GB +# default CONFIG_HW_MEM_HOLE_SIZEK = 0x80000 # 512MB # Make auto increase hole size to avoid hole_startk equal to basek so as # to make some kernel happy. -# default HW_MEM_HOLE_SIZE_AUTO_INC = 1 +# default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC = 1 # Opteron K8 1G HT support. -default K8_HT_FREQ_1G_SUPPORT = 1 +default CONFIG_K8_HT_FREQ_1G_SUPPORT = 1 # HT Unit ID offset, default is 1, the typical one, 0 means only one HT device. -default HT_CHAIN_UNITID_BASE = 0 +default CONFIG_HT_CHAIN_UNITID_BASE = 0 # Real SB Unit ID, default is 0x20, mean don't touch it at last. -# default HT_CHAIN_END_UNITID_BASE = 0x6 +# default CONFIG_HT_CHAIN_END_UNITID_BASE = 0x6 # Make the SB HT chain on bus 0, default is not (0). -default SB_HT_CHAIN_ON_BUS0 = 2 +default CONFIG_SB_HT_CHAIN_ON_BUS0 = 2 # Only offset for SB chain? Default is yes (1). -default SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0 +default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0 # Allow capable device use that above 4GB. # default CONFIG_PCI_64BIT_PREF_MEM = 1 @@ -156,35 +156,35 @@ default SB_HT_CHAIN_UNITID_OFFSET_ONLY = 0 default CONFIG_CONSOLE_VGA = 1 # Needed for VGA. default CONFIG_PCI_ROM_RUN = 1 # Needed for VGA. default CONFIG_USBDEBUG_DIRECT = 0 -default USE_DCACHE_RAM = 1 -default DCACHE_RAM_BASE = 0xc8000 -default DCACHE_RAM_SIZE = 0x08000 -default DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000 +default CONFIG_USE_DCACHE_RAM = 1 +default CONFIG_DCACHE_RAM_BASE = 0xc8000 +default CONFIG_DCACHE_RAM_SIZE = 0x08000 +default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE = 0x01000 default CONFIG_USE_INIT = 0 default CONFIG_AP_CODE_IN_CAR = 0 -default MEM_TRAIN_SEQ = 2 -default WAIT_BEFORE_CPUS_INIT = 0 +default CONFIG_MEM_TRAIN_SEQ = 2 +default CONFIG_WAIT_BEFORE_CPUS_INIT = 0 default CONFIG_IOAPIC = 1 -default MAINBOARD_PART_NUMBER = "K9N Neo (MS-7260)" -default MAINBOARD_VENDOR = "MSI" -default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462 -default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x7260 -default ROM_IMAGE_SIZE = 65536 -default STACK_SIZE = 0x2000 -default HEAP_SIZE = 0x8000 -default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE) -default _RAMBASE = 0x00100000 +default CONFIG_MAINBOARD_PART_NUMBER = "K9N Neo (MS-7260)" +default CONFIG_MAINBOARD_VENDOR = "MSI" +default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID = 0x1462 +default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID = 0x7260 +default CONFIG_ROM_IMAGE_SIZE = 65536 +default CONFIG_STACK_SIZE = 0x2000 +default CONFIG_HEAP_SIZE = 0x8000 +default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE) +default CONFIG_RAMBASE = 0x00100000 default CONFIG_ROM_PAYLOAD = 1 -default CC = "$(CROSS_COMPILE)gcc -m32" -default HOSTCC = "gcc" +default CC = "$(CONFIG_CROSS_COMPILE)gcc -m32" +default CONFIG_HOSTCC = "gcc" default CONFIG_USE_PRINTK_IN_CAR = 1 default CONFIG_CONSOLE_SERIAL8250 = 1 -default TTYS0_BAUD = 115200 -default TTYS0_BASE = 0x3f8 -default TTYS0_LCS = 0x3 -default DEFAULT_CONSOLE_LOGLEVEL = 9 -default MAXIMUM_CONSOLE_LOGLEVEL = 9 -default MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON" +default CONFIG_TTYS0_BAUD = 115200 +default CONFIG_TTYS0_BASE = 0x3f8 +default CONFIG_TTYS0_LCS = 0x3 +default CONFIG_DEFAULT_CONSOLE_LOGLEVEL = 9 +default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL = 9 +default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL = "MAINBOARD_POWER_ON" # # CBFS |