diff options
Diffstat (limited to 'src/mainboard/siemens/mc_apl1/variants/mc_apl5/mainboard.c')
-rw-r--r-- | src/mainboard/siemens/mc_apl1/variants/mc_apl5/mainboard.c | 110 |
1 files changed, 110 insertions, 0 deletions
diff --git a/src/mainboard/siemens/mc_apl1/variants/mc_apl5/mainboard.c b/src/mainboard/siemens/mc_apl1/variants/mc_apl5/mainboard.c new file mode 100644 index 0000000000..6d22fd9826 --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/variants/mc_apl5/mainboard.c @@ -0,0 +1,110 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2018 Siemens AG + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <bootstate.h> +#include <console/console.h> +#include <device/pci_ids.h> +#include <device/pci_ops.h> +#include <gpio.h> +#include <hwilib.h> +#include <intelblocks/lpc_lib.h> +#include <intelblocks/pcr.h> +#include <soc/pcr_ids.h> +#include <timer.h> +#include <timestamp.h> +#include <baseboard/variants.h> +#include <variant/ptn3460.h> + +#define TX_DWORD3 0xa8c + +void variant_mainboard_final(void) +{ + int status; + struct device *dev = NULL; + + /* + * Set up the DP2LVDS converter. + * ptn3460_init() may only be executed after i2c bus init. + */ + status = ptn3460_init("hwinfo.hex"); + if (status) + printk(BIOS_ERR, "LCD: Set up PTN with status 0x%x\n", status); + else + printk(BIOS_INFO, "LCD: Set up PTN was successful.\n"); + + /* + * PIR6 register mapping for PCIe root ports + * INTA#->PIRQB#, INTB#->PIRQC#, INTC#->PIRQD#, INTD#-> PIRQA# + */ + pcr_write16(PID_ITSS, 0x314c, 0x0321); + + /* Disable clock outputs 1-5 (CLKOUT) for XIO2001 PCIe to PCI Bridge. */ + dev = dev_find_device(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_XIO2001, 0); + if (dev) + pci_write_config8(dev, 0xd8, 0x3e); + + /* Enable CLKRUN_EN for power gating LPC */ + lpc_enable_pci_clk_cntl(); + + /* + * Enable LPC PCE (Power Control Enable) by setting IOSF-SB port 0xD2 + * offset 0x341D bit3 and bit0. + * Enable LPC CCE (Clock Control Enable) by setting IOSF-SB port 0xD2 + * offset 0x341C bit [3:0]. + */ + pcr_or32(PID_LPC, PCR_LPC_PRC, (PCR_LPC_CCE_EN | PCR_LPC_PCE_EN)); + + /* + * Correct the SATA transmit signal via the High Speed I/O Transmit + * Control Register 3. + * Bit [23:16] set the output voltage swing for TX line. + * The value 0x4a sets the swing level to 0.58 V. + */ + pcr_rmw32(PID_MODPHY, TX_DWORD3, (0x00 << 16), (0x4a << 16)); +} + +static void wait_for_legacy_dev(void *unused) +{ + uint32_t legacy_delay, us_since_boot; + struct stopwatch sw; + + /* Open main hwinfo block. */ + if (hwilib_find_blocks("hwinfo.hex") != CB_SUCCESS) + return; + + /* Get legacy delay parameter from hwinfo. */ + if (hwilib_get_field(LegacyDelay, (uint8_t *) &legacy_delay, + sizeof(legacy_delay)) != sizeof(legacy_delay)) + return; + + us_since_boot = get_us_since_boot(); + /* No need to wait if the time since boot is already long enough.*/ + if (us_since_boot > legacy_delay) + return; + stopwatch_init_msecs_expire(&sw, (legacy_delay - us_since_boot) / 1000); + printk(BIOS_NOTICE, "Wait remaining %d of %d us for legacy devices...", + legacy_delay - us_since_boot, legacy_delay); + stopwatch_wait_until_expired(&sw); + printk(BIOS_NOTICE, "done!\n"); +} + +static void finalize_boot(void *unused) +{ + /* Set coreboot ready LED. */ + gpio_output(CNV_RGI_DT, 1); +} + +BOOT_STATE_INIT_ENTRY(BS_DEV_ENUMERATE, BS_ON_ENTRY, wait_for_legacy_dev, NULL); +BOOT_STATE_INIT_ENTRY(BS_PAYLOAD_BOOT, BS_ON_ENTRY, finalize_boot, NULL); |