diff options
Diffstat (limited to 'src/mainboard/siemens/mc_apl1')
-rw-r--r-- | src/mainboard/siemens/mc_apl1/Kconfig | 17 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/Kconfig.name | 2 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/Makefile.inc | 3 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/acpi_tables.c | 3 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/board_info.txt | 4 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/bootblock.c | 22 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/brd_gpio.h | 62 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/devicetree.cb | 226 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/dsdt.asl | 42 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/mainboard.c | 25 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/mc_apl1.fmd | 40 | ||||
-rw-r--r-- | src/mainboard/siemens/mc_apl1/romstage.c | 119 |
12 files changed, 565 insertions, 0 deletions
diff --git a/src/mainboard/siemens/mc_apl1/Kconfig b/src/mainboard/siemens/mc_apl1/Kconfig new file mode 100644 index 0000000000..6201ed3664 --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/Kconfig @@ -0,0 +1,17 @@ +if BOARD_SIEMENS_MC_APL1 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select SOC_INTEL_APOLLOLAKE + select BOARD_ROMSIZE_KB_16384 + select HAVE_ACPI_TABLES + +config MAINBOARD_DIR + string + default siemens/mc_apl1 + +config MAINBOARD_PART_NUMBER + string + default "MC APL1" + +endif # BOARD_SIEMENS_MC_APL1 diff --git a/src/mainboard/siemens/mc_apl1/Kconfig.name b/src/mainboard/siemens/mc_apl1/Kconfig.name new file mode 100644 index 0000000000..bbc2a82eaa --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/Kconfig.name @@ -0,0 +1,2 @@ +config BOARD_SIEMENS_MC_APL1 + bool "MC APL1" diff --git a/src/mainboard/siemens/mc_apl1/Makefile.inc b/src/mainboard/siemens/mc_apl1/Makefile.inc new file mode 100644 index 0000000000..9e3e892f66 --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/Makefile.inc @@ -0,0 +1,3 @@ +bootblock-y += bootblock.c + +ramstage-y += mainboard.c diff --git a/src/mainboard/siemens/mc_apl1/acpi_tables.c b/src/mainboard/siemens/mc_apl1/acpi_tables.c new file mode 100644 index 0000000000..e06f6a648d --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/acpi_tables.c @@ -0,0 +1,3 @@ +/* + * Blank file required by build system assumptions of this file being present. + */ diff --git a/src/mainboard/siemens/mc_apl1/board_info.txt b/src/mainboard/siemens/mc_apl1/board_info.txt new file mode 100644 index 0000000000..01963ecd6c --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/board_info.txt @@ -0,0 +1,4 @@ +Board name: MC APL1 +Category: misc +ROM protocol: SPI +ROM socketed: no diff --git a/src/mainboard/siemens/mc_apl1/bootblock.c b/src/mainboard/siemens/mc_apl1/bootblock.c new file mode 100644 index 0000000000..3de44a8ff3 --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/bootblock.c @@ -0,0 +1,22 @@ +/* + * This file is part of the coreboot project. + * + * Copyright 2016 Google Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <bootblock_common.h> +#include <soc/lpc.h> + +void bootblock_mainboard_init(void) +{ + lpc_configure_pads(); +} diff --git a/src/mainboard/siemens/mc_apl1/brd_gpio.h b/src/mainboard/siemens/mc_apl1/brd_gpio.h new file mode 100644 index 0000000000..33b839bbca --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/brd_gpio.h @@ -0,0 +1,62 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2015-2016 Intel Corporation. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <soc/gpio.h> + +#if ENV_ROMSTAGE + +static const struct pad_config gpio_table[] = { + PAD_CFG_NF(GPIO_134, NATIVE, DEEP, NF2), /* ISH_I2C0_SDA/IO-OD */ + PAD_CFG_NF(GPIO_135, NATIVE, DEEP, NF2), /* ISH_I2C0_SCL/IO-OD */ + PAD_CFG_NF(GPIO_136, NATIVE, DEEP, NF2), /* ISH_I2C1_SDA/IO-OD */ + PAD_CFG_NF(GPIO_137, NATIVE, DEEP, NF2), /* ISH_I2C1_SCL/IO-OD */ + + PAD_CFG_NF(GPIO_0, NATIVE, DEEP, NF1), + PAD_CFG_NF(GPIO_1, NATIVE, DEEP, NF1), + PAD_CFG_NF(GPIO_2, NATIVE, DEEP, NF1), + PAD_CFG_NF(GPIO_3, NATIVE, DEEP, NF1), + PAD_CFG_NF(GPIO_4, NATIVE, DEEP, NF1), + PAD_CFG_NF(GPIO_5, NATIVE, DEEP, NF1), + PAD_CFG_NF(GPIO_6, NATIVE, DEEP, NF1), + PAD_CFG_NF(GPIO_7, NATIVE, DEEP, NF1), + PAD_CFG_NF(GPIO_8, NATIVE, DEEP, NF1), + + /* EXP_I2C_SDA and I2C_PSS_SDA and I2C_2_SDA_IOEXP */ + PAD_CFG_NF(GPIO_7, NATIVE, DEEP, NF1), + /* EXP_I2C_SCL and I2C_PSS_SCL and I2C_2_SCL_IOEXP */ + PAD_CFG_NF(GPIO_8, NATIVE, DEEP, NF1), + + PAD_CFG_GPO(GPIO_152, 0, DEEP), /* PERST# */ + PAD_CFG_GPO(GPIO_19, 1, DEEP), /* PFET */ + PAD_CFG_GPO(GPIO_13, 0, DEEP), /* PERST# */ + PAD_CFG_GPO(GPIO_17, 1, DEEP), /* PFET */ + PAD_CFG_GPO(GPIO_15, 0, DEEP), /* PERST# */ + + PAD_CFG_NF(GPIO_210, NATIVE, DEEP, NF1), /* CLKREQ# */ + + PAD_CFG_NF(SMB_CLK, NATIVE, DEEP, NF1), + PAD_CFG_NF(SMB_DATA, NATIVE, DEEP, NF1), + PAD_CFG_NF(LPC_ILB_SERIRQ, NATIVE, DEEP, NF1), + PAD_CFG_NF(LPC_CLKOUT0, NATIVE, DEEP, NF1), + PAD_CFG_NF(LPC_CLKOUT1, NATIVE, DEEP, NF1), + PAD_CFG_NF(LPC_AD0, NATIVE, DEEP, NF1), + PAD_CFG_NF(LPC_AD1, NATIVE, DEEP, NF1), + PAD_CFG_NF(LPC_AD2, NATIVE, DEEP, NF1), + PAD_CFG_NF(LPC_AD3, NATIVE, DEEP, NF1), + PAD_CFG_NF(LPC_CLKRUNB, NATIVE, DEEP, NF1), + PAD_CFG_NF(LPC_FRAMEB, NATIVE, DEEP, NF1), +}; + +#endif diff --git a/src/mainboard/siemens/mc_apl1/devicetree.cb b/src/mainboard/siemens/mc_apl1/devicetree.cb new file mode 100644 index 0000000000..ce01a8b82b --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/devicetree.cb @@ -0,0 +1,226 @@ +chip soc/intel/apollolake + + device cpu_cluster 0 on + device lapic 0 on end + end + + register "pcie_rp0_clkreq_pin" = "0" # wifi/bt + # Disable unused clkreq of PCIe root ports + register "pcie_rp1_clkreq_pin" = "CLKREQ_DISABLED" + register "pcie_rp2_clkreq_pin" = "CLKREQ_DISABLED" + register "pcie_rp3_clkreq_pin" = "CLKREQ_DISABLED" + register "pcie_rp4_clkreq_pin" = "CLKREQ_DISABLED" + register "pcie_rp5_clkreq_pin" = "CLKREQ_DISABLED" + + # GPIO for PERST_0 + # If the Board has PERST_0 signal, assign the GPIO + # If the Board does not have PERST_0, assign GPIO_PRT0_UDEF + register "prt0_gpio" = "GPIO_122" + + # EMMC TX DATA Delay 1 + # Refer to EDS-Vol2-22.3. + # [14:8] steps of delay for HS400, each 125ps. + # [6:0] steps of delay for SDR104/HS200, each 125ps. + register "emmc_tx_data_cntl1" = "0x0C16" + + # EMMC TX DATA Delay 2 + # Refer to EDS-Vol2-22.3. + # [30:24] steps of delay for SDR50, each 125ps. + # [22:16] steps of delay for DDR50, each 125ps. + # [14:8] steps of delay for SDR25/HS50, each 125ps. + # [6:0] steps of delay for SDR12, each 125ps. + register "emmc_tx_data_cntl2" = "0x28162828" + + # EMMC RX CMD/DATA Delay 1 + # Refer to EDS-Vol2-22.3. + # [30:24] steps of delay for SDR50, each 125ps. + # [22:16] steps of delay for DDR50, each 125ps. + # [14:8] steps of delay for SDR25/HS50, each 125ps. + # [6:0] steps of delay for SDR12, each 125ps. + register "emmc_rx_cmd_data_cntl1" = "0x00181717" + + # EMMC RX CMD/DATA Delay 2 + # Refer to EDS-Vol2-22.3. + # [17:16] stands for Rx Clock before Output Buffer + # [14:8] steps of delay for Auto Tuning Mode, each 125ps. + # [6:0] steps of delay for HS200, each 125ps. + register "emmc_rx_cmd_data_cntl2" = "0x10008" + + # Enable DPTF + register "dptf_enable" = "1" + + # PL1 override 12000 mW: the energy calculation is wrong with the + # current VR solution. Experiments show that SoC TDP max (6W) can + # be reached when RAPL PL1 is set to 12W. + register "tdp_pl1_override_mw" = "12000" + # Set RAPL PL2 to 15W. + register "tdp_pl2_override_mw" = "15000" + + # Enable Audio Clock and Power gating + register "hdaudio_clk_gate_enable" = "1" + register "hdaudio_pwr_gate_enable" = "1" + register "hdaudio_bios_config_lockdown" = "1" + + # Enable lpss s0ix + register "lpss_s0ix_enable" = "1" + + # GPE configuration + # Note that GPE events called out in ASL code rely on this + # route, i.e., if this route changes then the affected GPE + # offset bits also need to be changed. This sets the PMC register + # GPE_CFG fields. + register "gpe0_dw1" = "PMC_GPE_N_31_0" + register "gpe0_dw2" = "PMC_GPE_N_63_32" + register "gpe0_dw3" = "PMC_GPE_SW_31_0" + + # Enable I2C0 for audio codec at 400kHz + register "i2c[0]" = "{ + .speed = I2C_SPEED_FAST, + .rise_time_ns = 104, + .fall_time_ns = 52, + }" + + # Enable I2C2 bus early for TPM at 400kHz + register "i2c[2]" = "{ + .early_init = 1, + .speed = I2C_SPEED_FAST, + .rise_time_ns = 57, + .fall_time_ns = 28, + }" + + # touchscreen at 400kHz + register "i2c[3]" = "{ + .speed = I2C_SPEED_FAST, + .rise_time_ns = 76, + .fall_time_ns = 164, + }" + + # trackpad at 400kHz + register "i2c[4]" = "{ + .speed = I2C_SPEED_FAST, + .rise_time_ns = 114, + .fall_time_ns = 164, + }" + + # digitizer at 400kHz + register "i2c[5]" = "{ + .speed = I2C_SPEED_FAST, + .rise_time_ns = 152, + .fall_time_ns = 30, + }" + + # Minimum SLP S3 assertion width 28ms. + register "slp_s3_assertion_width_usecs" = "28000" + + device domain 0 on + device pci 00.0 on end # - Host Bridge + device pci 00.1 on end # - DPTF + device pci 00.2 on end # - NPK + device pci 02.0 on end # - Gen + device pci 03.0 on end # - Iunit + device pci 0d.0 on end # - P2SB + device pci 0d.1 on end # - PMC + device pci 0d.2 on end # - SPI + device pci 0d.3 on end # - Shared SRAM + device pci 0e.0 on # - Audio + chip drivers/generic/max98357a + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_76)" + register "sdmode_delay" = "5" + device generic 0 on end + end + end + device pci 11.0 off end # - ISH + device pci 12.0 off end # - SATA + device pci 13.0 off end # - Root Port 2 - PCIe-A 0 + device pci 13.1 off end # - Root Port 3 - PCIe-A 1 + device pci 13.2 off end # - Root Port 4 - PCIe-A 2 + device pci 13.3 off end # - Root Port 5 - PCIe-A 3 + device pci 14.0 on + chip drivers/intel/wifi + register "wake" = "GPE0_DW3_00" + device pci 00.0 on end + end + end # - Root Port 0 - PCIe-B 0 - Wifi + device pci 14.1 off end # - Root Port 1 - PCIe-B 1 + device pci 15.0 on end # - XHCI + device pci 15.1 off end # - XDCI + device pci 16.0 on # - I2C 0 + chip drivers/i2c/da7219 + register "irq" = "IRQ_LEVEL_LOW(GPIO_116_IRQ)" + register "btn_cfg" = "50" + register "mic_det_thr" = "500" + register "jack_ins_deb" = "20" + register "jack_det_rate" = ""32ms_64ms"" + register "jack_rem_deb" = "1" + register "a_d_btn_thr" = "0xa" + register "d_b_btn_thr" = "0x16" + register "b_c_btn_thr" = "0x21" + register "c_mic_btn_thr" = "0x3e" + register "btn_avg" = "4" + register "adc_1bit_rpt" = "1" + register "micbias_lvl" = "2600" + register "mic_amp_in_sel" = ""diff"" + device i2c 1a on end + end + end + device pci 16.1 on end # - I2C 1 + device pci 16.2 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "IRQ_EDGE_LOW(GPIO_28_IRQ)" + device i2c 50 on end + end + end # - I2C 2 + device pci 16.3 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "IRQ_EDGE_LOW(GPIO_21_IRQ)" + register "probed" = "1" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_36)" + register "reset_delay_ms" = "20" + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_152)" + register "enable_delay_ms" = "1" + register "has_power_resource" = "1" + device i2c 10 on end + end + end # - I2C 3 + device pci 17.0 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "IRQ_EDGE_LOW(GPIO_18_IRQ)" + register "wake" = "GPE0_DW1_15" + register "probed" = "1" + device i2c 15 on end + end + end # - I2C 4 + device pci 17.1 on + chip drivers/i2c/wacom + register "generic" = "{ + .hid = WCOM50C1_HID, + .cid = PNP0C50_CID, + .desc = WCOM_DT_DESC, + .irq = IRQ_LEVEL_LOW(GPIO_13_IRQ), + }" + register "hid_desc_reg_offset" = "0x1" + device i2c 0x9 on end + end + end # - I2C 5 + device pci 17.2 off end # - I2C 6 + device pci 17.3 off end # - I2C 7 + device pci 18.0 on end # - UART 0 + device pci 18.1 on end # - UART 1 + device pci 18.2 on end # - UART 2 + device pci 18.3 off end # - UART 3 + device pci 19.0 on end # - SPI 0 + device pci 19.1 off end # - SPI 1 + device pci 19.2 off end # - SPI 2 + device pci 1a.0 on end # - PWM + device pci 1b.0 on end # - SDCARD + device pci 1c.0 on end # - eMMC + device pci 1e.0 off end # - SDIO + device pci 1f.0 on end # - LPC + device pci 1f.1 on end # - SMBUS + end +end diff --git a/src/mainboard/siemens/mc_apl1/dsdt.asl b/src/mainboard/siemens/mc_apl1/dsdt.asl new file mode 100644 index 0000000000..004523a0ff --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/dsdt.asl @@ -0,0 +1,42 @@ +/* + * This file is part of the coreboot project. + * + * Copyright 2016 Google Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +DefinitionBlock( + "dsdt.aml", + "DSDT", + 0x05, // DSDT revision: ACPI v5.0 + "COREv4", // OEM id + "COREBOOT", // OEM table id + 0x20110725 // OEM revision +) +{ + /* global NVS and variables */ + #include <soc/intel/apollolake/acpi/globalnvs.asl> + + /* CPU */ + #include <soc/intel/apollolake/acpi/cpu.asl> + + Scope (\_SB) { + Device (PCI0) + { + #include <soc/intel/apollolake/acpi/northbridge.asl> + #include <soc/intel/apollolake/acpi/southbridge.asl> + #include <soc/intel/apollolake/acpi/pch_hda.asl> + } + } + + /* Chipset specific sleep states */ + #include <soc/intel/apollolake/acpi/sleepstates.asl> +} diff --git a/src/mainboard/siemens/mc_apl1/mainboard.c b/src/mainboard/siemens/mc_apl1/mainboard.c new file mode 100644 index 0000000000..f7a2ef1c99 --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/mainboard.c @@ -0,0 +1,25 @@ +/* + * This file is part of the coreboot project. + * + * Copyright 2016 Google Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <device/device.h> + +static void mainboard_init(void *chip_info) +{ + /* Nothing Here Yet */ +} + +struct chip_operations mainboard_ops = { + .init = mainboard_init, +}; diff --git a/src/mainboard/siemens/mc_apl1/mc_apl1.fmd b/src/mainboard/siemens/mc_apl1/mc_apl1.fmd new file mode 100644 index 0000000000..3da8467431 --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/mc_apl1.fmd @@ -0,0 +1,40 @@ +FLASH 16M { + WP_RO@0x0 0x400000 { + SI_DESC@0x0 0x1000 + IFWI@0x1000 0x1ff000 + RO_VPD@0x200000 0x4000 + RO_SECTION@0x204000 0x1fc000 { + FMAP@0x0 0x800 + COREBOOT(CBFS)@0x1000 0x1bb000 + RO_UNUSED@0x1bc000 0x40000 + } + } + MISC_RW@0x400000 0x30000 { + UNIFIED_MRC_CACHE@0x0 0x21000 { + RECOVERY_MRC_CACHE@0x0 0x10000 + RW_MRC_CACHE@0x10000 0x10000 + RW_VAR_MRC_CACHE@0x20000 0x1000 + } + RW_ELOG@0x21000 0x3000 + RW_SHARED@0x24000 0x4000 { + SHARED_DATA@0x0 0x2000 + VBLOCK_DEV@0x2000 0x2000 + } + RW_VPD@0x28000 0x2000 + RW_NVRAM@0x2a000 0x6000 + } + RW_LEGACY(CBFS)@0xd30000 0x200000 + BIOS_UNUSABLE@0xf30000 0x4f000 + DEVICE_EXTENSION@0xf7f000 0x80000 + # Currently, it is required that the BIOS region be a multiple of 8KiB. + # This is required so that the recovery mechanism can find SIGN_CSE + # region aligned to 4K at the center of BIOS region. Since the + # descriptor at the beginning uses 4K and BIOS starts at an offset of + # 4K, a hole of 4K is created towards the end of the flash to compensate + # for the size requirement of BIOS region. + # FIT tool thus creates descriptor with following regions: + # Descriptor --> 0 to 4K + # BIOS --> 4K to 0xf7f000 + # Device ext --> 0xf7f000 to 0xfff000 + UNUSED_HOLE@0xfff000 0x1000 +} diff --git a/src/mainboard/siemens/mc_apl1/romstage.c b/src/mainboard/siemens/mc_apl1/romstage.c new file mode 100644 index 0000000000..5c784ba629 --- /dev/null +++ b/src/mainboard/siemens/mc_apl1/romstage.c @@ -0,0 +1,119 @@ +/* + * This file is part of the coreboot project. + * + * Copyright 2016 Google Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <string.h> +#include <soc/romstage.h> +#include <fsp/api.h> +#include <FspmUpd.h> +#include "brd_gpio.h" + +static const uint8_t Ch0_Bit_swizzling[] = { + 0x09, 0x0e, 0x0c, 0x0d, 0x0a, 0x0b, 0x08, 0x0f, + 0x05, 0x06, 0x01, 0x00, 0x02, 0x07, 0x04, 0x03, + 0x1a, 0x1f, 0x1c, 0x1b, 0x1d, 0x19, 0x18, 0x1e, + 0x14, 0x16, 0x17, 0x11, 0x12, 0x13, 0x10, 0x15 +}; +static const uint8_t Ch1_Bit_swizzling[] = { + 0x06, 0x07, 0x05, 0x04, 0x03, 0x01, 0x00, 0x02, + 0x0c, 0x0a, 0x0b, 0x0d, 0x0e, 0x08, 0x09, 0x0f, + 0x14, 0x10, 0x16, 0x15, 0x12, 0x11, 0x13, 0x17, + 0x1e, 0x1c, 0x1d, 0x19, 0x18, 0x1a, 0x1b, 0x1f +}; +static const uint8_t Ch2_Bit_swizzling[] = { + 0x0f, 0x09, 0x08, 0x0b, 0x0c, 0x0d, 0x0e, 0x0a, + 0x05, 0x02, 0x00, 0x03, 0x06, 0x07, 0x01, 0x04, + 0x19, 0x1c, 0x1e, 0x1f, 0x1a, 0x1b, 0x18, 0x1d, + 0x14, 0x17, 0x16, 0x15, 0x12, 0x13, 0x10, 0x11 +}; +static const uint8_t Ch3_Bit_swizzling[] = { + 0x03, 0x04, 0x06, 0x05, 0x00, 0x01, 0x02, 0x07, + 0x0b, 0x0a, 0x08, 0x09, 0x0e, 0x0c, 0x0f, 0x0d, + 0x11, 0x17, 0x13, 0x10, 0x15, 0x16, 0x14, 0x12, + 0x1c, 0x1d, 0x1a, 0x19, 0x1e, 0x1b, 0x18, 0x1f +}; + +void mainboard_memory_init_params(FSPM_UPD *memupd) +{ + /* setup early gpio before memory */ + gpio_configure_pads(gpio_table, ARRAY_SIZE(gpio_table)); + + /* DRAM Config settings */ + memupd->FspmConfig.Package = 0x1; + memupd->FspmConfig.Profile = 0xB; + memupd->FspmConfig.MemoryDown = 0x1; + memupd->FspmConfig.DDR3LPageSize = 0x0; + memupd->FspmConfig.DDR3LASR = 0x0; + memupd->FspmConfig.ScramblerSupport = 0x1; + memupd->FspmConfig.ChannelHashMask = 0x36; + memupd->FspmConfig.SliceHashMask = 0x9; + memupd->FspmConfig.InterleavedMode = 0x2; + memupd->FspmConfig.ChannelsSlicesEnable = 0x0; + memupd->FspmConfig.MinRefRate2xEnable = 0x0; + memupd->FspmConfig.DualRankSupportEnable = 0x1; + memupd->FspmConfig.RmtMode = 0x0; + memupd->FspmConfig.MemorySizeLimit = 0x1800; + memupd->FspmConfig.LowMemoryMaxValue = 0x0; + memupd->FspmConfig.DisableFastBoot = 0x0; + memupd->FspmConfig.HighMemoryMaxValue = 0x0; + memupd->FspmConfig.DIMM0SPDAddress = 0x0; + memupd->FspmConfig.DIMM1SPDAddress = 0x0; + memupd->FspmConfig.Ch0_RankEnable = 0x3; + memupd->FspmConfig.Ch0_DeviceWidth = 0x1; + memupd->FspmConfig.Ch0_DramDensity = 0x2; + memupd->FspmConfig.Ch0_Option = 0x3; + memupd->FspmConfig.Ch0_OdtConfig = 0x0; + memupd->FspmConfig.Ch0_TristateClk1 = 0x0; + memupd->FspmConfig.Ch0_Mode2N = 0x0; + memupd->FspmConfig.Ch0_OdtLevels = 0x0; + memupd->FspmConfig.Ch1_RankEnable = 0x3; + memupd->FspmConfig.Ch1_DeviceWidth = 0x1; + memupd->FspmConfig.Ch1_DramDensity = 0x2; + memupd->FspmConfig.Ch1_Option = 0x3; + memupd->FspmConfig.Ch1_OdtConfig = 0x0; + memupd->FspmConfig.Ch1_TristateClk1 = 0x0; + memupd->FspmConfig.Ch1_Mode2N = 0x0; + memupd->FspmConfig.Ch1_OdtLevels = 0x0; + memupd->FspmConfig.Ch2_RankEnable = 0x3; + memupd->FspmConfig.Ch2_DeviceWidth = 0x1; + memupd->FspmConfig.Ch2_DramDensity = 0x2; + memupd->FspmConfig.Ch2_Option = 0x3; + memupd->FspmConfig.Ch2_OdtConfig = 0x0; + memupd->FspmConfig.Ch2_TristateClk1 = 0x0; + memupd->FspmConfig.Ch2_Mode2N = 0x0; + memupd->FspmConfig.Ch2_OdtLevels = 0x0; + memupd->FspmConfig.Ch3_RankEnable = 0x3; + memupd->FspmConfig.Ch3_DeviceWidth = 0x1; + memupd->FspmConfig.Ch3_DramDensity = 0x2; + memupd->FspmConfig.Ch3_Option = 0x3; + memupd->FspmConfig.Ch3_OdtConfig = 0x0; + memupd->FspmConfig.Ch3_TristateClk1 = 0x0; + memupd->FspmConfig.Ch3_Mode2N = 0x0; + memupd->FspmConfig.Ch3_OdtLevels = 0x0; + memupd->FspmConfig.RmtCheckRun = 0x0; + memupd->FspmConfig.MrcDataSaving = 0x0; + memupd->FspmConfig.MrcFastBoot = 0x0; + + memcpy(memupd->FspmConfig.Ch0_Bit_swizzling, &Ch0_Bit_swizzling, + sizeof(Ch0_Bit_swizzling)); + memcpy(memupd->FspmConfig.Ch1_Bit_swizzling, &Ch1_Bit_swizzling, + sizeof(Ch1_Bit_swizzling)); + memcpy(memupd->FspmConfig.Ch2_Bit_swizzling, &Ch2_Bit_swizzling, + sizeof(Ch2_Bit_swizzling)); + memcpy(memupd->FspmConfig.Ch3_Bit_swizzling, &Ch3_Bit_swizzling, + sizeof(Ch3_Bit_swizzling)); + + memupd->FspmConfig.RmtMarginCheckScaleHighThreshold = 0x0; + memupd->FspmConfig.MsgLevelMask = 0x0; +} |