diff options
Diffstat (limited to 'src/mainboard/tyan/s2895/Options.lb')
| -rw-r--r-- | src/mainboard/tyan/s2895/Options.lb | 43 |
1 files changed, 28 insertions, 15 deletions
diff --git a/src/mainboard/tyan/s2895/Options.lb b/src/mainboard/tyan/s2895/Options.lb index cd367ad029..b1ee5367e8 100644 --- a/src/mainboard/tyan/s2895/Options.lb +++ b/src/mainboard/tyan/s2895/Options.lb @@ -2,6 +2,8 @@ uses HAVE_MP_TABLE uses HAVE_PIRQ_TABLE uses USE_FALLBACK_IMAGE uses HAVE_FALLBACK_BOOT +uses USE_FAILOVER_IMAGE +uses HAVE_FAILOVER_BOOT uses HAVE_HARD_RESET uses IRQ_SLOT_COUNT uses HAVE_OPTION_TABLE @@ -11,6 +13,7 @@ uses CONFIG_LOGICAL_CPUS uses CONFIG_IOAPIC uses CONFIG_SMP uses FALLBACK_SIZE +uses FAILOVER_SIZE uses ROM_SIZE uses ROM_SECTION_SIZE uses ROM_IMAGE_SIZE @@ -60,6 +63,8 @@ uses DCACHE_RAM_BASE uses DCACHE_RAM_SIZE uses CONFIG_USE_INIT +uses SERIAL_CPU_INIT + uses ENABLE_APIC_EXT_ID uses APIC_ID_OFFSET uses LIFT_BSP_APIC_ID @@ -69,28 +74,34 @@ uses HT_CHAIN_END_UNITID_BASE uses SB_HT_CHAIN_ON_BUS0 uses SB_HT_CHAIN_UNITID_OFFSET_ONLY +uses CONFIG_LB_MEM_TOPK + ## ROM_SIZE is the size of boot ROM that this board will use. #512K bytes -#default ROM_SIZE=524288 +default ROM_SIZE=524288 #1M bytes -default ROM_SIZE=1048576 +#default ROM_SIZE=1048576 ## ## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use ## #default FALLBACK_SIZE=131072 -#256K -default FALLBACK_SIZE=0x40000 +#default FALLBACK_SIZE=0x40000 -### -### Build options -### +#FALLBACK: 256K-4K +default FALLBACK_SIZE=0x3f000 +#FAILOVER: 4K +default FAILOVER_SIZE=0x01000 + +#more 1M for pgtbl +default CONFIG_LB_MEM_TOPK=2048 ## ## Build code for the fallback boot ## default HAVE_FALLBACK_BOOT=1 +default HAVE_FAILOVER_BOOT=1 ## ## Build code to reset the motherboard from linuxBIOS @@ -130,15 +141,14 @@ default CONFIG_MAX_CPUS=4 default CONFIG_MAX_PHYSICAL_CPUS=2 default CONFIG_LOGICAL_CPUS=1 +default SERIAL_CPU_INIT=0 + #CHIP_NAME ? #default CONFIG_CHIP_NAME=1 #1G memory hole default HW_MEM_HOLE_SIZEK=0x100000 -#Opteron K8 1G HT Support -default K8_HT_FREQ_1G_SUPPORT=1 - ##HT Unit ID offset, default is 1, the typical one default HT_CHAIN_UNITID_BASE=0x0 @@ -151,6 +161,9 @@ default SB_HT_CHAIN_ON_BUS0=2 ##only offset for SB chain?, default is yes(1) default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0 +#Opteron K8 1G HT Support +default K8_HT_FREQ_1G_SUPPORT=1 + #VGA default CONFIG_CONSOLE_VGA=1 default CONFIG_PCI_ROM_RUN=1 @@ -163,7 +176,7 @@ default DCACHE_RAM_BASE=0xcf000 default DCACHE_RAM_SIZE=0x1000 default CONFIG_USE_INIT=0 -default ENABLE_APIC_EXT_ID=1 +default ENABLE_APIC_EXT_ID=0 default APIC_ID_OFFSET=0x10 default LIFT_BSP_APIC_ID=0 @@ -201,12 +214,12 @@ default HEAP_SIZE=0x4000 ## ## Only use the option table in a normal image ## -default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE +default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE ) ## ## LinuxBIOS C code runs at this location in RAM ## -default _RAMBASE=0x00004000 +default _RAMBASE=0x00100000 ## ## Load the payload from the ROM @@ -220,8 +233,8 @@ default CONFIG_ROM_STREAM = 1 ## ## The default compiler ## -default CC="$(CROSS_COMPILE)gcc -m32" -default HOSTCC="gcc" +default CC="$(CROSS_COMPILE)gcc-4.0.2 -m32" +default HOSTCC="gcc-4.0.2" ## ## Disable the gdb stub by default |