diff options
Diffstat (limited to 'src/mainboard/via')
| -rw-r--r-- | src/mainboard/via/epia/Config.lb | 137 |
1 files changed, 28 insertions, 109 deletions
diff --git a/src/mainboard/via/epia/Config.lb b/src/mainboard/via/epia/Config.lb index 30bd43b86c..ce6f762985 100644 --- a/src/mainboard/via/epia/Config.lb +++ b/src/mainboard/via/epia/Config.lb @@ -1,86 +1,3 @@ -uses HAVE_MP_TABLE -uses HAVE_PIRQ_TABLE -uses USE_FALLBACK_IMAGE -uses HAVE_FALLBACK_BOOT -uses HAVE_HARD_RESET -uses HAVE_OPTION_TABLE -uses USE_OPTION_TABLE -uses CONFIG_ROM_STREAM -uses IRQ_SLOT_COUNT -uses MAINBOARD -uses ARCH -uses FALLBACK_SIZE -uses STACK_SIZE -uses HEAP_SIZE -uses ROM_SIZE -uses ROM_SECTION_SIZE -uses ROM_IMAGE_SIZE -uses ROM_SECTION_SIZE -uses ROM_SECTION_OFFSET -uses CONFIG_ROM_STREAM_START -uses PAYLOAD_SIZE -uses _ROMBASE -uses XIP_ROM_SIZE -uses XIP_ROM_BASE -uses HAVE_MP_TABLE - -## ROM_SIZE is the size of boot ROM that this board will use. -default ROM_SIZE = 256*1024 - -### -### Build options -### - -## -## Build code for the fallback boot -## -default HAVE_FALLBACK_BOOT=1 - -## -## no MP table -## -default HAVE_MP_TABLE=0 - -## -## Build code to reset the motherboard from linuxBIOS -## -default HAVE_HARD_RESET=1 - -## -## Build code to export a programmable irq routing table -## -default HAVE_PIRQ_TABLE=1 -default IRQ_SLOT_COUNT=5 -object irq_tables.o - -## -## Build code to export a CMOS option table -## -default HAVE_OPTION_TABLE=1 - -### -### LinuxBIOS layout values -### - -## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. -default ROM_IMAGE_SIZE = 65536 - -## -## Use a small 8K stack -## -default STACK_SIZE=0x2000 - -## -## Use a small 16K heap -## -default HEAP_SIZE=0x4000 - -## -## Only use the option table in a normal image -## -#default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE -default USE_OPTION_TABLE = 0 - ## ## Compute the location and size of where this firmware image ## (linuxBIOS plus bootloader) will live in the boot rom chip. @@ -155,20 +72,20 @@ end ## ## Build our 16 bit and 32 bit linuxBIOS entry code ## -mainboardinit cpu/i386/entry16.inc -mainboardinit cpu/i386/entry32.inc -ldscript /cpu/i386/entry16.lds -ldscript /cpu/i386/entry32.lds +mainboardinit cpu/x86/16bit/entry16.inc +mainboardinit cpu/x86/32bit/entry32.inc +ldscript /cpu/x86/16bit/entry16.lds +ldscript /cpu/x86/32bit/entry32.lds ## ## Build our reset vector (This is where linuxBIOS is entered) ## if USE_FALLBACK_IMAGE - mainboardinit cpu/i386/reset16.inc - ldscript /cpu/i386/reset16.lds + mainboardinit cpu/x86/16bit/reset16.inc + ldscript /cpu/x86/16bit/reset16.lds else - mainboardinit cpu/i386/reset32.inc - ldscript /cpu/i386/reset32.lds + mainboardinit cpu/x86/32bit/reset32.inc + ldscript /cpu/x86/32bit/reset32.lds end ### Should this be in the northbridge code? @@ -210,10 +127,10 @@ mainboardinit ./auto.inc dir /pc80 config chip.h -northbridge via/vt8601 "vt8601" +chip northbridge/via/vt8601 # pci 0:0.0 # pci 0:1.0 - southbridge via/vt8231 "vt8231" + chip southbridge/via/vt8231 # pci 0:11.0 # pci 0:11.1 # pci 0:11.2 @@ -227,32 +144,38 @@ northbridge via/vt8601 "vt8601" register "enable_com_ports" = "1" register "enable_keyboard" = "0" register "enable_nvram" = "1" - superio winbond/w83627hf link 1 - pnp 2e.0 on # Floppy + chip superio/winbond/w83627hf + device pnp 2e.0 on # Floppy io 0x60 = 0x3f0 irq 0x70 = 6 drq 0x74 = 2 - pnp 2e.1 off # Parallel Port + end + device pnp 2e.1 off # Parallel Port io 0x60 = 0x378 irq 0x70 = 7 - pnp 2e.2 on # Com1 + end + device pnp 2e.2 on # Com1 io 0x60 = 0x3f8 irq 0x70 = 4 - pnp 2e.3 off # Com2 + end + device pnp 2e.3 off # Com2 io 0x60 = 0x2f8 irq 0x70 = 3 - pnp 2e.5 on # Keyboard + end + device pnp 2e.5 on # Keyboard io 0x60 = 0x60 io 0x62 = 0x64 irq 0x70 = 1 irq 0x72 = 12 - pnp 2e.6 off # CIR - pnp 2e.7 off # GAME_MIDI_GIPO1 - pnp 2e.8 off # GPIO2 - pnp 2e.9 off # GPIO3 - pnp 2e.a off # ACPI - pnp 2e.b on # HW Monitor + end + device pnp 2e.6 off end # CIR + device pnp 2e.7 off end # GAME_MIDI_GIPO1 + device pnp 2e.8 off end # GPIO2 + device pnp 2e.9 off end # GPIO3 + device pnp 2e.a off end # ACPI + device pnp 2e.b on # HW Monitor io 0x60 = 0x290 + end register "com1" = "{1}" # register "com1" = "{1, 0, 0x3f8, 4}" # register "lpt" = "{1}" @@ -260,10 +183,6 @@ northbridge via/vt8601 "vt8601" end end -cpu p6 "cpu0" - -end - ## ## Include the old serial code for those few places that still need it. ## |