diff options
Diffstat (limited to 'src/mainboard')
| -rw-r--r-- | src/mainboard/google/pit/mainboard.c | 124 |
1 files changed, 123 insertions, 1 deletions
diff --git a/src/mainboard/google/pit/mainboard.c b/src/mainboard/google/pit/mainboard.c index b91040cc3f..515424a490 100644 --- a/src/mainboard/google/pit/mainboard.c +++ b/src/mainboard/google/pit/mainboard.c @@ -51,6 +51,126 @@ static struct edid edid = { .bpp = 16, }; +static const struct parade_write parade_writes[] = { + { 0x02, 0xa1, 0x01 }, /* HPD low */ + /* + * SW setting + * [1:0] SW output 1.2V voltage is lower to 96% + */ + { 0x04, 0x14, 0x01 }, + /* + * RCO SS setting + * [5:4] = b01 0.5%, b10 1%, b11 1.5% + */ + { 0x04, 0xe3, 0x20 }, + { 0x04, 0xe2, 0x80 }, /* [7] RCO SS enable */ + /* + * RPHY Setting + * [3:2] CDR tune wait cycle before + * measure for fine tune b00: 1us, + * 01: 0.5us, 10:2us, 11:4us. + */ + { 0x04, 0x8a, 0x0c }, + { 0x04, 0x89, 0x08 }, /* [3] RFD always on */ + /* + * CTN lock in/out: + * 20000ppm/80000ppm. Lock out 2 + * times. + */ + { 0x04, 0x71, 0x2d }, + /* + * 2.7G CDR settings + * NOF=40LSB for HBR CDR setting + */ + { 0x04, 0x7d, 0x07 }, + { 0x04, 0x7b, 0x00 }, /* [1:0] Fmin=+4bands */ + { 0x04, 0x7a, 0xfd }, /* [7:5] DCO_FTRNG=+-40% */ + /* + * 1.62G CDR settings + * [5:2]NOF=64LSB [1:0]DCO scale is 2/5 + */ + { 0x04, 0xc0, 0x12 }, + { 0x04, 0xc1, 0x92 }, /* Gitune=-37% */ + { 0x04, 0xc2, 0x1c }, /* Fbstep=100% */ + { 0x04, 0x32, 0x80 }, /* [7] LOS signal disable */ + /* + * RPIO Setting + * [7:4] LVDS driver bias current : + * 75% (250mV swing) + */ + { 0x04, 0x00, 0xb0 }, + /* + * [7:6] Right-bar GPIO output strength is 8mA + */ + { 0x04, 0x15, 0x40 }, + /* EQ Training State Machine Setting */ + { 0x04, 0x54, 0x10 }, /* RCO calibration start */ + /* [4:0] MAX_LANE_COUNT set to one lane */ + { 0x01, 0x02, 0x81 }, + /* [4:0] LANE_COUNT_SET set to one lane */ + { 0x01, 0x21, 0x81 }, + { 0x00, 0x52, 0x20 }, + { 0x00, 0xf1, 0x03 }, /* HPD CP toggle enable */ + { 0x00, 0x62, 0x41 }, + /* Counter number, add 1ms counter delay */ + { 0x00, 0xf6, 0x01 }, + /* + * [6]PWM function control by + * DPCD0040f[7], default is PWM + * block always works. + */ + { 0x00, 0x77, 0x06 }, + /* + * 04h Adjust VTotal tolerance to + * fix the 30Hz no display issue + */ + { 0x00, 0x4c, 0x04 }, + /* DPCD00400='h00, Parade OUI = 'h001cf8 */ + { 0x01, 0xc0, 0x00 }, + { 0x01, 0xc1, 0x1c }, /* DPCD00401='h1c */ + { 0x01, 0xc2, 0xf8 }, /* DPCD00402='hf8 */ + /* + * DPCD403~408 = ASCII code + * D2SLV5='h4432534c5635 + */ + { 0x01, 0xc3, 0x44 }, + { 0x01, 0xc4, 0x32 }, /* DPCD404 */ + { 0x01, 0xc5, 0x53 }, /* DPCD405 */ + { 0x01, 0xc6, 0x4c }, /* DPCD406 */ + { 0x01, 0xc7, 0x56 }, /* DPCD407 */ + { 0x01, 0xc8, 0x35 }, /* DPCD408 */ + /* + * DPCD40A, Initial Code major revision + * '01' + */ + { 0x01, 0xca, 0x01 }, + /* DPCD40B, Initial Code minor revision '05' */ + { 0x01, 0xcb, 0x05 }, + /* DPCD720, Select internal PWM */ + { 0x01, 0xa5, 0xa0 }, + /* + * FFh for 100% PWM of brightness, 0h for 0% + * brightness + */ + { 0x01, 0xa7, 0xff }, + /* + * Set LVDS output as 6bit-VESA mapping, + * single LVDS channel + */ + { 0x01, 0xcc, 0x13 }, + /* Enable SSC set by register */ + { 0x02, 0xb1, 0x20 }, + /* + * Set SSC enabled and +/-1% central + * spreading + */ + { 0x04, 0x10, 0x16 }, + /* MPU Clock source: LC => RCO */ + { 0x04, 0x59, 0x60 }, + { 0x04, 0x54, 0x14 }, /* LC -> RCO */ + { 0x02, 0xa1, 0x91 } /* HPD high */ +}; + /* TODO: transplanted DP stuff, clean up once we have something that works */ static enum exynos5_gpio_pin dp_pd_l = GPIO_X35; /* active low */ static enum exynos5_gpio_pin dp_rst_l = GPIO_Y77; /* active low */ @@ -83,7 +203,9 @@ static void parade_dp_bridge_setup(void) exynos_pinmux_i2c7(); i2c_init(7, 100000, 0x00); - parade_ps8625_bridge_setup(7, 0x48); + parade_ps8625_bridge_setup(7, 0x48, + parade_writes, + ARRAY_SIZE(parade_writes)); } /* |