summaryrefslogtreecommitdiff
path: root/src/mainboard
diff options
context:
space:
mode:
Diffstat (limited to 'src/mainboard')
-rw-r--r--src/mainboard/arima/hdama/Config.lb385
-rw-r--r--src/mainboard/arima/hdama/Options.lb124
2 files changed, 189 insertions, 320 deletions
diff --git a/src/mainboard/arima/hdama/Config.lb b/src/mainboard/arima/hdama/Config.lb
index f8091bdbe8..c5ed005f80 100644
--- a/src/mainboard/arima/hdama/Config.lb
+++ b/src/mainboard/arima/hdama/Config.lb
@@ -1,127 +1,3 @@
-uses HAVE_MP_TABLE
-uses HAVE_PIRQ_TABLE
-uses USE_FALLBACK_IMAGE
-uses HAVE_FALLBACK_BOOT
-uses HAVE_HARD_RESET
-uses HARD_RESET_BUS
-uses HARD_RESET_DEVICE
-uses HARD_RESET_FUNCTION
-uses IRQ_SLOT_COUNT
-uses HAVE_OPTION_TABLE
-uses CONFIG_MAX_CPUS
-uses CONFIG_IOAPIC
-uses CONFIG_SMP
-uses FALLBACK_SIZE
-uses ROM_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_IMAGE_SIZE
-uses ROM_SECTION_SIZE
-uses ROM_SECTION_OFFSET
-uses CONFIG_ROM_STREAM
-uses CONFIG_ROM_STREAM_START
-uses PAYLOAD_SIZE
-uses _ROMBASE
-uses XIP_ROM_SIZE
-uses XIP_ROM_BASE
-uses STACK_SIZE
-uses HEAP_SIZE
-uses USE_OPTION_TABLE
-uses LB_CKS_RANGE_START
-uses LB_CKS_RANGE_END
-uses LB_CKS_LOC
-uses MAINBOARD_PART_NUMBER
-uses MAINBOARD_VENDOR
-uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
-uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
-
-
-## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE=524288
-
-###
-### Build options
-###
-
-##
-## Build code for the fallback boot
-##
-default HAVE_FALLBACK_BOOT=1
-
-##
-## Build code to reset the motherboard from linuxBIOS
-##
-default HAVE_HARD_RESET=1
-
-default HARD_RESET_BUS=1
-default HARD_RESET_DEVICE=4
-default HARD_RESET_FUNCTION=0
-
-##
-## Build code to export a programmable irq routing table
-##
-default HAVE_PIRQ_TABLE=1
-default IRQ_SLOT_COUNT=9
-
-##
-## Build code to export an x86 MP table
-## Useful for specifying IRQ routing values
-##
-default HAVE_MP_TABLE=1
-
-##
-## Build code to export a CMOS option table
-##
-default HAVE_OPTION_TABLE=1
-
-##
-## Move the default LinuxBIOS cmos range off of AMD RTC registers
-##
-default LB_CKS_RANGE_START=49
-default LB_CKS_RANGE_END=122
-default LB_CKS_LOC=123
-
-##
-## Build code for SMP support
-## Only worry about 2 micro processors
-##
-default CONFIG_SMP=1
-default CONFIG_MAX_CPUS=2
-
-##
-## Build code to setup a generic IOAPIC
-##
-default CONFIG_IOAPIC=1
-
-##
-## Clean up the motherboard id strings
-##
-default MAINBOARD_PART_NUMBER="HDAMA"
-default MAINBOARD_VENDOR="ARIMA"
-default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f
-default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016
-
-###
-### LinuxBIOS layout values
-###
-
-## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
-default ROM_IMAGE_SIZE = 65536
-
-##
-## Use a small 8K stack
-##
-default STACK_SIZE=0x2000
-
-##
-## Use a small 32K heap
-##
-default HEAP_SIZE=0x8000
-
-##
-## Only use the option table in a normal image
-##
-default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
-
##
## Compute the location and size of where this firmware image
## (linuxBIOS plus bootloader) will live in the boot rom chip.
@@ -157,203 +33,72 @@ default _ROMBASE = ( CONFIG_ROM_STREAM_START + PAYLOAD_SIZE )
default XIP_ROM_SIZE=65536
default XIP_ROM_BASE = ( _ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE )
-##
-## Set all of the defaults for an x86 architecture
-##
-
-arch i386 end
-
-##
-## Build the objects we have code for in this directory.
-##
-
-driver mainboard.o
-if HAVE_MP_TABLE object mptable.o end
-if HAVE_PIRQ_TABLE object irq_tables.o end
-
-##
-## Romcc output
-##
-makerule ./failover.E
- depends "$(MAINBOARD)/failover.c"
- action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E"
-end
-
-makerule ./failover.inc
- depends "./failover.E ./romcc"
- action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"
-end
-
-makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h "
- action "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
-end
-makerule ./auto.inc
- depends "./auto.E ./romcc"
- action "./romcc -mcpu=k8 -O2 ./auto.E > auto.inc"
-end
-
-##
-## Build our 16 bit and 32 bit linuxBIOS entry code
-##
-mainboardinit cpu/x86/16bit/entry16.inc
-mainboardinit cpu/x86/32bit/entry32.inc
-ldscript /cpu/x86/16bit/entry16.lds
-ldscript /cpu/x86/32bit/entry32.lds
-
-##
-## Build our reset vector (This is where linuxBIOS is entered)
-##
-if USE_FALLBACK_IMAGE
- mainboardinit cpu/x86/16bit/reset16.inc
- ldscript /cpu/x86/16bit/reset16.lds
-else
- mainboardinit cpu/x86/32bit/reset32.inc
- ldscript /cpu/x86/32bit/reset32.lds
-end
-
-### Should this be in the northbridge code?
-mainboardinit arch/i386/lib/cpu_reset.inc
-
-##
-## Include an id string (For safe flashing)
-##
-mainboardinit arch/i386/lib/id.inc
-ldscript /arch/i386/lib/id.lds
-
-###
-### This is the early phase of linuxBIOS startup
-### Things are delicate and we test to see if we should
-### failover to another image.
-###
-if USE_FALLBACK_IMAGE
- ldscript /arch/i386/lib/failover.lds
- mainboardinit ./failover.inc
-end
-
-###
-### O.k. We aren't just an intermediary anymore!
-###
-
-##
-## Setup RAM
-##
-mainboardinit cpu/x86/fpu/enable_fpu.inc
-mainboardinit cpu/x86/mmx/enable_mmx.inc
-mainboardinit cpu/x86/sse/enable_sse.inc
-mainboardinit ./auto.inc
-mainboardinit cpu/x86/sse/disable_sse.inc
-mainboardinit cpu/x86/mmx/disable_mmx.inc
-
-##
-## Include the secondary Configuration files
-##
-dir /pc80
-config chip.h
-
-northbridge amd/amdk8 "mc0"
- pnp cf8.0
- northbridge amd/amdk8 "mc1" link 0
- pci 0:19.0
- pci 0:19.0
- pci 0:19.0
- pci 0:19.1
- pci 0:19.2
- pci 0:19.3
- end
- pci 1:18.0
- southbridge amd/amd8131 "amd8131" link 1
- pci 0:0.0
- pci 0:0.1
- pci 0:1.0
- pci 0:1.1
- end
- southbridge amd/amd8111 "amd8111" link 1
- pci 0:0.0
- pci 0:1.0 on
- superio NSC/pc87360 link 1
- pnp 2e.0 off # Floppy
- io 0x60 = 0x3f0
- irq 0x70 = 6
- drq 0x74 = 2
- pnp 2e.1 off # Parallel Port
- io 0x60 = 0x378
- irq 0x70 = 7
- pnp 2e.2 off # Com 2
- io 0x60 = 0x2f8
- irq 0x70 = 3
- pnp 2e.3 on # Com 1
- io 0x60 = 0x3f8
- irq 0x70 = 4
- pnp 2e.4 off # SWC
- pnp 2e.5 off # Mouse
- pnp 2e.6 on # Keyboard
- io 0x60 = 0x60
- io 0x62 = 0x64
- irq 0x70 = 1
- pnp 2e.7 off # GPIO
- pnp 2e.8 off # ACB
- pnp 2e.9 off # FSCM
- pnp 2e.a off # WDT
- end
- pci 0:1.1 on
- pci 0:1.2 on
- pci 0:1.3 on # ACPI/SMBUS
- chip drivers/generic/generic link 4
- #phillips pca9545 smbus mux
- i2c 70
- # analog_devices adm1026
- chip drivers/generic/generic link 0
- i2c 2c
- end
- i2c 70
- i2c 70
- i2c 70
- end
- chip drivers/generic/generic link 4 #dimm 0-0-0
- i2c 50
+# sample config for arima/hdama
+chip northbridge/amd/amdk8
+ print "HI MOM!\n"
+ device pnp cf8.0 on # cf8 config
+ print "HI MOM!\n"
+ device pci 18.0 on # northbridge
+ print "HI MOM!\n"
+ # devices on link 0, link 0 == LDT 0
+ chip southbridge/amd/amd8131
+ print "SOUTH\n"
+ # the on/off keyword is mandatory
+ device pci 0.0 on end
+ print "SOUTH2\n"
+ device pci 0.1 on end
+ print "SOUTH3\n"
+ device pci 1.0 on end
+ print "SOUTH4\n"
+ device pci 1.1 on end
end
- chip drivers/generic/generic link 4 #dimm 0-0-1
- i2c 51
- end
- chip drivers/generic/generic link 4 #dimm 0-1-0
- i2c 52
- end
- chip drivers/generic/generic link 4 #dimm 0-1-1
- i2c 53
- end
- chip drivers/generic/generic link 4 #dimm 1-0-0
- i2c 54
+ chip southbridge/amd/amd8111
+ print "NEXT SOUTH\n"
+ # this "device pci 0.0" is the parent the next one
+ # PCI bridge
+ device pci 0.0 on
+ # this "device pci 0.0" is a child of the
+ # previous one
+ # devices behind the bridge
+ device pci 0.0 on end
+ device pci 0.1 on end
+ device pci 0.2 on end
+ # the device statement can span across multiple
+ # lines too
+ device pci 1.0
+ off
+ end
+ end
+ device pci 1.0 on
+ chip superio/NSC/pc87360
+ device pnp 2e.3 on
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ end
+ end
+ end
+ device pci 1.1 on end
+ device pci 1.2 off end
+ device pci 1.3 off end
+ device pci 1.5 on end
+ device pci 1.6 on end
end
- chip drivers/generic/generic link 4 #dimm 1-0-1
- i2c 55
- end
- chip drivers/generic/generic link 4 #dimm 1-1-0
- i2c 56
- end
- chip drivers/generic/generic link 4 #dimm 1-1-1
- i2c 57
- end
- pci 0:1.5 off
- pci 0:1.6 off
- pci 1:0.0 on
- pci 1:0.1 on
- pci 1:0.2 on
- pci 1:1.0 off
- end
- pci 1:18.0
- pci 1:18.0
- pci 1:18.1
- pci 1:18.2
- pci 1:18.3
-end
-
-
-cpu amd/socket_940 "cpu0" link 1
- apic 0
-end
-
-cpu amd/socket_940 "cpu1" link 1
- apic 1
+ end # device pci 18.0
+ device pci 18.0 on
+ # some non-existence devices on link 1
+ end
+ device pci 18.0 on
+ # some non-existence devices on link 2
+ end
+ device pci 18.1
+ # empty
+ end
+ device pci 18.2
+ # empty
+ end
+ device pci 18.3
+ # empty
+ end
+ end # device pnp
end
diff --git a/src/mainboard/arima/hdama/Options.lb b/src/mainboard/arima/hdama/Options.lb
new file mode 100644
index 0000000000..f2c2dba2bb
--- /dev/null
+++ b/src/mainboard/arima/hdama/Options.lb
@@ -0,0 +1,124 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_HARD_RESET
+uses HARD_RESET_BUS
+uses HARD_RESET_DEVICE
+uses HARD_RESET_FUNCTION
+uses IRQ_SLOT_COUNT
+uses HAVE_OPTION_TABLE
+uses CONFIG_MAX_CPUS
+uses CONFIG_IOAPIC
+uses CONFIG_SMP
+uses FALLBACK_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_STREAM
+uses CONFIG_ROM_STREAM_START
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses USE_OPTION_TABLE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD_PART_NUMBER
+uses MAINBOARD_VENDOR
+uses MAINBOARD
+uses LINUXBIOS_EXTRA_VERSION
+uses _RAMBASE
+
+
+## ROM_SIZE is the size of boot ROM that this board will use.
+default ROM_SIZE=524288
+
+###
+### Build options
+###
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+
+##
+## Build code to reset the motherboard from linuxBIOS
+##
+default HAVE_HARD_RESET=1
+
+default HARD_RESET_BUS=1
+default HARD_RESET_DEVICE=4
+default HARD_RESET_FUNCTION=0
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=9
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+default HAVE_MP_TABLE=1
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=1
+
+##
+## Move the default LinuxBIOS cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+##
+default CONFIG_SMP=1
+default CONFIG_MAX_CPUS=2
+
+##
+## Build code to setup a generic IOAPIC
+##
+default CONFIG_IOAPIC=1
+
+##
+## Clean up the motherboard id strings
+##
+default MAINBOARD_PART_NUMBER="HDAMA"
+default MAINBOARD_VENDOR="ARIMA"
+
+###
+### LinuxBIOS layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy.
+default ROM_IMAGE_SIZE = 65536
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 16K heap
+##
+default HEAP_SIZE=0x4000
+
+##
+## Only use the option table in a normal image
+##
+default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE
+default _RAMBASE=0x00004000
+end
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-03 18:44:34 +0000