diff options
Diffstat (limited to 'src/northbridge/intel/i440lx/raminit.c')
-rw-r--r-- | src/northbridge/intel/i440lx/raminit.c | 453 |
1 files changed, 0 insertions, 453 deletions
diff --git a/src/northbridge/intel/i440lx/raminit.c b/src/northbridge/intel/i440lx/raminit.c deleted file mode 100644 index fc19d9163d..0000000000 --- a/src/northbridge/intel/i440lx/raminit.c +++ /dev/null @@ -1,453 +0,0 @@ -/* - * This file is part of the coreboot project. - * - * Copyright (C) 2007-2008 Uwe Hermann <uwe@hermann-uwe.de> - * Copyright (C) 2009 Maciej Pijanka <maciej.pijanka@gmail.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc. - */ - -#include <spd.h> -#include <delay.h> -#include <stdlib.h> -#include "i440lx.h" - -/*----------------------------------------------------------------------------- -Macros and definitions. ------------------------------------------------------------------------------*/ - -/* Uncomment this to enable debugging output. */ - -/* Debugging macros. */ -#if CONFIG_DEBUG_RAM_SETUP -#define PRINT_DEBUG(x) printk(BIOS_DEBUG, x) -#define PRINT_DEBUG_HEX8(x) printk(BIOS_DEBUG, "%02x", x) -#define PRINT_DEBUG_HEX16(x) printk(BIOS_DEBUG, "%04x", x) -#define PRINT_DEBUG_HEX32(x) printk(BIOS_DEBUG, "%08x", x) -#define DUMPNORTH() dump_pci_device(PCI_DEV(0, 0, 0)) -#else -#define PRINT_DEBUG(x) -#define PRINT_DEBUG_HEX8(x) -#define PRINT_DEBUG_HEX16(x) -#define PRINT_DEBUG_HEX32(x) -#define DUMPNORTH() -#endif - -#define NB PCI_DEV(0, 0, 0) - -/* DRAMXC[7:5] - DRAM extended control register (SMS). */ -#define RAM_COMMAND_NORMAL 0x0 -#define RAM_COMMAND_NOP 0x1 // (NOPCE) -#define RAM_COMMAND_PRECHARGE 0x2 // ABPCE -#define RAM_COMMAND_MRS 0x3 // MRSCE -#define RAM_COMMAND_CBR 0x4 // CBRC -// rest are reserved - -/* Table format: register, bitmask, value. */ -static const long register_values[] = { - // ~0x02 == bit 9 - // 0x04 == bit 10 - // BASE is 0x8A but we dont want bit 9 or 10 have ENABLED so 0x8C - PACCFG + 1, 0x38, 0x8c, - - DBC, 0x00, 0xC3, - - DRT, 0x00, 0xFF, - DRT+1, 0x00, 0xFF, - - DRAMC, 0x00, 0x00, /* disable refresh for now. */ - DRAMT, 0x00, 0x00, - - PAM0, 0x00, 0x30, // everything is a mem - PAM1, 0x00, 0x33, - PAM2, 0x00, 0x33, - PAM3, 0x00, 0x33, - PAM4, 0x00, 0x33, - PAM5, 0x00, 0x33, - PAM6, 0x00, 0x33, - - /* Set the DRBs to zero for now, this will be fixed later. */ - DRB0, 0x00, 0x00, - DRB1, 0x00, 0x00, - DRB2, 0x00, 0x00, - DRB3, 0x00, 0x00, - DRB4, 0x00, 0x00, - DRB5, 0x00, 0x00, - DRB6, 0x00, 0x00, - DRB7, 0x00, 0x00, - - /* No memory holes. */ - FDHC, 0x00, 0x00, -}; - -/*----------------------------------------------------------------------------- -SDRAM configuration functions. ------------------------------------------------------------------------------*/ - -/** - * Send the specified RAM command to all DIMMs. - * - * @param command The RAM command to send to the DIMM(s). - */ -static void do_ram_command(u32 command) -{ - int i, caslatency; - u8 dimm_start, dimm_end; - u16 reg16; - u32 addr, addr_offset; - - /* Configure the RAM command. */ - reg16 = pci_read_config16(NB, DRAMXC); - reg16 &= 0xff1f; /* Clear bits 7-5. */ - reg16 |= (u16) (command << 5); /* Write command into bits 7-5. */ - pci_write_config16(NB, DRAMXC, reg16); - - /* - * RAM_COMMAND_NORMAL affects only the memory controller and - * doesn't need to be "sent" to the DIMMs. - */ - if (command == RAM_COMMAND_NORMAL) - return; - - /* Send the RAM command to each row of memory. */ - dimm_start = 0; - for (i = 0; i < (DIMM_SOCKETS * 2); i++) { - addr_offset = 0; - caslatency = 3; /* TODO: Dynamically get CAS latency later. */ - - /* before translation it is - * - * M[02:00] Burst Length - * M[03:03] Burst Type - * M[06:04] Cas Latency - * 000 - Reserved - * 001 - Reserved - * 010 - CAS 2 - * 011 - CAS 3 - * 100 - Reserved - * 101 - Reserved - * 110 - Reserved - * 111 - Reserved - * M[08:07] Op Mode - * Must Be 00b (Defined mode) - * M[09:09] Write Burst Mode - * 0 - Programmed burst length - * 1 - Single location access - * M[11:10] Reserved - * write 0 to ensure compatibility with.... - */ - - /* seems constructed value will be right shifted by 3 bit, thus constructed value - * must be left shifted by 3 - * so possible formula is (caslatency <<4)|(burst_type << 1)|(burst length) - * then << 3 shift to compensate shift in Memory Controller - */ - if (command == RAM_COMMAND_MRS) { - if (caslatency == 3) - addr_offset = 0x1d0; - if (caslatency == 2) - addr_offset = 0x150; - } - - dimm_end = pci_read_config8(NB, DRB + i); - - addr = (dimm_start * 8 * 1024 * 1024) + addr_offset; - if (dimm_end > dimm_start) { -#if 0 - PRINT_DEBUG(" Sending RAM command 0x"); - PRINT_DEBUG_HEX16(reg16); - PRINT_DEBUG(" to 0x"); - PRINT_DEBUG_HEX32(addr); - PRINT_DEBUG("\n"); -#endif - - read32(addr); - } - - /* Set the start of the next DIMM. */ - dimm_start = dimm_end; - } -} - -/*----------------------------------------------------------------------------- -DIMM-independant configuration functions. ------------------------------------------------------------------------------*/ - -static void spd_enable_refresh(void) -{ - uint8_t reg; - - reg = pci_read_config8(NB, DRAMC); - - /* this chipset offer only two choices regarding refresh - * refresh disabled, or refresh normal - */ - - pci_write_config8(NB, DRAMC, reg | 0x01); - reg = pci_read_config8(NB, DRAMC); - - PRINT_DEBUG("spd_enable_refresh: dramc = 0x"); - PRINT_DEBUG_HEX8(reg); - PRINT_DEBUG("\n"); -} - -/*----------------------------------------------------------------------------- -Public interface. ------------------------------------------------------------------------------*/ - -static void northbridge_init(void) -{ - uint32_t reg32; - - reg32 = pci_read_config32(NB, APBASE); - reg32 &= 0xe8000000U; - pci_write_config32(NB, APBASE, reg32); - -#if CONFIG_DEBUG_RAM_SETUP - /* - * apbase dont get set still, no idea what i have doing wrong yet, - * i am almost sure that somehow i set it by mistake once, but can't - * repeat that. - */ - reg32 = pci_read_config32(NB, APBASE); - PRINT_DEBUG("APBASE "); - PRINT_DEBUG_HEX32(reg32); - PRINT_DEBUG("\n"); -#endif -} - - -/** - * This routine sets RAM controller inside northbridge to known state - * - */ -static void sdram_set_registers(void) -{ - int i, max; - - /* nice banner with FSB shown? do we have - * any standart policy about such things? - */ -#if 0 - uint16_t reg16; - reg16 = pci_read_config16(NB, PACCFG); - printk(BIOS_DEBUG, "i82443LX Host Freq: 6%C MHz\n", (reg16 & 0x4000) ? '0' : '6'); -#endif - - PRINT_DEBUG("Northbridge prior to SDRAM init:\n"); - DUMPNORTH(); - - northbridge_init(); - - max = ARRAY_SIZE(register_values); - - /* Set registers as specified in the register_values[] array. */ - for (i = 0; i < max; i += 3) { - uint8_t reg,tmp; - reg = pci_read_config8(NB, register_values[i]); - reg &= register_values[i + 1]; - reg |= register_values[i + 2] & ~(register_values[i + 1]); - pci_write_config8(NB, register_values[i], reg); - - /* - * i am not sure if that is needed, but was usefull - * for me to confirm what got written - */ -#if CONFIG_DEBUG_RAM_SETUP - PRINT_DEBUG(" Set register 0x"); - PRINT_DEBUG_HEX8(register_values[i]); - PRINT_DEBUG(" to 0x"); - PRINT_DEBUG_HEX8(reg); - tmp = pci_read_config8(NB, register_values[i]); - PRINT_DEBUG(" readed 0x"); - PRINT_DEBUG_HEX8(tmp); - if (tmp == reg) { - PRINT_DEBUG(" OK "); - } else { - PRINT_DEBUG(" FAIL "); - } - PRINT_DEBUG("\n"); -#endif - } - - PRINT_DEBUG("Northbridge atexit sdram set registers\n"); - DUMPNORTH(); -} - - -static void sdram_set_spd_registers(void) -{ - int i; - u16 memsize = 0; - - for (i = 0; i < DIMM_SOCKETS; i++) { - uint16_t ds = 0; // dimm size - int j; - /* this code skips second bank on each socket (no idea how to fix it now) - */ - - PRINT_DEBUG("DIMM"); - PRINT_DEBUG_HEX8(i); - PRINT_DEBUG(" rows: "); - PRINT_DEBUG_HEX8(spd_read_byte(DIMM0 + i, SPD_NUM_DIMM_BANKS) & 0xFF); - PRINT_DEBUG(" rowsize: "); - PRINT_DEBUG_HEX8(spd_read_byte(DIMM0 + i, SPD_DENSITY_OF_EACH_ROW_ON_MODULE) & 0xFF); - PRINT_DEBUG(" modulesize: "); - - j = spd_read_byte(DIMM0 + i, SPD_NUM_DIMM_BANKS); - if (j < 0) - j = 0; - else - ds = j; - - j = spd_read_byte(DIMM0 + i, SPD_DENSITY_OF_EACH_ROW_ON_MODULE); - - if (j < 0) - j = 0; - else - ds = ds * (j >> 1); // convert from 4MB to 8MB units in place - - - /* This is more or less crude hack - * allowing to run this target under qemu (even if that is not really - * same hardware emulated), - * probably some kconfig expert option should be added to enable/disable - * this nicelly - */ -#if 0 - if (ds == 0 && memsize == 0) - ds = 0x8; -#endif - - - // todo: support for bank with not equal sizes as per jedec standart? - - /* - * because density is reported in units of 4Mbyte - * and rows in device are just value, - * and for setting registers we need value in 8Mbyte units - */ - - PRINT_DEBUG_HEX16(ds); - PRINT_DEBUG("\n"); - - memsize += ds; - - pci_write_config8(NB, DRB + (2*i), memsize); - pci_write_config8(NB, DRB + (2*i) + 1, memsize); - if (ds > 0) { - /* i have no idea why pci_read_config16 not work for - * me correctly here - */ - ds = pci_read_config8(NB, DRT+1); - ds <<=8; - ds |= pci_read_config8(NB, DRT); - - PRINT_DEBUG("DRT "); - PRINT_DEBUG_HEX16(ds); - - ds &= ~(0x01 << (4 * i)); - - PRINT_DEBUG(" "); - PRINT_DEBUG_HEX16(ds); - PRINT_DEBUG("\n"); - - /* - * modify DRT register if current row isn't empty - * code assume its SDRAM plugged (should check if its sdram or EDO, - * edo would have 0x00 as constand instead 0x10 for SDRAM - * also this code is buggy because ignores second row of each dimm socket - */ - - /* and as above write_config16 not work here too) - * pci_write_config16(NB, DRT, j); - */ - - pci_write_config8(NB, DRT+1, ds >> 8); - pci_write_config8(NB, DRT, ds & 0xFF); - } - } - -#if 0 - PRINT_DEBUG("Mem: 0x"); - PRINT_DEBUG_HEX16(memsize * 8); - PRINT_DEBUG(" MB\n"); - - if (memsize == 0) { - /* maybe we should use some nice die/hlt sequence with printing on console - * that no memory found, get lost, i can't run? - * maybe such event_handler can be commonly defined routine to decrease - * code duplication? - */ - PRINT_DEBUG("No memory detected via SPD\n"); - PRINT_DEBUG("Reverting to hardcoded 64M single side dimm in first bank\n"); - } -#endif - - /* Set DRAMC. Don't enable refresh for now. */ - pci_write_config8(NB, DRAMC, 0x00); - - /* Cas latency 3, and other shouldbe properly from spd too */ - pci_write_config8(NB, DRAMT, 0xAC); - - /* TODO? */ - pci_write_config8(NB, PCI_LATENCY_TIMER, 0x40); - - // set drive strength - pci_write_config32(NB, MBSC, 0x00000000); -} - -static void sdram_enable(void) -{ - int i; - - /* 0. Wait until power/voltages and clocks are stable (200us). */ - udelay(200); - - /* 1. Apply NOP. Wait 200 clock cycles (clock might be 60 or 66 MHz). */ - PRINT_DEBUG("RAM Enable 1: Apply NOP\n"); - do_ram_command(RAM_COMMAND_NOP); - udelay(200); - - /* 2. Precharge all. Wait tRP. */ - PRINT_DEBUG("RAM Enable 2: Precharge all\n"); - do_ram_command(RAM_COMMAND_PRECHARGE); - udelay(1); - - /* 3. Perform 8 refresh cycles. Wait tRC each time. */ - PRINT_DEBUG("RAM Enable 3: CBR\n"); - for (i = 0; i < 8; i++) { - do_ram_command(RAM_COMMAND_CBR); - udelay(1); - } - - /* 4. Mode register set. Wait two memory cycles. */ - PRINT_DEBUG("RAM Enable 4: Mode register set\n"); - do_ram_command(RAM_COMMAND_MRS); - udelay(2); - - /* 5. Normal operation. */ - PRINT_DEBUG("RAM Enable 5: Normal operation\n"); - do_ram_command(RAM_COMMAND_NORMAL); - udelay(1); - - /* 6. Finally enable refresh. */ - PRINT_DEBUG("RAM Enable 6: Enable refresh\n"); - pci_write_config8(NB, DRAMC, 0x01); - spd_enable_refresh(); - udelay(1); - - PRINT_DEBUG("Northbridge following SDRAM init:\n"); -} |