diff options
Diffstat (limited to 'src/southbridge/intel/i82801dx/early_smbus.c')
-rw-r--r-- | src/southbridge/intel/i82801dx/early_smbus.c | 196 |
1 files changed, 196 insertions, 0 deletions
diff --git a/src/southbridge/intel/i82801dx/early_smbus.c b/src/southbridge/intel/i82801dx/early_smbus.c new file mode 100644 index 0000000000..f58cd86342 --- /dev/null +++ b/src/southbridge/intel/i82801dx/early_smbus.c @@ -0,0 +1,196 @@ +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2004 Ronald G. Minnich + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; version 2 of + * the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include "i82801dx.h" + +#define SMBHSTSTAT 0x0 +#define SMBHSTCTL 0x2 +#define SMBHSTCMD 0x3 +#define SMBXMITADD 0x4 +#define SMBHSTDAT0 0x5 +#define SMBHSTDAT1 0x6 +#define SMBBLKDAT 0x7 +#define SMBTRNSADD 0x9 +#define SMBSLVDATA 0xa +#define SMLINK_PIN_CTL 0xe +#define SMBUS_PIN_CTL 0xf + +/* Between 1-10 seconds, We should never timeout normally + * Longer than this is just painful when a timeout condition occurs. + */ +//#define SMBUS_TIMEOUT (100*1000*10) + +static void enable_smbus(void) +{ + device_t dev = PCI_DEV(0x0, 0x1f, 0x3); + + printk(BIOS_DEBUG, "SMBus controller enabled\n"); + /* set smbus iobase */ + pci_write_config32(dev, 0x20, SMBUS_IO_BASE | 1); + /* Set smbus enable */ + pci_write_config8(dev, 0x40, 0x01); + /* Set smbus iospace enable */ + pci_write_config16(dev, 0x4, 0x01); + /* Disable interrupt generation */ + outb(0, SMBUS_IO_BASE + SMBHSTCTL); + /* clear any lingering errors, so the transaction will run */ + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT); +} + +static inline void smbus_delay(void) +{ + outb(0x80, 0x80); +} + +static int smbus_wait_until_active(void) +{ + unsigned long loops; + loops = SMBUS_TIMEOUT; + do { + unsigned char val; + smbus_delay(); + val = inb(SMBUS_IO_BASE + SMBHSTSTAT); + if ((val & 1)) { + break; + } + } while (--loops); + return loops ? 0 : -4; +} + +static int smbus_wait_until_ready(void) +{ + unsigned long loops; + loops = SMBUS_TIMEOUT; + do { + unsigned char val; + smbus_delay(); + val = inb(SMBUS_IO_BASE + SMBHSTSTAT); + if ((val & 1) == 0) { + break; + } + if (loops == (SMBUS_TIMEOUT / 2)) { + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), + SMBUS_IO_BASE + SMBHSTSTAT); + } + } while (--loops); + return loops ? 0 : -2; +} + +static int smbus_wait_until_done(void) +{ + unsigned long loops; + loops = SMBUS_TIMEOUT; + do { + unsigned char val; + smbus_delay(); + + val = inb(SMBUS_IO_BASE + SMBHSTSTAT); + if ((val & 1) == 0) { + break; + } + if ((val & ~((1 << 6) | (1 << 0))) != 0) { + break; + } + } while (--loops); + return loops ? 0 : -3; +} + +static int smbus_read_byte(unsigned device, unsigned address) +{ + unsigned char global_status_register; + unsigned char byte; + + /* printk(BIOS_ERR, "smbus_read_byte\n"); */ + if (smbus_wait_until_ready() < 0) { + printk(BIOS_ERR, "SMBUS not ready (%02x)\n", -2); + return -2; + } + + /* setup transaction */ + /* disable interrupts */ + outb(inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xfe, SMBUS_IO_BASE + SMBHSTCTL); + /* set the device I'm talking too */ + outb(((device & 0x7f) << 1) | 1, SMBUS_IO_BASE + SMBXMITADD); + /* set the command/address... */ + outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD); + /* set up for a byte data read */ + outb((inb(SMBUS_IO_BASE + SMBHSTCTL) & 0xe3) | (0x2 << 2), + SMBUS_IO_BASE + SMBHSTCTL); + + /* clear any lingering errors, so the transaction will run */ + outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT); + + /* clear the data byte... */ + outb(0, SMBUS_IO_BASE + SMBHSTDAT0); + + /* start a byte read, with interrupts disabled */ + outb((inb(SMBUS_IO_BASE + SMBHSTCTL) | 0x40), + SMBUS_IO_BASE + SMBHSTCTL); + /* poll for it to start */ + if (smbus_wait_until_active() < 0) { + printk(BIOS_ERR, "SMBUS not active (%02x)\n", -4); + return -4; + } + + /* poll for transaction completion */ + if (smbus_wait_until_done() < 0) { + printk(BIOS_ERR, "SMBUS not completed (%02x)\n", -3); + return -3; + } + + global_status_register = inb(SMBUS_IO_BASE + SMBHSTSTAT) & ~(1 << 6); /* Ignore the In Use Status... */ + + /* read results of transaction */ + byte = inb(SMBUS_IO_BASE + SMBHSTDAT0); + + if (global_status_register != 2) { + //printk(BIOS_SPEW, "%s: no device (%02x, %02x)\n", __func__, device, address); + return -1; + } + //printk(BIOS_DEBUG, "%s: %02x@%02x = %02x\n", __func__, device, address, byte); + return byte; +} + +#if 0 +static void smbus_write_byte(unsigned device, unsigned address, + unsigned char val) +{ + if (smbus_wait_until_ready() < 0) { + return; + } + + /* by LYH */ + outb(0x37, SMBUS_IO_BASE + SMBHSTSTAT); + /* set the device I'm talking too */ + outw(((device & 0x7f) << 1) | 0, SMBUS_IO_BASE + SMBHSTADDR); + + /* data to send */ + outb(val, SMBUS_IO_BASE + SMBHSTDAT); + + outb(address & 0xFF, SMBUS_IO_BASE + SMBHSTCMD); + + /* start the command */ + outb(0xa, SMBUS_IO_BASE + SMBHSTCTL); + + /* poll for transaction completion */ + smbus_wait_until_done(); + return; +} +#endif |