summaryrefslogtreecommitdiff
path: root/src
diff options
context:
space:
mode:
Diffstat (limited to 'src')
-rw-r--r--src/southbridge/amd/cs5536_lx/Config.lb5
-rw-r--r--src/southbridge/amd/cs5536_lx/chip.h53
-rw-r--r--src/southbridge/amd/cs5536_lx/cs5536.c331
-rw-r--r--src/southbridge/amd/cs5536_lx/cs5536.h6
-rw-r--r--src/southbridge/amd/cs5536_lx/cs5536_early_setup.c336
-rw-r--r--src/southbridge/amd/cs5536_lx/cs5536_early_smbus.c45
-rw-r--r--src/southbridge/amd/cs5536_lx/cs5536_ide.c30
-rw-r--r--src/southbridge/amd/cs5536_lx/cs5536_smbus.h180
-rw-r--r--src/southbridge/amd/cs5536_lx/cs5536_smbus2.h299
9 files changed, 1285 insertions, 0 deletions
diff --git a/src/southbridge/amd/cs5536_lx/Config.lb b/src/southbridge/amd/cs5536_lx/Config.lb
new file mode 100644
index 0000000000..3abdf5d4fa
--- /dev/null
+++ b/src/southbridge/amd/cs5536_lx/Config.lb
@@ -0,0 +1,5 @@
+config chip.h
+driver cs5536.o
+driver cs5536_usb.o
+#driver cs5536_pci.o
+#driver cs5536_ide.o
diff --git a/src/southbridge/amd/cs5536_lx/chip.h b/src/southbridge/amd/cs5536_lx/chip.h
new file mode 100644
index 0000000000..146e1d2621
--- /dev/null
+++ b/src/southbridge/amd/cs5536_lx/chip.h
@@ -0,0 +1,53 @@
+#ifndef _SOUTHBRIDGE_AMD_CS5536
+#define _SOUTHBRIDGE_AMD_CS5536
+
+#define MAX_UNWANTED_VPCI 10 /* increase if needed */
+
+extern struct chip_operations southbridge_amd_cs5536_ops;
+
+struct southbridge_amd_cs5536_config {
+ /* interrupt enable for LPC bus */
+ int lpc_serirq_enable; /* how to enable, e.g. 0x80 */
+ int lpc_irq; /* what to enable, e.g. 0x18 */
+ int enable_ide_nand_flash; /* if you are using nand flash instead of IDE drive */
+
+ /* following are IRQ numbers for various southbridge resources.
+ * these are configured and PCI headers are set */
+
+ int isa_irq; // f.0, 1022:2090
+ int flash_irq; // f.1, 1022:2091
+
+ // ide irq is tied to IRQ14, this can only be enabled or disabled
+ int enable_ide_irq; // f.2, 1022:2092
+
+ int audio_irq; // f.3, 1022:2093
+
+ int usb_irq; // f.4,5,6,7, 1022:2094
+ // only one irq source for all usb devices
+
+ // internal UART IRQs
+ int uart0_irq;
+ int uart1_irq;
+
+ /* GPIO to IRQ mapping, intended to use for PCI IRQ's.
+ * This only does physical mapping, no PCI headers are configured
+ * PCI configuration is mainboard-specific and should be done in mainboard.c
+ */
+ // pci IRQs A-D. Set this to 0 to disable.
+ int pci_int[4];
+ // and their GPIO pins
+ int pci_int_pin[4];
+
+
+ // Enable KEL keyboard IRQ2
+ int enable_kel_keyb_irq;
+ // Enable KEL mouse IRQ12
+ int enable_kel_mouse_irq;
+ // Configure KEL Emulation IRQ (input Y13)
+ int kel_emul_irq;
+
+ /* the following allow you to disable unwanted virtualized PCI devices */
+ unsigned long unwanted_vpci[MAX_UNWANTED_VPCI];
+};
+
+#endif /* _SOUTHBRIDGE_AMD_CS5536 */
diff --git a/src/southbridge/amd/cs5536_lx/cs5536.c b/src/southbridge/amd/cs5536_lx/cs5536.c
new file mode 100644
index 0000000000..803a5fbb6b
--- /dev/null
+++ b/src/southbridge/amd/cs5536_lx/cs5536.c
@@ -0,0 +1,331 @@
+
+#include <arch/io.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ops.h>
+#include <device/pci_ids.h>
+#include <console/console.h>
+#include <cpu/amd/lxdef.h>
+#include <cpu/x86/msr.h>
+#include "chip.h"
+
+// prototypes here, avoid warnings
+void setup_i8259(void);
+void pci_assign_irqs(unsigned bus, unsigned slot, const unsigned char pIntAtoD[4]);
+void print_conf(void);
+
+#define PIN_OPT_IDE (1ULL<<0) /* 0 for flash, 1 for IDE */
+
+/* Intended value for LBAR_FLSH0: 4KiB, enabled, MMIO, NAND, @0x20000000 */
+/* NOTE: no longer used, prune at some point */
+/* OOPS: steve's changes don't work, so we have to keep this */
+msr_t flsh1 = { .hi=0xFFFFF007, .lo=0x20000000};
+
+// ide is ENABLED by default (in early init), this disables it if neccesary
+// and enables flash
+static void enable_ide_nand_flash()
+{
+ msr_t msr;
+ printk_debug("cs5536: %s\n", __FUNCTION__);
+#if 1
+ printk_err("WARNING: using deprecated flash enable mechanism\n");
+ /* steve took this one out ... not sure if needed or not */
+ msr = rdmsr(MDD_LBAR_FLSH1);
+
+ if ( ((msr.hi) & 7) != 7) {
+ printk_debug("MDD_LBAR_FLSH1 was 0x%08x%08x\n", msr.hi,msr.lo);
+ wrmsr(MDD_LBAR_FLSH1, flsh1);
+ }
+ msr = rdmsr(MDD_LBAR_FLSH1);
+ printk_debug("MDD_LBAR_FLSH1 is 0x%08x%08x\n", msr.hi,msr.lo);
+#endif
+ msr = rdmsr(MDD_PIN_OPT);
+ if (msr.lo & PIN_OPT_IDE) {
+ printk_debug("MDD_PIN_OPT was 0x%08x%08x\n", msr.hi,msr.lo);
+ msr.lo &= ~PIN_OPT_IDE;
+ wrmsr(MDD_PIN_OPT, msr);
+ }
+ msr = rdmsr(MDD_PIN_OPT);
+ printk_debug("MDD_PIN_OPT is 0x%08x%08x\n", msr.hi,msr.lo);
+
+ msr = rdmsr(MDD_NANDF_DATA);
+ if (msr.lo != 0x00100010) {
+ printk_debug("MDD_NANDF_DATA was 0x%08x%08x\n", msr.hi,msr.lo);
+ msr.lo = 0x00100010;
+ wrmsr(MDD_NANDF_DATA, msr);
+ }
+ msr = rdmsr(MDD_NANDF_DATA);
+ printk_debug("MDD_NANDF_DATA is 0x%08x%08x\n", msr.hi,msr.lo);
+
+ msr = rdmsr(MDD_NADF_CNTL);
+ if (msr.lo != 0x0010) {
+ printk_debug("MDD_NADF_CNTL was 0x%08x%08x\n", msr.hi,msr.lo);
+ msr.lo = 0x0010;
+ wrmsr(MDD_NADF_CNTL, msr);
+ }
+ msr = rdmsr(MDD_NADF_CNTL);
+ printk_debug("MDD_NADF_CNTL is 0x%08x%08x\n", msr.hi,msr.lo);
+ printk_debug("cs5536: EXIT %s\n", __FUNCTION__);
+}
+
+/* note: this is a candidate for inclusion in src/devices/pci_device.c */
+// set pci headers to indicate correct IRQ number of the device
+void setup_irq(unsigned irq, unsigned level, unsigned bus, unsigned device, unsigned fn)
+{
+ if (irq)
+ {
+ unsigned devfn = PCI_DEVFN(device,fn);
+ device_t dev = dev_find_slot(bus, devfn);
+ if (dev)
+ {
+ printk_debug("%s: assigning IRQ %d to %x.%x (0x%x)\n",
+ __FUNCTION__, irq, device, fn, devfn);
+
+ pci_write_config8(dev, PCI_INTERRUPT_LINE, irq);
+ if (level) pci_level_irq(irq);
+ }
+ else
+ printk_err("%s: Can't find PCI device function 0x%x\n", __FUNCTION__, devfn);
+ }
+}
+
+// map an Y or Z irq source in programmable irq controller
+// dev 0..15 Y, 16...31 Z
+void map_pic_irq(unsigned int dev, unsigned int irq){
+ msr_t msr;
+ unsigned long mask;
+ unsigned long val;
+
+
+ mask = ~(0xF<<((dev&7)<<2));
+ val = irq<<((dev&7)<<2);
+
+ printk_debug("%s: mapping %d to src %d: mask %x val %x\n",
+ __FUNCTION__, irq, dev,mask,val);
+
+ switch (dev & 0x18){
+ case 0:
+ msr=rdmsr(MDD_IRQM_YLOW);
+ msr.lo = (msr.lo & mask) | val;
+ wrmsr(MDD_IRQM_YLOW,msr);
+ break;
+ case 8:
+ msr=rdmsr(MDD_IRQM_YHIGH);
+ msr.lo = (msr.lo & mask) | val;
+ wrmsr(MDD_IRQM_YHIGH,msr);
+ break;
+ case 16:
+ msr=rdmsr(MDD_IRQM_ZLOW);
+ msr.lo = (msr.lo & mask) | val;
+ wrmsr(MDD_IRQM_ZLOW,msr);
+ break;
+ case 24:
+ msr=rdmsr(MDD_IRQM_ZHIGH);
+ msr.lo = (msr.lo & mask) | val;
+ wrmsr(MDD_IRQM_ZHIGH,msr);
+ }
+}
+
+// map an GPIO pin to PIC Z source and that to an IRQ.
+void map_gpio_irq(unsigned int pin, unsigned int gpioirq, unsigned int irq, unsigned int invert){
+
+ unsigned long temp;
+ unsigned long mask;
+ unsigned long val;
+
+ mask = ~(0xF<<((pin&7)<<2));
+ val = gpioirq<<((pin&7)<<2);
+
+ // configure GPIO pin as INT source
+ outl(1<<(pin&0x0F), (pin<16)?GPIOL_INPUT_ENABLE:GPIOH_INPUT_ENABLE);
+ outl(1<<(pin&0x0F), (pin<16)?GPIOL_EVENTS_ENABLE:GPIOH_EVENTS_ENABLE);
+
+ if (invert) outl(1<<(pin&0x0F), (pin<16)?GPIOL_INPUT_INVERT_ENABLE:GPIOH_INPUT_INVERT_ENABLE);
+
+ // map current GPIO pin to PIC unrestricted Z GPIO irq source gpioirq
+ temp = inl((pin<16)?
+ ((pin<8)?GPIO_MAPPER_X:GPIO_MAPPER_Y):
+ ((pin<24)?GPIO_MAPPER_Z:GPIO_MAPPER_W));
+
+ outl((temp & mask)|val,
+ (pin<16)?
+ ((pin<8)?GPIO_MAPPER_X:GPIO_MAPPER_Y):
+ ((pin<24)?GPIO_MAPPER_Z:GPIO_MAPPER_W));
+
+ // map PIC unrestricted Z GPIO source i to IRQ needed
+ map_pic_irq(gpioirq+24,irq);
+}
+
+static void southbridge_init(struct device *dev)
+{
+ struct southbridge_amd_cs5536_config *sb = (struct southbridge_amd_cs5536_config *)dev->chip_info;
+ msr_t msr;
+ int i;
+
+ printk_spew(">> Entering cs5536.c: %s\n", __FUNCTION__);
+
+ /*
+ * struct device *gpiodev;
+ * unsigned short gpiobase = MDD_GPIO;
+ */
+
+ setup_i8259();
+
+ // at first, disable all primary IRQ inputs except timer, RTC and FPU
+ msr.lo=0x2101;
+ msr.hi=0;
+ wrmsr(MDD_IRQM_PRIM, msr);
+
+ // LPC bus IRQs are enabled here
+ if (sb->lpc_serirq_enable) {
+ msr.lo = sb->lpc_serirq_enable;
+ msr.hi = 0;
+ wrmsr(MDD_LPC_SIRQ, msr);
+ }
+ if (sb->lpc_irq) {
+ msr.lo = sb->lpc_irq;
+ msr.hi = 0;
+ wrmsr(MDD_IRQM_LPC, msr);
+ }
+
+ // GPIO to IRQ mapping (meant for PCI IRQs)
+ // here, only physical mapping is done.
+ // pci headers should be configured for all pci slots available in mainboard.c
+ // so that operating system can read correct irq number from there
+ for (i=0; i<3; i++){
+ if (sb->pci_int[i]){
+ printk_debug("cs5536: %s: Configuring PCI INT%c from GPIO %d to INT %d.\n",
+ __FUNCTION__, 'A'+i, sb->pci_int_pin[i], sb->pci_int[i]);
+ map_gpio_irq(sb->pci_int_pin[i], i, sb->pci_int[i], 1);
+ }
+ }
+/*
+// PCI IRQ mapping should work like this through vsa, but it doesn't
+ outl(0xAC1C, 0xFC53); //magic word to enable hidden register
+ outl(0xAC1C, 0x0009); //command: PCI_INT_AB
+ outl(0xAC1E,
+ (sb->pci_int[0]>0)?(sb->pci_int_pin[0]):0x21 |
+ (sb->pci_int[1]>0)?(sb->pci_int_pin[1]<<8):(0x21<<8)
+ );
+
+ outl(0x785C, sb->pci_int[0]|(sb->pci_int[1]<<8));
+*/
+
+ printk_debug("cs5536: %s: enable_ide_nand_flash is %d\n", __FUNCTION__, sb->enable_ide_nand_flash);
+ if (sb->enable_ide_nand_flash) {
+ enable_ide_nand_flash();
+ }
+
+ /* irq handling */
+ // setup_irq sets irq in pci headers only, no configuration is done.
+ // pci headers must be set, operating system reads IRQ numbers there.
+ // to disable, set IRQ=0
+
+ if (sb->isa_irq){
+ setup_irq(sb->isa_irq, 1, 0, 0xf, 0);
+ }
+
+ if (sb->flash_irq){
+ setup_irq(sb->flash_irq, 1, 0, 0xf, 1);
+ map_pic_irq(6,sb->flash_irq);
+ map_pic_irq(7,sb->flash_irq);
+ }
+
+ // IDE IRQ 14 (GPIO pin 2) can only be enabled or disabled
+ if (sb->enable_ide_irq){
+ setup_irq(14, 1, 0, 0xf, 2);
+
+ // set up IDE GPIO IRQ pin
+ outl(1<<2, GPIOL_INPUT_ENABLE);
+ outl(1<<2, GPIOL_IN_AUX1_SELECT);
+
+ // enable IDE IRQ in primary IRQ mask
+ msr=rdmsr(MDD_IRQM_PRIM);
+ msr.lo |= 0x4000;
+ wrmsr(MDD_IRQM_PRIM, msr);
+ }
+
+ if (sb->audio_irq){
+ map_pic_irq(4,sb->audio_irq);
+ setup_irq(sb->audio_irq, 1, 0, 0xf, 3);
+ }
+
+ if (sb->uart0_irq){
+ map_pic_irq(14,sb->uart0_irq);
+ }
+ if (sb->uart1_irq){
+ map_pic_irq(15,sb->uart1_irq);
+ }
+
+ if (sb->usb_irq){
+ setup_irq(sb->usb_irq, 1, 0, 0xf, 4);
+ setup_irq(sb->usb_irq, 1, 0, 0xf, 5);
+ setup_irq(sb->usb_irq, 1, 0, 0xf, 6);
+ setup_irq(sb->usb_irq, 1, 0, 0xf, 7);
+ map_pic_irq(2,sb->usb_irq);
+ }
+
+ // KEL (Keyboard Emulation Logic) IRQs
+ if (sb->enable_kel_keyb_irq){
+ msr=rdmsr(MDD_IRQM_PRIM);
+ msr.lo |= 0x0002;
+ wrmsr(MDD_IRQM_PRIM, msr);
+ }
+
+ if (sb->enable_kel_mouse_irq){
+ msr=rdmsr(MDD_IRQM_PRIM);
+ msr.lo |= 0x1000;
+ wrmsr(MDD_IRQM_PRIM, msr);
+ }
+
+ if (sb->kel_emul_irq){
+ map_pic_irq(13,sb->kel_emul_irq);
+ }
+
+
+
+
+ /* disable unwanted virtual PCI devices */
+ for (i = 0; (i < MAX_UNWANTED_VPCI) && (0 != sb->unwanted_vpci[i]); i++) {
+ printk_debug("Disabling VPCI device: 0x%08X\n", sb->unwanted_vpci[i]);
+ outl(sb->unwanted_vpci[i] + 0x7C, 0xCF8);
+ outl(0xDEADBEEF, 0xCFC);
+ }
+
+ /* What do we have there? */
+ printk_debug("\nChipset config after southbridge_init():\n");
+ print_conf();
+}
+
+void southbridge_enable(struct device *dev)
+{
+}
+
+static void cs5536_pci_dev_enable_resources(device_t dev)
+{
+ printk_spew(">> Entering cs5536.c: %s\n", __FUNCTION__);
+ pci_dev_enable_resources(dev);
+ enable_childrens_resources(dev);
+}
+
+static struct device_operations southbridge_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = cs5536_pci_dev_enable_resources,
+ .init = southbridge_init,
+ .scan_bus = scan_static_bus,
+};
+
+static struct pci_driver cs5536_pci_driver __pci_driver = {
+ .ops = &southbridge_ops,
+ .vendor = PCI_VENDOR_ID_AMD,
+ .device = PCI_DEVICE_ID_AMD_CS5536_ISA
+};
+
+struct chip_operations southbridge_amd_cs5536_ops = {
+ CHIP_NAME("AMD cs5536")
+ /* This only called when this device is listed in the
+ * static device tree.
+ */
+ .enable_dev = southbridge_enable,
+};
diff --git a/src/southbridge/amd/cs5536_lx/cs5536.h b/src/southbridge/amd/cs5536_lx/cs5536.h
new file mode 100644
index 0000000000..8a7453f82e
--- /dev/null
+++ b/src/southbridge/amd/cs5536_lx/cs5536.h
@@ -0,0 +1,6 @@
+#ifndef _CS5536_H
+#define _CS5536_H
+
+extern void southbridge_enable(device_t dev);
+
+#endif
diff --git a/src/southbridge/amd/cs5536_lx/cs5536_early_setup.c b/src/southbridge/amd/cs5536_lx/cs5536_early_setup.c
new file mode 100644
index 0000000000..e799db6763
--- /dev/null
+++ b/src/southbridge/amd/cs5536_lx/cs5536_early_setup.c
@@ -0,0 +1,336 @@
+
+/*
+ *
+ * cs5536_early_setup.c: Early chipset initialization for CS5536 companion device
+ *
+ *
+ * This file implements the initialization sequence documented in section 4.2 of
+ * AMD Geode GX Processor CS5536 Companion Device GoedeROM Porting Guide.
+ *
+ */
+
+#define CS5536_GLINK_PORT_NUM 0x02 /* the geode link port number to the CS5536 */
+#define CS5536_DEV_NUM 0x0F /* default PCI device number for CS5536 */
+
+
+/**
+ * By default, on cs5536 IDE is disabled and flash is enabled
+ * This function disables flash and enables IDE
+ */
+
+static void cs5536_enable_ide(void){
+ msr_t msr;
+ msr = __builtin_rdmsr(0x51400015);
+ msr.lo |= 0x00000001;
+ __builtin_wrmsr(0x51400015, msr.lo, msr.hi);
+}
+
+/**
+ * @brief Setup PCI IDSEL for CS5536
+ *
+ *
+ */
+
+static void cs5536_setup_extmsr(void)
+{
+ msr_t msr;
+
+ /* forward MSR access to CS5536_GLINK_PORT_NUM to CS5536_DEV_NUM */
+ msr.hi = 0x00000000;
+ msr.lo = 0x00000000;
+ if (CS5536_GLINK_PORT_NUM <= 4) {
+ msr.lo = CS5536_DEV_NUM << ((CS5536_GLINK_PORT_NUM - 1) * 8);
+ } else {
+ msr.hi = CS5536_DEV_NUM << ((CS5536_GLINK_PORT_NUM - 5) * 8);
+ }
+ wrmsr(0x5000201e, msr);
+}
+
+static void cs5536_setup_idsel(void)
+{
+ /* write IDSEL to the write once register at address 0x0000 */
+ outl(0x1 << (CS5536_DEV_NUM + 10), 0);
+}
+
+static void cs5536_usb_swapsif(void)
+{
+ msr_t msr;
+
+ msr = rdmsr(0x51600005);
+ //USB Serial short detect bit.
+ if (msr.hi & 0x10) {
+ /* We need to preserve bits 32,33,35 and not clear any BIST error, but clear the
+ * SERSHRT error bit */
+ msr.hi &= 0xFFFFFFFB;
+ wrmsr(0x51600005, msr);
+ }
+}
+
+static int cs5536_setup_iobase(void)
+{
+ msr_t msr;
+
+ /* setup LBAR for SMBus controller */
+ __builtin_wrmsr(0x5140000b, 0x00006000, 0x0000f001);
+ /* setup LBAR for GPIO */
+ __builtin_wrmsr(0x5140000c, 0x00006100, 0x0000f001);
+ /* setup LBAR for MFGPT */
+ __builtin_wrmsr(0x5140000d, 0x00006200, 0x0000f001);
+ /* setup LBAR for ACPI */
+ __builtin_wrmsr(0x5140000e, 0x00009c00, 0x0000f001);
+ /* setup LBAR for PM Support */
+ __builtin_wrmsr(0x5140000f, 0x00009d00, 0x0000f001);
+}
+
+static void cs5536_setup_power_bottun(void)
+{
+ /* not implemented yet */
+#if 0
+ pwrBtn_setup:
+ ;
+ ; Power Button Setup
+ ;
+ ;mov eax, 0C0020000h ; 4 seconds + lock
+ mov eax, 040020000h ; 4 seconds no lock
+ mov dx, PMLogic_BASE + 40h
+ out dx, eax
+
+ ; setup GPIO24, it is the external signal for 5536 vsb_work_aux
+ ; which controls all voltage rails except Vstandby & Vmem.
+ ; We need to enable, OUT_AUX1 and OUTPUT_ENABLE in this order.
+ ; If GPIO24 is not enabled then soft-off will not work.
+ mov dx, GPIOH_OUT_AUX1_SELECT
+ mov eax, GPIOH_24_SET
+ out dx, eax
+ mov dx, GPIOH_OUTPUT_ENABLE
+ out dx, eax
+
+#endif
+}
+
+static void cs5536_setup_gpio(void)
+{
+ uint32_t val;
+
+ /* setup GPIO pins 14/15 for SDA/SCL */
+ val = (1<<14 | 1<<15);
+ /* Output Enable */
+ outl(0x3fffc000, 0x6100 + 0x04);
+ //outl(val, 0x6100 + 0x04);
+ /* Output AUX1 */
+ outl(0x3fffc000, 0x6100 + 0x10);
+ //outl(val, 0x6100 + 0x10);
+ /* Input Enable */
+ //outl(0x0f5af0a5, 0x6100 + 0x20);
+ outl(0x3fffc000, 0x6100 + 0x20);
+ //outl(val, 0x6100 + 0x20);
+ /* Input AUX1 */
+ //outl(0x3ffbc004, 0x6100 + 0x34);
+ outl(0x3fffc000, 0x6100 + 0x34);
+ //outl(val, 0x6100 + 0x34);
+
+ /* GX3: Enable GPIO pins for UART2 */
+ outl(0x00000010, GPIOL_OUT_AUX1_SELECT);
+ outl(0x00000010, GPIOL_OUTPUT_ENABLE);
+ outl(0x00000008, GPIOL_IN_AUX1_SELECT);
+ outl(0x00000008, GPIOL_INPUT_ENABLE);
+
+#if 0
+ /* changes proposed by Ollie; we will test this later. */
+ /* setup GPIO pins 14/15 for SDA/SCL */
+ val = GPIOL_15_SET | GPIOL_14_SET;
+ /* Output Enable */
+ //outl(0x3fffc000, 0x6100 + 0x04);
+ outl(val, 0x6100 + 0x04);
+ /* Output AUX1 */
+ //outl(0x3fffc000, 0x6100 + 0x10);
+ outl(val, 0x6100 + 0x10);
+ /* Input Enable */
+ //outl(0x3fffc000, 0x6100 + 0x20);
+ outl(val, 0x6100 + 0x20);
+ /* Input AUX1 */
+ //outl(0x3fffc000, 0x6100 + 0x34);
+ outl(val, 0x6100 + 0x34);
+#endif
+}
+
+static void cs5536_disable_internal_uart(void)
+{
+ /* not implemented yet */
+#if 0
+ ; The UARTs default to enabled.
+ ; Disable and reset them and configure them later. (SIO init)
+ mov ecx, MDD_UART1_CONF
+ RDMSR
+ mov eax, 1h ; reset
+ WRMSR
+ mov eax, 0h ; disabled
+ WRMSR
+
+ mov ecx, MDD_UART2_CONF
+ RDMSR
+ mov eax, 1h ; reset
+ WRMSR
+ mov eax, 0h ; disabled
+ WRMSR
+
+#endif
+}
+
+static void cs5536_setup_cis_mode(void)
+{
+ msr_t msr;
+
+ /* setup CPU interface serial to mode C on both sides */
+ msr = __builtin_rdmsr(0x51000010);
+ msr.lo &= ~0x18;
+ msr.lo |= 0x10;
+ __builtin_wrmsr(0x51000010, msr.lo, msr.hi);
+ //Only do this if we are building for 5536
+ __builtin_wrmsr(0x54002010, 0x00000002, 0x00000000);
+}
+
+static void dummy(void)
+{
+}
+
+/* see page 412 of the cs5536 companion book */
+static int cs5536_setup_onchipuart(void)
+{
+ unsigned long m;
+
+ unsigned char n;
+
+ /*
+ * 1. Eanble GPIO 8 to OUT_AUX1, 9 to IN_AUX1
+ * GPIO LBAR + 0x04, LBAR + 0x10, LBAR + 0x20, LBAR + 34
+ * 2. Enable UART IO space in MDD
+ * MSR 0x51400014 bit 18:16
+ * 3. Enable UART controller
+ * MSR 0x5140003A bit 0, 1
+ * 4. IRQ routing on IRQ Mapper
+ * MSR 0x51400021 bit [27:24]
+ */
+ msr_t msr;
+
+ /* Bit 1 = DEVEN (device enable)
+ * Bit 4 = EN_BANKS (allow access to the upper banks)
+ */
+
+ msr.lo = (1 << 4) | (1 << 1);
+ msr.hi = 0;
+ /* enable COM1 */
+ //wrmsr(0x5140003a, msr);
+ /* GPIO8 - UART1_TX */
+ /* Set: Output Enable (0x4) */
+ m = inl(GPIOL_OUTPUT_ENABLE);
+ m |= GPIOL_8_SET;
+ m &= ~GPIOL_8_CLEAR;
+ //outl(m,GPIOL_OUTPUT_ENABLE);
+ /* Set: OUTAUX1 Select (0x10) */
+ m = inl(GPIOL_OUT_AUX1_SELECT);
+ m |= GPIOL_8_SET;
+ m &= ~GPIOL_8_CLEAR;
+ //outl(m,GPIOL_OUT_AUX1_SELECT);
+ /* Set: Pull Up (0x18) */
+ m = inl(GPIOL_PULLUP_ENABLE);
+ m |= GPIOL_8_SET;
+ m &= ~GPIOL_8_CLEAR;
+ /* GPIO9 - UART1_RX */
+ /* Set: Pull Up (0x18) */
+ m |= GPIOL_9_SET;
+ m &= ~GPIOL_9_CLEAR;
+ //outl(m,GPIOL_PULLUP_ENABLE);
+ /* Set: Input Enable (0x20) */
+ m = inl(GPIOL_INPUT_ENABLE);
+ m |= GPIOL_9_SET;
+ m &= ~GPIOL_9_CLEAR;
+ //outl(m,GPIOL_INPUT_ENABLE);
+ /* Set: INAUX1 Select (0x34) */
+ m = inl(GPIOL_IN_AUX1_SELECT);
+ m |= GPIOL_9_SET;
+ m &= ~GPIOL_9_CLEAR;
+ //outl(m,GPIOL_IN_AUX1_SELECT);
+
+ msr = rdmsr(MDD_LEG_IO);
+ msr.lo |= 0x7 << 16;
+ //wrmsr(MDD_LEG_IO,msr);
+
+ // GX3: my board has UART2 wired up ;)
+
+
+ // enable UART2 as COM1
+ msr = rdmsr(MDD_LEG_IO);
+ msr.lo |= 0x700000;
+ wrmsr(MDD_LEG_IO, msr);
+
+ // reset UART2
+ msr = rdmsr(MDD_UART2_CONF);
+ msr.lo = 1;
+ wrmsr(MDD_UART2_CONF, msr);
+
+ // clear reset UART2
+ msr.lo = 0;
+ wrmsr(MDD_UART2_CONF, msr);
+
+ // enable UART2
+ msr.lo = 2;
+ wrmsr(MDD_UART2_CONF, msr);
+
+
+ // Set DLAB
+ n = 0x80;
+ outb(n, TTYS0_BASE + 3);
+
+ // Baud rate divisor
+ n = 0x01;
+ outb(n, TTYS0_BASE);
+
+ // Line mode (8N1)
+ n = 0x03;
+ outb(n, TTYS0_BASE + 3);
+
+ // Clear DTR & RTS
+ n = 0x00;
+ outb(n, TTYS0_BASE + 4);
+
+}
+
+/* note: you can't do prints in here in most cases,
+ * and we don't want to hang on serial, so they are
+ * commented out
+ */
+static int cs5536_early_setup(void)
+{
+ msr_t msr;
+
+ cs5536_setup_extmsr();
+
+/* msr = rdmsr(GLCP_SYS_RSTPLL);
+ if (msr.lo & (0x3f << 26)) {
+ // PLL is already set and we are reboot from PLL reset
+ //print_debug("reboot from BIOS reset\n\r");
+ return;
+ }*/
+
+ //print_debug("Setup idsel\r\n");
+ cs5536_setup_idsel();
+ //print_debug("Setup iobase\r\n");
+ cs5536_usb_swapsif();
+ cs5536_setup_iobase();
+ //print_debug("Setup gpio\r\n");
+ cs5536_setup_gpio();
+ //print_debug("Setup cis_mode\r\n");
+ cs5536_setup_cis_mode();
+ //print_debug("Setup smbus\r\n");
+ cs5536_enable_smbus();
+
+ // ide/flash bit goes to default on reset
+ // this value depends on boot straps
+ // lets set it to known enabled value
+ // later, cs5536_enable_ide_nand_flash changes it if needed.
+ //cs5536_enable_ide();
+
+
+ dummy();
+}
diff --git a/src/southbridge/amd/cs5536_lx/cs5536_early_smbus.c b/src/southbridge/amd/cs5536_lx/cs5536_early_smbus.c
new file mode 100644
index 0000000000..0605d0cb82
--- /dev/null
+++ b/src/southbridge/amd/cs5536_lx/cs5536_early_smbus.c
@@ -0,0 +1,45 @@
+#include "cs5536_smbus.h"
+
+#define SMBUS_IO_BASE 0x6000
+
+/* initialization for SMBus Controller */
+static int cs5536_enable_smbus(void)
+{
+ unsigned char val;
+
+ /* reset SMBUS controller */
+ outb(0, SMBUS_IO_BASE + SMB_CTRL2);
+
+ /* Set SCL freq and enable SMB controller */
+ val = inb(SMBUS_IO_BASE + SMB_CTRL2);
+ val |= ((0x20 << 1) | SMB_CTRL2_ENABLE);
+ outb(val, SMBUS_IO_BASE + SMB_CTRL2);
+
+ /* Setup SMBus host controller address to 0xEF */
+ val = inb(SMBUS_IO_BASE + SMB_ADD);
+ val |= (0xEF | SMB_ADD_SAEN);
+ outb(val, SMBUS_IO_BASE + SMB_ADD);
+}
+
+static int smbus_read_byte(unsigned device, unsigned address)
+{
+ return do_smbus_read_byte(SMBUS_IO_BASE, device, address-1);
+}
+
+#if 0
+static int smbus_recv_byte(unsigned device)
+{
+ return do_smbus_recv_byte(SMBUS_IO_BASE, device);
+}
+
+static int smbus_send_byte(unsigned device, unsigned char val)
+{
+ return do_smbus_send_byte(SMBUS_IO_BASE, device, val);
+}
+
+
+static int smbus_write_byte(unsigned device, unsigned address, unsigned char val)
+{
+ return do_smbus_write_byte(SMBUS_IO_BASE, device, address, val);
+}
+#endif
diff --git a/src/southbridge/amd/cs5536_lx/cs5536_ide.c b/src/southbridge/amd/cs5536_lx/cs5536_ide.c
new file mode 100644
index 0000000000..284b5037d8
--- /dev/null
+++ b/src/southbridge/amd/cs5536_lx/cs5536_ide.c
@@ -0,0 +1,30 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "cs5536.h"
+
+static void ide_init(struct device *dev)
+{
+ printk_spew("cs5536_ide: %s\n", __FUNCTION__);
+}
+
+static void ide_enable(struct device *dev)
+{
+ printk_spew("cs5536_ide: %s\n", __FUNCTION__);
+}
+
+static struct device_operations ide_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = ide_init,
+ .enable = ide_enable,
+};
+
+static struct pci_driver ide_driver __pci_driver = {
+ .ops = &ide_ops,
+ .vendor = PCI_VENDOR_ID_AMD,
+ .device = PCI_DEVICE_ID_AMD_CS5536_IDE,
+};
diff --git a/src/southbridge/amd/cs5536_lx/cs5536_smbus.h b/src/southbridge/amd/cs5536_lx/cs5536_smbus.h
new file mode 100644
index 0000000000..9cf55ba29c
--- /dev/null
+++ b/src/southbridge/amd/cs5536_lx/cs5536_smbus.h
@@ -0,0 +1,180 @@
+//#include <device/smbus_def.h>
+#define SMBUS_ERROR -1
+#define SMBUS_WAIT_UNTIL_READY_TIMEOUT -2
+#define SMBUS_WAIT_UNTIL_DONE_TIMEOUT -3
+
+#define SMB_SDA 0x00
+#define SMB_STS 0x01
+#define SMB_CTRL_STS 0x02
+#define SMB_CTRL1 0x03
+#define SMB_ADD 0x04
+#define SMB_CTRL2 0x05
+#define SMB_CTRL3 0x06
+
+#define SMB_STS_SLVSTP (0x01 << 7)
+#define SMB_STS_SDAST (0x01 << 6)
+#define SMB_STS_BER (0x01 << 5)
+#define SMB_STS_NEGACK (0x01 << 4)
+#define SMB_STS_STASTR (0x01 << 3)
+#define SMB_STS_NMATCH (0x01 << 2)
+#define SMB_STS_MASTER (0x01 << 1)
+#define SMB_STS_XMIT (0x01 << 0)
+
+#define SMB_CSTS_TGSCL (0x01 << 5)
+#define SMB_CSTS_TSDA (0x01 << 4)
+#define SMB_CSTS_GCMTCH (0x01 << 3)
+#define SMB_CSTS_MATCH (0x01 << 2)
+#define SMB_CSTS_BB (0x01 << 1)
+#define SMB_CSTS_BUSY (0x01 << 0)
+
+#define SMB_CTRL1_STASTRE (0x01 << 7)
+#define SMB_CTRL1_NMINTE (0x01 << 6)
+#define SMB_CTRL1_GCMEN (0x01 << 5)
+#define SMB_CTRL1_ACK (0x01 << 4)
+#define SMB_CTRL1_RSVD (0x01 << 3)
+#define SMB_CTRL1_INTEN (0x01 << 2)
+#define SMB_CTRL1_STOP (0x01 << 1)
+#define SMB_CTRL1_START (0x01 << 0)
+
+#define SMB_ADD_SAEN (0x01 << 7)
+
+#define SMB_CTRL2_ENABLE 0x01
+
+#define SMBUS_TIMEOUT (100*1000*10)
+#define SMBUS_STATUS_MASK 0xfbff
+
+#define SMBUS_IO_BASE 0x6000
+
+static void smbus_delay(void)
+{
+ outb(0x80, 0x80);
+}
+
+/* generate a smbus start condition */
+static int smbus_start_condition(unsigned smbus_io_base)
+{
+ unsigned char val;
+ unsigned long loops;
+ loops = SMBUS_TIMEOUT;
+
+ /* issue a START condition */
+ val = inb(smbus_io_base + SMB_CTRL1);
+ outb(val | SMB_CTRL1_START, smbus_io_base + SMB_CTRL1);
+
+ /* check for bus conflict */
+ val = inb(smbus_io_base + SMB_STS);
+ if ((val & SMB_STS_BER) != 0)
+ return SMBUS_ERROR;
+
+ /* check for SDA status */
+ do {
+ smbus_delay();
+ val = inw(smbus_io_base + SMB_STS);
+ if ((val & SMB_STS_SDAST) != 0) {
+ break;
+ }
+ } while(--loops);
+ return loops?0:SMBUS_WAIT_UNTIL_READY_TIMEOUT;
+}
+
+static int smbus_check_stop_condition(unsigned smbus_io_base)
+{
+ unsigned char val;
+ unsigned long loops;
+ loops = SMBUS_TIMEOUT;
+ /* check for SDA status */
+ do {
+ smbus_delay();
+ val = inw(smbus_io_base + SMB_CTRL1);
+ if ((val & SMB_CTRL1_STOP) == 0) {
+ break;
+ }
+ } while(--loops);
+ return loops?0:SMBUS_WAIT_UNTIL_READY_TIMEOUT;
+}
+
+static int smbus_stop_condition(unsigned smbus_io_base)
+{
+ unsigned char val;
+ val = inb(smbus_io_base + SMB_CTRL1);
+ outb(SMB_CTRL1_STOP, smbus_io_base + SMB_CTRL1);
+}
+
+static int smbus_send_slave_address(unsigned smbus_io_base, unsigned char device)
+{
+ unsigned char val;
+ unsigned long loops;
+ loops = SMBUS_TIMEOUT;
+
+ /* send the slave address */
+ outb(device, smbus_io_base + SMB_SDA);
+
+ /* check for bus conflict and NACK */
+ val = inb(smbus_io_base + SMB_STS);
+ if (((val & SMB_STS_BER) != 0) ||
+ ((val & SMB_STS_NEGACK) != 0))
+ return SMBUS_ERROR;
+
+ /* check for SDA status */
+ do {
+ smbus_delay();
+ val = inw(smbus_io_base + SMB_STS);
+ if ((val & SMB_STS_SDAST) != 0) {
+ break;
+ }
+ } while(--loops);
+ return loops?0:SMBUS_WAIT_UNTIL_READY_TIMEOUT;
+}
+
+static int smbus_send_command(unsigned smbus_io_base, unsigned char command)
+{
+ unsigned char val;
+ unsigned long loops;
+ loops = SMBUS_TIMEOUT;
+
+ /* send the command */
+ outb(command, smbus_io_base + SMB_SDA);
+
+ /* check for bus conflict and NACK */
+ val = inb(smbus_io_base + SMB_STS);
+ if (((val & SMB_STS_BER) != 0) ||
+ ((val & SMB_STS_NEGACK) != 0))
+ return SMBUS_ERROR;
+
+ /* check for SDA status */
+ do {
+ smbus_delay();
+ val = inw(smbus_io_base + SMB_STS);
+ if ((val & SMB_STS_SDAST) != 0) {
+ break;
+ }
+ } while(--loops);
+ return loops?0:SMBUS_WAIT_UNTIL_READY_TIMEOUT;
+}
+
+static unsigned char do_smbus_read_byte(unsigned smbus_io_base, unsigned char device, unsigned char address)
+{
+ unsigned char val, val1;
+
+ smbus_check_stop_condition(smbus_io_base);
+
+ smbus_start_condition(smbus_io_base);
+
+ smbus_send_slave_address(smbus_io_base, device);
+
+ smbus_send_command(smbus_io_base, address);
+
+ smbus_start_condition(smbus_io_base);
+
+ smbus_send_slave_address(smbus_io_base, device | 0x01);
+
+ /* send NACK to slave */
+ val = inb(smbus_io_base + SMB_CTRL1);
+ outb(val | SMB_CTRL1_ACK, smbus_io_base + SMB_CTRL1);
+
+ val = inb(smbus_io_base + SMB_SDA);
+
+ //smbus_stop_condition(smbus_io_base);
+
+ return val;
+}
diff --git a/src/southbridge/amd/cs5536_lx/cs5536_smbus2.h b/src/southbridge/amd/cs5536_lx/cs5536_smbus2.h
new file mode 100644
index 0000000000..3f5dad002e
--- /dev/null
+++ b/src/southbridge/amd/cs5536_lx/cs5536_smbus2.h
@@ -0,0 +1,299 @@
+//#include <device/smbus_def.h>
+#define SMBUS_ERROR -1
+#define SMBUS_WAIT_UNTIL_READY_TIMEOUT -2
+#define SMBUS_WAIT_UNTIL_DONE_TIMEOUT -3
+
+#define SMB_SDA 0x00
+#define SMB_STS 0x01
+#define SMB_CTRL_STS 0x02
+#define SMB_CTRL1 0x03
+#define SMB_ADD 0x04
+#define SMB_CTRL2 0x05
+#define SMB_CTRL3 0x06
+
+#define SMB_STS_SLVSTP (0x01 << 7)
+#define SMB_STS_SDAST (0x01 << 6)
+#define SMB_STS_BER (0x01 << 5)
+#define SMB_STS_NEGACK (0x01 << 4)
+#define SMB_STS_STASTR (0x01 << 3)
+#define SMB_STS_NMATCH (0x01 << 2)
+#define SMB_STS_MASTER (0x01 << 1)
+#define SMB_STS_XMIT (0x01 << 0)
+
+#define SMB_CSTS_TGSCL (0x01 << 5)
+#define SMB_CSTS_TSDA (0x01 << 4)
+#define SMB_CSTS_GCMTCH (0x01 << 3)
+#define SMB_CSTS_MATCH (0x01 << 2)
+#define SMB_CSTS_BB (0x01 << 1)
+#define SMB_CSTS_BUSY (0x01 << 0)
+
+#define SMB_CTRL1_STASTRE (0x01 << 7)
+#define SMB_CTRL1_NMINTE (0x01 << 6)
+#define SMB_CTRL1_GCMEN (0x01 << 5)
+#define SMB_CTRL1_ACK (0x01 << 4)
+#define SMB_CTRL1_RSVD (0x01 << 3)
+#define SMB_CTRL1_INTEN (0x01 << 2)
+#define SMB_CTRL1_STOP (0x01 << 1)
+#define SMB_CTRL1_START (0x01 << 0)
+
+#define SMB_ADD_SAEN (0x01 << 7)
+
+#define SMB_CTRL2_ENABLE 0x01
+
+#define SMBUS_TIMEOUT (100*1000*10)
+#define SMBUS_STATUS_MASK 0xfbff
+
+#define SMBUS_IO_BASE 0x6000
+
+static void smbus_delay(void)
+{
+ outb(0x80, 0x80);
+}
+
+static int smbus_wait(unsigned smbus_io_base) {
+ unsigned long loops = SMBUS_TIMEOUT;
+ unsigned char val;
+
+ do {
+ smbus_delay();
+ val = inb(smbus_io_base + SMB_STS);
+ if ((val & SMB_STS_SDAST) != 0)
+ break;
+ if (val & (SMB_STS_BER | SMB_STS_NEGACK)) {
+ printk_debug("SMBUS WAIT ERROR %x\n", val);
+ return SMBUS_ERROR;
+ }
+ } while(--loops);
+
+ outb(0, smbus_io_base + SMB_STS);
+ return loops ? 0 : SMBUS_WAIT_UNTIL_READY_TIMEOUT;
+}
+
+static int smbus_write(unsigned smbus_io_base, unsigned char byte) {
+
+ outb(byte, smbus_io_base + SMB_SDA);
+ return smbus_wait(smbus_io_base);
+}
+
+/* generate a smbus start condition */
+static int smbus_start_condition(unsigned smbus_io_base)
+{
+ unsigned char val;
+
+ /* issue a START condition */
+ val = inb(smbus_io_base + SMB_CTRL1);
+ outb(val | SMB_CTRL1_START, smbus_io_base + SMB_CTRL1);
+
+ /* check for bus conflict */
+ val = inb(smbus_io_base + SMB_STS);
+ if ((val & SMB_STS_BER) != 0)
+ return SMBUS_ERROR;
+
+ return smbus_wait(smbus_io_base);
+}
+
+static int smbus_check_stop_condition(unsigned smbus_io_base)
+{
+ unsigned char val;
+ unsigned long loops;
+ loops = SMBUS_TIMEOUT;
+ /* check for SDA status */
+ do {
+ smbus_delay();
+ val = inb(smbus_io_base + SMB_CTRL1);
+ if ((val & SMB_CTRL1_STOP) == 0) {
+ break;
+ }
+ } while(--loops);
+ return loops?0:SMBUS_WAIT_UNTIL_READY_TIMEOUT;
+
+ /* Make sure everything is cleared and ready to go */
+
+ val = inb(smbus_io_base + SMB_CTRL1);
+ outb(val & ~(SMB_CTRL1_STASTRE | SMB_CTRL1_NMINTE),
+ smbus_io_base + SMB_CTRL1);
+
+ outb(SMB_STS_BER | SMB_STS_NEGACK | SMB_STS_STASTR,
+ smbus_io_base + SMB_STS);
+
+ val = inb(smbus_io_base + SMB_CTRL_STS);
+ outb(val | SMB_CSTS_BB, smbus_io_base + SMB_CTRL_STS);
+}
+
+static int smbus_stop_condition(unsigned smbus_io_base)
+{
+ unsigned char val;
+ val = inb(smbus_io_base + SMB_CTRL1);
+ outb(SMB_CTRL1_STOP, smbus_io_base + SMB_CTRL1);
+
+ return 0;
+}
+
+static int smbus_ack(unsigned smbus_io_base, int state)
+{
+ unsigned char val = inb(smbus_io_base + SMB_CTRL1);
+
+ if (state)
+ outb(val | SMB_CTRL1_ACK, smbus_io_base + SMB_CTRL1);
+ else
+ outb(val & ~SMB_CTRL1_ACK, smbus_io_base + SMB_CTRL1);
+
+ return 0;
+}
+
+static int smbus_send_slave_address(unsigned smbus_io_base, unsigned char device)
+{
+ unsigned char val;
+
+ /* send the slave address */
+ outb(device, smbus_io_base + SMB_SDA);
+
+ /* check for bus conflict and NACK */
+ val = inb(smbus_io_base + SMB_STS);
+ if (((val & SMB_STS_BER) != 0) ||
+ ((val & SMB_STS_NEGACK) != 0)) {
+ printk_debug("SEND SLAVE ERROR (%x)\n", val);
+ return SMBUS_ERROR;
+ }
+ return smbus_wait(smbus_io_base);
+}
+
+static int smbus_send_command(unsigned smbus_io_base, unsigned char command)
+{
+ unsigned char val;
+
+ /* send the command */
+ outb(command, smbus_io_base + SMB_SDA);
+
+ /* check for bus conflict and NACK */
+ val = inb(smbus_io_base + SMB_STS);
+ if (((val & SMB_STS_BER) != 0) ||
+ ((val & SMB_STS_NEGACK) != 0))
+ return SMBUS_ERROR;
+
+ return smbus_wait(smbus_io_base);
+}
+
+static void _doread(unsigned smbus_io_base, unsigned char device,
+ unsigned char address, unsigned char *data, int count)
+{
+ int ret;
+ int index = 0;
+ unsigned char val;
+
+ if ((ret = smbus_check_stop_condition(smbus_io_base)))
+ goto err;
+
+ index++;
+
+ if ((ret = smbus_start_condition(smbus_io_base)))
+ goto err;
+
+ index++; /* 2 */
+ if ((ret = smbus_send_slave_address(smbus_io_base, device)))
+ goto err;
+
+ index++;
+ if ((ret = smbus_send_command(smbus_io_base, address)))
+ goto err;
+
+ index++;
+ if ((ret = smbus_start_condition(smbus_io_base)))
+ goto err;
+
+ /* Clear the ack for multiple byte reads */
+ smbus_ack(smbus_io_base, (count == 1) ? 1 : 0);
+
+ index++;
+ if ((ret = smbus_send_slave_address(smbus_io_base, device | 0x01)))
+ goto err;
+
+ while(count) {
+ /* Set the ACK if this is the next to last byte */
+ smbus_ack(smbus_io_base, (count == 2) ? 1 : 0);
+
+ /* Set the stop bit if this is the last byte to read */
+
+ if (count == 1)
+ smbus_stop_condition(smbus_io_base);
+
+ val = inb(smbus_io_base + SMB_SDA);
+ *data++ = val;
+
+ if (count > 1) {
+ int ret = smbus_wait(smbus_io_base);
+ if (ret)
+ return ret;
+ }
+
+ count--;
+ }
+
+ return;
+
+ err:
+ printk_debug("SMBUS READ ERROR (%d): %d\n", index, ret);
+}
+
+static unsigned char do_smbus_read_byte(unsigned smbus_io_base,
+ unsigned char device,
+ unsigned char address)
+{
+ unsigned char val = 0;
+ _doread(smbus_io_base, device, address, &val, sizeof(val));
+ return val;
+}
+
+static unsigned short do_smbus_read_word(unsigned smbus_io_base,
+ unsigned char device, unsigned char address)
+{
+ unsigned short val = 0;
+ _doread(smbus_io_base, device, address, (unsigned char *) &val,
+ sizeof(val));
+ return val;
+}
+
+static int _dowrite(unsigned smbus_io_base, unsigned char device,
+ unsigned char address, unsigned char *data, int count) {
+
+ int ret;
+
+ if ((ret = smbus_check_stop_condition(smbus_io_base)))
+ goto err;
+
+ if ((ret = smbus_start_condition(smbus_io_base)))
+ goto err;
+
+ if ((ret = smbus_send_slave_address(smbus_io_base, device)))
+ goto err;
+
+ if ((ret = smbus_send_command(smbus_io_base, address)))
+ goto err;
+
+ while(count) {
+ if ((ret = smbus_write(smbus_io_base, *data++)))
+ goto err;
+ count--;
+ }
+
+ smbus_stop_condition(smbus_io_base);
+ return 0;
+
+ err:
+ printk_debug("SMBUS WRITE ERROR: %d\n", ret);
+ return -1;
+}
+
+
+static int do_smbus_write_byte(unsigned smbus_io_base, unsigned char device,
+ unsigned char address, unsigned char data)
+{
+ return _dowrite(smbus_io_base, device, address,
+ (unsigned char *) &data, 1);
+}
+
+static int do_smbus_write_word(unsigned smbus_io_base, unsigned char device, unsigned char address,
+ unsigned short data)
+{
+ return _dowrite(smbus_io_base, device ,address, (unsigned char *) &data, 2);
+}
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-25 04:58:03 +0000