diff options
Diffstat (limited to 'src')
21 files changed, 83 insertions, 18 deletions
diff --git a/src/Kconfig b/src/Kconfig index 690a1d4864..a61efe1a8e 100644 --- a/src/Kconfig +++ b/src/Kconfig @@ -736,4 +736,43 @@ config ID_SECTION_OFFSET hex default 0x10 +# The four POWER_BUTTON_DEFAULT_ENABLE, POWER_BUTTON_DEFAULT_DISABLE, +# POWER_BUTTON_FORCE_ENABLE and POWER_BUTTON_FORCE_DISABLE options are +# mutually exclusive. One of these options must be selected in the +# mainboard Kconfig if the chipset supports enabling and disabling of +# the power button. Chipset code uses the ENABLE_POWER_BUTTON option set +# in mainboard/Kconfig to know if the button should be enabled or not. + +config POWER_BUTTON_DEFAULT_ENABLE + def_bool n + help + Select when the board has a power button which can optionally be + disabled by the user. + +config POWER_BUTTON_DEFAULT_DISABLE + def_bool n + help + Select when the board has a power button which can optionally be + enabled by the user, e.g. when the board ships with a jumper over + the power switch contacts. + +config POWER_BUTTON_FORCE_ENABLE + def_bool n + help + Select when the board requires that the power button is always + enabled. + +config POWER_BUTTON_FORCE_DISABLE + def_bool n + help + Select when the board requires that the power button is always + disabled, e.g. when it has been hardwired to ground. + +config POWER_BUTTON_IS_OPTIONAL + bool + default y if POWER_BUTTON_DEFAULT_ENABLE || POWER_BUTTON_DEFAULT_DISABLE + default n if !(POWER_BUTTON_DEFAULT_ENABLE || POWER_BUTTON_DEFAULT_DISABLE) + help + Internal option that controls ENABLE_POWER_BUTTON visibility. + source src/Kconfig.deprecated_options diff --git a/src/mainboard/Kconfig b/src/mainboard/Kconfig index db1112826d..ca0d74d45d 100644 --- a/src/mainboard/Kconfig +++ b/src/mainboard/Kconfig @@ -247,4 +247,22 @@ config ROM_SIZE default 0x200000 if COREBOOT_ROMSIZE_KB_2048 default 0x400000 if COREBOOT_ROMSIZE_KB_4096 +config ENABLE_POWER_BUTTON + bool "Enable the power button" if POWER_BUTTON_IS_OPTIONAL + default y if POWER_BUTTON_DEFAULT_ENABLE + default n if POWER_BUTTON_DEFAULT_DISABLE + help + The selected mainboard can optionally have the power button tied + to ground with a jumper so that the button appears to be + constantly depressed. If this option is enabled and the jumper is + installed then the board will turn on, but turn off again after a + short timeout, usually 4 seconds. + + Select Y here if you have removed the jumper and want to use an + actual power button. Select N if you have the jumper installed. + +config ENABLE_POWER_BUTTON + def_bool y if !POWER_BUTTON_IS_OPTIONAL && POWER_BUTTON_FORCE_ENABLE + def_bool n if !POWER_BUTTON_IS_OPTIONAL && POWER_BUTTON_FORCE_DISABLE + endmenu diff --git a/src/mainboard/amd/db800/Kconfig b/src/mainboard/amd/db800/Kconfig index e1b94e9011..834e08589c 100644 --- a/src/mainboard/amd/db800/Kconfig +++ b/src/mainboard/amd/db800/Kconfig @@ -11,6 +11,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select PIRQ_ROUTE select UDELAY_TSC select BOARD_ROMSIZE_KB_256 + select POWER_BUTTON_FORCE_ENABLE config MAINBOARD_DIR string diff --git a/src/mainboard/amd/norwich/Kconfig b/src/mainboard/amd/norwich/Kconfig index 3dc214f00d..b265eeb103 100644 --- a/src/mainboard/amd/norwich/Kconfig +++ b/src/mainboard/amd/norwich/Kconfig @@ -10,6 +10,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select PIRQ_ROUTE select UDELAY_TSC select BOARD_ROMSIZE_KB_256 + select POWER_BUTTON_FORCE_ENABLE config MAINBOARD_DIR string diff --git a/src/mainboard/amd/rumba/Kconfig b/src/mainboard/amd/rumba/Kconfig index beda2bd5b2..a06650cc0f 100644 --- a/src/mainboard/amd/rumba/Kconfig +++ b/src/mainboard/amd/rumba/Kconfig @@ -27,6 +27,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select UDELAY_TSC select HAVE_PIRQ_TABLE select BOARD_ROMSIZE_KB_256 + select POWER_BUTTON_FORCE_ENABLE config MAINBOARD_DIR string diff --git a/src/mainboard/artecgroup/dbe61/Kconfig b/src/mainboard/artecgroup/dbe61/Kconfig index 52669294f7..846000ccad 100644 --- a/src/mainboard/artecgroup/dbe61/Kconfig +++ b/src/mainboard/artecgroup/dbe61/Kconfig @@ -10,6 +10,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select PIRQ_ROUTE select UDELAY_TSC select BOARD_ROMSIZE_KB_256 + select POWER_BUTTON_FORCE_DISABLE config MAINBOARD_DIR string diff --git a/src/mainboard/digitallogic/msm800sev/Kconfig b/src/mainboard/digitallogic/msm800sev/Kconfig index a082b1fe01..444023b2bd 100644 --- a/src/mainboard/digitallogic/msm800sev/Kconfig +++ b/src/mainboard/digitallogic/msm800sev/Kconfig @@ -11,6 +11,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select PIRQ_ROUTE select UDELAY_TSC select BOARD_ROMSIZE_KB_256 + select POWER_BUTTON_FORCE_ENABLE config MAINBOARD_DIR string diff --git a/src/mainboard/iei/pcisa-lx-800-r10/Kconfig b/src/mainboard/iei/pcisa-lx-800-r10/Kconfig index a6f5126633..e393609c88 100644 --- a/src/mainboard/iei/pcisa-lx-800-r10/Kconfig +++ b/src/mainboard/iei/pcisa-lx-800-r10/Kconfig @@ -10,6 +10,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select HAVE_PIRQ_TABLE select PIRQ_ROUTE select BOARD_ROMSIZE_KB_256 + select POWER_BUTTON_FORCE_ENABLE config MAINBOARD_DIR string diff --git a/src/mainboard/lippert/hurricane-lx/Kconfig b/src/mainboard/lippert/hurricane-lx/Kconfig index 027988f959..9b20aa0759 100644 --- a/src/mainboard/lippert/hurricane-lx/Kconfig +++ b/src/mainboard/lippert/hurricane-lx/Kconfig @@ -29,11 +29,20 @@ config IRQ_SLOT_COUNT config BOARD_OLD_REVISION bool "Board is old pre-3.0 revision" default n + select POWER_BUTTON_DEFAULT_DISABLE help Look on the bottom side for a number like 406-0001-30. The last 2 digits state the PCB revision (3.0 in this example). For 2.0 or older boards choose Y, for 3.0 and newer say N. + Old revision boards need a jumper shorting the power button to + power on automatically. You may enable the button only after this + jumper has been removed. New revision boards are not restricted + in this way, and always have the power button enabled. + +config POWER_BUTTON_FORCE_ENABLE + def_bool y if !BOARD_OLD_REVISION + config ONBOARD_UARTS_RS485 bool "Switch on-board serial ports to RS485" default n diff --git a/src/mainboard/lippert/hurricane-lx/romstage.c b/src/mainboard/lippert/hurricane-lx/romstage.c index 018f353fd0..b7314bf06f 100644 --- a/src/mainboard/lippert/hurricane-lx/romstage.c +++ b/src/mainboard/lippert/hurricane-lx/romstage.c @@ -147,14 +147,7 @@ void main(unsigned long bist) cpuRegInit(0, DIMM0, DIMM1, DRAM_TERMINATED); -#if CONFIG_BOARD_OLD_REVISION - /* - * Old revision boards need a jumper shorting the power button to power - * on automatically. So we must disable the button's fail-safe function, - * or the board will shut down after 4 s. - */ - outl(0, PMS_IO_BASE + PM_FSD); // Fail-Save Delay register -#else +#if !CONFIG_BOARD_OLD_REVISION int err; /* bit0 = Spread Spectrum */ if ((err = smc_send_config(SMC_CONFIG))) { diff --git a/src/mainboard/lippert/literunner-lx/Kconfig b/src/mainboard/lippert/literunner-lx/Kconfig index 482f571e8d..7b45d36ea1 100644 --- a/src/mainboard/lippert/literunner-lx/Kconfig +++ b/src/mainboard/lippert/literunner-lx/Kconfig @@ -14,6 +14,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy # Board is equipped with a 1 MB SPI flash, however, due to limitations # of the IT8712F Super I/O, only the top 512 KB are directly mapped. select BOARD_ROMSIZE_KB_512 + select POWER_BUTTON_FORCE_ENABLE config MAINBOARD_DIR string diff --git a/src/mainboard/lippert/roadrunner-lx/Kconfig b/src/mainboard/lippert/roadrunner-lx/Kconfig index 44326d193f..4e29742b81 100644 --- a/src/mainboard/lippert/roadrunner-lx/Kconfig +++ b/src/mainboard/lippert/roadrunner-lx/Kconfig @@ -13,6 +13,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy # Standard chip is a 512 KB FWH. Replacing it with a 1 MB # SST 49LF008A is possible. select BOARD_ROMSIZE_KB_512 + select POWER_BUTTON_FORCE_ENABLE config MAINBOARD_DIR string diff --git a/src/mainboard/lippert/spacerunner-lx/Kconfig b/src/mainboard/lippert/spacerunner-lx/Kconfig index 7526d1ecb4..f273d6cf56 100644 --- a/src/mainboard/lippert/spacerunner-lx/Kconfig +++ b/src/mainboard/lippert/spacerunner-lx/Kconfig @@ -14,6 +14,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy # Board is equipped with a 1 MB SPI flash, however, due to limitations # of the IT8712F Super I/O, only the top 512 KB are directly mapped. select BOARD_ROMSIZE_KB_512 + select POWER_BUTTON_FORCE_ENABLE config MAINBOARD_DIR string diff --git a/src/mainboard/pcengines/alix1c/Kconfig b/src/mainboard/pcengines/alix1c/Kconfig index b10095c902..0a016a54f5 100644 --- a/src/mainboard/pcengines/alix1c/Kconfig +++ b/src/mainboard/pcengines/alix1c/Kconfig @@ -11,6 +11,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select PIRQ_ROUTE select UDELAY_TSC select BOARD_ROMSIZE_KB_512 + select POWER_BUTTON_DEFAULT_DISABLE config MAINBOARD_DIR string diff --git a/src/mainboard/pcengines/alix2d/Kconfig b/src/mainboard/pcengines/alix2d/Kconfig index bb54d1cad1..264f5d9e97 100644 --- a/src/mainboard/pcengines/alix2d/Kconfig +++ b/src/mainboard/pcengines/alix2d/Kconfig @@ -10,6 +10,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select PIRQ_ROUTE select UDELAY_TSC select BOARD_ROMSIZE_KB_512 + select POWER_BUTTON_FORCE_DISABLE config MAINBOARD_DIR string diff --git a/src/mainboard/pcengines/alix2d/romstage.c b/src/mainboard/pcengines/alix2d/romstage.c index aa5f7a0fc4..10ab27d662 100644 --- a/src/mainboard/pcengines/alix2d/romstage.c +++ b/src/mainboard/pcengines/alix2d/romstage.c @@ -120,12 +120,6 @@ static u8 spd_read_byte(u8 device, u8 address) static void mb_gpio_init(void) { /* - * Disable power button, since it is hardwired to ground on this board, - * and the power would be cut off atfer a 4-second delay otherwise. - */ - outl(0x00020000, PMS_IO_BASE + 0x40); - - /* * Enable LEDs GPIO outputs to light up the leds * This is how the original tinyBIOS sets them after boot. * Info: GPIO_IO_BASE, 0x6100, is only valid before PCI init, so it diff --git a/src/mainboard/traverse/geos/Kconfig b/src/mainboard/traverse/geos/Kconfig index 1c85149671..dd6c8dd9fa 100644 --- a/src/mainboard/traverse/geos/Kconfig +++ b/src/mainboard/traverse/geos/Kconfig @@ -10,6 +10,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select PIRQ_ROUTE select UDELAY_TSC select BOARD_ROMSIZE_KB_1024 + select POWER_BUTTON_DEFAULT_DISABLE config MAINBOARD_DIR string diff --git a/src/mainboard/winent/pl6064/Kconfig b/src/mainboard/winent/pl6064/Kconfig index 1ec56929d5..4f367f1fab 100644 --- a/src/mainboard/winent/pl6064/Kconfig +++ b/src/mainboard/winent/pl6064/Kconfig @@ -11,6 +11,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select PIRQ_ROUTE select UDELAY_TSC select BOARD_ROMSIZE_KB_512 + select POWER_BUTTON_FORCE_ENABLE config MAINBOARD_DIR string diff --git a/src/mainboard/wyse/s50/Kconfig b/src/mainboard/wyse/s50/Kconfig index 75b5335717..dae8cdb2a2 100644 --- a/src/mainboard/wyse/s50/Kconfig +++ b/src/mainboard/wyse/s50/Kconfig @@ -28,6 +28,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select HAVE_PIRQ_TABLE select PIRQ_ROUTE select BOARD_ROMSIZE_KB_256 + select POWER_BUTTON_FORCE_DISABLE config MAINBOARD_DIR string diff --git a/src/mainboard/wyse/s50/romstage.c b/src/mainboard/wyse/s50/romstage.c index d36173cee1..a77760d6ef 100644 --- a/src/mainboard/wyse/s50/romstage.c +++ b/src/mainboard/wyse/s50/romstage.c @@ -134,9 +134,6 @@ void main(unsigned long bist) cs5536_early_setup(); - /* disable the power button */ - outl(0x00, PMS_IO_BASE + 0x40); - /* cs5536_disable_internal_uart disable them. Set them up now... */ cs5536_setup_onchipuart(1); diff --git a/src/southbridge/amd/cs5536/cs5536_early_setup.c b/src/southbridge/amd/cs5536/cs5536_early_setup.c index 452e530f41..047c1a21a0 100644 --- a/src/southbridge/amd/cs5536/cs5536_early_setup.c +++ b/src/southbridge/amd/cs5536/cs5536_early_setup.c @@ -92,8 +92,9 @@ static void cs5536_setup_iobase(void) static void cs5536_setup_power_button(void) { - /* Power Button Setup */ +#if CONFIG_ENABLE_POWER_BUTTON outl(0x40020000, PMS_IO_BASE + 0x40); +#endif /* setup WORK_AUX/GPIO24, it is the external signal for 5536 * vsb_work_aux controls all voltage rails except Vstandby & Vmem. |